足式机器人SLIP模型向上跳跃台阶的运动控制

由于存在地势起伏,台阶对足式机器人运动稳定性会带来较大挑战.弹簧负载倒立摆模型(SLIP)作为研究足式机器人的优良模板,能否完成向上跳跃台阶的动作与其腿部摆角,起跳位置和跳跃高度都有密切的关系.由于调整模型腿部摆角规律容易引发运动失效,故本文在算法中引入虚拟弹簧腿,根据虚拟弹簧腿的运行规律确定合理起跳位置,根据起跳位置来控制系统跳跃高度进而完成跳跃台阶的动作.最后利用仿真软件进行多组仿真,结果表明本文算法对起跳区间划分合理,对起跳高度控制精准,能够实现SLIP模型跳跃台阶前后的稳定运动.

液体润滑浸渍表面(SLIPS)船舶防污涂层最新研究进展

综述了近3年来关于液体润滑浸渍表面(SLIPS)船舶防污涂层的研究进展,特别是润滑液的选择与涂层的结构设计,以及这些因素如何影响涂层的整体性能,以期为未来的研究提供最新思路及研究方法。

Revealing the role of pyramidal slip in the high ductility of Mg-Li alloy

The high ductility of Mg-Li alloy has been mainly ascribed to a high activity of pyramidal<c+a>slip to accommodate plastic strain.In the present study,however,a quantitative analysis reveals that Li-addition can only slightly stimulate the activation of pyramidal<c+a>slip under compression along the normal direction of a hot-rolled Mg-4.5 wt.%Li plate,with a relative activity of approximately 18%.Although the limited activity of pyramidal<c+a>slip alone cannot accommodate a large plastic strain,it effectively reduces the number of{10.11}−{10.12}double twins,which are believed to be favorable sites for crack initiation.The evidently reduced activity of double twins leads to a lower cracking tendency,and therefore improves ductility.

Coseismic deformation and fault slip distribution of the 2023 M_(W)7.8 and M_(W)7.6 earthquakes in Türkiye

On February 6,2023,a devastating earthquake with a moment magnitude of M_(W)7.8 struck the town of Pazarcik in south-central Türkiye,followed by another powerful earthquake with a moment magnitude of M_(W)7.6 that struck the nearby city of Elbistan 9 h later.To study the characteristics of surface deformation caused by this event and the influence of fault rupture,this study calculated the static coseismic deformation of 56 stations and dynamic displacement waveforms of 15 stations using data from the Turkish national fixed global navigation satellite system(GNSS)network.A maximum static coseismic displacement of 0.38 m for the M_(W)7.8 Kahramanmaras earthquake was observed at station ANTE,36 km from the epicenter,and a maximum dynamic coseismic displacement of 4.4 m for the M_(W)7.6 Elbistan earthquake was observed at station EKZ1,5 km from the epicenter.The rupture-slip distributions of the two earthquakes were inverted using GNSS coseismic deformation as a constraint.The results showed that the Kahramanmaras earthquake rupture segment was distinct and exposed on the ground,resulting in significant rupture slip along the Amanos and Pazarcik fault segments of the East Anatolian Fault.The maximum slip in the Pazarcik fault segment was 10.7 m,and rupture occurred at depths of 0–15 km.In the Cardak fault region,the Elbistan earthquake caused significant ruptures at depths of 0–12 km,with the largest amount of slip reaching 11.6 m.The Coulomb stress change caused by the Kahramanmaras earthquake rupture along the Cardak fault segment was approximately 2 bars,and the area of increased Coulomb stress corresponded to the subsequent rupture region of the M_(W)7.6 earthquake.Thus,it is likely that the M_(W)7.8 earthquake triggered or promoted the M_(W)7.6 earthquake.Based on the cumulative stress impact of the M_(W)7.8 and M_(W)7.6 events,the southwestern segment of the East Anatolian Fault,specifically the Amanos fault segment,experienced a Coulomb rupture stress change exceeding 2 bars,warranting further attention to assess its future seismic hazard risk.

