A sulfonated poly(ether ether ketone) (SPEEK) membrane with fairly high degree of sulfonation (DS) swells excessively and even dissolves at high temperature. To solve these problems, sulfonated phenolphthalein p...A sulfonated poly(ether ether ketone) (SPEEK) membrane with fairly high degree of sulfonation (DS) swells excessively and even dissolves at high temperature. To solve these problems, sulfonated phenolphthalein poly(ether sulfone) (SPES-C, DS= 53.7%) is blended with the SPEEK matrix (DS= 55.1%, 61.7%) to prepare SPEEKJSPES-C blend membrane. The decrease in swelling degree and methanol permeability of the membrane is dose-dependent. Pure SPEEK (DS = 61.7%) membrane dissolves completely in water at 70℃, whereas the swelling degree of the SPEEK (DS = 61.7%)/SPES-C (40%, by mass) membrane is 29.7% at 80℃. From room temperature to 80℃, the methanol permeability of all SPEEK (DS = 55.1%)/SPES-C blend membranes is about one order of magnitude lower than that of Nafion 115. At higher temperature, the addition of SPES-C polymer increases the dimensional stability and greater proton conductivity can be achieved. The SPEEK (DS = 55.1%)/SPES-C (40%, by mass) membrane can withstand temperatures up to 150℃. The proton conductivity of SPEEK (DS = 55.1%)/SPES-C (30%, by mass) membrane approaches 0.16 S·cm^-1, matching that of Nafion 115 at 140℃ and 100% RH, while pure SPEEK (DS = 55.1%) membrane dissolves at 90℃. The SPEEK/SPES-C blend membranes are promising for use in direct methanol fuel cells because of their good dimensional stability, high proton conductivity, and low methanol permeability.展开更多
N,N'-Bis(3-hydroxyphenyl)-1,8,4,5-naphthalenetetracarboxylic bisimide was prepared from the reaction of 1,8,4,5-naphthalenetetrcarboxylic acid dianhydride and 2-aminophenol in N, N-dimethylformamide. Polymerization...N,N'-Bis(3-hydroxyphenyl)-1,8,4,5-naphthalenetetracarboxylic bisimide was prepared from the reaction of 1,8,4,5-naphthalenetetrcarboxylic acid dianhydride and 2-aminophenol in N, N-dimethylformamide. Polymerization of this bisimide with 4,4'-difluorodiphenylsulfone and disodium 3,3'-disulfonate4,4'-difluorodiphenylsulfone gave ion-exchange sulfonated poly(ether sulfone). The structure of the title compound was characterized with H-NMR and its polymer was characterized with FT-IR.展开更多
Chloromethylated poly(phthalazinone ether sulfone ketone) (CMPPESK) was prepared from poly(phthalazinone ether sulfone ketone) (PPESK) using chloromethyl octyl ethers (CMOE) with lower toxicity as chlorometh...Chloromethylated poly(phthalazinone ether sulfone ketone) (CMPPESK) was prepared from poly(phthalazinone ether sulfone ketone) (PPESK) using chloromethyl octyl ethers (CMOE) with lower toxicity as chloromethylated regent. CMPPESK was soluble in N-methyl-2-pyrrolidone (NMP), N,N-dimethylacetamide (DMAc) and chloroform. Quaternized poly(phthalazinone ether sulfone ketone) (QAPPESK) was prepared from CMPPESK by quaternization. QAPPESK had excellent solvent resistance, which was only partly soluble in sulfuric acid (98%) and swollen in N,N-dimethylformamide (DMF). The vanadium redox flow battery (V-RFB) using QAPPESK anion-exchange membrane had better performance with 88.3% of overall energy efficiency.展开更多
A sulfonated poly(ether ether ketone) (SPEEK) membrane with a fairly high degree of sulfonation (DS) can swell excessively and even dissolve at high temperature. To solve these problems, insolvable functionalize...A sulfonated poly(ether ether ketone) (SPEEK) membrane with a fairly high degree of sulfonation (DS) can swell excessively and even dissolve at high temperature. To solve these problems, insolvable functionalized silica powder with sulfonic acid groups (SiOx-S) was added into the SPEEK matrix (DS = 55.1%) to prepare SPEEK/ SiOx-S composite membranes. The decrease in both the swelling degree and the methanol permeability of the membranes was a dose-dependent result of addition of the SiOx-S powder. Pure SPEEK membrane swelled 52.6% at 80℃, whereas the SPEEK/SiOx-S (15%, by mass) membrane swelled only 27.3% at the same temperature. From room temperature to 80℃, all SPEEK/SPEEK/SiOx-S composite membranes had methanol permeability of about one order of magnitude lower than that ofNafion115. Compared with pure SPEEK membranes, the addition of the SiOx-S powder not only leads to higher proton conductivity, but also increases the dimensional stability at higher temperatures, and greater proton conductivity can be achieved at higher temperature. The SPEEK/SiO4-S (20%, by mass) membrane could withstand temperature up to 145℃, at which in 100% relative humidity (RH) its proton conductivity exceeded slightly that of Nafion 1 15 membrane and reached 0.17 S·cm^-1, while pure SPEEK membrane dissolved at 90℃. The SPEEK/SiOx-S composite membranes are promising for use in direct methanol fuel cells because of their good dimensional stability, high proton conductivity, and low methanol permeability.展开更多
A novel series of poly(aryl ether sulfone ketone)s (PPESKs) containing phthalazinone and biphenyl moieties were prepared by two-step nucleophilic polycondensation reaction. The ^-Mw values of these copolymers were...A novel series of poly(aryl ether sulfone ketone)s (PPESKs) containing phthalazinone and biphenyl moieties were prepared by two-step nucleophilic polycondensation reaction. The ^-Mw values of these copolymers were between 38,330 and 67,900. The glass transition temperatures (Tg) and 5% decomposition temperatures were ranged in 253-269 ℃ and 488-500 ℃, respectively, The structures of these copolymers were confirmed by FT-IR and ^1H NMR. Moreover, all the resultant copolymers were amorphous determined by wide angle X-ray diffraction (WAXD).展开更多
