Exploring the relationship between ambient sulfur dioxide and semen quality parameters:A systematic review and meta-analysis

Objective:To investigate the relationship between ambient sulfur dioxide(SO2)exposure and semen quality parameters.Methods:A systematic literature search was conducted to identify relevant studies investigating the association between SO2 exposure and semen quality parameters.This search encompassed the timeframe from January 2000 to May 2023 and included electronic databases such as Web of Science,Google Scholar,PubMed,Cochrane,and Scopus.Pooled effect estimates with 95%confidence intervals(CI)were calculated using percent changes(PC).The meta-analysis included seven studies with 6711 participants and 15087 semen samples.Results:The results revealed a significant negative association between ambient SO2 exposure and certain semen quality parameters.In particular,SO2 exposure was associated with a significant decrease in progressive motility(PC=0.032;95%CI:-0.063 to-0.001;P=0.044)and sperm concentration(PC=-0.020;95%CI:-0.036 to-0.005;P=0.012).However,no statistically significant associations were observed for total sperm count(PC=-0.038;95%CI:-0.079 to 0.003;P=0.070),seminal fluid volume(PC=-0.009;95%CI:-0.048 to-0.030;P=0.662)and sperm motility(PC=-0.17;95%CI:-0.363 to 0.022;P=0.830).In addition,the results of the subgroup analysis revealed specific variables that were associated with the decrease in relevant sperm parameters.Conclusions:This systematic review and meta-analysis provides compelling evidence supporting a consistent negative association between exposure to ambient SO2 and semen quality parameters.

Copper slag assisted coke reduction of phosphogypsum for sulphur dioxide preparation

The reduction of phosphogypsum(PG)to lime slag and SO_(2)using coke can effectively alleviate the environmental problems caused by PG.However,the PG decomposition temperature remains high and the product yield remains poor.By adding additives,the decomposition temperature can be further reduced and PG decomposition rate and product yield can be improved.However,the use of current additives such as Fe_(2)O_(3)and SiO_(2)brings the problem of increasing economic cost.Therefore,it is proposed to use solid waste copper slag(CS)as a new additive to reduce PG to prepare SO2,which can reduce the cost and meet the environmental benefits at the same time.The effects of proportion,temperature and thermostatic time on PG decomposition are investigated by experimental and kinetic analysis combined with FactSage thermodynamic calculations to optimize the roasting conditions.Finally,the reaction mechanism is proposed.It is found that adding CS to the coke and PG system can increase the rate of PG decomposition and SO_(2)yield while lowering the PG decomposition temperature.For example,when the CS/PG mass ratio increases from 0 to 1,PG decomposition rate increases from 83.38%to 99.35%,SO_(2)yield increases from 78.62%to 96.81%,and PG decomposition temperature decreases from 992.4℃to 949.6℃.The optimal reaction parameters are CS/PG mass ratio of 1,Coke/PG mass ratio of 0.06 at 1100℃for 20 min with 99.35%PG decomposition rate and 96.81%SO_(2) yield.The process proceeds according to the following reactions:2CaSO_(4)+ 0.7C + 0.8Fe_(2)SiO_(4)→0.8Ca_(2)SiO_(4)+ 0.2Ca_(2)Fe_(2)O_(5)+ 0.4Fe_(3)O_(4)+2SO_(2)+ 0.7CO_(2)Finally,a process for decomposing PG with coke and CS is proposed.

Fine quantitative characterization of high-H2S gas reservoirs under the influence of liquid sulfur deposition and adsorption