Experimental investigation on fluid-induced slip behavior of fault filled with fault gouge

Fault zones are usually filled with fault gouge and accompanied by fault water.The coupled effect of fault gouge and water significantly impacts the slip behavior of the fault,which may weaken the fault structure and further induce rupture propagation and earthquakes.In this study,we carried out a laboratory experiment to investigate the fluid-induced slip behavior of fault filled with gouge.The friction evolution characteristic associated with fluid pressure and effective stress was investigated during the slip process.In addition,the role transformation process of the gouge on the slip behavior of fault was revealed.The experimental result indicates that the friction on the filled fault surface is significantly affected by fault gouge.The rupture of the gouge promotes fault slip and the fluid pressure plays a vital role in the initiation of fault slip.The fault gouge enhances the shearing strength of the fault and acts as a barrier before the initial slip under fluid injection.Nevertheless,the fault gouge would accelerate the fault slip and transform into lubricant after the initial slip.

Effect of boundary slip on electroosmotic flow in a curved rectangular microchannel

The aim of this study is to numerically investigate the impact of boundary slip on electroosmotic flow(EOF) in curved rectangular microchannels. Navier slip boundary conditions were employed at the curved microchannel walls. The electric potential distribution was governed by the Poisson–Boltzmann equation, whereas the velocity distribution was determined by the Navier–Stokes equation. The finite-difference method was employed to solve these two equations. The detailed discussion focuses on the impact of the curvature ratio, electrokinetic width, aspect ratio and slip length on the velocity. The results indicate that the present problem is strongly dependent on these parameters. The results demonstrate that by varying the dimensionless slip length from 0.001 to 0.01 while maintaining a curvature ratio of 0.5 there is a twofold increase in the maximum velocity. Moreover, this increase becomes more pronounced at higher curvature ratios. In addition, the velocity difference between the inner and outer radial regions increases with increasing slip length. Therefore, the incorporation of the slip boundary condition results in an augmented velocity and a more non-uniform velocity distribution. The findings presented here offer valuable insights into the design and optimization of EOF performance in curved hydrophobic microchannels featuring rectangular cross-sections.

Co and postseismic fault slip models of the 2022 M_(W)6.7 Menyuan earthquake reveal conjugated faulting tectonics at the central section of the Lenglongling fault

The 2022 M_(W)6.7 Menyuan earthquake ruptured the western end of the Tianzhu seismic gap,providing an opportunity to study the regional seismogenic characteristics and seismic hazards.Here we use interferometric synthetic aperture radar(InSAR)and seismic data to study the mainshock rupture,early afterslip and the second largest aftershock of the 2022 Menyuan earthquake sequences.Our modeling results show that the mainshock ruptured the Lenglongling fault and the Tuolaishan fault with a maximum slip of~3 m.Rapid postseismic transient deformation occurred at the center of the Lenglongling fault.Our afterslip modeling reveals that the majority of afterslip occurred in the deeper part of the Lenglongling fault.A high-angle conjugated faulting event is found at the middle section of the Lenglongling fault.We use the stress inversion to investigate the possible triggering mechanism of the conjugated rupture event.The results indicate the maximum principal stress direction is in~222°,forming a~22°angle between the conjugated fault of second largest aftershock and the mainshock.The calculated normal stress changes indicate the region is within a pull-apart stress field,which favors such a conjugated rupturing event.Our study will help understand the rupture behavior of such kind of conjugated fault in other regions.

Interseismic slip distribution and locking characteristics of the mid-southern segment of the Tanlu fault zone

We employ the block negative dislocation model to invert the distribution of fault coupling and slip rate deficit on the different segments of the Tanlu(Tancheng-Lujiang) fault zone, according to the GPS horizontal velocity field from 1991 to 2007(the first phase) and 2013 to 2018(the second phase). By comparing the deformation characteristics results, we discuss the relationship between the deformation characteristics with the M earthquake in Japan. The results showed that the fault coupling rate of the northern section of Tancheng in the second phase reduced compared with that in the first phase. However, the results of the two phases showed that the northern section of Juxian still has a high coupling rate, a deep blocking depth, and a dextral compressive deficit, which is the enrapture section of the 1668 Tancheng earthquake. At the same time, the area strain results show that the strain rate of the central and eastern regions of the second phase is obviously enhanced compared with that of the first phase. The occurrence of the great earthquake in Japan has played a specific role in alleviating the strain accumulation in the middle and south sections of the Tanlu fault zone. The results of the maximum shear strain show that the shear strain in the middle section of the Tanlu fault zone in the second phase is weaker than that in the first phase, and the maximum shear strain in the southern section is stronger than that in the first phase. The fault coupling coefficient of the south Sihong to Jiashan section is high, and it is also the unruptured section of historical earthquakes. At the same time, small earthquakes in this area are not active and accumulate stress easily, so the future earthquake risk deserves attention.

