Crack initiation and subcritical crack growth in glass sheet and SIC bar specimen under static loading were investigated to study the failure process. It has been demonstrated that the lifetime ...Crack initiation and subcritical crack growth in glass sheet and SIC bar specimen under static loading were investigated to study the failure process. It has been demonstrated that the lifetime process of brittle materials involves three possible forms of crack growth: subcritical crack growth, partly subcritical crack growth and instantaneous fracture without subcritical crack growth. Curves of ν-K obtained in step-by-step static fatigue tests and in constant loading rate tests showed different trends for borosilicate glass sheet. α-SiC that is generally considered immune to mechanical fatigue effect and environmental attack was also tested under static loading and the lifetime was measured. The results showed that the threshold load to damage effect was over 80% of the initial strength for the SiC.展开更多
Gamma-emitting radionuclide ^(99m)Tc is globally used for the diagnosis of various pathological conditions owing to its ideal single-photon emission computed tomography (SPECT) characteristics.However,the short half-l...Gamma-emitting radionuclide ^(99m)Tc is globally used for the diagnosis of various pathological conditions owing to its ideal single-photon emission computed tomography (SPECT) characteristics.However,the short half-life of ^(99m)Tc (T_(1/2)=6 h)makes it difficult to store or transport.Thus,the production of ^(99m)Tc is tied to its parent radionuclide ^(99)Mo (T_(1/2)=66 h).The major production paths are based on accelerators and research reactors.The reactor process presents the potential for nuclear proliferation owing to its use of highly enriched uranium (HEU).Accelerator-based methods tend to use deuterium–tritium(D–T) neutron sources but are hindered by the high cost of tritium and its challenging operation.In this study,a new ^(99)Mo production design was developed based on a deuterium–deuterium (D–D) gas dynamic trap fusion neutron source (GDT-FNS) and a subcritical blanket system (SBS) assembly with a low-enriched uranium (LEU) solution.GDT-FNS can provide a relatively high-neutron intensity,which is one of the advantages of ^(99)Mo production.We provide a Monte Carlo-based neutronics analysis covering the calculation of the subcritical multiplication factor (k_(s)) of the SBS,optimization design for the reflector,shielding layer,and ^(99)Mo production capacity.Other calculations,including the neutron flux and nuclear heating distributions,are also provided for an overall evaluation of the production system.The results demonstrated that the SBS meets the nuclear critical safety design requirement (k_(s)<0.97) and maintained a high ^(99)Mo production capacity.The proposed system can generate approximately 157 Ci ^(99)Mo for a stable 24 h operation with a neutron intensity of 1×10^(14) n/s,which can meet 50%of China’s demand in 2025.展开更多
In this letter,the effect of slip boundary on the origin of subcritical transition in two-dimensional chan-nel flows is studied numerically and theoretically.It is shown that both the positive and the negative slip le...In this letter,the effect of slip boundary on the origin of subcritical transition in two-dimensional chan-nel flows is studied numerically and theoretically.It is shown that both the positive and the negative slip lengths will increase the critical Reynolds number of localized wave packet and hence postpone the transition.By applying a variable transformation and expanding the variables about a small slip length,it is illustrated that the slip boundary effect only exists in the second and higher order modulations of the no-slip solution,and hence explains the power law found in simulations,i.e.the relative increment of the critical Reynolds number due to the slip boundary is proportional to the square of the slip length.展开更多
The effects of sulfuric acid-associated mechanical pretreatment on the hydrolysis behavior of pine sawdust were investigated in this study.Sulfuric acid could act as an acidic catalyst to depolymerize holocellulose th...The effects of sulfuric acid-associated mechanical pretreatment on the hydrolysis behavior of pine sawdust were investigated in this study.Sulfuric acid could act as an acidic catalyst to depolymerize holocellulose through cleavage of the glycosidic bonds,the dissociation energies of which were supplied by the impact of a ball on pine sawdust,during milling.The destruction of glycosidic and hydrogen bonds in pine sawdust resulted in a decrease of crystallinity and an increase of water solubility.The sulfuric acid could promote the hydrolysis of holocellulose and its hydrolysis products.It also destroyed the chemical linkages between holocellulose and lignin during ball milling.The cleavage of chemical linkages with holocellulose made lignin more difficult to hydrolyze in subcritical water,and higher activation energy was needed to hydrolyze pretreated pine sawdust at higher reaction temperatures.It also led to the formation of glucose char and aromatic-linked polymer char from the hydrolysis products of holocellulose.展开更多
The accelerator-driven subcritical system (ADS) with a hard neutron energy spectrum was used to study transmutation of minor actinides (MAs). The aim of the study was to improve the efficiency of MA transmutation whil...The accelerator-driven subcritical system (ADS) with a hard neutron energy spectrum was used to study transmutation of minor actinides (MAs). The aim of the study was to improve the efficiency of MA transmutation while ensuring that variations in the effective multiplication factor (keff) remained within safe margins during reactor operation. All calculations were completed using code COUPLE3.0. The subcritical reactor was operated at a thermal power level of 800 MW, and a mixture of mononitrides of MAs and plutonium (Pu) was used as fuel. Zirconium nitride (ZrN) was used as an inert matrix in the fuel elements. The initial mass composition in terms of weight percentages in the heavy metal component (IHM) was 30.6% Pu/IHM and 69.4% MA/IHM. To verify the feasibility of this MA loading scheme, variations in keff, the amplification factor of the core, maximum power density and the content of MAs and Pu were calculated over six refueling cycles. Each cycle was of 600 days duration, and therefore, there were 3600 effective full power days. Results demonstrated that the effective transmutation support ratio of MAs was approximately 28, and the ADS was able to efficiently transmute MAs. The changes in other physical parameters were also within their normal ranges.It is concluded that the proposed MA transmutation scheme for an ADS core is reasonable.展开更多