A novel type of crosslinkable poly(aryl ether sulfone)(PAES) bearing an allyl pendant(PES-OAllyl) was synthesized by a grafting reaction of hydrophenyl-containing PAES(PES-OH) and allyl bromide. PES-OH was pre...A novel type of crosslinkable poly(aryl ether sulfone)(PAES) bearing an allyl pendant(PES-OAllyl) was synthesized by a grafting reaction of hydrophenyl-containing PAES(PES-OH) and allyl bromide. PES-OH was prepared by a demethylation reaction of a methoxyphenylated PAES(PES-OCH3) in the presence of pyridine/hydrochlo- ride. The PES-OCH3 was synthesized by an aromatic nucleophilic substitution of bis(4-chlorophenyl)sulfone and (p-methoxy)phenylhydroquinone. Both DSC and solubility investigation were used to study the crosslinking behavior of PES-OAllyl. After heat treatment, the glass transition temperature(Tg) value of PES-OAllyl sharply increased from 165 ℃ to 227 ℃. Meanwhile, PES-OAllyl changed from a soluble polymer to an insoluble thermoset. In addition, TGA(thermogravimetric analysis) result suggests that the thermal stability of the crosslinked product was improved. All the data prove that the crosslinked PES-OAllyl could be a potential solvent-resistance high-performance material.展开更多
A novel sulfonated poly(arylene ether) containing triphenylmethane moieties was synthesized by the sulfonation of a designed parent polymer using chlorosulfonic acid as sulfonation agent. The sulfonation took place ...A novel sulfonated poly(arylene ether) containing triphenylmethane moieties was synthesized by the sulfonation of a designed parent polymer using chlorosulfonic acid as sulfonation agent. The sulfonation took place at the para position of the pendant phenyl rings because of the specially designed parent polymer. The position and degree of sulfonation were characterized by ^1H-NMR and elemental analysis. The sulfonated polymers are highly soluble in common organic solvents, such as dimethylsulfoxide, N,N'-dimethylacetamide, dimethylformamide, ethylene glycol monomethyl ether, and can be readily cast into tough and smooth films from solutions. The films showed good thermal and hydrolysis stabilities. Moreover, Fenton's reagent test revealed that the films exhibited superior stability to oxidation. The proton conductivities of the films were comparable with Nation 117 under same conditions. The membrane electrode assembly (MEA) prepared with the asmade film (706 EW, 100 μm dry thickness) shows better cell performance than Nation 115-MEA in the whole current density range.展开更多
Proton conducting composite membranes from sulfonated polyether ether ketone and SiO2 for direct methanol fuel cell (DMFC) application were prepared with sulfonated polyether ether ketone(SPEEK) and tetracethoxy s...Proton conducting composite membranes from sulfonated polyether ether ketone and SiO2 for direct methanol fuel cell (DMFC) application were prepared with sulfonated polyether ether ketone(SPEEK) and tetracethoxy silane(TEOS) by sol-gel method. The covalent crosslinking structure was formed between —SO3H of SPEEK via SiO2. The SEM images show that the interfacial compatibility of SPEEK and SiO2 is improved obviously and SiO2 disperses uniformly in the polymer matrix and the particle diameter of SiO2 does not exceed 40 nm. The proton conductivity of composite membranes decreases slightly compared with the SPEEK membrane while the methanol permeability and swelling of composite membrane are improved remarkablely owing to covalent cross-linking between —SO3H and SiO2 .展开更多
A series of Poly(arly ether sulfone ether ketone)s containing pendant methyl groups were synthesized by the reaction of 4,4'-[sulfonylbis (1,4-phenylene)dioxy] dibenzoyl chloride (SODBC) with 4,4'- diphenoxy d...A series of Poly(arly ether sulfone ether ketone)s containing pendant methyl groups were synthesized by the reaction of 4,4'-[sulfonylbis (1,4-phenylene)dioxy] dibenzoyl chloride (SODBC) with 4,4'- diphenoxy diphenylsulfone (DPODPS), 4,4'- di(2-methylphenoxy) diphenylsulfone (o-Me-DPODPS), 4,4'- di(3-methylphenoxy) diphenylsulfone (m-Me-DPODPS), 4,4'- di (2,6-bimethylphenoxy) biphenylsulfone(o-Me2-DPODPS) respectively, in a mixture of 1,2-dichloroethane (DCE) and N-methylpyrrolidone (NMP). These reactions were catalyzed by anhydrous aluminum chloride (AlCl). The characteristic of copolymers were studied by means of advanced analytical techniques such as FT-IR,1H-NMR, DSC, TGA and WAXD. The results show glass transition temperature (Tg) in the range of 193-206℃, thermally stable in excess of 434℃ and excellent solubility in polar solvents. Methyl-substituted Poly(aryl ether sulfone ketone)s had higher glass transition temperatures, lower initial decomposition temperatures than the unsubstituted ones.展开更多
A ternary hybrid membrane architecture consisting of sulfonated fluorinated multi-block copolymer (SFMC), sulfonated (poly ether ether ketone) (SPEEK) and I or 5 wt% graphene oxide (GO) was fabricated through ...A ternary hybrid membrane architecture consisting of sulfonated fluorinated multi-block copolymer (SFMC), sulfonated (poly ether ether ketone) (SPEEK) and I or 5 wt% graphene oxide (GO) was fabricated through a facile solution casting approach. The simple, but effective monomer sulfonation was performed for SFMC to create compact and rigid hydrophobic backbone structures, while conventional random sulfonation was carried-out for SPEEK. Hydrophilic-hydrophobic-hydrophilic structure of SFMC enhances the compatibility with SPEEK and GO and allows for an unprecedented approach to alter me- chanical strength and proton conductivity of ternary hybrid membrane, as verified from universal test machine (UTM) curves and alternating current (AC) impedance plots. The impact of GO integration on the morphology and roughness of hybrid membrane was scrutinized using field emission scanning electron microscope (FE-SEM) and atomic force microscope (AFM). Ternary hybrid showed uniform intercalation of GO nanosheets throughout the entire surface of membrane with an increased surface roughness of 8.91 nm. The constructed ternary hybrid membrane revealed excellent water absorption, ion exchange capacity and gas barrier properties, while retaining reasonable dimensional stability. The well-optimized ternary hybrid membrane containing 5 wt% GO revealed a maximum proton conductivity of 111.9 mS/cm, which is higher by a factor of two-fold with respect to that of bare SFMC membrane. The maximum PEMFC power density of 528.07mW/cm2 was yielded by ternary hybrid membrane at a load current density of 1321.1 mA/cm2 when operating the cell at 70 ℃ under 100% relative humidity (RH). In comparison, a maximum power density of only 182.06 mW/cm2 was exhibited by the bare SFMC membrane at a load current density of 455.56 mA/cm2 under same operating conditions.展开更多
A novel engineering thermoplastic, phenolphthalein poly(ether ether sulfone)(PES C) was blended with a commercial thermotropic liquid crystalline polymer(TLCP), Vectra A950, up to 30 weight percent of TLCP. A rheom...A novel engineering thermoplastic, phenolphthalein poly(ether ether sulfone)(PES C) was blended with a commercial thermotropic liquid crystalline polymer(TLCP), Vectra A950, up to 30 weight percent of TLCP. A rheometrics dynamic spectrometer (RDS Ⅱ) and a CEAST capillary rheometer, a rheoscope 1000 were employed to investigate the melt rheology and extrusion behaviour at both the low and high shearing rates. The morphologies of the blends under different shearing were observed with a scanning electron microscope(SEM) and correlated to the observed rheology. The principal normal stress differences measured with cone and plate geometry give a temperature independent correlation for both blend and PES C when they are plotted against shear stress. But the extrudate swell of the blends showed a strong temperature dependence at each shear stress. The concentration dependence of extrudate swell shows a contrary behaviour to that of the inorganic filled system. A reasonable hypothesis based on the relaxation and disorientation of TLCP during flowing in the capillary and exiting was given to explain it. The melt fracture was checked after extrusion from capillary and was discussed.展开更多
A kind of novel heat-resistant, high performance engineering thermoplastic phthalazinone poly(aryl ether sulfone ketone) (PPESK) containing a carboxyl group in its side chain was prepared by the nucleophilic displacem...A kind of novel heat-resistant, high performance engineering thermoplastic phthalazinone poly(aryl ether sulfone ketone) (PPESK) containing a carboxyl group in its side chain was prepared by the nucleophilic displacement reaction of 4-(4-hydroxylphenyl)- 1 (2H)-phthalazinone with di(4-chlorophenyl) sulfone, 4,4'-difluoro-benzophenone and phenolphthalin in sulfolane in the presence of K2CO3 to produce high molecular weight polymers which can be dissolved in some polar solvents such as chloroform and nitrobenzene at room temperature and can be easily cast into flexible, yellowish and transparent films. PPESK is an amorphous polymer having a decomposition temperature above 400degreesC, which indicates that it has high thermal stability. At the same time, the thermal properties of PPESKs with dicyandiamide (DICY) as curing agent indicated that the heat-resistance properties of the PPESKs are improved after curing. The apparent activation energy (A-E) of the cross-linking reaction and the reaction order (n) of PPESK/DICY were found to be 52.2 kJ/mol and ca. 1.0, respectively. Therefore, the cross-linking reaction is approximately a first order reaction.展开更多
Prolonged hydrothermal treatment for sulfonated poly(ether ether ketone) membranes induces mechanical degradation and developing hydrophilic-hydrophobic phase separation, simultaneously. The enhanced phase separation ...Prolonged hydrothermal treatment for sulfonated poly(ether ether ketone) membranes induces mechanical degradation and developing hydrophilic-hydrophobic phase separation, simultaneously. The enhanced phase separation provides incremental proton conductivity to the membranes, whereas mechanical degradation drastically reduces device stability. On this basis, we describe here the effects of two different ex situ aging processes on sulfonated poly(ether ether ketone) membranes: hydrationdehydration cycling and prolonged hydrothermal treatment. Both aged membranes exhibited enhanced phase separation under the hydrated conditions, as characterized by small angle X-ray scattering.However, when the aged membranes were dried again, the nanostructure of the membranes aged via the hydration-dehydration cycling was recoverable, whereas that of the membranes aged via prolonged hydrothermal treatment was irreversible. Furthermore, the two differently aged membranes showed clear differences in thermal, mechanical, and electrochemical properties. Finally, we implemented both aged membranes in fuel cell application. The sample aged via hydration-dehydration cycling maintained its improved cell performance, whereas the sample aged via hydrothermal treatment showed drastically reduced cell performance after durability test for 50 h.展开更多
A novel poly (ether sulfone ketone) containing the phthalazinone moiety was prepared by the reaction of 4-)4-hydroxyphenyl) (2H) phthalazin-1-one with activated dichloro-monomers. The polymer was characterized by FT-I...A novel poly (ether sulfone ketone) containing the phthalazinone moiety was prepared by the reaction of 4-)4-hydroxyphenyl) (2H) phthalazin-1-one with activated dichloro-monomers. The polymer was characterized by FT-IR, H-1-NMR, DSC, TGA and X-ray diffraction.展开更多