Risk factors and clinical significance of posterior slip of the proximal vertebral body after lower lumbar fusion

BACKGROUND Adjacent segment disease(ASD)after fusion surgery is frequently manifests as a cranial segment instability,disc herniation,spinal canal stenosis,spondylolisthesis or retrolisthesis.The risk factors and mechanisms of ASD have been widely discussed but never clearly defined.AIM To investigate the risk factors and clinical significance of retrograde movement of the proximal vertebral body after lower lumbar fusion.METHODS This was a retrospective analysis of the clinical data of patients who underwent transforaminal lumbar interbody fusion surgery between September 2015 and July 2021 and who were followed up for more than 2 years.Ninety-one patients with degenerative lumbar diseases were included(22 males and 69 females),with an average age of 52.3 years(40-73 years).According to whether there was retrograde movement of the adjacent vertebral body on postoperative X-rays,the patients were divided into retrograde and nonretrograde groups.The sagittal parameters of the spine and pelvis were evaluated before surgery,after surgery,and at the final follow-up.At the same time,the Oswestry Disability Index(ODI)and Visual Analogue Scale(VAS)were used to evaluate the patients’quality of life.RESULTS Nineteen patients(20.9%)who experienced retrograde movement of proximal adjacent segments were included in this study.The pelvic incidence(PI)of the patients in the retrograde group were significantly higher than those of the patients in the nonretrograde group before surgery,after surgery and at the final follow-up(P<0.05).There was no significant difference in lumbar lordosis(LL)between the two groups before the operation,but LL in the retrograde group was significantly greater than that in the nonretrograde group postoperatively and at the final follow-up.No significant differences were detected in terms of the|PI–LL|,and there was no significant difference in the preoperative lordosis distribution index(LDI)between the two groups.The LDIs of the retrograde group were 68.1%±11.5%and 67.2%±11.9%,respectively,which were significantly lower than those of the nonretrograde group(75.7%±10.4%and 74.3%±9.4%,respectively)(P<0.05).Moreover,the patients in the retrograde group had a greater incidence of a LDI<50%than those in the nonretrograde group(P<0.05).There were no significant differences in the ODI or VAS scores between the two groups before the operation,but the ODI and VAS scores in the retrograde group were significantly worse than those in the nonretrograde group after the operation and at the last follow-up,(P<0.05).CONCLUSION The incidence of posterior slippage after lower lumbar fusion was approximately 20.9%.The risk factors are related to a higher PI and distribution of lumbar lordosis.When a patient has a high PI and insufficient reconstruction of the lower lumbar spine,adjacent segment compensation via posterior vertebral body slippage is one of the factors that significantly affects surgical outcomes.

A Large-Scale Palaeozoic Dextral Ductile Strike-Slip Zone:the Aqqikkudug-Weiya Zone along the Northern Margin of the Central Tianshan Belt,Xinjiang,NW China