In order to clarify the influence of liquid sulfur deposition and adsorption to high-H2S gas reservoirs,three types of natural cores with typical carbonate pore structures were selected for high-temperature and high-pressure core displacement experiments.Fine quantitative characterization of the cores in three steady states(original,after sulfur injection,and after gas flooding)was carried out using the nuclear magnetic resonance(NMR)transverse relaxation time spectrum and imaging,X-ray computer tomography(CT)of full-diameter cores,basic physical property testing,and field emission scanning electron microscopy imaging.The loss of pore volume caused by sulfur deposition and adsorption mainly comes from the medium and large pores with sizes bigger than 1000μm.Liquid sulfur has a stronger adsorption and deposition ability in smaller pore spaces,and causes greater damage to reservoirs with poor original pore structures.The pore structure of the three types of carbonate reservoirs shows multiple fractal characteristics.The worse the pore structure,the greater the change of internal pore distribution caused by liquid sulfur deposition and adsorption,and the stronger the heterogeneity.Liquid sulfur deposition and adsorption change the pore size distribution,pore connectivity,and heterogeneity of the rock,which further changes the physical properties of the reservoir.After sulfur injection and gas flooding,the permeability of TypeⅠreservoirs with good physical properties decreased by 16%,and that of TypesⅡandⅢreservoirs with poor physical properties decreased by 90%or more,suggesting an extremely high damage.This indicates that the worse the initial physical properties,the greater the damage of liquid sulfur deposition and adsorption.Liquid sulfur is adsorbed and deposited in different types of pore space in the forms of flocculence,cobweb,or retinitis,causing different changes in the pore structure and physical property of the reservoir.

Effects of zinc on χ-Fe_(5)C_(2) for carbon dioxide hydrogenation to olefins:Insights from experimental and density function theory calculations

Production of light olefins from CO_(2), the primary greenhouse gases, is of great importance to mitigate the adverse effects of CO_(2) emission on environment and to supply the value-added products from nonpetroleum resource. However, development of robust catalyst with controllable selectivity and stability remains a challenge. Herein, we report that Zn-promoted Fe catalyst can boost the stable and selective production of light olefins from CO_(2). Specifically, the Zn-promoted Fe exhibits a highly stable activity and olefin selectivity over 200 h time-on-stream compared to the unpromoted Fe catalyst, primarily owing to the preservation of active χ-Fe_(5)C_(2) phase. Structural characterizations of the spent catalysts suggest that Zn substantially regulates the content of iron carbide on the surface and suppresses the reoxidation of bulk iron carbide during the reaction. DFT calculations confirm that adsorption of surface carbon atoms and graphene-like carbonaceous species are not thermochemically favored on Zn-promoted Fe catalyst. Carbon deposition by CAC coupling reactions of two surface carbon atoms and dehydrogenation of CH intermediate are also inhibited. Furthermore, the effects of Zn on antioxidation of iron carbide were also investigated. Zn favored the hydrogenation of surface adsorbed oxygen atoms to H_(2)O and the desorption of H_(2)O, which reduces the possibility of surface carbide being oxidized by the chemisorbed oxygen.

Simulation Modelling and Techno-Economics of Supercritical Carbon Dioxide Recompression Closed Brayton Cycle

In recent years, there has been global interest in meeting targets relating to energy affordability and security while taking into account greenhouse gas emissions. This has heightened major interest in potential investigations into the use of supercritical carbon dioxide (sCO2) power cycles. Climate change mitigation is the ultimate driver for this increased interest;other relevant issues include the potential for high cycle efficiency and a circular economy. In this study, a 25 MWe recompression closed Brayton cycle (RCBC) has been assessed, and sCO2 has been proposed as the working fluid for the power plant. The methodology used in this research work comprises thermodynamic and techno-economic analysis for the prospective commercialization of this sCO2 power cycle. An evaluated estimation of capital expenditure, operational expenditure, and cost of electricity has been considered in this study. The ASPEN Plus simulation results have been compared with theoretical and mathematical calculations to assess the performance of the compressors, turbine, and heat exchangers. The results thus reveal that the cycle efficiency for this prospective sCO2 recompression closed Brayton cycle increases (39% - 53.6%) as the temperature progressively increases from 550˚C to 900˚C. Data from the Aspen simulation model was used to aid the cost function calculations to estimate the total capital investment cost of the plant. Also, the techno-economic results have shown less cost for purchasing equipment due to fewer components being required for the cycle configuration as compared to the conventional steam power plant.