Effect of cryogenic treatment on the microstructure, hardening behavior and abrasion resistance of 14Cr2Mn2V high chromium cast iron (HCCI) subjected to subcritical treatment was investigated. The results show that ...Effect of cryogenic treatment on the microstructure, hardening behavior and abrasion resistance of 14Cr2Mn2V high chromium cast iron (HCCI) subjected to subcritical treatment was investigated. The results show that cryogenic treatment after subcritical treatment can obviously improve the hardness and abrasion resistance of HCCI because abundant retained austenite is transformed into martensite and fine secondary carbides E(Fe, Cr)23 C6 ] precipitate. The amount of martensite and precipitated secondary carbide in HCCI experiencing subcritical treatment followed by cryogenic treatment was more than that experiencing the subcritical treatment followed by air cooling. When the abrasion resistance of HCCI reaches the maximum, its microstructure contains about 15 % retained austenite. Cryogenic treatment can further reduce the austenite content but the retained austenite cannot be transformed in to martensite completely.展开更多
The study of accelerator-driven subcritical reactor systems(ADSs) has been an important research topic in the field of nuclear energy for years. The main code applied in ADS research is MCNPX, which was developed by L...The study of accelerator-driven subcritical reactor systems(ADSs) has been an important research topic in the field of nuclear energy for years. The main code applied in ADS research is MCNPX, which was developed by Los Alamos National Laboratory. We studied the application of the open-source Monte Carlo codes FLUKA and OpenMC to a coupled ADS calculation. The FLUKA code was used to simulate the reaction of highenergy protons with the nucleus of the target material in the ADS, which produces spallation neutrons. Information on the spallation neutrons, such as their energy, position,direction, and weight, can be recorded by a user-defined routine called FLUSCW provided by FLUKA. Then, the information was stored in an external neutron source file in HDF5 format by using a conversion code, as required by the OpenMC calculation. Finally, the fixed-source calculation function of OpenMC was applied to simulate the transport of spallation neutrons and obtain the distribution of the neutron flux in the core region. In the coupled calculation, the high-energy cross-section library JENDL4.0/HE in ACE format produced by NJOY2016 was applied in the OpenMC transport simulation. The OECD–ADS benchmark problem was calculated, and the results were compared with those obtained using MCNPX. It was found that the flux calculations performed by FLUKA–OpenMC and MCNPX were in agreement, so the coupling calculation method for ADS is reasonable and feasible.展开更多
Effects of reaction parameter on yield of benzaldehyde produced from toluene oxidization using hydrogen peroxide in subcritical water are investigated. The experimental results show that if the molar ratio of hydrogen...Effects of reaction parameter on yield of benzaldehyde produced from toluene oxidization using hydrogen peroxide in subcritical water are investigated. The experimental results show that if the molar ratio of hydrogen peroxide to toluene is controlled within a reasonable range, the by-products may be neglected. The optimum technology of toluene oxidization to benzaldehyde is reaction time 60 min, reaction temperature 350℃, molar ratio of hydrogen peroxide to toluene 3.5. The yield of benzaldehyde can reach 17.2 % under the optimum condition. Research results of chemical reaction kinetics show that the consecutive reaction consists of two first-order reaction, and activation energy of these two reactions are 89 kJ·mol^-1 and 76 kJ·mol^-1 respectively,展开更多
Subcritical and supercritical water gasification of petroleum coke and asphaltene was performed at variable temperatures(350–650°C),feed concentrations(15–30 wt%)and reaction times(15–60 min).Nickel-impregnate...Subcritical and supercritical water gasification of petroleum coke and asphaltene was performed at variable temperatures(350–650°C),feed concentrations(15–30 wt%)and reaction times(15–60 min).Nickel-impregnated activated carbon(Ni/AC)was synthesized as a catalyst for enhancing syngas yields at optimal gasification conditions(650°C,15 wt%and 60 min).Structural chemistry of precursors and chars developed at different gasification temperatures was studied using physicochemical and synchrotronbased approaches such as carbon–hydrogen–nitrogen–sulfur(CHNS)analysis,thermogravimetric and differential thermogravimetric analysis(TGA/DTA),scanning electron microscopy(SEM),Fourier-Transform Infrared spectroscopy(FTIR),Raman spectroscopy,X-ray diffraction(XRD)and X-ray absorption spectroscopy(XAS).Asphaltene testified to be a better precursor for catalytic hydrothermal gasification leading to 11.97 mmol/g of total gas yield compared to petroleum coke(8.04 mmol/g).In particular,supercritical water gasification using 5 wt%Ni/AC at 650°C with 15 wt%feed concentration for 60 min resulted in 4.17 and 2.98 mmol/g of H_2from asphaltene and petroleum coke,respectively.Under the same conditions,the respective CH_4yields from catalytic gasification of asphaltene and petroleum coke were 2.54and 1.07 mmol/g.Nonetheless,asphaltene also seemed to an attractive feedstock for the production of highly aromatic chars through hydrothermal gasification.展开更多
The Hopf bifurcations of an airfoil flutter system with a cubic nonlinearity are investigated, with the flow speed as the bifurcation parameter. The center manifold theory and complex normal form method are Used to ob...The Hopf bifurcations of an airfoil flutter system with a cubic nonlinearity are investigated, with the flow speed as the bifurcation parameter. The center manifold theory and complex normal form method are Used to obtain the bifurcation equation. Interestingly, for a certain linear pitching stiffness the Hopf bifurcation is both supercritical and subcritical. It is found, mathematically, this is caused by the fact that one coefficient in the bifurcation equation does not contain the first power of the bifurcation parameter. The solutions of the bifurcation equation are validated by the equivalent linearization method and incremental harmonic balance method.展开更多