Abstract The nearly E-W-trending Aqqikkudug-Weiya zone, more than 1000 km long and about 30 km wide, is an important segment in the Central Asian tectonic framework. It is distributed along the northern margin of the Central Tianshan belt in Xinjiang, NW China and is composed of mylonitized Early Palaeozoic greywacke, volcanic rocks, ophiolitic blocks as a mélange complex, HP/LT-type bleuschist blocks and mylonitized Neoproterozoic schist, gneiss and orthogneiss. Nearly vertical mylonitic foliation and sub-horizontal stretching lineation define its strike-slip feature; various kinematic indicators, such as asymmetric folds, non-coaxial asymmetric macro- to micro-structures and C-axis fabrics of quartz grains of mylonites, suggest that it is a dextral strike-slip ductile shear zone oriented in a nearly E-W direction characterized by “flower” strusture with thrusting or extruding across the zone toward the two sides and upright folds with gently plunging hinges. The Aqqikkudug-Weiya zone experienced at least two stages of ductile shear tectonic evolution: Early Palaeozoic north vergent thrusting ductile shear and Late Carboniferous-Early Permian strike-slip deformation. The strike-slip ductile shear likely took place during Late Palaeozoic time, dated at 269±5 Ma by the40Ar/39Ar analysis on neo-muscovites. The strike-slip deformation was followed by the Hercynian violent S-type granitic magmatism. Geodynamical analysis suggests that the large-scale dextral strike-slip ductile shearing is likely the result of intracontinental adjustment deformation after the collision of the Siberian continental plate towards the northern margin of the Tarim continental plate during the Late Carboniferous. The Himalayan tectonism locally deformed the zone, marked by final uplift, brittle layer-slip and step-type thrust faults, transcurrent faults and E-W-elongated Mesozoic-Cenozoic basins.

The Dihedral Angle and Intersection Processes of a Conjugate Strike-Slip Fault System in the Tarim Basin, NW China

Recent studies, focused on dihedral angles and intersection processes, have increased understandings of conjugate fault mechanisms. We present new 3-D seismic data and microstructural core analysis in a case study of a large conjugate strike-slip fault system from the intracratonic Tarim Basin, NW China. Within our study area, ＂X＂ type NE and NW trending faults occur within Cambrian- Ordovician carbonates. The dihedral angles of these conjugate faults have narrow ranges, 19~ to 62~ in the Cambrian and 26~ to 51~ in the Ordovician, and their modes are 42~ and 44~ respectively. These data are significantly different from the ~60~ predicted by the Coulomb fracture criterion. It is concluded that： （1） The dihedral angles of the conjugate faults were not controlled by confining pressure, which was low and associated with shallow burial; （2） As dihedral angles were not controlled by pressure they can be used to determine the shortening direction during faulting; （3） Sequential slip may have played an important role in forming conjugate fault intersections; （4） The conjugate fault system of the Tarim basin initiated as rhombic joints; these subsequently developed into sequentially active ＂X＂ type conjugate faults; followed by preferential development of the NW-trending faults; then reactivation of the NE trending faults. This intact rhombic conjugate fault system presents new insights into mechanisms of dihedral angle development, with particular relevance to intracratonic basins.

Uniform Strike-Slip Rate along the Xianshuihe-Xiaojiang Fault System and Its Implications for Active Tectonics in Southeastern Tibet

Recent studies on the Xianshuihe-Xiaojiang fault system suggest that the Late Quaternary strike-slip rate is approximately uniform along the entire length of the fault zone, about 15±2 mm/a. This approximately uniform strike slip rate strongly supports the clockwise rotation model of the southeastern Tibetan crust. By approximating the geometry of the arc-shaped Xianshuihe-Xiaojiang fault system as a portion of a small circle on a spherical Earth, the 15±2 mm/a strike slip rate corresponds to clockwise rotation of the Southeastern Tibetan Block at the （5.2±0.7）×10^-7 deg/a angular velocity around the pole （21°N, 88°E） relative to the Northeast Tibetan Block. The approximately uniform strike slip rate along the Xianshuihe-Xiaojiang fault system also implies that the Longmeushan thrust zone is not active, or at least its activity has been very weak since the Late Quaternary. Moreover, the total offset along the Xiaushuihe-Xiaojiang fault system suggests that the lateral extrusion of the Southeastern Tibetan Block relative to Northeastern Tibetan Block is about 160 km and 200-240 km relative to the Tarim-North China block. This amount of lateral extrusion of the Tibetan crust should have accommodated about 13-24% convergence between India and Eurasia based on mass balance calculations. Assuming that the slip rate of 15±2 mm/a is constant throughout the entire history of the Xianshuihe-Xiaojiang fault system, 11±1.5 Ma is needed for the Xianshuihe-Xiaojiang fault system to attain the 160 km of total offset. This implies that left-slip faulting on the Xianshuihe-Xiaojiang fault system might start at 11±1.5 Ma.

