The values of direct double- to-single ionization ratio R of helium atoms induced by C^q＋, O^q＋ （q = 1 -4） ions at incident energies from 0.2 to 8.5MeV are measured. Based on the existing model （Shao J X, Chen X ...The values of direct double- to-single ionization ratio R of helium atoms induced by C^q＋, O^q＋ （q = 1 -4） ions at incident energies from 0.2 to 8.5MeV are measured. Based on the existing model （Shao J X, Chen X M and Ding B W 2007 Phys. Rev. A 75 012701） the effective charge of the projectile is introduced to theoretically estimate the value of R for the partially stripped ions impacting on helium atoms. The results calculated from our ＂effective charge＂ model are in good agreement with the experimental data, and the dependence of the effective charge on the ionization energy of the projectile is also discussed qualitatively.展开更多
Charge stripping is employed to produce multi-charged ions for injecting the cooling storage ring.After penetrating through the carbon foil,the widened distribution of ion charge states poses a limit to the ion inject...Charge stripping is employed to produce multi-charged ions for injecting the cooling storage ring.After penetrating through the carbon foil,the widened distribution of ion charge states poses a limit to the ion injection.Therefore,the carbon foil plays a key role in the charge stripping injection.In this paper,four strippers for Heavy Ion Research Facility at Lanzhou(HIRFL) and Cooling Storage Ring(CSR) are introduced.The charge state distribution of the stripped ions is measured and the stripping efficiency of the foils is investigated.The experimental results are consistent with the theoretical values.展开更多
The finite strip method in structural analysis has been extended, and elastic-plastic large deformation spline finite strip method based on the Updated-Lagrange method (U. L. method) was established to simulate roll f...The finite strip method in structural analysis has been extended, and elastic-plastic large deformation spline finite strip method based on the Updated-Lagrange method (U. L. method) was established to simulate roll forming process of channel section with outer edge. The deformation characteristics of strip was analyzed, and the three-dimensional displacement field, strain field and stress field of deformed strip were got. The calculation example proves that the peak transverse pressing membrane strain is on the corner part of the deformed strip, and the peak longitudinal stretching strain is on the outer edge part of the deformed strip in front of rolls. In addition, the transverse deformation of the deformed strip is principal, and the longitudinal deformation is small.展开更多
The cross-section profile is a key signal for evaluating hot-rolled strip quality,and ignoring its defects can easily lead to a final failure.The characteristics of complex curve,significant irregular fluctuation and ...The cross-section profile is a key signal for evaluating hot-rolled strip quality,and ignoring its defects can easily lead to a final failure.The characteristics of complex curve,significant irregular fluctuation and imperfect sample data make it a challenge of recognizing cross-section defects,and current industrial judgment methods rely excessively on human decision making.A novel stacked denoising autoencoders(SDAE)model optimized with support vector machine(SVM)theory was proposed for the recognition of cross-section defects.Firstly,interpolation filtering and principal component analysis were employed to linearly reduce the data dimensionality of the profile curve.Secondly,the deep learning algorithm SDAE was used layer by layer for greedy unsupervised feature learning,and its final layer of back-propagation neural network was replaced by SVM for supervised learning of the final features,and the final model SDAE_SVM was obtained by further optimizing the entire network parameters via error back-propagation.Finally,the curve mirroring and combination stitching methods were used as data augmentation for the training set,which dealt with the problem of sample imbalance in the original data set,and the accuracy of cross-section defect prediction was further improved.The approach was applied in a 1780-mm hot rolling line of a steel mill to achieve the automatic diagnosis and classification of defects in cross-section profile of hot-rolled strip,which helps to reduce flatness quality concerns in downstream processes.展开更多
基金Project supported by the National Natural Science Foundation of China (Grant No 10775063)
文摘The values of direct double- to-single ionization ratio R of helium atoms induced by C^q＋, O^q＋ （q = 1 -4） ions at incident energies from 0.2 to 8.5MeV are measured. Based on the existing model （Shao J X, Chen X M and Ding B W 2007 Phys. Rev. A 75 012701） the effective charge of the projectile is introduced to theoretically estimate the value of R for the partially stripped ions impacting on helium atoms. The results calculated from our ＂effective charge＂ model are in good agreement with the experimental data, and the dependence of the effective charge on the ionization energy of the projectile is also discussed qualitatively.
基金Supported by Funds of the National Natural Science Foundation of China(Grant No:10575120)
文摘Charge stripping is employed to produce multi-charged ions for injecting the cooling storage ring.After penetrating through the carbon foil,the widened distribution of ion charge states poses a limit to the ion injection.Therefore,the carbon foil plays a key role in the charge stripping injection.In this paper,four strippers for Heavy Ion Research Facility at Lanzhou(HIRFL) and Cooling Storage Ring(CSR) are introduced.The charge state distribution of the stripped ions is measured and the stripping efficiency of the foils is investigated.The experimental results are consistent with the theoretical values.
文摘The finite strip method in structural analysis has been extended, and elastic-plastic large deformation spline finite strip method based on the Updated-Lagrange method (U. L. method) was established to simulate roll forming process of channel section with outer edge. The deformation characteristics of strip was analyzed, and the three-dimensional displacement field, strain field and stress field of deformed strip were got. The calculation example proves that the peak transverse pressing membrane strain is on the corner part of the deformed strip, and the peak longitudinal stretching strain is on the outer edge part of the deformed strip in front of rolls. In addition, the transverse deformation of the deformed strip is principal, and the longitudinal deformation is small.
基金supported by the National Natural Science Foundation of China(No.52004029)the Joint Doctoral Program of China Scholarship Council(CSC)(202006460073)Liuzhou Science and Technology Plan Project,China(2021AAD0102).
文摘The cross-section profile is a key signal for evaluating hot-rolled strip quality,and ignoring its defects can easily lead to a final failure.The characteristics of complex curve,significant irregular fluctuation and imperfect sample data make it a challenge of recognizing cross-section defects,and current industrial judgment methods rely excessively on human decision making.A novel stacked denoising autoencoders(SDAE)model optimized with support vector machine(SVM)theory was proposed for the recognition of cross-section defects.Firstly,interpolation filtering and principal component analysis were employed to linearly reduce the data dimensionality of the profile curve.Secondly,the deep learning algorithm SDAE was used layer by layer for greedy unsupervised feature learning,and its final layer of back-propagation neural network was replaced by SVM for supervised learning of the final features,and the final model SDAE_SVM was obtained by further optimizing the entire network parameters via error back-propagation.Finally,the curve mirroring and combination stitching methods were used as data augmentation for the training set,which dealt with the problem of sample imbalance in the original data set,and the accuracy of cross-section defect prediction was further improved.The approach was applied in a 1780-mm hot rolling line of a steel mill to achieve the automatic diagnosis and classification of defects in cross-section profile of hot-rolled strip,which helps to reduce flatness quality concerns in downstream processes.