Diapycnal mixing plays an important role in the ocean circulation.Internal waves are a kind of bridge relating the diapycnal mixing to external sources of mechanical energy.Difficulty in obtaining eigen solutions of i...Diapycnal mixing plays an important role in the ocean circulation.Internal waves are a kind of bridge relating the diapycnal mixing to external sources of mechanical energy.Difficulty in obtaining eigen solutions of internal waves over curved topography is a limitation for further theoretical study on the generation problem and scattering process.In this study,a kind of transform method is put forward to derive the eigen solutions of internal waves over subcritical topography in twodimensional and linear framework.The transform converts the curved topography in physical space to flat bottom in transform space while the governing equation of internal waves is still hyperbolic if proper transform function is selected.Thus,one can obtain eigen solutions of internal waves in the transform space.Several examples of transform functions,which convert the linear slope,the convex slope,and the concave slope to flat bottom,and the corresponding eigen solutions are illustrated.A method,using a polynomial to approximate the transform function and least squares method to estimate the undetermined coefficients in the polynomial,is introduced to calculate the approximate expression of the transform function for the given subcritical topography.展开更多
We analyze the exponential decay property of solutions of the semilinear wave equation in bounded domain Ω of R^N with a damping term which is effective on the exterior of a ball and boundary conditions of the Cauchy...We analyze the exponential decay property of solutions of the semilinear wave equation in bounded domain Ω of R^N with a damping term which is effective on the exterior of a ball and boundary conditions of the Cauchy-Ventcel type. Under suitable and natural assumptions on the nonlinearity, we prove that the exponential decay holds locally uniformly for finite energy solutions provided the nonlinearity is subcritical at infinity. Subcriticality means, roughly speaking, that the nonlinearity grows at infinity at most as a power p 〈 5. The results obtained in R^3 and RN by B. Dehman, G. Lebeau and E. Zuazua on the inequalities of the classical energy (which estimate the total energy of solutions in terms of the energy localized in the exterior of a ball) and on Strichartz's estimates, allow us to give an application to the stabilization controllability of the semilinear wave equation in a bounded domain of R^N with a subcritical nonlinearity on the domain and its boundary, and conditions on the boundary of Cauchy-Ventcel type.展开更多
Flow around an oscillating cylinder in a subcritical region are numerically studied with a lattice Boltzmann method(LBM). The effects of the Reynolds number,oscillation amplitude and frequency on the vortex wake modes...Flow around an oscillating cylinder in a subcritical region are numerically studied with a lattice Boltzmann method(LBM). The effects of the Reynolds number,oscillation amplitude and frequency on the vortex wake modes and hydrodynamics forces on the cylinder surface are systematically investigated. Special attention is paid to the phenomenon of resonance induced by the cylinder oscillation. The results demonstrate that vortex shedding can be excited extensively under subcritical conditions, and the response region of vibration frequency broadens with increasing Reynolds number and oscillation amplitude. Two distinct types of vortex shedding regimes are observed. The first type of vortex shedding regime(VSR I) is excited at low frequencies close to the intrinsic frequency of flow, and the second type of vortex shedding regime(VSR II)occurs at high frequencies with the Reynolds number close to the critical value. In the VSR I, a pair of alternately rotating vortices are shed in the wake per oscillation cycle,and lock-in/synchronization occurs, while in the VSR II, two alternately rotating vortices are shed for several oscillation cycles, and the vortex shedding frequency is close to that of a stationary cylinder under the critical condition. The excitation mechanisms of the two types of vortex shedding modes are analyzed separately.展开更多
The utilization of neutrons markedly affects the medical isotope yield of a subcritical system driven by an external D-T neutron source.The general methods to improve the utilization of neutrons include moderating mul...The utilization of neutrons markedly affects the medical isotope yield of a subcritical system driven by an external D-T neutron source.The general methods to improve the utilization of neutrons include moderating multiplying,and reflecting neutrons,which ignores the use of neutrons that backscatter to the source direction.In this study,a stacked structure was formed by assembling the multiplier and the low-enriched uranium solution to enable the full use of neutrons that backscatter to the source direction and further improve the utilization of neutrons.A model based on SuperMC was used to evaluate the neutronics and safety behavior of the subcritical system,such as the neutron effective multiplication factor,neutron energy spectrum,medical isotope yield,and heat deposition.Based on the calculation results,when the intensity of the neutron source was 59×10^(13)n/s,the optimized design with a stacked structure could increase the yield of ^(99)Mo to182 Ci/day,which is approximately 16% higher than that obtained with a single-layer structure.The inlet H_(2)O coolant velocity of 1.0 m/s and initial temperature of 20℃ were also found to be sufficient to prevent boiling of the fuel solution.展开更多