Characteristics of strike-slip inversion structures of the Karatau fault and their petroleum geological significances in the South Turgay Basin,Kazakhstan

The Karatau fault is one of the important strike-slip faults in central Asia,and the South Turgay Basin is located towards its northern end.Detailed seismic interpretation indicated that the strikeslip tectonism of the Karatau fault weakened gradually from west to east in the South Turgay Basin.Typical flower structures developed on the section,and strike-slip faults showed an echelon pattern on planar view.The Karatau strike-slip fault affected the South Turgay Basin in two periods：（1） The South Turgay strike-slip pull-apart rift basin formed as a result of regional extensive stress in the Early-Middle Jurassic,characterized by the juxtaposition of horsts and grabens.The formation of horsts provided favorable reservoir spaces for later hydrocarbon accumulation,and different filling stages of grabens controlled different reservoir-forming factors in grabens.（2） Two stages of tectonic inversion occurred in the Late Jurassic and Late Cretaceous and played a crucial role in the final shape of the structure in the South Turgay Basin.The oil and gas migrated to form reservoirs and mainly concentrated in the horsts,graben slopes and in both sides of the strike-slip fault zone.In the case of the degree of accumulation of petroleum,the factor explaining why horsts are better than grabens is the strike-slip pull-apart of the South Turgay Basin,and the structure inversion of the South Turgay Basin explains why the west graben is better than the east one.Overall,the Karatau strike-slip fault played a very important role in the formation of the South Turgay Basin and its hydrocarbon accumulations.

Characteristics and evolution of strike-slip tectonics of the Liaohe Western Sag,Bohai Bay Basin

Because of its rich oil and gas resources and the special tectonic location of the Liaohe Western Sag （the Tanlu Fault traverses the sag）, Bohai Bay Basin, a detailed study of its strike-slip tectonics is significant in revealing the sag＇s tectonic evolution, its control on hydrocarbon accumulation, and the activity history of the northern section of the Tanlu Fault in the Cenozoic. Through systematic structure analysis of 3D seismic data of the Liaohe Western Sag, combined with balanced section analysis, a variety of structural features in relation to right-lateral strike-slip faults, such as echelon normal faults, ＂comb＂ structure, ＂flower＂ structure,＂interpretable＂ and ＂buried＂ strike-slip faults have been revealed exist in the Liaohe Western Sag. According to the research in this paper, the complex structural phenomena in the Liaohe Western Sag could be reasonably interpreted as right-lateral strike-slip activity and the strike-slip activities of the Liaohe Western Sag began in the early Oligocene. The activity was weak at the beginning （E3s1-2）, then strengthened gradually and reached its strongest level in the late Oligocene （E3d1）. In the Miocene, the strike-slip activity was low and then strengthened significantly once again from the Pliocene to the present. It is speculated that the entire northern section of the Tanlu Fault has had a similar evolution history since the Oligocene.

Neotectonics of the Eastern Margin of the Tibetan Plateau: New Geological Evidence for the Change from Early Pleistocene Transpression to Late Pleistocene-Holocene Strike-slip Faulting

We present in this paper some new evidence for the change during the Quaternary in kinematics of faults cutting the eastern margin of the Tibetan Plateau. It shows that significant shortening deformation occurred during the Early Pleistocene, evidenced by eastward thrusting of Mesozoic carbonates on the Pliocene lacustrine deposits along the Minjiang upstream fault zone and by development of the transpressional ridges of basement rocks along the Anninghe river valley. The Middle Pleistocene seems to be a relaxant stage with local development of the intra-mountain basins particularly prominent along the Minjiang Upstream and along the southern segment of the Anninghe River Valley. This relaxation may have been duo to a local collapse of the thickened crust attained during the late Neogene to early Pleistocene across this marginal zone. Fault kinematics has been changed since the late Pleistocene, and was predominated by reverse sinistral strike-slip along the Minshan Uplift, reverse dextral strike-slip on the Longmenshan fault zone and pure sinistral strike-slip on the Anninghe fault. This change in fault kinematics during the Quaternary allows a better understanding of the mechanism by which the marginal ranges of the plateau has been built through episodic activities.

