The emulsion polymerization of N-phenylmaleimide, Styrene and acrylonitrile was studied. The thermal property of this copolymer was measures by dynamic thermomechanical analysis(DMA). The mechanical properties, such a...The emulsion polymerization of N-phenylmaleimide, Styrene and acrylonitrile was studied. The thermal property of this copolymer was measures by dynamic thermomechanical analysis(DMA). The mechanical properties, such as tensile strength, hardness and fie-cural Strength were StUdied experimentally. The results indicated that not only the monomer component but also the polymerization technologies have effect on the properties of the copolymer. The optimum monomer content and suitable polymerization method were obtained.展开更多
Emulsion copolymerization of styrene and ethylene catalyzed by a series of neutral nickel(Ⅱ) complexes was carried out in an aqueous system to give high-molecular-weight copolymers.The copolymers and emulsions were c...Emulsion copolymerization of styrene and ethylene catalyzed by a series of neutral nickel(Ⅱ) complexes was carried out in an aqueous system to give high-molecular-weight copolymers.The copolymers and emulsions were characterized by an array of techniques including NMR,GPC,TEM,WAXD and DSC.The results indicate that the copolymers obtained are mostly block copolymers of polyethylene with random insertion of styrene units,and their M_W is in the range of 10~5-10~6.By enhancing the electron withdrawing of the s...展开更多
Radiation induced grafting of viscose rayon fabrics, consisting mainly of cellulose fibers, with some acrylic acid derivatives, namely methyl acrylate, acrylamide and acrylonitrile, and also styrene, has been studied....Radiation induced grafting of viscose rayon fabrics, consisting mainly of cellulose fibers, with some acrylic acid derivatives, namely methyl acrylate, acrylamide and acrylonitrile, and also styrene, has been studied. The resultant graft yields have been determined as a function of the applied different experimental parameters. The impact of the graft yields on the physicochemical properties of viscose rayon fabrics such as swelling, moisture absorption, tensile strength, elongation at break, crease recovery angle and also dyeing ability of the grafted fabrics, has been also studied.展开更多
High-density polyethylene (HDPE) films were irradiated by 60Co gamma ray with a dose of 100 kGy in air and then immersed in aqueous solution of acrylic acid (AA) and sodium styrene sulfonate (SSS) at different tempera...High-density polyethylene (HDPE) films were irradiated by 60Co gamma ray with a dose of 100 kGy in air and then immersed in aqueous solution of acrylic acid (AA) and sodium styrene sulfonate (SSS) at different temperature. The effects of grafting conditions such as temperature, reaction time, Mohr’s salt concentration, and total concentration of monomer on grafting yield were studied. Both grafting yield of AA and SSS onto HDPE respectively increases with total concentration of monomers. The highest grafting yield was observed at 3 mol/L monomers where the grafted PE swelled to the largest extent in the monomers mixture. The grafting yield increases with reaction time and then levels off. At higher temperature, the grafting yield decreases with Mohr’s salt concentration, but increases at low temperature when Mohr’s salt concentration is 0.083%. Which can be interpreted that in the presence of Fe2+ diperoxides and hydroperoxides may decompose at low temperature to form radical which can initiate the grafting. The physical and chemical properties of grafting films were also investigated.展开更多
Grafting copolymerization of styrene and acrylic acid onto polypropylene fabric had been studied by using a pre-irradiation technique. The polypropylene fabric Samples were irradiated by Y-ray and electron beam under ...Grafting copolymerization of styrene and acrylic acid onto polypropylene fabric had been studied by using a pre-irradiation technique. The polypropylene fabric Samples were irradiated by Y-ray and electron beam under the conditions of air and nitrogen gas, respectively. The effect of absorbed dose, monomer concentration in solvent, reaction temperature and reaction time on the degree of grafting were determined. The effects of metallic salts and sulphuric acid on the grafting yield of acrylic acid were also examined. The samples irradiated by electron beam give a much higher degree of grafting than those by Y -ray when styrene was grafted to polypropylene fabric. However, the grafting yield of acrylic acid on polypropylene fabric in the presence of metallic salts and sultric acid showed the opposite results from the case of styrene. This effect is reasonably interpreted by assuming that the grafting is dominated by trapped radicals and peroxides in pre-irradiated polypropylene.展开更多