Euphausia pacific is an important source of natural astaxanthin.Studies were carried out to assess the extractability of astaxanthin from E.pacific using subcritical 1,1,1,2-tetrafluoroethane(R134a).To examine the eff...Euphausia pacific is an important source of natural astaxanthin.Studies were carried out to assess the extractability of astaxanthin from E.pacific using subcritical 1,1,1,2-tetrafluoroethane(R134a).To examine the effects of multiple process variables on the extraction yield,astaxanthin was extracted under various conditions of pressure(30-150 bar),temperature(303-343 K),time(10-50 min),flow rate(2-10 g min-1),moisture content(5.5%-63.61%),and particle size(0.25-0.109 mm).The results showed that the extraction yield increased with temperature,pressure,time and flow rate,but decreased with moisture content and particle size.A maximum yield of 87.74% was obtained under conditions of 100 bar,333 K,and 30 min with a flow rate of 6 g min-1 and a moisture content of 5.5%.The substantial astaxanthin yield obtained under low-pressure conditions demonstrates that subcritical R134a is a good alternative to CO 2 for extraction of astaxanthin from E.pacific.展开更多
During recent years, a new generation of nuclear reactors, known as “Accelerator Driven Subcritical Reactors”, has been developed. One of the new application aspects for such reactors (besides transmutation of High ...During recent years, a new generation of nuclear reactors, known as “Accelerator Driven Subcritical Reactors”, has been developed. One of the new application aspects for such reactors (besides transmutation of High Level Waste and burning Minor Actinides) is usage of thorium as nuclear fuel. In this work a subcritical core in experimental scale is simulated by MCNPX code. The core contains two types of fuel assemblies: (85% ThO2 + 15% UO2) and MOX (U-Pu). In the first step, only the thorium-contained fuel assemblies are loaded into the core. Criticality calculations using MCNPX show that the keff is so low that the fuel assemblies cannot run the subcritical core. This implies that MOX (U-Pu) assemblies must be loaded as well. Neutronic parameters of the thorium- fueled Accelerator Driven Subcritical core are then calculated as well as some other parameters related to accelerator coupled with the core. The main objective of this simulation is to study the behavior of Accelerator Driven Subcritical core with thorium assemblies.展开更多
For the first time,the solubility ofβ-carotene in pure and ethanol-modified subcritical water(SW)using the static method was determined.The experimental runs were performed at a temperature ranging from 298.15 to 403...For the first time,the solubility ofβ-carotene in pure and ethanol-modified subcritical water(SW)using the static method was determined.The experimental runs were performed at a temperature ranging from 298.15 to 403.15 K and 0–10%(w/w)of ethanol as a modifier at a constant pressure of 5 MPa.Samples were analyzed by UV–vis spectrophotometer.The solubility ofβ-carotene was found to range from 1.084×10^-8 to 227.1×10^-8 mol fractions in the subcritical water in above mentioned conditions.The obtainedβ-carotene solubility data were correlated using the linear model and modified Apelblat model.The obtained results showed the modified Apelblat model was better for estimating the solubility ofβ-carotene in SW.The values of the rootmean-square deviation(RMSD)between experimental and correlated data were calculated and used as the index of validity and accuracy for the model.Also,thermodynamic properties of the solution such as the Gibbs free energy of solution,enthalpy,and entropy of solution were estimated.展开更多
The long-term stability of the roof is particularly important in designing underground rock structures.To estimate the durability of roof strata in underground excavation,a computation scheme of subcritical crack grow...The long-term stability of the roof is particularly important in designing underground rock structures.To estimate the durability of roof strata in underground excavation,a computation scheme of subcritical crack growth is proposed in this study.By adopting the proposed method,the potential collapse location of strata is derivable in accordance with a static model,the durability of roof strata can be estimated,a dynamic time step control strategy is achieved to balance the accuracy and speed of computing,and the initial crack size of rock can be estimated.In addition to the above,a mechanical model of underground excavation with non-uniformly distributed loads and partially yielded foundation is presented as the prototypical case.A set of case studies is carried out that showcase a power correlation between applied stress and roof durability.The allowable applied tensile stress for a 100-year life cycle is about 76%of the tensile strength.By using the proposed subcritical crack growth computation scheme,the roof stability in an underground excavation can be identified not only from the spatial view but also from the temporal perspective.展开更多
Accelerator-driven systems based on molten salt fuel have several unique advantages and features for advanced nuclear fuel utilization.The aim of this work was to study the Th-U breeding capability in such systems,kno...Accelerator-driven systems based on molten salt fuel have several unique advantages and features for advanced nuclear fuel utilization.The aim of this work was to study the Th-U breeding capability in such systems,known as‘‘accelerator-driven subcritical molten salt reactors’’(ADS–MSRs).Breeding capacities including conversion ratio and net^(233)U production for various subcriticalities and different minor actinides(MA)loadings were analyzed for an ADS–MSR.The results show that the subcriticality of the core has a considerable effect on the Th-U breeding.A high subcriticality is favorable to improving the conversion ratio,increasing the net^(233)U production,and reducing the doubling time.Specifically,the doubling time for k_(eff)of 0.99 is larger than 80 years,while the counterpart for k_(eff)of 0.93 is only approximately22 years.Nevertheless,in an ADS–MSR with a high initial MA loading,MA results in a non-negligible^(233)U depletion in the first two decades,while increasing the net^(233)U production compared to reactors without MA loading.During the 50 years of operation,for the subcritical reactor(k_(eff)0:97)with MA fraction increasing from 1 to 14%,the net^(233)U production increases from 3.94 to 8.24 t.展开更多
基金This work was supported by the National Natural Science Foundation of China(No.59872035 and No.59902227)the Science Foundation of Beijing(2002019).