Effects of Selenium Dioxide on Apoptosis, Bcl-2 and P53 Expression, Intracellular Reactive Oxygen Species and Calcium Level in Three Human Lung Cancer Cell Lines

Objective: To evaluate the anti-tumor effects of SeO2 and its mechanisms on three human lung cancer cell lines. Methods: Three lung cancer cells A549, GLC-82 and PG were treated with 3-30 μmol/L SeO2. Flow cytometry was used to detect apoptosis, and analyze the changes of expression of p53 and Bcl-2, as well as ROS and Ca2+ level within cells. Results:SeO2 markedly inhibited cell proliferation and viability, and prompted apoptosis after 48 h treatment. SeO2 at 10 μmol/L induced 47.8% apoptosis in A549 cells, 40.8% in GLC-82 cells, 18.2% in PG cells. SeO2 at 30 μmol/L induced 37.8% apoposis in PG cells,but did not increase apoptotic raes in other two cells. SeO2 could down-regulate the mean fluorescent intensity of Bcl-2 from 65.8 to 9.6 in A549, but not in GLC-82 and in PG cells, up-regulate wild type p53 level in all three cells. SeO2 decreased the ROS and Ca2+ level markedly within three tested cells. Conclusion: SeO2 showed anti-tumor effect via apoptosis pathway in three lung cancer cell lines. The decrease of ROS and Ca2+ level within cells as well as regulation of Bcl-2 and p53 expression may play important roles in above apoptotic procedure.

CeO_(2)改性CuO纳米棒协同促进电催化还原CO_(2)制乙烯

随着社会经济发展及人类活动扩大,大气中CO_(2)的浓度日益增加,且带来诸多环境污染问题.因此开发高效、可持续的CO_(2)转化方法至关重要.本文基于电催化反应机理,制备了一系列CuO/CeO_(2)纳米棒复合材料,以促进二氧化碳高选择性还原为C2H_(4).结果表明,经过优化后的CuO/CeO_(2)-2(molCeO_(2):mol_(CuO)=2%)电催化剂在电流密度达到20mA/cm^(2)时,所需电位最低(-0.99V vs.RHE),且对乙烯具有最高的选择性,在电压为-1.08V vs.RHE时,法拉第效率高达46%.此优势可能与大的表面积、更粗糙的表面以及CuO和CeO_(2)之间的协同效应有关,有效提高了反应活性位点和电子转移效率.本研究将为设计和优化CuO基复合材料以实现CO_(2)的高效转化提供理论指导.

SCCO_(2)作用下不同含水性煤孔裂隙结构变化机制

深部煤层封存CO_(2)增产CH_(4)产出过程中,处于超临界状态的CO_(2)(SCCO_(2))与煤中矿物质发生反应,改变煤的孔隙性,进而影响煤层封存CO_(2)的效果和甲烷增产效果。为发现SCCO_(2)–H_(2)O–煤岩作用对煤中孔隙的影响特征,以焦煤为研究对象,开展了不同含水条件下的超临界CO_(2)改造煤实验,基于矿物组成和孔隙性测定结果,对比煤中主要矿物质和不同尺度的孔裂隙变化的差异,探讨了不同含水状态下SCCO_(2)流体对孔裂隙性的作用机制。研究表明:①SCCO_(2)作用后,煤体表面粗糙、疏松,且由于矿物溶蚀使得一些裂隙得到贯通,微裂隙连通性增强。②SCCO_(2)流体对煤具有“扩孔”作用,表现为微、小孔含量下降,中、大孔占比升高,也即微、小孔隙向大孔隙的转化,且孔隙连通性改善;进一步发现,萃余煤吸附孔的分形维数稍微增加,粗糙度增大,而渗流孔的分形维数显著降低,复杂性和非均质性降低。③SCCO_(2)对煤中碳酸盐类矿物的溶解性最好,其次是黏土矿物,且随着含水率增加,萃余煤中的碳酸盐矿物占比先增加后减小。SCCO_(2)使干燥基态、饱和水态煤样中碳酸盐矿物显著溶解,有效改善了孔隙结构,且对饱和水态煤样作用效果更好。空气干燥基态煤样经SCCO_(2)作用后,新生成的白云石矿物聚集在孔喉中造成堵孔效应,缩小原有大孔隙尺寸,是引起不同含水性煤孔隙差异性变化的主要原因。

共沉淀法和浸渍法制备的HoCeMn/TiO_(2)催化剂的脱硝性能

采用浸渍法和共沉淀法制备了HoCeMn/TiO_(2)脱硝催化剂并对其结构和性能进行了表征。结果表明共沉淀法增强了活性组分和载体的相互作用,从而增加了HoCeMnTi-C催化剂表面Ce^(3+)、Mn^(4+)以及吸附氧的含量,使其表现出优异的低温氧化还原性能。此外,共沉淀法制备的HoCeMnTi-C具有更多的表面酸性位点及更强的表面酸性。催化剂表面酸性和氧化还原性能的提高有助于氨的吸附和活化,从而显著提高其活性。表面酸性位点的增多还抑制了H_(2)O和SO_(2)在催化剂表面的吸附,提升了催化剂的抗水抗硫性能。催化剂上的选择性催化还原(SCR)反应遵循Eley-Rideal(E-R)机制,催化剂硫中毒是源于形成的硫酸盐覆盖或破坏了催化剂活性位。

