SiCp/Al复合材料纳米压痕/划痕下的脆塑性行为研究

为探究SiCp/Al复合材料中两相材料相互作用引起的力学性能差异,研究微观尺度下法向载荷变化对SiCp/Al复合材料形变和去除的影响。采用纳米压痕实验,基于Oliver-Pharr法测得其硬度和弹性模量,并对其压痕表面进行观察,结合有限元仿真分析产生力学性能差异的原因;同时,根据纳米压痕实验所得力学参数进行变载荷纳米划痕仿真,并配合实验后划痕表面观察结果分析材料的形变和脆塑性行为。结果表明:当金刚石压头作用于SiC颗粒时,颗粒出现破碎和二次压入现象,所测硬度与弹性模量小于单晶SiC的理论值;当金刚石压头作用于基体相时,由于SiC颗粒阻碍基体压入,复合材料的硬度与弹性模量测量结果偏大。在纳米划痕过程中,复合材料的去除形式随载荷变化体现为划擦、耕犁和切削阶段,其中的基体相通过塑性流动产生塑性脊堆积并伴随有涂覆现象,SiC颗粒则以脱黏、断裂破碎和拔出等脆性机制而去除,且SiC颗粒的二次压入、断裂、破碎和拔出是导致复合材料力学性能与单晶SiC的力学性能产生巨大差异的主要原因。随着划痕载荷增加,SiC体积分数为45%的SiCp/Al复合材料的去除机制更多取决于以塑性去除为主的基体相,而SiC颗粒则主要表现为脆性去除。

纵扭超声辅助铣削SiCp/Al复合材料表面质量研究

高体积分数SiCp/Al复合材料具有高比强度、高比模数和良好的耐磨性等优异性能。然而,它们的高硬度和脆性会导致精密制造过程中应力分布更为复杂,这会使材料中产生过大的力和过多的热,从而影响加工精度和工件耐久极限寿命。目的通过分析切削过程中颗粒的去除机理和表面缺陷类型,利用纵扭超声辅助铣削(longitudinal-torsional ultrasonic assisted milling,LTUAM)技术,改善高体积分数SiCp/Al复合材料的加工表面质量。方法利用ABAQUS和PYTHON软件,建立考虑颗粒断裂过程的两相随机分布颗粒SiCp/Al复合材料模型,并采用Johnson-Cook模型和Brittle Cracking模型对SiCp/Al复合材料纵扭超声辅助铣削过程进行有限元模拟仿真。针对不同加工参数,进行SiCp/Al复合材料纵扭超声辅助铣削和常规铣削(conventional milling,CM)试验,评估有限元仿真模拟与试验结果的一致性。结果模拟结果表明,损伤和裂纹主要产生在SiC颗粒(SiCp)中上部的切削线上,凹坑缺陷主要产生在颗粒下部的切削线上。试验结果显示,表面缺陷的类型主要包括颗粒的损伤和拔出、颗粒的损伤和断裂形成凹坑、未损伤的颗粒形成凸起、破损颗粒与刀具在已加工表面上挤压摩擦形成犁沟、铝基体涂覆、表面微裂纹和表面空穴等,并且当加工速度120 m/min,超声振幅3μm时,最大裂纹深度最小,表面缺陷最小,表面质量最好。结论对比有限元仿真结果与试验结果发现,二者的表面质量变化趋势基本具有一致性。纵扭超声辅助铣削技术的应用对提高SiCp/Al复合材料的表面质量有较好效果。

Structure of the Intermetallic Compound Ni_3Al Synthesized under Compression of the Powder Mixture of Pure Elements Part Ⅰ: Phase Composition and Microstructure of Main Phase

It was shown by TEM and X-ray analysis that there are four types of grains of the main Ni3Al phase in the structure of the intermetallic obtained by the self-propagation high temperature method (SHS). Every type of grains has its own domain and dislocation structure. There are mono- and polydomains with and without dislocations. The grains of the main phase of monoand polydomains without dislocations and polydomains with dislocations were formed by diffusion in the solid phase. In these conditions NiAl3 phase is located on the grain boundary of the main phase. The Ni2Al3 phase is located at the triple joints of the main phase.