文摘Crack initiation and subcritical crack growth in glass sheet and SIC bar specimen under static loading were investigated to study the failure process. It has been demonstrated that the lifetime process of brittle materials involves three possible forms of crack growth: subcritical crack growth, partly subcritical crack growth and instantaneous fracture without subcritical crack growth. Curves of ν-K obtained in step-by-step static fatigue tests and in constant loading rate tests showed different trends for borosilicate glass sheet. α-SiC that is generally considered immune to mechanical fatigue effect and environmental attack was also tested under static loading and the lifetime was measured. The results showed that the threshold load to damage effect was over 80% of the initial strength for the SiC.
基金supported by Anhui Provincial Key R&D Program (202104g0102007)Hefei Municipal Natural Science Foundation (2022011)+2 种基金Collaborative Innovation Program of Hefei Science CenterChinese Academy of Sciences(2022HSC CIP024)International Partnership Program of Chinese Academy of Sciences (116134KYSB20200001)。
文摘Gamma-emitting radionuclide ^(99m)Tc is globally used for the diagnosis of various pathological conditions owing to its ideal single-photon emission computed tomography (SPECT) characteristics.However,the short half-life of ^(99m)Tc (T_(1/2)=6 h)makes it difficult to store or transport.Thus,the production of ^(99m)Tc is tied to its parent radionuclide ^(99)Mo (T_(1/2)=66 h).The major production paths are based on accelerators and research reactors.The reactor process presents the potential for nuclear proliferation owing to its use of highly enriched uranium (HEU).Accelerator-based methods tend to use deuterium–tritium(D–T) neutron sources but are hindered by the high cost of tritium and its challenging operation.In this study,a new ^(99)Mo production design was developed based on a deuterium–deuterium (D–D) gas dynamic trap fusion neutron source (GDT-FNS) and a subcritical blanket system (SBS) assembly with a low-enriched uranium (LEU) solution.GDT-FNS can provide a relatively high-neutron intensity,which is one of the advantages of ^(99)Mo production.We provide a Monte Carlo-based neutronics analysis covering the calculation of the subcritical multiplication factor (k_(s)) of the SBS,optimization design for the reflector,shielding layer,and ^(99)Mo production capacity.Other calculations,including the neutron flux and nuclear heating distributions,are also provided for an overall evaluation of the production system.The results demonstrated that the SBS meets the nuclear critical safety design requirement (k_(s)<0.97) and maintained a high ^(99)Mo production capacity.The proposed system can generate approximately 157 Ci ^(99)Mo for a stable 24 h operation with a neutron intensity of 1×10^(14) n/s,which can meet 50%of China’s demand in 2025.
基金The present research is financially supported by the National Natural Science Foundation of China(Grants No.91752203).
文摘In this letter,the effect of slip boundary on the origin of subcritical transition in two-dimensional chan-nel flows is studied numerically and theoretically.It is shown that both the positive and the negative slip lengths will increase the critical Reynolds number of localized wave packet and hence postpone the transition.By applying a variable transformation and expanding the variables about a small slip length,it is illustrated that the slip boundary effect only exists in the second and higher order modulations of the no-slip solution,and hence explains the power law found in simulations,i.e.the relative increment of the critical Reynolds number due to the slip boundary is proportional to the square of the slip length.
基金supported by the National Natural Science Foundation of China(22078225)the Natural Science Foundation of Zhejiang Province(LGF22E080025 and LHY22E080005)。
文摘The effects of sulfuric acid-associated mechanical pretreatment on the hydrolysis behavior of pine sawdust were investigated in this study.Sulfuric acid could act as an acidic catalyst to depolymerize holocellulose through cleavage of the glycosidic bonds,the dissociation energies of which were supplied by the impact of a ball on pine sawdust,during milling.The destruction of glycosidic and hydrogen bonds in pine sawdust resulted in a decrease of crystallinity and an increase of water solubility.The sulfuric acid could promote the hydrolysis of holocellulose and its hydrolysis products.It also destroyed the chemical linkages between holocellulose and lignin during ball milling.The cleavage of chemical linkages with holocellulose made lignin more difficult to hydrolyze in subcritical water,and higher activation energy was needed to hydrolyze pretreated pine sawdust at higher reaction temperatures.It also led to the formation of glucose char and aromatic-linked polymer char from the hydrolysis products of holocellulose.