Photoinitiated inverse emulsion polymerization of sodium acrylate(AANa)in kerosene was carried out at room orlower temperature,using 2,2-dimethoxy-2-phenylacetophenone(DMPA)as the initiator.Kinetic investigations indi...Photoinitiated inverse emulsion polymerization of sodium acrylate(AANa)in kerosene was carried out at room orlower temperature,using 2,2-dimethoxy-2-phenylacetophenone(DMPA)as the initiator.Kinetic investigations indicated thatthe polymerization could be completed in about 30 min and produce polymer with high molecular weight(10~6~10~7).It wasfound that monomer droplets are the main sites for the polymerization(nucleation).With the increase of DMPAconcentration,polymerization rate(R_p)reaches a maximum value while molecular weight of the produced polymer has anadverse result,but the dependence of R_p on incident light intensity is similar.Influences of other parameters such asmonomer concentration,emulsifier content and reaction temperature,etc.were also studied.At lower pH values of waterphase,R_p depends strongly on the pH due to the electrostatic interaction between the ionized radicals and the monomer.Athigher pH,R_p shows a slight dependence on pH.展开更多
Styrene-acrylate latex with high glass transition temperature (T), low minimum film forming temperature(MFT) and good stability was prepared via core-shell emulsion polymerization. With semicontinuous process, hig...Styrene-acrylate latex with high glass transition temperature (T), low minimum film forming temperature(MFT) and good stability was prepared via core-shell emulsion polymerization. With semicontinuous process, high conversion rate of monomer and low gel rate were achieved. The weight ratio of core monomer to shell monomer was approximately 1.35. It is found that many factors such as emulsifiers, initiators, reaction temperature, pH value and polymerization technology have influences on the permormance of styrene-acrylate latex. The prepared latex was characterized by TEM and FTIR. The obtained latex with T of 20.57 ℃, MFT or5.0 ℃, and good stability, had good stability of film forming.展开更多
Stable high-solids-content acrylate emulsion were obtained with a nonionic polymerizable emulsifier allyloxy nonylphenoxy poly (ethyleneoxy) (10) ether (ANPEO10), and a conventional emulsifier OP-10 as a referen...Stable high-solids-content acrylate emulsion were obtained with a nonionic polymerizable emulsifier allyloxy nonylphenoxy poly (ethyleneoxy) (10) ether (ANPEO10), and a conventional emulsifier OP-10 as a reference sample. 1H NMR proves that the polymerizable emulsifier ANPEO10 has been incorporated into the resulted acrylate polymers. TEM demonstrates that there are some differences in the particle morphologies. AFM proves that the polymerizable emulsifier ANPEO10 migrating to the surface of the emulsion film was much less than the conventional emulsifier OP-10. The polymerizable emulsifier ANPEO10 can enhance the adhesion with glass plate compared to the conventional emulsifier. Furthermore, with increasing amount of emulsifier, the surface free energy of the films first decreased and then increased, and the adhesion with glass plate is initially enhanced and then attenuated. The water-resistance and solvent-resistance of the films prepared by the polymerizable emulsifier ANPEO10 are superior to those prepared by the conventional emulsifier OP-10.展开更多
The seeded semicontinuous emulsion multi-copolymerization of butyl acrylate (BA), 2-ethylhexyl acrylate (2EHA), methyl methacrylate (MMA), 2-hydroxyl propyl acrylate (HOPA) and acrylic acid (AA) was used to prepare th...The seeded semicontinuous emulsion multi-copolymerization of butyl acrylate (BA), 2-ethylhexyl acrylate (2EHA), methyl methacrylate (MMA), 2-hydroxyl propyl acrylate (HOPA) and acrylic acid (AA) was used to prepare the acrylic latexes with high-solid content. The effects of monomer emulsion feed rates (R(a)) and (R/E)(E) values, the ratio of emulsifier amount between the initial charge (R) and the addition monomer emulsion (E), on the polymerization reaction features, the viscosities, surface tensions,particle sizes and particle sizes distributions of latexes, T-g and the insoluble fractions of films, the 180 degrees peel strength, tack and holding power of pressure-sensitive adhesive (PSA) tapes, prepared from the latexes, were studied. Experimental study shows that the grafting and crosslinking fraction in the PSA tapes must be controlled within a suitable range to keep the balance of the 180 degrees peel strength, tack and holding power.展开更多
Introduction The emulsion of acrylate copolymers with actively functional groups have been widely developed and used as coating, adhesive and handling agent in spinning and weaving industry. Bessett, D. R. et al. stud...Introduction The emulsion of acrylate copolymers with actively functional groups have been widely developed and used as coating, adhesive and handling agent in spinning and weaving industry. Bessett, D. R. et al. studied the thermoset of N-(isobutoxymethyl) acrylamide by thermal evolution analysis and thermal gas chromatogram. Krejcar,展开更多