Finite element analysis of temperature and stress fields during selective laser melting process of Al−Mg−Sc−Zr alloy

A 3D finite element model was established to investigate the temperature and stress fields during the selective laser melting process of Al−Mg−Sc−Zr alloy.By considering the powder−solid transformation,temperaturedependent thermal properties,latent heat of phase transformations and molten pool convection,the effects of laser power,point distance and hatch spacing on the temperature distribution,molten pool dimensions and residual stress distribution were investigated.Then,the effects of laser power,point distance and hatch spacing on the microstructure,density and hardness of the alloy were studied by the experimental method.The results show that the molten pool size gradually increases as the laser power increases and the point distance and hatch spacing decrease.The residual stress mainly concentrates in the middle of the first scanning track and the beginning and end of each scanning track.Experimental results demonstrate the accuracy of the model.The density of the samples tends to increase and then decrease with increasing laser power and decreasing point distance and hatch spacing.The optimum process parameters are laser power of 325−375 W,point distance of 80−100μm and hatch spacing of 80μm.

INFLUENCE OF ALLOYING ELEMENTS（Nb，Mo，V） ON MICROSTRUCTURE OF Ti_3Al BASE ALLOYS

The microstructures of Ti-14Al-21Nb and Ti-14Al-20Nb-2Mo-3.2V(wt%) alloys have been investikated by transmission electron microscopy(TEM).The phase constitution and the orientation relationship between α2and βwere identified by means of the selected area diffraction and the micro-diffraction techniques.Results show that,compared to Ti-14Al-21Nb,the alloying elements Mo and V can greatly increase the fraction of β phase and improve significantly the microstructures of Ti-14Al-20Nb-2Mo-3.2V.The ordered B2 structure is also evident in the residual βgrains of the latter alloy.

微量稀土La对Al-7%Si-0.6%Fe合金组织与性能的影响

在Al(铝)-Si(硅)合金中同时添加Sr(锶)和B(硼)存在“中毒”现象,无法同时细化α-Al晶粒和变质共晶Si.本文研究了在同时添加α-Al晶粒细化剂B和共晶Si变质剂Sr的条件下,微量稀土La(镧)对Al-7%Si-0.6%Fe合金组织、热导率和力学性能的影响,分析了稀土La的影响规律及其作用机理.结果表明微量稀土La的添加,一方面可以中和Sr与B的毒化效应,提升共晶Si的变质效果;另一方面可以促使α-Al异质形核基底La B6的形成,并作为表面活性剂降低α-Al的形核过冷度,从而细化α-Al晶粒.共晶Si的变质以及α-Al晶粒的细化有助于同时提升Al-7%Si-0.6%Fe合金的热导率及力学性能.此外,当稀土La的添加量在0.02%—0.06%之间时,合金的导热性能明显提升;随着La添加量的进一步增大,合金热导率下降.

Effects of Additional Elements on Microstructure and Precipitation Behaviour in Rapidly Solidified Al-Ti Base Alloys

Rapidly solidified Al-Ti base alloys were prepared by melt spinning at the cooling rate about 107 K/s. The melt-spun ribbons were used to observe the dricrostructures after heat treatment.In the supersaturated Al-Tl-Si alloy, age hardening occurred after 1 h anneal in the temperature range of 4000~500℃, which seems to be attributed to the precipitation of metastable Ll2- (Al,Si)3Ti phase. However. the microhardness was relatively low because of the low v/o and the insufflcient stability of precipitates. Thus. Cr was added to Al-Ti-Si alloys in order to stabilize the microstructures and to increase the v/o of precipitate5. As a result. the alIoys containing Cr were evaluated to possess the improved properties at the service temperature.

Ductilization of Ni_3Al by Alloying with Substitutional Elements

This paper reviews recent research on ductility improvement of B-undoped Ni_3Al alloys.Ni_3Al binary alloys with hypostoichiometric compositions show appreciable ductility at room temperature when the samples are prepared by recrystallization annealing after cold pressing,although the alloys with stoichiometric and hyperstoichiometric compositions remain brittle.Melt-spun ribbons with hypostoichiometric compositions contain fine anti-phase domains (APDs),while no APD can be seen in melt-spun ribbons with a hyperstoichiometric composition.The ductility in hypostoichiometric Ni_3Al alloys is associated with low ordering energy of the alloys.The addition of ternary elements,which have been classified as γ formers such as Pd,Pt,Cu,Co and Ag.improves ductility of Ni_3Al alloys.Correspondingly,the microstructure of the melt-spun ribbons consists of fine APDs.The addition of γ' formers such as Si,Ti,Zr,V,Nb and Ta leads to brittle intergranular frac- ture.No APD was observed in the melt-spun ribbons of these ternary alloys.