复合催化剂S-CuCo_(2)O_(4)的制备及其活化PMS降解CIP性能研究

采用水热法,以硫脲为硫源对CuCo_(2)O_(4)进行硫化处理合成S-CuCo_(2)O_(4),对复合催化剂S-CuCo_(2)O_(4)进行XRD、FT-IR、SEM、XPS、ICP-OES、EPR表征,并考察其活化过一硫酸盐(PMS)降解环丙沙星(ciprofloxacin,CIP)的效果。实验结果表明:成功制备出S-CuCo_(2)O_(4)催化剂,在其表面富含Co(Ⅱ)和Cu(Ⅰ);当催化剂投加量为0.06 g/L、PMS投加量为0.2 g/L、pH=6.4时,复合催化剂S-CuCo_(2)O_(4)在25 min后对CIP的降解效率可达96.8%,降解效果明显优于CuCo_(2)O_(4)、CuCo_(2)S_(4)。自由基淬灭实验和EPR测试表明,SO_(4)^(-)·和^(1)O_(2)是反应体系的主要活性氧物种,其可能的催化机理是:Cu(Ⅰ)和Co(Ⅱ)能直接与PMS反应生成自由基,同时Cu(Ⅰ)能还原Co(Ⅲ)生成Co(Ⅱ),促进Co(Ⅱ)/Co(Ⅲ)循环,催化剂表面存在的氧空位也可与PMS反应生成^(1)O_(2),在活性氧物种的共同作用下CIP被高效降解。复合催化剂S-CuCo_(2)O_(4)在4次循环使用后对CIP的降解效率仍可达93.5%,证明其循环稳定性较好;对其他污染物也有较好的降解效率,具有较好的通用性,在废水处理中具有良好的应用前景。

药用橡胶塞中可提取硫和4-叔辛基苯酚及2-巯基苯并噻唑的检测

目的建立高效液相色谱法同时测定药用卤化丁基橡胶塞中可提取硫、4-叔辛基苯酚及2-巯基苯并噻唑的含量。方法使用甲苯-甲醇混合溶液作为提取溶剂,采用ZORBAX SB-C_(18)(150 mm×4.6 mm,5μm)色谱柱,流动相为乙腈-水(85:15),流速1.0 mL·min^(-1),检测波长280 nm,柱温为40℃,进样量20μL。结果可提取硫、4-叔辛基苯酚和2-巯基苯并噻唑的检测质量浓度线性范围分别为0.20~501.00μg·mL^(-1)(r=0.9998)、0.20~502.95μg·mL^(-1)(r=0.9999)、0.22~547.53μg·mL^(-1)(r=0.9998),检出限分别为0.40、0.25和0.15μg·mL^(-1);精密度、稳定性的相对标准偏差(RSD)均<3%;提取回收率分别为93.5%~104.8%、99.0%~100.6%和103.0%~107.7%;迁移回收率分别为97.0%~101.8%、98.7%~110.3%和89.3%~94.0%。结论该方法灵敏快速、操作简便、重复性好,可用于药用卤化丁基橡胶塞中可提取硫、4-叔辛基苯酚及2-巯基苯并噻唑含量的测定。

Upregulation of CDGSH iron sulfur domain 2 attenuates cerebral ischemia/reperfusion injury