The formation mechanism of monodisperse polymer latex particles in the emulsifier-free emulsion polymerizationof methyl methacrylate and butyl acrylate with potassium persulfate as initiator was investigated. A multi-...The formation mechanism of monodisperse polymer latex particles in the emulsifier-free emulsion polymerizationof methyl methacrylate and butyl acrylate with potassium persulfate as initiator was investigated. A multi-step formationmechanism for the monodisperse polymer particles was proposed. The nucleation mechanism is considered to be thecoagulation of the precursor particles by homogeneous nucleation when the primary particles reach a critical size with highsurface charge density and sufficient stability. It had been proved by a special experiment that the early latex particles formedby the coagulation were stable. The primary particles grow by absorbing monomers and radicals in the polymerization systemand then become colloidally unstable again due to the understandable decrease of particle surface charge density, which leadsto the aggregation of the growing particles and the formation of larger latex pedicles therefrom. Aner the nucleation period,the preferential aggregation of the smaller particles in the propagation process leads to the change of the particles towards auniform size and narrower particle size distribution. The coexistence and competition of homogeneous nucleation,coagulation, propagation and aggregation result in the increase of the polydispersity index (U = D_(43)/D_(10)) in the first Stage,then its decrease in the later stage because of the competition of propagation and aggregation, and the gradual formation ofthe monodisperse particles.展开更多
Using butyl acrylate(BA),methyl methacrylate(MMA),methacrylic acid(MAA) and mixed emulsifier as raw materials,the self-crosslinked emulsion was prepared via pre-emulsified and semi-continuous seeded emulsion polymeriz...Using butyl acrylate(BA),methyl methacrylate(MMA),methacrylic acid(MAA) and mixed emulsifier as raw materials,the self-crosslinked emulsion was prepared via pre-emulsified and semi-continuous seeded emulsion polymerization technology in the presence of N-hydroxymethyl acrylamide and poly solidum maleate. The influence of mass ratio of BA to MMA,amount of N-hydroxymethyl acrylamide and poly solidum maleate on the rheological properties of the self-crosslinked emulsion was studied. Possible cross-linked mechanism of self-crosslinked monomer was investigated. And the relationship between emulsion viscosity and shear rate was investigated. The results show that the self-crosslinked acrylate emulsion with high elasticity can be synthesized when the mass fractions of BA is 60%,MMA is 40%,and added amount of N-hydroxymethyl acrylamide is 2.5%-3.0% and added amount of poly solidum maleate is 0.3%-0.4%. The self-crosslinkage process of N-hydroxymethyl acrylamide involves two steps. One is copolymerization of N-hydroxymethyl acrylamide and acrylate,the other is cross-linkage among polymer molecules via condensation reaction of methylol. The emulsion is of rheological properties of pseudo-plastic fluid and belongs to non-Newtonian fluid.展开更多
Electrospun nanofibers present a new and rapidly growing research area due to their pronounced micro and nano characteristics associated with high surface area to volume ratio. Poly(styrene-co-acrylamide) and polystyr...Electrospun nanofibers present a new and rapidly growing research area due to their pronounced micro and nano characteristics associated with high surface area to volume ratio. Poly(styrene-co-acrylamide) and polystyrene polymers were synthesized by boiling temperature soap free emulsion polymerization in aqueous medium with potassium peroxosulphate as the initiator. The resulting polymers were dissolved in dimethylformamide and teterahydrofuran (DMF: THF) (4:1) to form polymer solutions that were electrospun into fiber mats with diameters ranging from 1.84 - 2.53 μm and 5.01 μm, respectively. The fibers were characterized by Fourier transform infrared spectroscopy (FTIR) equipped with universal ATR sampling accessory (4000 - 400 cm-1). The morphology and size were examined by a scanning electron miscroscope (SEM) and the thermal properties by thermogravimetric analysis (TGA). The FTIR spectra of the poly(styrene-co-acrylamide) revealed the presence of acrylamide on the polystyrene chain. Thus, surface modification of polystyrene with acrylamide is possible in a single step polymerization reaction prior to electrospinning.展开更多
A novel surface modifying agent and internal compatilizer of inorganic and macromolecule composite materials,P(St/MAH/BA)terpolymer,was synthesized in butanone by solution polymerization method using styrene(St),malei...A novel surface modifying agent and internal compatilizer of inorganic and macromolecule composite materials,P(St/MAH/BA)terpolymer,was synthesized in butanone by solution polymerization method using styrene(St),maleic anhydride(MAH),and butyl acrylate(BA)as monomers and azobisisobutyronitrile(AIBN)as an initiator.Some affecting factors on terpolymers yields such as polymerization time,reaction temperature,solvent volume,initiator content,and reactants ratios were studied.Furthermore,the structure and thermal properties of terpolymers were primarily characterized and determined by Fourier Transform Infrared Spectroscopy(FTIR),nuclear magnetic resonance(NMR),thermogravimetric analysis(TGA),and gel permeation chromatography(GPC).The results indicate that the terpolymers are random polymers and the yields are low,but the thermal decomposed temperature of terpolymers P(St/MAH/BA)is around 220 ℃ and the average molecular weights(Mw)achieve 1.189×105 g·mol-1.展开更多