Polyoxometalates(POMs)are classified as solid superacids which can exhibit notable proton conductivity,making them a promising functional inorganic filler for enhancing the proton conductivity of proton exchange membr...Polyoxometalates(POMs)are classified as solid superacids which can exhibit notable proton conductivity,making them a promising functional inorganic filler for enhancing the proton conductivity of proton exchange membranes(PEMs).In this study,a series of hybrid membranes were obtained by molecular-level hybridization of Weakley-type POM Na_(7)H_(2)LaW_(10)O_(36)(LaW_(10))clusters into sulfonated poly(aryl ether ketone sulfone)(SPAEKS).All hybrid membranes exhibited greater proton conductivity than the pristine membrane in the 30–80℃temperature range.When the doping amount of LaW 10 reached 7 wt.%,the proton conductivity of M-LaW 10^(-7)achieved 64 mS·cm^(−1)at 80℃.Lanthanide ions'high coordination number property and variable coordination environment can aid to attract more water molecules from the environment.LaW 10 and these bound water can construct denser hydrogen bonds with–SO_(3)H of SPAEKS.These intensive hydrogen bonds will facilitate the constitution of more continuous proton transport channels,and improve the proton conductivity of the hybrid membrane.This work off ers a fresh approach to using POMs containing rare-earth components in PEMs.展开更多
1, 2-Diliydro-4-(4-hydroxyphenyl)(2H)phthalazin-1-one(DHPZ) was sulfonated in concentrated Sulfuric acid. Poly(phthalazinone ether ketone) containing pendant sodium sulfonate group was synthesized from sulfonated and ...1, 2-Diliydro-4-(4-hydroxyphenyl)(2H)phthalazin-1-one(DHPZ) was sulfonated in concentrated Sulfuric acid. Poly(phthalazinone ether ketone) containing pendant sodium sulfonate group was synthesized from sulfonated and pure 1,2-dihydro-4-(4-hydroxyphenyl)(2H)phthalazin-1-one, and 4,4'-difluorodiphenylketone. The sulfonated monomer and sulfonated polymer were characterized with FT-IR and H-1-NMR.展开更多
Two kinds of macrocyclic oligomers containing aromatic sulfide linkages have been synthesized by the solution polycondensation in high yield. The cyclic compounds were characterized by H-1 and C-13 NMR, by and MALDI -...Two kinds of macrocyclic oligomers containing aromatic sulfide linkages have been synthesized by the solution polycondensation in high yield. The cyclic compounds were characterized by H-1 and C-13 NMR, by and MALDI - TOF MS.展开更多
Evidence from animal experiments has shown that chlorinated polyfluoroalkyl ether sulfonic acids(Cl-PFESAs)can induce vision dysfunction in zebrafish.However,environmental epidemiological evidence supporting this hypo...Evidence from animal experiments has shown that chlorinated polyfluoroalkyl ether sulfonic acids(Cl-PFESAs)can induce vision dysfunction in zebrafish.However,environmental epidemiological evidence supporting this hypothesis remains limited.In our case−control study,samples collected from 270 individuals(135 controls and 135 cases)from the Isomers of C8 Health Project data were analyzed for Cl-PFESAs.We also repeated our analysis on zebrafish to support our findings in humans and to decipher the mechanism underlying Cl-PFESA eye toxicity.The serum levels of per-and polyfluoroalkyl substances(PFASs)and alternatives were significantly higher in the cases than in the controls.Higher serum Cl-PFESA levels were associated with greater odds of eye diseases,and the trend showed a statistically significant dose-dependent relationship.The Shapley additive explanations(SHAP)value indicated that 8:2 Cl-PFESA was the dominant eye disease risk factor among the 13 studied PFASs.In zebrafish experiments,Cl-PFESAs induced eye toxicity in adult zebrafish by oxidative damage and cell apoptosis.Compared to the control group,there was significantly reduced thicknesses of the inner plexiform layer(IPL),outer plexiform layer(OPL),and retinal tissue in the zebrafish exposed to Cl-PFESAs.Our study provides human clinical and animal experimental data,showing that exposure to PFASs increases the odds of the development of eye toxicity.展开更多
A series of multiblock sulfonated poly(arylene ether sulfone)s(SPAES)with various block lengths and predictable ion exchange capacity were synthesized from 4,4’-difluorodiphenyl sulfone,4,4’-dihydrodiphenyl sulfone ...A series of multiblock sulfonated poly(arylene ether sulfone)s(SPAES)with various block lengths and predictable ion exchange capacity were synthesized from 4,4’-difluorodiphenyl sulfone,4,4’-dihydrodiphenyl sulfone and 4,4’-biphenol by one-pot and two-pot polymerization.;H-NMR and FTIR spectra confirmed the structure that sulfonic acid groups were introduced precisely on the poly(arylene ether sulfone)s by post-sulfonation which resulted in controllable sulfonation degree.The proton exchange membranes(PEMs)-based SPAES displayed excellent dimensional,thermal,antioxidant stability,proton conductivity and mechanical properties(maximum tensile stress>35 MPa).Thermogravimetric analysis indicated the prepared SPAES began to degrade above 310℃.The effects of polymerization processes,those were,one-pot hydrophobic segment process,one-pot hydrophilic segment process and two-pot process,on the properties of polymers were investigated.The proton conductivity and microphase separation of SPAES PEMs increased in order of those prepared by one-pot hydrophobic segment process,two-pot process and one-pot hydrophilic segment process.The highest conductivities of SPAES synthesized by the above processes under 80℃ and 100%relative humidity were 213(MS4),297(MB3)and 360 mS·cm^(-1)(MQ2),respectively.展开更多
基金Supported by the State Key Development Program for Basic Research of China (2008CB617502), the National Natural Science Foundation of China (20606025), and Program for Changjiang Scholars and Innovative Research Team in University of China (IRT0641).