Effect of trace rare earth element Er on high pure Al

The influence of trace Er addition on high pure aluminum was studied by mechanical properties measurement,hardness measurement, optical microscope,transmission electron microscope and energy spectrum analysis. The results show that minor Er in the studied alloy exists in the form of Al 3Er,only a few of Er in α Al based solid solution .Primary Al 3Er particles formed during solidification were often found at the center of aluminum grains and acted as heterogeneous nucleus, also increased the rate of nucleation, therefore the grain are remarkably refined. Trace Er addition to high pure aluminum is able to increase the mechanical properties of high pure Al, which is caused by fine grain strengthening, substructure strengthening and precipitation strengthening. The recrystallization temperature of Er doped aluminum increases above 50 ℃, which is caused by the pinning effect of highly dispersed fine Al 3Er precipitates on dislocations and sub grain boundaries.

EFFECT OF ALLOYING ELEMENT ON MECHANICAL PROPERTIES OF Fe_3 AL AND FeAI ALLOYS

The effect of alloying element such as Mo,Si or B and its stoichoimetric composition on the tensile properties at room and elevated temperatures,and also on the microstructure of Fe_3Al and FeAl alloys has been investigated.Two Fe aluminides were found to be obviously strengthened by all of three elements,but seriously embrittled by Mo and Si.An improvemen over the plasicity of FeAl may be made by adding B,and the fracture surface is variedfrom intergranular to transgranular cleavage type.The room temperature plasticity of the Fe-rich Fe_3Al or Al-rich FeAl is much better than that of the stoichoimetric aluminides.An anoma- lous temperature dependence on the yield strength of Fe_3Al in range of 400 to 500℃ or of FeAl in range of 400 to 500℃ was found.Discussion has been carried out by the aspect of microstructure.

Al-Si镀层22MnB5激光焊的熔池流动特性及元素分布

熔池流动行为对镀层元素在焊缝中的分布起决定性作用.采用建立激光焊熔池三维瞬态数值模型的方法,分析AlSi镀层22MnB5高强度钢激光焊的熔池流动行为及其对焊缝中Al元素分布的影响规律.在焊接试验中,根据能谱仪对焊接接头的扫描数据验证数值模型的可靠性.结合模拟结果与试验结果对激光焊熔池流动行为及焊缝Al元素分布规律进行研究.结果表明,根据激光焊热输入与功率密度阈值的不同,熔池形貌呈现无匙孔、未完全贯穿匙孔和完全贯穿匙孔3种特征,并存有不同的温度场、流场、流速和稳定性.无匙孔熔池由于流速分布均匀,涡流产生较少,稳定性最好.镀层Al元素在焊接接头上下焊趾区域易产生偏聚,较之上表面镀层,下表面镀层进入熔池后Al元素偏聚现象更明显.因此,上部Al元素均质化分布显著优于下部.

Structure of the Intermetallic Compound Ni_3Al Synthesized under Compression of the Powder Mixture of Pure Elements Part Ⅱ: Influence of Alloying by Boron on the Phase Composition and the Microstructure of Grains of the Main Phase

The Ni_3B phase was formed when boron (0.5 at. pct B) was added to the intermetallic of sto- ichiometric and off-stoichiometric (Ni-24 at. pct Al) compounds. In the alloy of stoichiometric composition the particles of Ni_3B phase has the size around 0.1μm and is located on the grain boundary of the main phase. The decreasing of concentrations of Al in the ofF-stoichiometric alloy leads to increase in the degree of the long-range order parameter, increasing the concen- trations of boron in the solid solution and decreasing its localization on the grain boundary. Microalloying of boron leads to increasing in the fraction of grain monodomains with disloca- tions up to 0.7 in the alloy of the off-stoichiometric composition and up to 1 in the alloy of the stoichiometric composition. It was established the correlation between the degree of the concentration inhomogeneity, average density of the dislocations and the average long range-order parameter.

THE EFFECT OF RARE EARTH ELEMENTS ON THE SOLIDIFICATION BEHAVIOR OF Al-Mg ALLOYS

The effect of rare earth element on the solidification behavior of Al-Mg alloy was investigated in a directional solidification apparatus.It was found that during the solidification process.the rare earth element segregated in the liquid at sold-liquid interface,changed the solidification morphology and reduced the secondary arm spacing markedly.

Finite element analysis of stress-strain localization and distribution in Al-4.5Cu-2Mg alloy

Finite element analysis has been carried out to understand the effect of various processing routes and condition on the microscale deformation behavior of Al–4.5 Cu–2 Mg alloy. The alloy has been developed through four different routes and condition, i.e. conventional gravity casting with and without refiner, rheocasting and SIMA process. The optical microstructures of the alloy have been used to develop representative volume elements（RVEs）. Two different boundary conditions have been employed to simulate the deformation behavior of the alloy under uniaxial loading. Finally, the simulated stress-strain behavior of the alloy is compared with the experimental result. It is found that the microstructural morphology has a significant impact on stress and strain distribution and load carrying capacity. The eutectic phase always carries a higher load than the α（Al） phase. The globular α（Al） grains with thinner and uniformly distributed eutectic network provide a better stress and strain distribution. Owing to this, SIMA processed alloy has better stress and strain distribution than other processes. Finally, the simulated yield strength of the alloy is verified by experiment and they have great agreement.