A silicone acrylate micro-emulsion of multipolymer was prepared by seed emulsion polymerization. The effects of polymerization process, emulsifier rate and amount, initiator rate and amount, polymerization temperature...A silicone acrylate micro-emulsion of multipolymer was prepared by seed emulsion polymerization. The effects of polymerization process, emulsifier rate and amount, initiator rate and amount, polymerization temperature, functional monomers, titration time on performances of emulsion have been discussed in detail.展开更多
In this study, P(St-MAA) seed latex particles were first prepared via soap-free emulsion polymerization of styrene (St) and methacrylic acid (MAA), then the seed particles were allowed to swell with St at room t...In this study, P(St-MAA) seed latex particles were first prepared via soap-free emulsion polymerization of styrene (St) and methacrylic acid (MAA), then the seed particles were allowed to swell with St at room temperature, and the P(St-MAA)/P(St- NaSS) core/shell latex particles were then synthesized via seeded emulsion copolymerization of St and sodium styrene sulphonate (NaSS) using AIBN as initiator in the presence of N,N^-methylenebisacrylamide (BAA, water-soluble crosslinker). Results showed that the polymerization could be carried out smoothly when the ratio of BAA to total monomers was less than 3 mol%, the narrow dispersed P(St-MAA) seed particles with the diameter of 150 nm and the P(St-MAA)/P(St-NaSS) core/shell latexes with the particle size of about 200 nm were synthesized. When the 25/75 mole ratio of NaSS/(St + MAA) and 2 tool% of BAA were used in the seeded emulsion polymerization, the resulted P(St-MAA)/P(St-NaSS) latex product showed a low weight loss after water extraction, and the NaSS unit content in the whole particle and in the shell reached 11.7 mol% and 34.6 mol%, resoectivelv.展开更多
Despite the great potential of cellulose wood pulp and cellulose nanofibrils as reinforcing filler in thermoplastics,its use is limited due to its tendency to form agglomerates and due to its high hydrophilic characte...Despite the great potential of cellulose wood pulp and cellulose nanofibrils as reinforcing filler in thermoplastics,its use is limited due to its tendency to form agglomerates and due to its high hydrophilic character.Here we describe fiberboard composites with high contents of wood pulp or cellulose nanofibrils,and a resin of poly(styrene-methyl-methacrylate-acrylic acid)used as water-based emulsion.Cellulose wood pulp and cellulose nanofibrils were used directly in the form of water suspensions.The method is based on the flocculation of the polymer emulsion followed by agglomeration of a mixture of the polymer emulsion and cellulose suspension,leading to the co-precipitation of the composite material,which can be easily separated from the water phase.Composites with acrylic polymer/cellulose fibers in the proportions of 75:25,50:50 and 25:75 wt%were prepared.Composites were characterized by scanning electron microscopy(SEM),Fourier transform infrared spectroscopy(FTIR),thermogravimetric analysis(TGA),dynamic mechanical analysis(DMA)and water absorption tests.SEM analysis revealed a very good dispersion of the fibers without evidence of agglomeration,which led to superior mechanical properties.These results showed the effectiveness of the methodology and the potential of cellulose wood pulp and CNF as reinforcement fillers in fiberboard composites and any other high fiber-content materials.展开更多
Surface sizing is an effective way to increase paper’s water-resistance and printability.The purpose of this study was to study synthesis process to develop an efficient cationic styrene-acrylic acid ester emulsion(S...Surface sizing is an effective way to increase paper’s water-resistance and printability.The purpose of this study was to study synthesis process to develop an efficient cationic styrene-acrylic acid ester emulsion(SAE)for the surface sizing of paper.Dimethylaminoethyl methacrylate methyl chloride(DMC)was used as the cationic monomer,and cationic starch or native starch was used as the emulsion stabilizer to copolymerize with styrene and butyl acrylate.The results indicated that the SAE synthesized with cationic starch and DMC had a high cationic charge density and a high DMC conversion rate.Paper sized with the cationic SAE had higher surface strength and lower Cobb value than the paper sized with other surface sizing agents such as,anionic SAE,and cationic or oxidized starch.Scanning electron micrographs revealed that the paper sized with a combination of oxidized starch and cationic SAE had smoother surface morphology when compared to the paper sized with oxidized starch alone,or with oxidized starch and anionic SAE.展开更多