文摘A sulfonated poly(ether ether ketone) (SPEEK) membrane with fairly high degree of sulfonation (DS) swells excessively and even dissolves at high temperature. To solve these problems, sulfonated phenolphthalein poly(ether sulfone) (SPES-C, DS= 53.7%) is blended with the SPEEK matrix (DS= 55.1%, 61.7%) to prepare SPEEKJSPES-C blend membrane. The decrease in swelling degree and methanol permeability of the membrane is dose-dependent. Pure SPEEK (DS = 61.7%) membrane dissolves completely in water at 70℃, whereas the swelling degree of the SPEEK (DS = 61.7%)/SPES-C (40%, by mass) membrane is 29.7% at 80℃. From room temperature to 80℃, the methanol permeability of all SPEEK (DS = 55.1%)/SPES-C blend membranes is about one order of magnitude lower than that of Nafion 115. At higher temperature, the addition of SPES-C polymer increases the dimensional stability and greater proton conductivity can be achieved. The SPEEK (DS = 55.1%)/SPES-C (40%, by mass) membrane can withstand temperatures up to 150℃. The proton conductivity of SPEEK (DS = 55.1%)/SPES-C (30%, by mass) membrane approaches 0.16 S·cm^-1, matching that of Nafion 115 at 140℃ and 100% RH, while pure SPEEK (DS = 55.1%) membrane dissolves at 90℃. The SPEEK/SPES-C blend membranes are promising for use in direct methanol fuel cells because of their good dimensional stability, high proton conductivity, and low methanol permeability.
基金This project is supported by the National Natural Science Foundation of China(No.20104001).
文摘N,N'-Bis(3-hydroxyphenyl)-1,8,4,5-naphthalenetetracarboxylic bisimide was prepared from the reaction of 1,8,4,5-naphthalenetetrcarboxylic acid dianhydride and 2-aminophenol in N, N-dimethylformamide. Polymerization of this bisimide with 4,4'-difluorodiphenylsulfone and disodium 3,3'-disulfonate4,4'-difluorodiphenylsulfone gave ion-exchange sulfonated poly(ether sulfone). The structure of the title compound was characterized with H-NMR and its polymer was characterized with FT-IR.
基金partly financed by the Major State Basic Research Development Program of China(No.2003 CB615700)the National Natural Science Foundation of China(No.20604005).
文摘Chloromethylated poly(phthalazinone ether sulfone ketone) (CMPPESK) was prepared from poly(phthalazinone ether sulfone ketone) (PPESK) using chloromethyl octyl ethers (CMOE) with lower toxicity as chloromethylated regent. CMPPESK was soluble in N-methyl-2-pyrrolidone (NMP), N,N-dimethylacetamide (DMAc) and chloroform. Quaternized poly(phthalazinone ether sulfone ketone) (QAPPESK) was prepared from CMPPESK by quaternization. QAPPESK had excellent solvent resistance, which was only partly soluble in sulfuric acid (98%) and swollen in N,N-dimethylformamide (DMF). The vanadium redox flow battery (V-RFB) using QAPPESK anion-exchange membrane had better performance with 88.3% of overall energy efficiency.
基金Supported by the State Key Development Program for Basic Research of China (2008CB617502), the National Natural Science Foundation of China (20606025), and Program for Changjiang Scholars and Innovative Research Team in University of China (IRT0641).
文摘A sulfonated poly(ether ether ketone) (SPEEK) membrane with a fairly high degree of sulfonation (DS) can swell excessively and even dissolve at high temperature. To solve these problems, insolvable functionalized silica powder with sulfonic acid groups (SiOx-S) was added into the SPEEK matrix (DS = 55.1%) to prepare SPEEK/ SiOx-S composite membranes. The decrease in both the swelling degree and the methanol permeability of the membranes was a dose-dependent result of addition of the SiOx-S powder. Pure SPEEK membrane swelled 52.6% at 80℃, whereas the SPEEK/SiOx-S (15%, by mass) membrane swelled only 27.3% at the same temperature. From room temperature to 80℃, all SPEEK/SPEEK/SiOx-S composite membranes had methanol permeability of about one order of magnitude lower than that ofNafion115. Compared with pure SPEEK membranes, the addition of the SiOx-S powder not only leads to higher proton conductivity, but also increases the dimensional stability at higher temperatures, and greater proton conductivity can be achieved at higher temperature. The SPEEK/SiO4-S (20%, by mass) membrane could withstand temperature up to 145℃, at which in 100% relative humidity (RH) its proton conductivity exceeded slightly that of Nafion 1 15 membrane and reached 0.17 S·cm^-1, while pure SPEEK membrane dissolved at 90℃. The SPEEK/SiOx-S composite membranes are promising for use in direct methanol fuel cells because of their good dimensional stability, high proton conductivity, and low methanol permeability.
