The Effect of Core Eccentricity on the Structural Behavior of Concrete Tall Buildings

The main purpose of this paper is to investigate the effect of core eccentricity on the structural behavior of concrete tall buildings.Concrete buildings of 55 floors with plan dimensions 48.0×48.0 m2 were investigated.Three cases of main core locations are studied:centric(A),eccentric by one sixth(B)and one third(C)of building width.The three-dimensional finite element method has been used in conducting structural analysis through ETABS software.Gravity and lateral(wind and seismic)loadings are applied to all building cases.It has been concluded that the core location is the prime parameter governing the structural behavior of tall buildings.Although the first two cases(A,B)have acceptable and similar structural behaviors conforming to code limits,in the third case(C),the building behavior came beyond code limits.The author introduced remedial action by adding two secondary cores in the opposite direction of the main core(C-R)to restore the building behavior to the code limits.The results of this action were satisfactory.

Structure,Properties and Behavior of Kyanite:Use in Refractory Monolithics

1 Introduction Kyanite is an important naturally occurring in-dustrial mineral and is used in the manufacture of avariety of industrial ceramic products; notable exam-ples include refractories and porcelains. It is a high-pressure polymorph of the aluminosilicates of the ne-sosilicate group, which includes kyanite, sillimanite,and andalusite. These three aluminous or alumina-rich minerals are chemically identical with the compo-sition, Al;SiO;, but have different crystal structuresand physical properties. It is, however, their alumina

Aggregation Behavior and Structure of Associated Polyacrylamide Hydrophobically Modified with 2-Phenoxylethylacrylate

The aggregation behavior and structure of hydrophobically modified block copolymers of acrylamide and 2-phenoxylethylacrylate were investigated by viscometry, 1H NMR relaxation, 2D NOESY, fluorescence and dynamic light scattering. It Was found that the aggregation behavior was strongly dependent on the concentration of polymer solution and the hydrophobe contents. With varying concentration from 2.0, 6.0, 8.0 to 12.0 g/L, there were different aggregate morphologies distributed in aqueous solutions, such as monopolymer chain, micelle-like aggregate, multi-micelle aggregate and cross-linked network. According to the model of aggregation, it can give a reasonable explanation on the large magnitude enhancement of viscosity with the increasing of polymer concentration. Additional data of 2D NOESY and fluorescence show that the copolymer with higher hydrophobe content（molar fraction≥ 1%） is likely to form intra-molecular association.

Full－range nonlinear analysis of fatigue behaviors of reinforced concrete structures by finite element method

The offshore reinforced concrete structures are always subject to cyclic load, such as wave load.In this paper a new finite element analysis model is developed to analyze the stress and strain state of reinforced concrete structures including offshore concrete structures, subject to any number of the cyclic load. On the basis of the anal ysis of the experimental data,this model simplifies the number of cycles-total cyclic strain curve of concrete as three straight line segments,and it is assumed that the stress-strain curves of different cycles in each segment are the same, thus the elastoplastic analysis is only needed for the first cycle of each segment, and the stress or strain corresponding to any number of cycles can be obtained by superposition of stress or strain obtained by the above e lastoplastic analysis based on the cyclic numbers in each segment.This model spends less computer time,and can obtain the stress and strain states of the structures after any number of cycles.The endochronic-damage and ideal offshore concrete platform subject to cyclic loading are experimented and analyzed by the finite element method based on the model proposed in this paper. The results between the experiment and the finite element analysis are in good agreement,which demonstrates the validity and accuracy of the proposed model.

Electronic Structures and Alloying Behaviors of Ferrite Phases in High Co-Ni Secondary Hardened Martensitic Steels

The electronic structure of ferrite (tempered martensite phase) in high Co-Ni secondary hardened martensitic steel has been investigated. The local density of states (LOOS) of alloying elements in the steel displays the relationship between solid solubility and the shape of the LDOS. The bond order integral (BOI) between atoms in the steel shows that the directional bonding of the p orbital of Si or C leads to the brittleness of the steel. At last, ΣBOI between atoms demonstrate that C, Co, Mn, Cr, Mo, Si strengthen the alloyed steel through solid-solution effects.

Editorial: Special subject on the mechanical behavior of thermal protection materials and structures

The thermal protection materials and structures are widely used in hypersonic vehicles for the purpose of thermal insulation, and their mechanical behavior is one of the key issues in design and manufacture of hypersonic vehicles. It is our great pleasure to present the seven papers in this special subject of Theoretical ＆ Applied Mechanics Letters （TAML） and introduce the recent progresses on the mechanical behavior of thermal protection materials and structures by the authors.