Stable poly(styrene-co-sodium styrene sulfonate) (P(St-NaSS) nanoparticles with broader size distribution were synthesized by thermal emulsion polymerization without any conventional initiators and emulsifiers. T...Stable poly(styrene-co-sodium styrene sulfonate) (P(St-NaSS) nanoparticles with broader size distribution were synthesized by thermal emulsion polymerization without any conventional initiators and emulsifiers. The obtained polymer nanoparticles have higher potential, and the particle sizes have broad distribution. The stability of polymer particles originated from the addition of small amounts of ionic comonomer, NaSS, which can act as an emulsifier in somewhat. The monomer conversion could reach up to about 28 wt% in 48 h, and did not increase by further polymerization when higher polymerization temperature (120℃) was employed. This polymerization system may be give some further understand for mechanism of emulsion polymerization.展开更多
Well-defined nonionic hydrophilic ω-acryloyl poly(ethylene oxide) macro-monomer (PEO-A) has been prepared by living anionic polymerization of ethylene oxidewith diphenyl methyl potassium as the initiator and acryloyl...Well-defined nonionic hydrophilic ω-acryloyl poly(ethylene oxide) macro-monomer (PEO-A) has been prepared by living anionic polymerization of ethylene oxidewith diphenyl methyl potassium as the initiator and acryloyl chloride as the reaction termi-nating agent. The polymer was characterized by FTIR and SEC. The emulsifier-free emul-sion polymerization of methyl methacrylate (MMA) and n-butyl acrylate (BA) containingvarious concentrations of PEO-A was studied. In all cases stable emulsion coplymerizationsof MMA and BA were obtained. The stabilizing effect was found to be dependent on themolecular weight and the feed amount of the macromonomer.展开更多
文摘The emulsion polymerization of N-phenylmaleimide, Styrene and acrylonitrile was studied. The thermal property of this copolymer was measures by dynamic thermomechanical analysis(DMA). The mechanical properties, such as tensile strength, hardness and fie-cural Strength were StUdied experimentally. The results indicated that not only the monomer component but also the polymerization technologies have effect on the properties of the copolymer. The optimum monomer content and suitable polymerization method were obtained.
文摘Emulsion copolymerization of styrene and ethylene catalyzed by a series of neutral nickel(Ⅱ) complexes was carried out in an aqueous system to give high-molecular-weight copolymers.The copolymers and emulsions were characterized by an array of techniques including NMR,GPC,TEM,WAXD and DSC.The results indicate that the copolymers obtained are mostly block copolymers of polyethylene with random insertion of styrene units,and their M_W is in the range of 10~5-10~6.By enhancing the electron withdrawing of the s...
文摘Radiation induced grafting of viscose rayon fabrics, consisting mainly of cellulose fibers, with some acrylic acid derivatives, namely methyl acrylate, acrylamide and acrylonitrile, and also styrene, has been studied. The resultant graft yields have been determined as a function of the applied different experimental parameters. The impact of the graft yields on the physicochemical properties of viscose rayon fabrics such as swelling, moisture absorption, tensile strength, elongation at break, crease recovery angle and also dyeing ability of the grafted fabrics, has been also studied.
文摘High-density polyethylene (HDPE) films were irradiated by 60Co gamma ray with a dose of 100 kGy in air and then immersed in aqueous solution of acrylic acid (AA) and sodium styrene sulfonate (SSS) at different temperature. The effects of grafting conditions such as temperature, reaction time, Mohr’s salt concentration, and total concentration of monomer on grafting yield were studied. Both grafting yield of AA and SSS onto HDPE respectively increases with total concentration of monomers. The highest grafting yield was observed at 3 mol/L monomers where the grafted PE swelled to the largest extent in the monomers mixture. The grafting yield increases with reaction time and then levels off. At higher temperature, the grafting yield decreases with Mohr’s salt concentration, but increases at low temperature when Mohr’s salt concentration is 0.083%. Which can be interpreted that in the presence of Fe2+ diperoxides and hydroperoxides may decompose at low temperature to form radical which can initiate the grafting. The physical and chemical properties of grafting films were also investigated.
基金the National Natural Science Foundation of China (29404031 ) and the Korea Science and Technology Foundation
文摘Grafting copolymerization of styrene and acrylic acid onto polypropylene fabric had been studied by using a pre-irradiation technique. The polypropylene fabric Samples were irradiated by Y-ray and electron beam under the conditions of air and nitrogen gas, respectively. The effect of absorbed dose, monomer concentration in solvent, reaction temperature and reaction time on the degree of grafting were determined. The effects of metallic salts and sulphuric acid on the grafting yield of acrylic acid were also examined. The samples irradiated by electron beam give a much higher degree of grafting than those by Y -ray when styrene was grafted to polypropylene fabric. However, the grafting yield of acrylic acid on polypropylene fabric in the presence of metallic salts and sultric acid showed the opposite results from the case of styrene. This effect is reasonably interpreted by assuming that the grafting is dominated by trapped radicals and peroxides in pre-irradiated polypropylene.