基金supported by the Strategic Priority Research Program of The Chinese Academy of Sciences(No.XDA21010202)
文摘The accelerator-driven subcritical system (ADS) with a hard neutron energy spectrum was used to study transmutation of minor actinides (MAs). The aim of the study was to improve the efficiency of MA transmutation while ensuring that variations in the effective multiplication factor (keff) remained within safe margins during reactor operation. All calculations were completed using code COUPLE3.0. The subcritical reactor was operated at a thermal power level of 800 MW, and a mixture of mononitrides of MAs and plutonium (Pu) was used as fuel. Zirconium nitride (ZrN) was used as an inert matrix in the fuel elements. The initial mass composition in terms of weight percentages in the heavy metal component (IHM) was 30.6% Pu/IHM and 69.4% MA/IHM. To verify the feasibility of this MA loading scheme, variations in keff, the amplification factor of the core, maximum power density and the content of MAs and Pu were calculated over six refueling cycles. Each cycle was of 600 days duration, and therefore, there were 3600 effective full power days. Results demonstrated that the effective transmutation support ratio of MAs was approximately 28, and the ADS was able to efficiently transmute MAs. The changes in other physical parameters were also within their normal ranges.It is concluded that the proposed MA transmutation scheme for an ADS core is reasonable.
文摘Effect of cryogenic treatment on the microstructure, hardening behavior and abrasion resistance of 14Cr2Mn2V high chromium cast iron (HCCI) subjected to subcritical treatment was investigated. The results show that cryogenic treatment after subcritical treatment can obviously improve the hardness and abrasion resistance of HCCI because abundant retained austenite is transformed into martensite and fine secondary carbides E(Fe, Cr)23 C6 ] precipitate. The amount of martensite and precipitated secondary carbide in HCCI experiencing subcritical treatment followed by cryogenic treatment was more than that experiencing the subcritical treatment followed by air cooling. When the abrasion resistance of HCCI reaches the maximum, its microstructure contains about 15 % retained austenite. Cryogenic treatment can further reduce the austenite content but the retained austenite cannot be transformed in to martensite completely.
基金supported by the ‘‘Strategic Priority Research Program’’ of the Chinese Academy of Sciences(No.XDA03030102)
文摘The study of accelerator-driven subcritical reactor systems(ADSs) has been an important research topic in the field of nuclear energy for years. The main code applied in ADS research is MCNPX, which was developed by Los Alamos National Laboratory. We studied the application of the open-source Monte Carlo codes FLUKA and OpenMC to a coupled ADS calculation. The FLUKA code was used to simulate the reaction of highenergy protons with the nucleus of the target material in the ADS, which produces spallation neutrons. Information on the spallation neutrons, such as their energy, position,direction, and weight, can be recorded by a user-defined routine called FLUSCW provided by FLUKA. Then, the information was stored in an external neutron source file in HDF5 format by using a conversion code, as required by the OpenMC calculation. Finally, the fixed-source calculation function of OpenMC was applied to simulate the transport of spallation neutrons and obtain the distribution of the neutron flux in the core region. In the coupled calculation, the high-energy cross-section library JENDL4.0/HE in ACE format produced by NJOY2016 was applied in the OpenMC transport simulation. The OECD–ADS benchmark problem was calculated, and the results were compared with those obtained using MCNPX. It was found that the flux calculations performed by FLUKA–OpenMC and MCNPX were in agreement, so the coupling calculation method for ADS is reasonable and feasible.
文摘Effects of reaction parameter on yield of benzaldehyde produced from toluene oxidization using hydrogen peroxide in subcritical water are investigated. The experimental results show that if the molar ratio of hydrogen peroxide to toluene is controlled within a reasonable range, the by-products may be neglected. The optimum technology of toluene oxidization to benzaldehyde is reaction time 60 min, reaction temperature 350℃, molar ratio of hydrogen peroxide to toluene 3.5. The yield of benzaldehyde can reach 17.2 % under the optimum condition. Research results of chemical reaction kinetics show that the consecutive reaction consists of two first-order reaction, and activation energy of these two reactions are 89 kJ·mol^-1 and 76 kJ·mol^-1 respectively,
基金the Natural Sciences and Engineering Research Council of Canada (NSERC)Canada Research Chair program for funding this bioenergy research
文摘Subcritical and supercritical water gasification of petroleum coke and asphaltene was performed at variable temperatures(350–650°C),feed concentrations(15–30 wt%)and reaction times(15–60 min).Nickel-impregnated activated carbon(Ni/AC)was synthesized as a catalyst for enhancing syngas yields at optimal gasification conditions(650°C,15 wt%and 60 min).Structural chemistry of precursors and chars developed at different gasification temperatures was studied using physicochemical and synchrotronbased approaches such as carbon–hydrogen–nitrogen–sulfur(CHNS)analysis,thermogravimetric and differential thermogravimetric analysis(TGA/DTA),scanning electron microscopy(SEM),Fourier-Transform Infrared spectroscopy(FTIR),Raman spectroscopy,X-ray diffraction(XRD)and X-ray absorption spectroscopy(XAS).Asphaltene testified to be a better precursor for catalytic hydrothermal gasification leading to 11.97 mmol/g of total gas yield compared to petroleum coke(8.04 mmol/g).In particular,supercritical water gasification using 5 wt%Ni/AC at 650°C with 15 wt%feed concentration for 60 min resulted in 4.17 and 2.98 mmol/g of H_2from asphaltene and petroleum coke,respectively.Under the same conditions,the respective CH_4yields from catalytic gasification of asphaltene and petroleum coke were 2.54and 1.07 mmol/g.Nonetheless,asphaltene also seemed to an attractive feedstock for the production of highly aromatic chars through hydrothermal gasification.