Synthesis,Crystal Structure and Magnetic Behavior of a Novel Cd(Ⅱ) Complex with Four Nitroxide Radicals

A novel diamagnetic-metal Cd（Ⅱ） complex with four nitroxide radicals[Cd（IM4Py）4Cl2]（IM4Py=2-（4＇-pyridinyl）-4,4,5,5-tetramethylimidazoline-1-oxyl） was synthesized and characterized by elemental analyses,IR spectra,UV-Vis spectra and X-ray single crystal diffraction.The complex crystallized in triclinic space group P1 with a=0.93285（14） nm,b=1.16827（18） nm,c=1.3660（2） nm,α=112.759（2）°,β=104.524（2）°,γ=92.008（3）°,V= 1.3143（3） nm3,Z=1,Dc=1.335 g/cm3,the final R1=0.0423 and wR2=0.1009.In the title complex,each Cd（Ⅱ） ion adopting a distorted octahedral geometry is coordinated by two Cl-anions and four pyridyl-N atoms from four IM4Py ligands.The magnetic measurements show the weak antiferromagnetic interactions between the nitroxide radicals.

DYNAMIC BEHAVIOR ANALYSIS OF VISCOELASTICALLY DAMPED STRUCTURES

Analysis method for the dynamic behavior of viscoelastically damped structures isstudied.A finite element model of sandwich beams with eight degrees of freedom is set upand the finite element formulation of the equations of motion is given for theviscoelastically damped structures.An iteration method for solving nonlinear eigenvalueproblems is suggested to analyze the dynamic behavior of viscoelastically damped structures.The method has been applied to the complex model analysis of a sandwich cantileverbeam with viscoelastic damping material core.

Memory Behaviors Based on ITO/Graphene Oxide/Al Structure

We investigate the memory properties of the ITO/graphene oxide/Al diodes. It is found that the devices show different memory behaviors with the diverse geometry and thickness of Al. When the thickness of the Al electrode is relatively thick, the device of the cross-point Al electrode shows a three-level memory effect, and the counterpart device of the cross-bar Al electrode exhibits a volatile static random access memory effect. When the thickness of the AI electrode is thinner, the above devices demonstrate a flash memory effect. The different memory behaviors of ITO/GO/AI diodes are ascribed to the mode and degree of reduction and oxidation of GO.

Analysis of the Longitudinal Structure Function F_L from the Non-linear Regge Gluon Density Behavior at Low-x

The longitudinal structure function with shadowing correction according to the nonlinear effects of the gluon density behavior at low x is considered. The solution of the GLR-MQ evolution equation for the gluon density shows that the FL^g（x, Q2） behavior can be tamed by the singularity at low x values. Comparing our results with H1 data at R=4 GeV-1 shows that at very low x this behavior is completely tamed by taking shadowing correction into account.

Impact Analysis of Fluid-structure Coupling Embedded Weapon Bay

The coupling behavior of the imbedded weapon store occurring between the local unsteady flow field round the store and the structure response on the processing of opening its bay-door is simulated by using numerical method based on computational fluid mechanics(CFD).The transient aerodynamic behaviors when opening door under various flight altitudes and the corresponding structure deformation evolution in the unsteady flow fields are analyzed respectively and presented.The rules of aircraft attitude parameters′impacting to the responses of structure and the bay-door′s opening process are obtained by comparing with the analysis results.These rules can be applied to the structure design of bay-door and route specification of missile when disengaged and launched from within store.

Structural first failure times under non-Gaussian stochastic behavior

An analytical moment-based method for calculating structuralfirst failure times under non-Gaussian stochastic behavior is proposed. In the method, a power series that constants can be obtained from response moments （skewness, kurtosis, etc.） is used firstly to map a non-Gaussian structural response into a standard Gaussian process, then mean up-crossing rates, mean clump size and the initial passage probability of a critical barrier level by the original structural response are estimated, and finally, the formula for calculating first failure times is established on the assur^ption that corrected up-crossing rates are independent. An analysis of a nonlinear single-degree-of-freedom dynamical system excited by a Gaussian model of load not only demonstrates the usage of the proposed method but also shows the accuracy and efficiency of the proposed method by comparisons between the present method and other methods such as Monte Carlo simulation and the traditional Gaussian model.

Deformation Behavior and Formability of Gradient Nano-grained AISI 304 Stainless Steel Processed by Ultrasonic Impact Treatment

The deformation behavior and formability of gradient nano-grained（GNG） AISI 304 stainless steel in uniaxial and biaxial states were investigated by means of tensile test and small punch test（SPT）. The GNG top layer was fabricated on coarse grains（CG） AISI 304 by ultrasonic impact treatment. The results showed that the CG substrate could effectively suppress the strain localization of NC in GNG layer, and an approximate linear relationship existed between the thickness of substrate（h） and uniform true strain before necking（ε_（unif））. Grain growth of NC was observed at the stress state with high Stress triaxiality T, which led to better ductility of GNG/CG 304 in SPT, as well as similar true strain after the onset of necking（ε_（neck）） compared with coarse 304 in tensile test. Ei-values of GNG/CG 304 with different structures were nearly the same at different punch speeds, and good formability of GNG/CG 304 was demonstrated. However, punch speed and microstructure needed to be optimized to avoid much lost of membrane strain region in biaxial stress state.

Synthesis and Structure of Butylene Terephthalate-ε-Caprolactone Copolyesters

A series of butylene terephthalate-E-caprolactone copolyesters (BCL) with different hard segment content were successfully synthesized and characterized by 1H-NMR. DSC. PLM and U viscometer, The sequence structure and crystallization characteristics of BCL copolyesters were carefully investigated.