基金This work was supported by the Scientific Research Foundation for Youth(No.QN0404).
文摘Photoinitiated inverse emulsion polymerization of sodium acrylate(AANa)in kerosene was carried out at room orlower temperature,using 2,2-dimethoxy-2-phenylacetophenone(DMPA)as the initiator.Kinetic investigations indicated thatthe polymerization could be completed in about 30 min and produce polymer with high molecular weight(10~6~10~7).It wasfound that monomer droplets are the main sites for the polymerization(nucleation).With the increase of DMPAconcentration,polymerization rate(R_p)reaches a maximum value while molecular weight of the produced polymer has anadverse result,but the dependence of R_p on incident light intensity is similar.Influences of other parameters such asmonomer concentration,emulsifier content and reaction temperature,etc.were also studied.At lower pH values of waterphase,R_p depends strongly on the pH due to the electrostatic interaction between the ionized radicals and the monomer.Athigher pH,R_p shows a slight dependence on pH.
文摘Styrene-acrylate latex with high glass transition temperature (T), low minimum film forming temperature(MFT) and good stability was prepared via core-shell emulsion polymerization. With semicontinuous process, high conversion rate of monomer and low gel rate were achieved. The weight ratio of core monomer to shell monomer was approximately 1.35. It is found that many factors such as emulsifiers, initiators, reaction temperature, pH value and polymerization technology have influences on the permormance of styrene-acrylate latex. The prepared latex was characterized by TEM and FTIR. The obtained latex with T of 20.57 ℃, MFT or5.0 ℃, and good stability, had good stability of film forming.
基金Funded by Ministry of Education (No.2006-KL-008),and Qingxin Hanerchem Chemical Technology Co,Ltd.
文摘Stable high-solids-content acrylate emulsion were obtained with a nonionic polymerizable emulsifier allyloxy nonylphenoxy poly (ethyleneoxy) (10) ether (ANPEO10), and a conventional emulsifier OP-10 as a reference sample. 1H NMR proves that the polymerizable emulsifier ANPEO10 has been incorporated into the resulted acrylate polymers. TEM demonstrates that there are some differences in the particle morphologies. AFM proves that the polymerizable emulsifier ANPEO10 migrating to the surface of the emulsion film was much less than the conventional emulsifier OP-10. The polymerizable emulsifier ANPEO10 can enhance the adhesion with glass plate compared to the conventional emulsifier. Furthermore, with increasing amount of emulsifier, the surface free energy of the films first decreased and then increased, and the adhesion with glass plate is initially enhanced and then attenuated. The water-resistance and solvent-resistance of the films prepared by the polymerizable emulsifier ANPEO10 are superior to those prepared by the conventional emulsifier OP-10.
基金This work was supported by the National Natural Science Foundation of China
文摘The seeded semicontinuous emulsion multi-copolymerization of butyl acrylate (BA), 2-ethylhexyl acrylate (2EHA), methyl methacrylate (MMA), 2-hydroxyl propyl acrylate (HOPA) and acrylic acid (AA) was used to prepare the acrylic latexes with high-solid content. The effects of monomer emulsion feed rates (R(a)) and (R/E)(E) values, the ratio of emulsifier amount between the initial charge (R) and the addition monomer emulsion (E), on the polymerization reaction features, the viscosities, surface tensions,particle sizes and particle sizes distributions of latexes, T-g and the insoluble fractions of films, the 180 degrees peel strength, tack and holding power of pressure-sensitive adhesive (PSA) tapes, prepared from the latexes, were studied. Experimental study shows that the grafting and crosslinking fraction in the PSA tapes must be controlled within a suitable range to keep the balance of the 180 degrees peel strength, tack and holding power.
文摘Introduction The emulsion of acrylate copolymers with actively functional groups have been widely developed and used as coating, adhesive and handling agent in spinning and weaving industry. Bessett, D. R. et al. studied the thermoset of N-(isobutoxymethyl) acrylamide by thermal evolution analysis and thermal gas chromatogram. Krejcar,
文摘The formation mechanism of monodisperse polymer latex particles in the emulsifier-free emulsion polymerizationof methyl methacrylate and butyl acrylate with potassium persulfate as initiator was investigated. A multi-step formationmechanism for the monodisperse polymer particles was proposed. The nucleation mechanism is considered to be thecoagulation of the precursor particles by homogeneous nucleation when the primary particles reach a critical size with highsurface charge density and sufficient stability. It had been proved by a special experiment that the early latex particles formedby the coagulation were stable. The primary particles grow by absorbing monomers and radicals in the polymerization systemand then become colloidally unstable again due to the understandable decrease of particle surface charge density, which leadsto the aggregation of the growing particles and the formation of larger latex pedicles therefrom. Aner the nucleation period,the preferential aggregation of the smaller particles in the propagation process leads to the change of the particles towards auniform size and narrower particle size distribution. The coexistence and competition of homogeneous nucleation,coagulation, propagation and aggregation result in the increase of the polydispersity index (U = D_(43)/D_(10)) in the first Stage,then its decrease in the later stage because of the competition of propagation and aggregation, and the gradual formation ofthe monodisperse particles.