CDGSH iron sulfur domain 2 can inhibit ferroptosis,which has been associated with cerebral ischemia/reperfusion,in individuals with head and neck cancer.Therefore,CDGSH iron sulfur domain 2 may be implicated in cerebral ischemia/reperfusion injury.To validate this hypothesis in the present study,we established mouse models of occlusion of the middle cerebral artery and HT22 cell models of oxygen-glucose deprivation and reoxygenation to mimic cerebral ischemia/reperfusion injury in vivo and in vitro,respectively.We found remarkably decreased CDGSH iron sulfur domain 2 expression in the mouse brain tissue and HT22 cells.When we used adeno-associated virus and plasmid to up-regulate CDGSH iron sulfur domain 2 expression in the brain tissue and HT22 cell models separately,mouse neurological dysfunction was greatly improved;the cerebral infarct volume was reduced;the survival rate of HT22 cells was increased;HT22 cell injury was alleviated;the expression of ferroptosis-related glutathione peroxidase 4,cystine-glutamate antiporter,and glutathione was increased;the levels of malondialdehyde,iron ions,and the expression of transferrin receptor 1 were decreased;and the expression of nuclear-factor E2-related factor 2/heme oxygenase 1 was increased.Inhibition of CDGSH iron sulfur domain 2 upregulation via the nuclear-factor E2-related factor 2 inhibitor ML385 in oxygen-glucose deprived and reoxygenated HT22 cells blocked the neuroprotective effects of CDGSH iron sulfur domain 2 up-regulation and the activation of the nuclear-factor E2-related factor 2/heme oxygenase 1 pathway.Our data indicate that the up-regulation of CDGSH iron sulfur domain 2 can attenuate cerebral ischemia/reperfusion injury,thus providing theoretical support from the perspectives of cytology and experimental zoology for the use of this protein as a therapeutic target in patients with cerebral ischemia/reperfusion injury.

Regeneration of 2-amino-2-methyl-1-propanol used for carbon dioxide absorption

To improve the efficiency of the carbon dioxide cycling process and to reduce the regeneration energy consumption, a sterically hindered amine of 2-amino-2-methyl-1- propranol （AMP） was investigated to determine its regeneration behavior as a CO2 absorbent. The CO2 absorption and amine regeneration characteristics were experimentally examined under various operating conditions. The regeneration efficiency increased from 86.2% to 98.3% during the temperature range of 358 to 403 K. The most suitable regeneration temperature for AMP was 383 K, in this experiment condition, and the regeneration efficiency of absorption/regeneration runs descended from 98.3% to 94.0%. A number of heat-stable salts （HSS） could cause a reduction in CO2 absorption capacity and regeneration efficiency. The results indicated that aqueous AMP was easier to regenerate with less loss of absorption capacity than other amines, such as, monoethanolamine （MEA）, diethanolamine （DEA）, diethylenetriamine （DETA）, and N-methyldiethanolamine （MDEA）.

750℃高温CO_(2)掺杂SO_(2)环境中Super304H及Inconel625的腐蚀行为

研究掺杂气体对合金的腐蚀行为及作用机理对超临界二氧化碳(supercritical carbon dioxide,S-CO_(2))发电技术具有重要意义。该文开展Super304H及Inconel625合金的高温CO_(2)腐蚀试验,并结合腐蚀增重法、扫描电镜观察及XRD分析,研究两种耐热合金在750℃CO_(2)及掺杂SO_(2)环境中的腐蚀行为。结果表明,两种合金在750℃CO_(2)、750℃CO_(2)+SO_(2)环境中的腐蚀动力学均遵循抛物线规律,Inconel625抗腐蚀能力优于Super304H,具有较少的腐蚀增重;Super304H在750℃CO_(2)腐蚀初期增重高于CO_(2)+SO_(2)环境,而120 h后在CO_(2)+SO_(2)环境中腐蚀增重较高。两种环境中腐蚀500 h后,Super304H表面氧化膜为单层Cr_(2)O_(3)及外层疏松瘤状富铁氧化物与内氧化物FeCr_(2)O_(4)组成的局部双层氧化膜;Inconel625为单层均匀致密Cr_(2)O_(3)氧化膜,平均厚度不到1μm。高温CO_(2)腐蚀环境中,Cr含量对提高合金抗腐蚀性能具有至关重要的作用。高温CO_(2)掺杂SO_(2)对于Cr_(2)O_(3)形成合金具有抑制渗碳的作用,对于氧化铁形成合金具有加速腐蚀及渗碳作用。

Analysis of Sulfur Dioxide Concentration Around Bulk Curing Barn Group

This study was conducted to analyze the spatial distribution of SO2 mass concentration around baking barn groups. A bulk curing barn group was selected as monitoring object, and SO2 concentration around it was monitored for 2 years. The results showed that the SO2 mass concentration within 30-130 m from the baking barn group exceeded the standard, and with the ground as reference, the SO2 mass concentration at the position 0.9-2.1 m from the ground exceeded the stan- dard. According to the limit value of the SO2 mass concentration for sensitive crops, the SO2 mass concentrations over the standard were concentrated within the range of 200-300 m. On the basis of establishment of ＂sulfur control＂, ＂sulfur reduction＂ and ＂sulfur avoiding＂ system, the SO2 emission status of baking barn groups could be improved from the conversion of heat supply method, the utilization of clean en- ergy and adjustment of crop sensitive period and sensitive area.