A New Approach to Analyzing Behavioral Change Propagation in Redesigning of Drone Camera Stabilizer

Redesigning of complex products is not an easy task. Engineering change requirements can be extracted at any stage of the product redesign process, and it makes the management of engineering change become a challenging mission. The motivation for this study is to find the shortest path of behavioral change propagation (BCP), minimize the BCP, access to the special behavioral elements in order to better managing the BCP and classifying the behavioral attribute of the elements in terms of their relationship to change by betweenness centrality coefficient (BNCC), clustering coefficient (CLC), reachability coefficient (RC) and change propagation index (CPI). In this article, the procedure of managerial decision-making is proposed by combining system restrictions in behavioral clustering design structure matrix (BCDSM) with optimization algorithms. The practicality of suggested method is verified in redesign procedure of a phantom drone camera stabilizer as a case study. The results, indicate that the absorption of change by behavioral elements is dominant in the mechanical (63.9%), electrical (61.1%) and thermal (38.9%) behaviors of the drone camera stabilizer system in redesign process. These elements are best candidates for reducing the cost and time of behavioral changes in the system redesign and are desirable for the designer.

HYDROPHOBICALLY ASSOCIATING POLYACRYLAMIDES MODIFIED BY A NOVEL SELF-ASSOCIATIVE CATIONIC MONOMER

A series of hydrophobically associating polyacrylamides modified by small amounts （〈 3 mol%） of a self- associative cationic monomer 4-（2-（acryloyloxy） ethoxy） benzyl tri-ethyl ammonium bromide （AEBA） as hydrophobe were synthesized by radical copolymerization in aqueous solutions without external surfactants. The resulting eopolymers containing a multiblock structure exhibited a high tendency for hydrophobic association and a high thickening capacity. Solution properties and aggregation structures were investigated by viscometry and fluorescence technique. The high viscosity enhancement was found as the polymer concentration beyond a critical value c＊ and strongly depended on the copolymer microstructures. The number and length of hydrophobic microblocks within the copolymer backbones could be controlled by changing the AEBA concentration in copolymerization system. Addition of salt induced more hydrophobic association and viscosity enhancement. The synthesis method used was simple and environmentally friendly without any external surfactant contamination in comparison with the conventional micellar copolymerization.

Corrosion Behavior of Mg-Zn-Y Alloy with Long-period Stacking Ordered Structures

Mg-Zn-Y alloys with long-period stacking ordered structures were prepared by an ingot casting method. The corrosion performance of Mg-Zn-Y alloys was studied by combining gas-collecting test, immersion test and electrochemical measurements in order to determine the corrosion rate and mechanism of the alloys. The results showed that the volume fraction of Mg（12）YZn phase increased and the shape of the Mg（12）YZn phase changed from discontinuous to continuous net-like with increasing Zn and Y content. The corrosion rate of the alloys greatly depended on the distribution and volume fraction of the Mg（12）YZn phase. Corrosion products appeared at the junction of Mg phase and Mg（12）YZn phase, indicating that the Mg（12）YZn phase accelerated galvanic corrosion of Mg matrix. Mg（97）Zn1Y2 alloy shows the lowest corrosion rate due to the continuous distribution of Mg（12）YZn phase.

Electronic structure and catalytic behavior of tungsten carbides

The electronic structure of tungsten carbide was investigated by EHMO semiempirical me- thod.The most stable structure of the carbide was predicted on the basis of binding energy calcula- tions.The W-C bonding is covalent in nature with some charge transfer from the W to the C atoms. The increase in the occupancy of the d shell of the W atoms and the position of the Fermi level may account for the platinum-like catalytic behavior of tungsten carbide.

Solids behavior in dilute zone of a CFB riser under turbulent conditions

The behavior of the solid phase in the upper zone of a circulating fluidized bed riser was studied using a phase Doppler anemometer. Glass particles of mean diameter 107μm and superficial gas velocities UE covering the turbulent and the beginning of the fast fluidization regime were investigated. Three static bed heights were tested. Ascending and descending particles were found co-existing under all oper ating conditions tested, and at all measurement locations. Superficial gas velocity proved/happened to have a larger effect on descending particles at the wall and on ascending particles in the central region. Transversal particle velocities in both directions （toward the center and toward the wall） behaved rela- tively equivalently, with only slight difference observed at the wall. However, observation of the number of particles moving in either transversal direction showed a change in bed structure when increasing Ug. Furthermore, a balance was constantly observed between the core zone and the annulus zone where the mutual mass transfer between these two zones occurred continuously. Transition from a slow to a fast particle motion was accompanied by a transition to high levels of velocity fluctuations, and was found corresponding to the appearance of significant solid particle flow rate.

Serration and Noise Behavior in Advanced Materials

The Chinese Materials Research Society（C-MRS）Conference（2015）was held in the Guizhou Park Hotel International Conference Center,Guiyang,China,from July 10-14,2015.This conference consists of 30symposia,including 4international symposia.As one of 4international symposia,＂Serration and noise behavior in advanced materials＂