基金Project(2003B10506) supported by Guangdong Provincial Department of Science and Technology, China
文摘Using butyl acrylate(BA),methyl methacrylate(MMA),methacrylic acid(MAA) and mixed emulsifier as raw materials,the self-crosslinked emulsion was prepared via pre-emulsified and semi-continuous seeded emulsion polymerization technology in the presence of N-hydroxymethyl acrylamide and poly solidum maleate. The influence of mass ratio of BA to MMA,amount of N-hydroxymethyl acrylamide and poly solidum maleate on the rheological properties of the self-crosslinked emulsion was studied. Possible cross-linked mechanism of self-crosslinked monomer was investigated. And the relationship between emulsion viscosity and shear rate was investigated. The results show that the self-crosslinked acrylate emulsion with high elasticity can be synthesized when the mass fractions of BA is 60%,MMA is 40%,and added amount of N-hydroxymethyl acrylamide is 2.5%-3.0% and added amount of poly solidum maleate is 0.3%-0.4%. The self-crosslinkage process of N-hydroxymethyl acrylamide involves two steps. One is copolymerization of N-hydroxymethyl acrylamide and acrylate,the other is cross-linkage among polymer molecules via condensation reaction of methylol. The emulsion is of rheological properties of pseudo-plastic fluid and belongs to non-Newtonian fluid.
文摘Electrospun nanofibers present a new and rapidly growing research area due to their pronounced micro and nano characteristics associated with high surface area to volume ratio. Poly(styrene-co-acrylamide) and polystyrene polymers were synthesized by boiling temperature soap free emulsion polymerization in aqueous medium with potassium peroxosulphate as the initiator. The resulting polymers were dissolved in dimethylformamide and teterahydrofuran (DMF: THF) (4:1) to form polymer solutions that were electrospun into fiber mats with diameters ranging from 1.84 - 2.53 μm and 5.01 μm, respectively. The fibers were characterized by Fourier transform infrared spectroscopy (FTIR) equipped with universal ATR sampling accessory (4000 - 400 cm-1). The morphology and size were examined by a scanning electron miscroscope (SEM) and the thermal properties by thermogravimetric analysis (TGA). The FTIR spectra of the poly(styrene-co-acrylamide) revealed the presence of acrylamide on the polystyrene chain. Thus, surface modification of polystyrene with acrylamide is possible in a single step polymerization reaction prior to electrospinning.
基金Nano Project Foundation of Shanghai Technology Committee,China(No.0652nm039)Shanghai Leading Academic Discipline Project,China(No.B502)Shanghai Key Laboratory Proejct,China(No.08DZ2230500)
文摘A novel surface modifying agent and internal compatilizer of inorganic and macromolecule composite materials,P(St/MAH/BA)terpolymer,was synthesized in butanone by solution polymerization method using styrene(St),maleic anhydride(MAH),and butyl acrylate(BA)as monomers and azobisisobutyronitrile(AIBN)as an initiator.Some affecting factors on terpolymers yields such as polymerization time,reaction temperature,solvent volume,initiator content,and reactants ratios were studied.Furthermore,the structure and thermal properties of terpolymers were primarily characterized and determined by Fourier Transform Infrared Spectroscopy(FTIR),nuclear magnetic resonance(NMR),thermogravimetric analysis(TGA),and gel permeation chromatography(GPC).The results indicate that the terpolymers are random polymers and the yields are low,but the thermal decomposed temperature of terpolymers P(St/MAH/BA)is around 220 ℃ and the average molecular weights(Mw)achieve 1.189×105 g·mol-1.
基金Ministry of Science and Technology of China for Major State Basic Research Projects (2002AA322020)
文摘A silicone acrylate micro-emulsion of multipolymer was prepared by seed emulsion polymerization. The effects of polymerization process, emulsifier rate and amount, initiator rate and amount, polymerization temperature, functional monomers, titration time on performances of emulsion have been discussed in detail.