文摘A novel series of poly(aryl ether sulfone ketone)s (PPESKs) containing phthalazinone and biphenyl moieties were prepared by two-step nucleophilic polycondensation reaction. The ^-Mw values of these copolymers were between 38,330 and 67,900. The glass transition temperatures (Tg) and 5% decomposition temperatures were ranged in 253-269 ℃ and 488-500 ℃, respectively, The structures of these copolymers were confirmed by FT-IR and ^1H NMR. Moreover, all the resultant copolymers were amorphous determined by wide angle X-ray diffraction (WAXD).
基金Supported by the National Natural Science Foundation of China(No.50973040)the Science and Technology Development Plan of Jilin Province, China(No.20090322)
文摘A novel type of crosslinkable poly(aryl ether sulfone)(PAES) bearing an allyl pendant(PES-OAllyl) was synthesized by a grafting reaction of hydrophenyl-containing PAES(PES-OH) and allyl bromide. PES-OH was prepared by a demethylation reaction of a methoxyphenylated PAES(PES-OCH3) in the presence of pyridine/hydrochlo- ride. The PES-OCH3 was synthesized by an aromatic nucleophilic substitution of bis(4-chlorophenyl)sulfone and (p-methoxy)phenylhydroquinone. Both DSC and solubility investigation were used to study the crosslinking behavior of PES-OAllyl. After heat treatment, the glass transition temperature(Tg) value of PES-OAllyl sharply increased from 165 ℃ to 227 ℃. Meanwhile, PES-OAllyl changed from a soluble polymer to an insoluble thermoset. In addition, TGA(thermogravimetric analysis) result suggests that the thermal stability of the crosslinked product was improved. All the data prove that the crosslinked PES-OAllyl could be a potential solvent-resistance high-performance material.
基金This work was financially supported by the National Science Foundation of China (NSFC) (Key project, No. 29734120)the China High-Tech Development 863 Program (No. 2003AA302410)+1 种基金Natural Science Foundation of Guangdong Province (Excellent Team Project, No. 015007)Canton Province Sci & Tech Bureau (Key Strategic Project, No. A1100402) and Guangzhou Sci & Tech Bureau
文摘A novel sulfonated poly(arylene ether) containing triphenylmethane moieties was synthesized by the sulfonation of a designed parent polymer using chlorosulfonic acid as sulfonation agent. The sulfonation took place at the para position of the pendant phenyl rings because of the specially designed parent polymer. The position and degree of sulfonation were characterized by ^1H-NMR and elemental analysis. The sulfonated polymers are highly soluble in common organic solvents, such as dimethylsulfoxide, N,N'-dimethylacetamide, dimethylformamide, ethylene glycol monomethyl ether, and can be readily cast into tough and smooth films from solutions. The films showed good thermal and hydrolysis stabilities. Moreover, Fenton's reagent test revealed that the films exhibited superior stability to oxidation. The proton conductivities of the films were comparable with Nation 117 under same conditions. The membrane electrode assembly (MEA) prepared with the asmade film (706 EW, 100 μm dry thickness) shows better cell performance than Nation 115-MEA in the whole current density range.
文摘Proton conducting composite membranes from sulfonated polyether ether ketone and SiO2 for direct methanol fuel cell (DMFC) application were prepared with sulfonated polyether ether ketone(SPEEK) and tetracethoxy silane(TEOS) by sol-gel method. The covalent crosslinking structure was formed between —SO3H of SPEEK via SiO2. The SEM images show that the interfacial compatibility of SPEEK and SiO2 is improved obviously and SiO2 disperses uniformly in the polymer matrix and the particle diameter of SiO2 does not exceed 40 nm. The proton conductivity of composite membranes decreases slightly compared with the SPEEK membrane while the methanol permeability and swelling of composite membrane are improved remarkablely owing to covalent cross-linking between —SO3H and SiO2 .
基金This work was supported by National Science Foundation of China (No. 20264001 ), National Science Foundation of Jiangxi Province, Innovation Fund for Technology Based Firms of China (No. 06C26213601342).
文摘A series of Poly(arly ether sulfone ether ketone)s containing pendant methyl groups were synthesized by the reaction of 4,4'-[sulfonylbis (1,4-phenylene)dioxy] dibenzoyl chloride (SODBC) with 4,4'- diphenoxy diphenylsulfone (DPODPS), 4,4'- di(2-methylphenoxy) diphenylsulfone (o-Me-DPODPS), 4,4'- di(3-methylphenoxy) diphenylsulfone (m-Me-DPODPS), 4,4'- di (2,6-bimethylphenoxy) biphenylsulfone(o-Me2-DPODPS) respectively, in a mixture of 1,2-dichloroethane (DCE) and N-methylpyrrolidone (NMP). These reactions were catalyzed by anhydrous aluminum chloride (AlCl). The characteristic of copolymers were studied by means of advanced analytical techniques such as FT-IR,1H-NMR, DSC, TGA and WAXD. The results show glass transition temperature (Tg) in the range of 193-206℃, thermally stable in excess of 434℃ and excellent solubility in polar solvents. Methyl-substituted Poly(aryl ether sulfone ketone)s had higher glass transition temperatures, lower initial decomposition temperatures than the unsubstituted ones.