基金Project supported by the National Natural Science Foundation of China (No.10772202)the Doctoral Foundation of Ministry of Education of China (No.20050558032)the Natural Science Foundation of Guangdong Province (Nos.07003680 and 05003295)
文摘The Hopf bifurcations of an airfoil flutter system with a cubic nonlinearity are investigated, with the flow speed as the bifurcation parameter. The center manifold theory and complex normal form method are Used to obtain the bifurcation equation. Interestingly, for a certain linear pitching stiffness the Hopf bifurcation is both supercritical and subcritical. It is found, mathematically, this is caused by the fact that one coefficient in the bifurcation equation does not contain the first power of the bifurcation parameter. The solutions of the bifurcation equation are validated by the equivalent linearization method and incremental harmonic balance method.
基金the National Nature Science Foundation of China under contract No. 40876015the National High Technology Research and Development Program of China (863 Program) under contract No. 2008AA09A402
文摘Diapycnal mixing plays an important role in the ocean circulation.Internal waves are a kind of bridge relating the diapycnal mixing to external sources of mechanical energy.Difficulty in obtaining eigen solutions of internal waves over curved topography is a limitation for further theoretical study on the generation problem and scattering process.In this study,a kind of transform method is put forward to derive the eigen solutions of internal waves over subcritical topography in twodimensional and linear framework.The transform converts the curved topography in physical space to flat bottom in transform space while the governing equation of internal waves is still hyperbolic if proper transform function is selected.Thus,one can obtain eigen solutions of internal waves in the transform space.Several examples of transform functions,which convert the linear slope,the convex slope,and the concave slope to flat bottom,and the corresponding eigen solutions are illustrated.A method,using a polynomial to approximate the transform function and least squares method to estimate the undetermined coefficients in the polynomial,is introduced to calculate the approximate expression of the transform function for the given subcritical topography.
文摘We analyze the exponential decay property of solutions of the semilinear wave equation in bounded domain Ω of R^N with a damping term which is effective on the exterior of a ball and boundary conditions of the Cauchy-Ventcel type. Under suitable and natural assumptions on the nonlinearity, we prove that the exponential decay holds locally uniformly for finite energy solutions provided the nonlinearity is subcritical at infinity. Subcriticality means, roughly speaking, that the nonlinearity grows at infinity at most as a power p 〈 5. The results obtained in R^3 and RN by B. Dehman, G. Lebeau and E. Zuazua on the inequalities of the classical energy (which estimate the total energy of solutions in terms of the energy localized in the exterior of a ball) and on Strichartz's estimates, allow us to give an application to the stabilization controllability of the semilinear wave equation in a bounded domain of R^N with a subcritical nonlinearity on the domain and its boundary, and conditions on the boundary of Cauchy-Ventcel type.
基金Project supported by the National Natural Science Foundation of China(No.11402129)the Zhejiang Provincial Natural Science Foundation of China(No.LY17A020002)
文摘Flow around an oscillating cylinder in a subcritical region are numerically studied with a lattice Boltzmann method(LBM). The effects of the Reynolds number,oscillation amplitude and frequency on the vortex wake modes and hydrodynamics forces on the cylinder surface are systematically investigated. Special attention is paid to the phenomenon of resonance induced by the cylinder oscillation. The results demonstrate that vortex shedding can be excited extensively under subcritical conditions, and the response region of vibration frequency broadens with increasing Reynolds number and oscillation amplitude. Two distinct types of vortex shedding regimes are observed. The first type of vortex shedding regime(VSR I) is excited at low frequencies close to the intrinsic frequency of flow, and the second type of vortex shedding regime(VSR II)occurs at high frequencies with the Reynolds number close to the critical value. In the VSR I, a pair of alternately rotating vortices are shed in the wake per oscillation cycle,and lock-in/synchronization occurs, while in the VSR II, two alternately rotating vortices are shed for several oscillation cycles, and the vortex shedding frequency is close to that of a stationary cylinder under the critical condition. The excitation mechanisms of the two types of vortex shedding modes are analyzed separately.
基金supported by the Natural Science Foundation of Anhui Province(No.1808085MA10)Anhui Provincial Key R&D Program(No.202104g0102007)the National Natural Science Foundation of China(No.21805283)。
文摘The utilization of neutrons markedly affects the medical isotope yield of a subcritical system driven by an external D-T neutron source.The general methods to improve the utilization of neutrons include moderating multiplying,and reflecting neutrons,which ignores the use of neutrons that backscatter to the source direction.In this study,a stacked structure was formed by assembling the multiplier and the low-enriched uranium solution to enable the full use of neutrons that backscatter to the source direction and further improve the utilization of neutrons.A model based on SuperMC was used to evaluate the neutronics and safety behavior of the subcritical system,such as the neutron effective multiplication factor,neutron energy spectrum,medical isotope yield,and heat deposition.Based on the calculation results,when the intensity of the neutron source was 59×10^(13)n/s,the optimized design with a stacked structure could increase the yield of ^(99)Mo to182 Ci/day,which is approximately 16% higher than that obtained with a single-layer structure.The inlet H_(2)O coolant velocity of 1.0 m/s and initial temperature of 20℃ were also found to be sufficient to prevent boiling of the fuel solution.