ALE Fractional Step Finite Element Method for Fluid-Structure Nonlinear Interaction Problem

A computational procedure is developed to solve the problems of coupled motion of a structure and a viscous incompressible fluid. In order to incorporate the effect of the moving surface of the structure as well as the free surface motion, the arbitrary Lagrangian-Eulerian formulation is employed as the basis of the finite element spatial discretization. For numerical integration in time, the fraction,step method is used. This method is useful because one can use the same linear interpolation function for both velocity and pressure. The method is applied to the nonlinear interaction of a structure and a tuned liquid damper. All computations are performed with a personal computer.

Influence of chemical composition and alloying elements on microdefects and electron density in Ni-Al alloys

Positron lifetime spectra have been measured in binary Ni Al alloys with different chemical composition and NiAl alloys doped with Cr, Zr, Fe and Mg. The results indicate that in B2 NiAl and Ll 2 Ni 3Al alloys, some of the valance electrons of Ni and Al atoms are localized, which leads to a lower free electron density of the alloy. The mean free electron density of the binary Ni Al alloy decreases with increasing Al content. The open volume of defects on grain boundary of the Ni 3Al is larger than that of monovacancy or dislocation. Structural vacancies and microvoids are found in B2 NiAl alloys with Al content above 45%(mole fraction), and the concentration of the vacancies and open volume of microvoids will increase with higher Al content. The addition of Cr, Zr and Fe into a NiAl alloy can increase its mean free electron density and reduce the open volume of defects on its grain boundary, while with addition of Mg into the NiAl alloy, its mean free electron density decreases and open volume of boundary defects increases.

FINITE ELEMENTS FOR THE LUBRICATED CONTACT BETWEEN SOLIDS IN METAL FORMING REOCESSES

In this paper, the lubrication problem in nmmerical sindation of forming processes is considered.After enumerationg the difficulties encountered when trying to solve such a problem with the finite element method, a generalization of the formaulation of Liu[4-6] for the thin film hydrodynamic lubrication re- gime is presented. This method is then aplied to a strip rolling simulation,using the Arbitrary La- grangian eulerian (ALE) formalism.

Study of rare earth element effect on microstructures and mechanical properties of an Al-Cu-Mg-Si cast alloy

The improvements of microstructures and properties of a high strength aluminum cast alloy were studied. The effects of rare earth elements on the microstructures and mechanical properties of the high strength cast alloy Al-Cu-Mg-Si were investigated. The result shows that the addition of rare earth elements can change the microstructures in refining the grain size of the alloy and making the needle-like and laminar eutectic Si to a granular Si. With the increase of the rare earth, the tensile strength and elongation of the alloy increase first and then fall down. The mechanical properties of the alloy will reach the highest value when the content of rare earth elements is about 0.7%.

Densification simulation of compacted Al powders using multi-particle finite element method

The powder compaction simulations were performed to demonstrate deformation behavior of particles and estimate the effect of different punch speeds and particle diameters on the relative density of powder by a multi-particle finite element model(MPFEM). Individual particle discretized with a finite element mesh allows for a full description of the contact mechanics. In order to verify the reliability of compaction simulation by MPFEM, the compaction tests of porous aluminum with average particle size of 20 μm and 3 μm were performed at different ram speeds of 5, 15, 30 and 60 mm/min by MTS servo-hydraulic tester. The results show that the slow ram speed is of great advantage for powder densification in low compaction force due to sufficient particle rearrangement and compaction force increases with decrease in average particle size of aluminum.

EFFECTS OF TRACE ELEMENTS ON THE OXIDATION OF LOW SEGREGATION Ni－Cr－Al BASED SUPERALLOYS

The oxidation behaviors of two kinds of low segregation Ht-Cr-Al based superalloys have been studied between 1000-1100℃, and compared with that of general Mt-Cr-Al based superalloys. The results indicated that the simultaneous additions of 0.1 wt% S and 0. 1 wt% Zr to low segregation alloys increase the oxidation rate of Al2O3-forming alloy and improve the scale adherence. The addition of 0.1 wt% Zr can ,minimize the negative effects of S on the adherence of Al2O3 scale. Low amounts of S(≤50 ppm wt) have no obviously negative effects on the adherence of Cr2O3 scale formed on one of the low segregation superalloys.