基金supported by the Korea Institute of Energy Technology Evaluation and Planning(KETEP)the Ministry of Trade,Industry&Energy(MOTIE)of the Republic of Korea(No.20164030201070)supported by Basic Science Research Program through the National Research Foundation of Korea(NRF)funded by the Ministry of Science,ICT and future Planning(NRF-2017R1A2B4005230)
文摘A ternary hybrid membrane architecture consisting of sulfonated fluorinated multi-block copolymer (SFMC), sulfonated (poly ether ether ketone) (SPEEK) and I or 5 wt% graphene oxide (GO) was fabricated through a facile solution casting approach. The simple, but effective monomer sulfonation was performed for SFMC to create compact and rigid hydrophobic backbone structures, while conventional random sulfonation was carried-out for SPEEK. Hydrophilic-hydrophobic-hydrophilic structure of SFMC enhances the compatibility with SPEEK and GO and allows for an unprecedented approach to alter me- chanical strength and proton conductivity of ternary hybrid membrane, as verified from universal test machine (UTM) curves and alternating current (AC) impedance plots. The impact of GO integration on the morphology and roughness of hybrid membrane was scrutinized using field emission scanning electron microscope (FE-SEM) and atomic force microscope (AFM). Ternary hybrid showed uniform intercalation of GO nanosheets throughout the entire surface of membrane with an increased surface roughness of 8.91 nm. The constructed ternary hybrid membrane revealed excellent water absorption, ion exchange capacity and gas barrier properties, while retaining reasonable dimensional stability. The well-optimized ternary hybrid membrane containing 5 wt% GO revealed a maximum proton conductivity of 111.9 mS/cm, which is higher by a factor of two-fold with respect to that of bare SFMC membrane. The maximum PEMFC power density of 528.07mW/cm2 was yielded by ternary hybrid membrane at a load current density of 1321.1 mA/cm2 when operating the cell at 70 ℃ under 100% relative humidity (RH). In comparison, a maximum power density of only 182.06 mW/cm2 was exhibited by the bare SFMC membrane at a load current density of 455.56 mA/cm2 under same operating conditions.
文摘A novel engineering thermoplastic, phenolphthalein poly(ether ether sulfone)(PES C) was blended with a commercial thermotropic liquid crystalline polymer(TLCP), Vectra A950, up to 30 weight percent of TLCP. A rheometrics dynamic spectrometer (RDS Ⅱ) and a CEAST capillary rheometer, a rheoscope 1000 were employed to investigate the melt rheology and extrusion behaviour at both the low and high shearing rates. The morphologies of the blends under different shearing were observed with a scanning electron microscope(SEM) and correlated to the observed rheology. The principal normal stress differences measured with cone and plate geometry give a temperature independent correlation for both blend and PES C when they are plotted against shear stress. But the extrudate swell of the blends showed a strong temperature dependence at each shear stress. The concentration dependence of extrudate swell shows a contrary behaviour to that of the inorganic filled system. A reasonable hypothesis based on the relaxation and disorientation of TLCP during flowing in the capillary and exiting was given to explain it. The melt fracture was checked after extrusion from capillary and was discussed.
基金This project was supported by the National Ninth Five-Year-Plan Key Project "The pilot-scale production and the applied development of polyaryl ether concerning phthalazinone moiety" (No. 97-564-01-07).
文摘A kind of novel heat-resistant, high performance engineering thermoplastic phthalazinone poly(aryl ether sulfone ketone) (PPESK) containing a carboxyl group in its side chain was prepared by the nucleophilic displacement reaction of 4-(4-hydroxylphenyl)- 1 (2H)-phthalazinone with di(4-chlorophenyl) sulfone, 4,4'-difluoro-benzophenone and phenolphthalin in sulfolane in the presence of K2CO3 to produce high molecular weight polymers which can be dissolved in some polar solvents such as chloroform and nitrobenzene at room temperature and can be easily cast into flexible, yellowish and transparent films. PPESK is an amorphous polymer having a decomposition temperature above 400degreesC, which indicates that it has high thermal stability. At the same time, the thermal properties of PPESKs with dicyandiamide (DICY) as curing agent indicated that the heat-resistance properties of the PPESKs are improved after curing. The apparent activation energy (A-E) of the cross-linking reaction and the reaction order (n) of PPESK/DICY were found to be 52.2 kJ/mol and ca. 1.0, respectively. Therefore, the cross-linking reaction is approximately a first order reaction.
基金Byoungseok Min of Pohang Accelerator Laboratory for SAXS technical support at 4C beamline.All authors have read the manuscript and agreed to its contents。
文摘Prolonged hydrothermal treatment for sulfonated poly(ether ether ketone) membranes induces mechanical degradation and developing hydrophilic-hydrophobic phase separation, simultaneously. The enhanced phase separation provides incremental proton conductivity to the membranes, whereas mechanical degradation drastically reduces device stability. On this basis, we describe here the effects of two different ex situ aging processes on sulfonated poly(ether ether ketone) membranes: hydrationdehydration cycling and prolonged hydrothermal treatment. Both aged membranes exhibited enhanced phase separation under the hydrated conditions, as characterized by small angle X-ray scattering.However, when the aged membranes were dried again, the nanostructure of the membranes aged via the hydration-dehydration cycling was recoverable, whereas that of the membranes aged via prolonged hydrothermal treatment was irreversible. Furthermore, the two differently aged membranes showed clear differences in thermal, mechanical, and electrochemical properties. Finally, we implemented both aged membranes in fuel cell application. The sample aged via hydration-dehydration cycling maintained its improved cell performance, whereas the sample aged via hydrothermal treatment showed drastically reduced cell performance after durability test for 50 h.