基金supported by the National Natural Science Foundation of China (No.31071541)
文摘Euphausia pacific is an important source of natural astaxanthin.Studies were carried out to assess the extractability of astaxanthin from E.pacific using subcritical 1,1,1,2-tetrafluoroethane(R134a).To examine the effects of multiple process variables on the extraction yield,astaxanthin was extracted under various conditions of pressure(30-150 bar),temperature(303-343 K),time(10-50 min),flow rate(2-10 g min-1),moisture content(5.5%-63.61%),and particle size(0.25-0.109 mm).The results showed that the extraction yield increased with temperature,pressure,time and flow rate,but decreased with moisture content and particle size.A maximum yield of 87.74% was obtained under conditions of 100 bar,333 K,and 30 min with a flow rate of 6 g min-1 and a moisture content of 5.5%.The substantial astaxanthin yield obtained under low-pressure conditions demonstrates that subcritical R134a is a good alternative to CO 2 for extraction of astaxanthin from E.pacific.
文摘During recent years, a new generation of nuclear reactors, known as “Accelerator Driven Subcritical Reactors”, has been developed. One of the new application aspects for such reactors (besides transmutation of High Level Waste and burning Minor Actinides) is usage of thorium as nuclear fuel. In this work a subcritical core in experimental scale is simulated by MCNPX code. The core contains two types of fuel assemblies: (85% ThO2 + 15% UO2) and MOX (U-Pu). In the first step, only the thorium-contained fuel assemblies are loaded into the core. Criticality calculations using MCNPX show that the keff is so low that the fuel assemblies cannot run the subcritical core. This implies that MOX (U-Pu) assemblies must be loaded as well. Neutronic parameters of the thorium- fueled Accelerator Driven Subcritical core are then calculated as well as some other parameters related to accelerator coupled with the core. The main objective of this simulation is to study the behavior of Accelerator Driven Subcritical core with thorium assemblies.
基金The authors tend to appreciate for the partial financial support from Semnan University Science and Technology Park.
文摘For the first time,the solubility ofβ-carotene in pure and ethanol-modified subcritical water(SW)using the static method was determined.The experimental runs were performed at a temperature ranging from 298.15 to 403.15 K and 0–10%(w/w)of ethanol as a modifier at a constant pressure of 5 MPa.Samples were analyzed by UV–vis spectrophotometer.The solubility ofβ-carotene was found to range from 1.084×10^-8 to 227.1×10^-8 mol fractions in the subcritical water in above mentioned conditions.The obtainedβ-carotene solubility data were correlated using the linear model and modified Apelblat model.The obtained results showed the modified Apelblat model was better for estimating the solubility ofβ-carotene in SW.The values of the rootmean-square deviation(RMSD)between experimental and correlated data were calculated and used as the index of validity and accuracy for the model.Also,thermodynamic properties of the solution such as the Gibbs free energy of solution,enthalpy,and entropy of solution were estimated.
基金China Scholarship Council(CSC)The University of Queensland for a Ph D fellowship。
文摘The long-term stability of the roof is particularly important in designing underground rock structures.To estimate the durability of roof strata in underground excavation,a computation scheme of subcritical crack growth is proposed in this study.By adopting the proposed method,the potential collapse location of strata is derivable in accordance with a static model,the durability of roof strata can be estimated,a dynamic time step control strategy is achieved to balance the accuracy and speed of computing,and the initial crack size of rock can be estimated.In addition to the above,a mechanical model of underground excavation with non-uniformly distributed loads and partially yielded foundation is presented as the prototypical case.A set of case studies is carried out that showcase a power correlation between applied stress and roof durability.The allowable applied tensile stress for a 100-year life cycle is about 76%of the tensile strength.By using the proposed subcritical crack growth computation scheme,the roof stability in an underground excavation can be identified not only from the spatial view but also from the temporal perspective.
基金supported by the Chinese TMSR Strategic Pioneer Science and Technology Project(No.XDA02010000)the Frontier Science Key Program of the Chinese Academy of Sciences(No.QYZDY-SSW-JSC016)
文摘Accelerator-driven systems based on molten salt fuel have several unique advantages and features for advanced nuclear fuel utilization.The aim of this work was to study the Th-U breeding capability in such systems,known as‘‘accelerator-driven subcritical molten salt reactors’’(ADS–MSRs).Breeding capacities including conversion ratio and net^(233)U production for various subcriticalities and different minor actinides(MA)loadings were analyzed for an ADS–MSR.The results show that the subcriticality of the core has a considerable effect on the Th-U breeding.A high subcriticality is favorable to improving the conversion ratio,increasing the net^(233)U production,and reducing the doubling time.Specifically,the doubling time for k_(eff)of 0.99 is larger than 80 years,while the counterpart for k_(eff)of 0.93 is only approximately22 years.Nevertheless,in an ADS–MSR with a high initial MA loading,MA results in a non-negligible^(233)U depletion in the first two decades,while increasing the net^(233)U production compared to reactors without MA loading.During the 50 years of operation,for the subcritical reactor(k_(eff)0:97)with MA fraction increasing from 1 to 14%,the net^(233)U production increases from 3.94 to 8.24 t.