Control strategy for sulfur dioxide and acid rain pollution in China

Several factors, namely, coal dominated primary energy mix, extensive economic development mode, inefficient energy utilization, and the imperfect environmental regulations, result in the serious urban sulfur dioxide pollution and large scale sulfate type acid precipitation in China. In 1995, China′s sulfur dioxide emissions reached 23.70 Mt, and the areas affected by acid rain accounted for 40% of the territory. Chinese government accords considerable importance to the sulfur dioxide and acid rain contamination. New sets of environmental friendly policies have been promulgated. But enforcement of laws and regulations on SO 2 emissions need to be further improved and broadened, especially those respond to market conditions. This paper focuses particular attention on the analysis of strategy, policies, and national actions which had or should be taken against sulfur dioxide emissions nationwide to achieve the environmental targets, on the basis of which gives the technical options in future.

Defect engineering of high-loading single-atom catalysts for electrochemical carbon dioxide reduction

Electrochemical carbon dioxide reduction reaction(CO_(2)RR)provides an attractive approach to carbon capture and utilization for the production high-value-added products.However,CO_(2)RR still suffers from poor selectivity and low current density due to its sluggish kinetics and multitudinous reaction pathways.Single-atom catalysts(SACs)demonstrate outstanding activity,excellent selectivity,and remarkable atom utilization efficiency,which give impetus to the search for electrocatalytic processes aiming at high selectivity.There appears significant activity in the development of efficient SACs for CO_(2)RR,while the density of the atomic sites remains a considerable barrier to be overcome.To construct high-metal-loading SACs,aggregation must be prevented,and thus novel strategies are required.The key to creating high-density atomically dispersed sites is designing enough anchoring sites,normally defects,to stabilize the highly mobile separated metal atoms.In this review,we summarized the advances in developing high-loading SACs through defect engineering,with a focus on the synthesis strategies to achieve high atomic site loading.Finally,the future opportunities and challenges for CO_(2)RR in the area of high-loading single-atom electrocatalysts are also discussed.

Mechanism explanation for SO_2 oxidation rate of Cs-Rb-V series sulfuric acid catalyst at low temperature

The reaction kinetics of SO 2 oxidation on Cs Rb V series sulfuric acid catalyst promoted by alkali salts such as cesium and rubidium was studied. A three step reaction mechanism of SO 2 oxidation was proposed, in which it was assumed that oxidation of quadrivalent vanadium complex was a controlling step. Then, a mechanism model equation was concluded according to the three step reaction mechanism. The SO 2 oxidation rate was measured with a non gradient reactor under the conditions of temperature of 380～520?℃ and space velocity of 3?600～7?200?h -1 . Through calculating with Powell nonlinear regression method, the parameters of model equation were obtained: K 1=0.152?exp(-62?073/ (RT) ), K 2=8.18?exp(-2?384/ (RT) ), K 3=0.221?exp(-18?949/ (RT) ). It was found that the model equation could fit with all the experimental reaction rate data very well. [

Absorption of sulfur dioxide using membrane and enhancement of desorption with ultrasound

The absorption of sulfur dioxide in simulated flue gas by using liquid-containing membrane was investigated.The process of sulfur dioxide desorption from the absorbent of citrate solution was explored.The influence of the gas-phase,and the liquid-phase on absorption efficiency of sulfur dioxide and the influence of ultrasonic frequency,ultrasonic power and stirring speed on desorption efficiency of sulfur dioxide were examined.The results indicate that the absorption efficiency decreases with increasing flow velocity and sulfur dioxide content in gas-phase,and can be improved by increasing the concentration and the pH value of citrate solution.It is concluded that lower ultrasonic frequency results in a better degassing efficiency.The using of ultrasound in desorbing sulfur dioxide from citrate solution improves the desorbing efficiency in the some conditions,without changing the essence of chemical reaction.