文摘A novel poly (ether sulfone ketone) containing the phthalazinone moiety was prepared by the reaction of 4-)4-hydroxyphenyl) (2H) phthalazin-1-one with activated dichloro-monomers. The polymer was characterized by FT-IR, H-1-NMR, DSC, TGA and X-ray diffraction.
基金financially supported by the National Natural Science Foundation of China(No.22271022)the Natural Science Foundation of Jilin Province(No.YDZJ202201ZYTS342)supported by the China Scholarship Council(CSC No.201802335014).
文摘Polyoxometalates(POMs)are classified as solid superacids which can exhibit notable proton conductivity,making them a promising functional inorganic filler for enhancing the proton conductivity of proton exchange membranes(PEMs).In this study,a series of hybrid membranes were obtained by molecular-level hybridization of Weakley-type POM Na_(7)H_(2)LaW_(10)O_(36)(LaW_(10))clusters into sulfonated poly(aryl ether ketone sulfone)(SPAEKS).All hybrid membranes exhibited greater proton conductivity than the pristine membrane in the 30–80℃temperature range.When the doping amount of LaW 10 reached 7 wt.%,the proton conductivity of M-LaW 10^(-7)achieved 64 mS·cm^(−1)at 80℃.Lanthanide ions'high coordination number property and variable coordination environment can aid to attract more water molecules from the environment.LaW 10 and these bound water can construct denser hydrogen bonds with–SO_(3)H of SPAEKS.These intensive hydrogen bonds will facilitate the constitution of more continuous proton transport channels,and improve the proton conductivity of the hybrid membrane.This work off ers a fresh approach to using POMs containing rare-earth components in PEMs.
基金the National Natural Science Foundation of China for financial support.
文摘1, 2-Diliydro-4-(4-hydroxyphenyl)(2H)phthalazin-1-one(DHPZ) was sulfonated in concentrated Sulfuric acid. Poly(phthalazinone ether ketone) containing pendant sodium sulfonate group was synthesized from sulfonated and pure 1,2-dihydro-4-(4-hydroxyphenyl)(2H)phthalazin-1-one, and 4,4'-difluorodiphenylketone. The sulfonated monomer and sulfonated polymer were characterized with FT-IR and H-1-NMR.
文摘Two kinds of macrocyclic oligomers containing aromatic sulfide linkages have been synthesized by the solution polycondensation in high yield. The cyclic compounds were characterized by H-1 and C-13 NMR, by and MALDI - TOF MS.
基金supported by the National Key Research and Development Program of China(2018YFC1004300,2018YFC1004301,and 2018YFE0106900)the National Natural Science Foundation of China(82173471,82003409,82103823,and 82073503)+1 种基金the Natural Science Foundation of Guangdong Province(2021A1515012212,2021A1515011754,2021B1515020015,2020A1515011131,2019A050510017,2018B05052007,and 2017A090905042)the Guangxi Key Research and Development Plan(GUIKEAB18050024).
文摘Evidence from animal experiments has shown that chlorinated polyfluoroalkyl ether sulfonic acids(Cl-PFESAs)can induce vision dysfunction in zebrafish.However,environmental epidemiological evidence supporting this hypothesis remains limited.In our case−control study,samples collected from 270 individuals(135 controls and 135 cases)from the Isomers of C8 Health Project data were analyzed for Cl-PFESAs.We also repeated our analysis on zebrafish to support our findings in humans and to decipher the mechanism underlying Cl-PFESA eye toxicity.The serum levels of per-and polyfluoroalkyl substances(PFASs)and alternatives were significantly higher in the cases than in the controls.Higher serum Cl-PFESA levels were associated with greater odds of eye diseases,and the trend showed a statistically significant dose-dependent relationship.The Shapley additive explanations(SHAP)value indicated that 8:2 Cl-PFESA was the dominant eye disease risk factor among the 13 studied PFASs.In zebrafish experiments,Cl-PFESAs induced eye toxicity in adult zebrafish by oxidative damage and cell apoptosis.Compared to the control group,there was significantly reduced thicknesses of the inner plexiform layer(IPL),outer plexiform layer(OPL),and retinal tissue in the zebrafish exposed to Cl-PFESAs.Our study provides human clinical and animal experimental data,showing that exposure to PFASs increases the odds of the development of eye toxicity.
基金financially supported by the National Natural Science Foundation of China(No.21306010)。
文摘A series of multiblock sulfonated poly(arylene ether sulfone)s(SPAES)with various block lengths and predictable ion exchange capacity were synthesized from 4,4’-difluorodiphenyl sulfone,4,4’-dihydrodiphenyl sulfone and 4,4’-biphenol by one-pot and two-pot polymerization.;H-NMR and FTIR spectra confirmed the structure that sulfonic acid groups were introduced precisely on the poly(arylene ether sulfone)s by post-sulfonation which resulted in controllable sulfonation degree.The proton exchange membranes(PEMs)-based SPAES displayed excellent dimensional,thermal,antioxidant stability,proton conductivity and mechanical properties(maximum tensile stress>35 MPa).Thermogravimetric analysis indicated the prepared SPAES began to degrade above 310℃.The effects of polymerization processes,those were,one-pot hydrophobic segment process,one-pot hydrophilic segment process and two-pot process,on the properties of polymers were investigated.The proton conductivity and microphase separation of SPAES PEMs increased in order of those prepared by one-pot hydrophobic segment process,two-pot process and one-pot hydrophilic segment process.The highest conductivities of SPAES synthesized by the above processes under 80℃ and 100%relative humidity were 213(MS4),297(MB3)and 360 mS·cm^(-1)(MQ2),respectively.