文摘In this study, P(St-MAA) seed latex particles were first prepared via soap-free emulsion polymerization of styrene (St) and methacrylic acid (MAA), then the seed particles were allowed to swell with St at room temperature, and the P(St-MAA)/P(St- NaSS) core/shell latex particles were then synthesized via seeded emulsion copolymerization of St and sodium styrene sulphonate (NaSS) using AIBN as initiator in the presence of N,N^-methylenebisacrylamide (BAA, water-soluble crosslinker). Results showed that the polymerization could be carried out smoothly when the ratio of BAA to total monomers was less than 3 mol%, the narrow dispersed P(St-MAA) seed particles with the diameter of 150 nm and the P(St-MAA)/P(St-NaSS) core/shell latexes with the particle size of about 200 nm were synthesized. When the 25/75 mole ratio of NaSS/(St + MAA) and 2 tool% of BAA were used in the seeded emulsion polymerization, the resulted P(St-MAA)/P(St-NaSS) latex product showed a low weight loss after water extraction, and the NaSS unit content in the whole particle and in the shell reached 11.7 mol% and 34.6 mol%, resoectivelv.
文摘Despite the great potential of cellulose wood pulp and cellulose nanofibrils as reinforcing filler in thermoplastics,its use is limited due to its tendency to form agglomerates and due to its high hydrophilic character.Here we describe fiberboard composites with high contents of wood pulp or cellulose nanofibrils,and a resin of poly(styrene-methyl-methacrylate-acrylic acid)used as water-based emulsion.Cellulose wood pulp and cellulose nanofibrils were used directly in the form of water suspensions.The method is based on the flocculation of the polymer emulsion followed by agglomeration of a mixture of the polymer emulsion and cellulose suspension,leading to the co-precipitation of the composite material,which can be easily separated from the water phase.Composites with acrylic polymer/cellulose fibers in the proportions of 75:25,50:50 and 25:75 wt%were prepared.Composites were characterized by scanning electron microscopy(SEM),Fourier transform infrared spectroscopy(FTIR),thermogravimetric analysis(TGA),dynamic mechanical analysis(DMA)and water absorption tests.SEM analysis revealed a very good dispersion of the fibers without evidence of agglomeration,which led to superior mechanical properties.These results showed the effectiveness of the methodology and the potential of cellulose wood pulp and CNF as reinforcement fillers in fiberboard composites and any other high fiber-content materials.
基金Financial support for this work was provided by the National Natural Science Foundation of China(No.31370583)Brand Specialty Construction First Stage Projects of Jiangsu Universities 2015.The article was partly presented at the 4^(th) International Conference on Pulping,Papermaking and Biotechnology on Nov.7-9,2012 at Nanjing China.The organizer agreed for the contents to be submitted to Journal of Bioresources and Bioproducts.
文摘Surface sizing is an effective way to increase paper’s water-resistance and printability.The purpose of this study was to study synthesis process to develop an efficient cationic styrene-acrylic acid ester emulsion(SAE)for the surface sizing of paper.Dimethylaminoethyl methacrylate methyl chloride(DMC)was used as the cationic monomer,and cationic starch or native starch was used as the emulsion stabilizer to copolymerize with styrene and butyl acrylate.The results indicated that the SAE synthesized with cationic starch and DMC had a high cationic charge density and a high DMC conversion rate.Paper sized with the cationic SAE had higher surface strength and lower Cobb value than the paper sized with other surface sizing agents such as,anionic SAE,and cationic or oxidized starch.Scanning electron micrographs revealed that the paper sized with a combination of oxidized starch and cationic SAE had smoother surface morphology when compared to the paper sized with oxidized starch alone,or with oxidized starch and anionic SAE.
文摘Stable poly(styrene-co-sodium styrene sulfonate) (P(St-NaSS) nanoparticles with broader size distribution were synthesized by thermal emulsion polymerization without any conventional initiators and emulsifiers. The obtained polymer nanoparticles have higher potential, and the particle sizes have broad distribution. The stability of polymer particles originated from the addition of small amounts of ionic comonomer, NaSS, which can act as an emulsifier in somewhat. The monomer conversion could reach up to about 28 wt% in 48 h, and did not increase by further polymerization when higher polymerization temperature (120℃) was employed. This polymerization system may be give some further understand for mechanism of emulsion polymerization.
文摘Well-defined nonionic hydrophilic ω-acryloyl poly(ethylene oxide) macro-monomer (PEO-A) has been prepared by living anionic polymerization of ethylene oxidewith diphenyl methyl potassium as the initiator and acryloyl chloride as the reaction termi-nating agent. The polymer was characterized by FTIR and SEC. The emulsifier-free emul-sion polymerization of methyl methacrylate (MMA) and n-butyl acrylate (BA) containingvarious concentrations of PEO-A was studied. In all cases stable emulsion coplymerizationsof MMA and BA were obtained. The stabilizing effect was found to be dependent on themolecular weight and the feed amount of the macromonomer.