Characteristics of the Late Quaternary right-lateral strike-slip movement of Bolokenu-Aqikekuduk fault in northern Tianshan Mountains,NW China

The characteristics of the Bolokenu-Aqikekuduk（Bo-A） fault,a right-lateral strike-slip fault that runs for more than 700 km long and obliquely cuts North Tianshan Mountains,are evaluated here based on remote sensing data,and through an analysis of the results from field investigations as well as climate-geomorphic events. The fault is composed of a western segment with a NW strike and an eastern segment with a NWW strike.The western segment is nearly 250 km long,extending northwestward into Kazakhstan with a right-lateral strike-slip rate of 5 mm/a.This domain consists of 4-5 rupture sections,with 3-4 deformation belts,caused by ancient or historical earthquakes,and suggesting the potential for the occurrence of further strong earthquakes（with M≈7.5） in future. The eastern segment of the fault shows a right-lateral strike-slip rate of 1-1.4 mm/a,with the development of 3-4 deformation belts caused by ancient or historical earthquakes,and with a potential for future strong earthquake with M≈7.0. A typical strain partitioning style in the compression area has developed between the intermontane BoA fault and the piedmont thrust structures of Northern Tianshan Mountains,under the effect of oblique compression,as indicated by the piedmont thrust structure and the strike-slip fault in the mountains.

TWO PHASES OF CENOZOIC DEFORMATION IN NORTHEASTERN TIBET: THRUSTING FOLLOWED BY STRIKE-SLIP FAULTING

In order to establish deformation history for the Cenozoic development of the Tibetan Plateau, we conducted geologic mapping along a 120km traverse between Nangqian and Yushu in the northeastern Qiangtang terrane. This work reveals a complex interaction among Tertiary thrusting, strike\|slip faulting, sedimentation, and igneous activity. Two phases of deformation are recognized. The older northeast—southwest shortening, expressed by thrusting and folding, is followed by left\|slip faulting along northwest\|trending faults. Tertiary thrusts, predominantly southwest\|dipping, are distributed throughout the traverse, and typically juxtapose Mesozoic strata over Paleogene strata. The latter were deposited in several separated basins during folding and thrusting, as indicated by well\|developed growth strata. A preliminary construction of balanced cross\|sections suggests a minimum estimate of 45km of crustal shortening along the traverse. Numerous hypabyssal intrusions were mapped in the southern part of the traverse near Nangqian. They were emplaced into the Paleogene sediments and are dated between 36 and 33Ma by 40 Ar/ 39 Ar and U\|Pb methods. Paleogene sediments are also interbedded with volcanics in both the southern and northern parts of the study area. In the northernmost part of the traverse, a volcanic unit overlies a Tertiary thrust. This unit itself is broadly folded. This relationship suggests that Tertiary igneous activity was coeval with contractional deformation in the region, implying strongly the causal relationship between the two processes. The youngest event in the area is the development of northwest\|trending left\|slip faults. They cut Tertiary thrusts, folds, and about 35Ma igneous intrusions. In contrast to widely distributed Tertiary folds and thrusts, strike\|slip faulting is restricted only to the southern portion of our mapped area near Nangqian. The strike\|slip faults apparently control the distribution of modern drainage systems, suggesting that they may have been active recently. As the younger strike\|slip faults are subparallel to the older folds and thrusts, we have not been able to determine the magnitude of left\|slip on these faults. We interpret the termination of contractional deformation and the subsequent replacement by strike\|slip faulting as a result of both clockwise rotation of the region and westward propagation of strike\|slip deformation in eastern Tibet.

Evolution of the deformation field and earthquake fracture precursors of strike-slip faults

Seismic hazard analysis is gaining increased attention in the present era because of the catastrophic effects of earthquakes.Scientists always have as a goal to develop new techniques that will help forecast earthquakes before their reoccurrence. In this research,we have performed a shear failure experiment on rock samples with prefabricated cracks to simulate the process of plate movement that forms strike-slip faults. We studied the evolution law of the deformation field to simulate the shear failure experiment, and these results gave us a comprehensive understanding of the elaborate strain distribution law and its formation process with which to identify actual fault zones. We performed uniaxial compression tests on marble slabs with prefabricated double shear cracks to study the distribution and evolution of the deformation field during shear failure. Analysis of the strain field at different loading stages showed that with an increase in the load, the shear strain field initially changed to a disordered-style distribution. Further, the strain field was partially concentrated and finally completely concentrated near the crack and then distributed in the shape of a strip along the crack. We also computed coefficients of variation(CVs) for the physical quantities u, v, and exy, which varied with the load. The CV curves were found to correspond to the different loading stages. We found that at the uniform deformation stage, the CV value was small and changed slowly,whereas at the later nonuniform deformation stage, the CV value increased sharply and changed abruptly. Therefore, the precursor to a rock sample breakdown can be predicted by observing the variation characteristics of CV statistics. The correlation we found between our experimental and theoretical results revealed that our crack evolution and sample deformation results showed good coupling with seismic distribution characteristics near the San Andreas Fault.

On the faults of western Hexi Corridor and its nearby regions, northwestern China: Thrust faults and strike-slip faults of Late Cenozoic

The structural analysis based on the explanation of seismic profiles indicates that a lot of thrust faults and strike-slip faults of Late Cenozoic occur in western Hexi Corridor and its nearby regions. They can be divided into two types. One is thrust faults dipping southwards and extending NWwards, which was mainly correlated with the thrusting of northern Qilianshan and located at the NE margin of Qilianshan and the southwestern Hexi Corridor, the other is thrust faults and strike-slip faults that were related to the strike-slipping of Altun fault and located mainly at the regions of Hongliuxia, Kuantaishan, and Helishan that are close to the Altun fault. All these faults, which were related to the remote effects of collision between the two continents of India and Tibet during the Late Eocene and later, started to develop since the Late Tertiary and presented the features of violent thrust or strike-slip movement in Quaternary. Many of them are still active up to now and thus belong to the active faults that are the potential inducement of earthquakes in the Hexi Corridor. Moreover, a lot of intense structural deformation and many morphology phenomena such as tectonic terrace and river offset were formed under the control of these faults in Quaternary.

Decadal Seismicity before Great Earthquakes—Strike-Slip Faults and Plate Interiors: Major Asperities and Low-Coupling Zones

Decadal forerunning seismic activity is examined for very large, shallow earthquakes along strike-slip and intraplate faults of the world. It includes forerunning shocks of magnitude Mw ≥ 5.0 for 21 mainshocks of Mw 7.5 to 8.6 from 1989 to 2020. Much forerunning activity occurred at what are interpreted to be smaller asperities along the peripheries of the rupture zones of great mainshocks at transform faults and subduction zones. Several great asperities as ascertained from forerunning activity agree with the areas of high seismic slip as determined by others using geodetic, mapping of surface faulting, and finite-source seismic modeling. The zones of high slip in many great earthquakes were nearly quiescent beforehand and are identified as the sites of great asperities. Asperities are strong, well-coupled portions of plate interfaces. Different patterns of forerunning activity on time scales of up to 45 years are attributed to the sizes and spacing of asperities (or lack of). This permits at least some great asperities along transform faults to be mapped decades before they rupture in great shocks. Rupture zones of many great mainshocks along transform faults are bordered either along strike, at depth or regionally by zones of lower plate coupling including either fault creep forerunning activity, aftershocks and/or slow-slip events. Forerunning activity to transforms in continental areas is more widespread spatially than that adjacent to oceanic transforms. The parts of the San Andreas fault themselves that ruptured in great California earthquakes during 1812, 1857 and 1906 have been very quiet since 1920;moderate to large shocks have been concentrated on their peripheries. The intraplate shocks studied, however, exhibited few if any forerunning events, which is attributed to the short period of time studied compared to their repeat times. The detection of forerunning and precursory activities for various time scales should be sought on the peripheries of great asperities and not just along the major faults themselves. This paper compliments that on decadal forerunning activity to great and giant earthquakes along subduction zones.