The current status of nitrogen containing stainless steels at home and aboard has been introduced. The function and existing forms of nitrogen in the stainless steels, influence of nitrogen on mechanical properties an...The current status of nitrogen containing stainless steels at home and aboard has been introduced. The function and existing forms of nitrogen in the stainless steels, influence of nitrogen on mechanical properties and anti-corrosion properties as well as the application of nitrogen containing cast stainless steels were discussed in this paper. It is clear that nitrogen will be a potential and important alloying element in stainless steels. And Argon Oxygen Decarbonization (AOD) refining can provide an advanced manufacture process for nitrogen containing stainless steels with ultra-low- carbon and high cleanliness.展开更多
Stress corrosion cracking （SCC） of stainless steels and Ni-based alloys in high temperature water coolant is one of the key problems affecting the safe operation of nuclear power plants （NPPs）. The nitrogen-added ...Stress corrosion cracking （SCC） of stainless steels and Ni-based alloys in high temperature water coolant is one of the key problems affecting the safe operation of nuclear power plants （NPPs）. The nitrogen-added stainless steel is a kind of possible candidate materials for mitigating SCC since reducing the carbon content and adding nitrogen to offset the loss in strength caused by the decrease in carbon content can mitigate the problem of sensitization. However, the reports of SCC of nitrogen-added stainless steels in high temperature water are few available. The effects of applied potential and sensitization treatment on the SCC of a newly developed nitrogen-containing stainless steel （SS） 316LN in high temperature water doped with chloride at 250 ℃ were studied by using slow strain rate tests （SSRTs）. The SSRT results are compared with our data previously published for 316 SS without nitrogen and 304NG SS with nitrogen, and the possible mechanism affecting the SCC behaviors of the studied steels is also discussed based on SSRT and microstucture analysis results. The susceptibility to cracking of 316LN SS normally increases with increasing potential. The susceptibility to SCC of 316LN SS was less than that of 316 SS and 304NG SS. Sensitization treatment at 700℃ for 30 h showed little effect on the S CC of 316LN S S and significant effect on the S CC of 316 S S. The predominant cracking mode for the 316LN S S in both annealed state and the state after the sensitization treatment was transgranular. The presented conditions of mitigating stress corrosion cracking are some useful information for the safe use of 316LN SS in NPPs.展开更多
The influence of N on the precipitation behavior,associated corrosion,and mechanical properties of S32654 were investigated by microstructural,electrochemical,and mechanical analyses.Increasing the N content results i...The influence of N on the precipitation behavior,associated corrosion,and mechanical properties of S32654 were investigated by microstructural,electrochemical,and mechanical analyses.Increasing the N content results in several alterations:(1) grain refinement,which promotes intergranular precipitation;(2) a linear increase in the driving force for Cr2 N and Mo activity,which accelerates the precipitation of intergranular Cr2 N and π phase,respectively;(3) a linear decrease in the driving force for σ phase and Cr activity,which suppresses the formation of intragranular σ phase.The total amount of precipitates first decreased and then increased with the N content increasing.Furthermore,the intergranular corrosion susceptibility depended substantially on the total amount of precipitates and also first exhibited a decreasing and then an increasing trend as the N content increased.In addition,aging precipitation caused a considerable decrement in the ultimate tensile strength(UTS) and a remarkable increment in the yield strength(YS).Both the UTS and YS always increased with N content increasing throughout the solution and aging process.Whereas the elongation was considerably sensitive to the aging treatment,it exhibited marginal variation with the N content increasing.展开更多
为了扩大不锈钢的应用范围与节省较昂贵的镍资源,笔者以粒径<38.5μm含氮不锈钢粉末和多组元粘结剂(PW,HDPE,SA)为原料,采用粉末注射成形工艺制备了0Cr17Mn12Mo2N含氮无镍奥氏体不锈钢材料,并对其表面状态与显微组织、拉伸断口形貌...为了扩大不锈钢的应用范围与节省较昂贵的镍资源,笔者以粒径<38.5μm含氮不锈钢粉末和多组元粘结剂(PW,HDPE,SA)为原料,采用粉末注射成形工艺制备了0Cr17Mn12Mo2N含氮无镍奥氏体不锈钢材料,并对其表面状态与显微组织、拉伸断口形貌以及力学性能、耐蚀性能进行了分析与测试。结果表明:使用上述粘结剂能够成功地实现含氮不锈钢粉末的注射成形;在流动N2气氛中,0.1MPa,1340℃下烧结120m in,再经热处理后,注射成形0Cr17Mn12Mo2N不锈钢烧结体的相对密度可达到97.6%,含氮量达到0.83%(质量分数)。该含氮无镍不锈钢具有良好的强度和塑性:抗拉强度σb=910MPa,屈服强度σ0.2=560MPa,伸长率5δ=46%,断面收缩率Ф=39.5%,硬度(HRB)为91.7,各项性能指标均优异于M IM 316L不锈钢。展开更多
文摘The current status of nitrogen containing stainless steels at home and aboard has been introduced. The function and existing forms of nitrogen in the stainless steels, influence of nitrogen on mechanical properties and anti-corrosion properties as well as the application of nitrogen containing cast stainless steels were discussed in this paper. It is clear that nitrogen will be a potential and important alloying element in stainless steels. And Argon Oxygen Decarbonization (AOD) refining can provide an advanced manufacture process for nitrogen containing stainless steels with ultra-low- carbon and high cleanliness.
基金supported by National Basic Research Program of China (973 Program, Grant No. 2006CB605005)Shanghai Municipal Committee of Science and Technology of china(Grant No. 005207019,Grant No. 08520708000)
文摘Stress corrosion cracking （SCC） of stainless steels and Ni-based alloys in high temperature water coolant is one of the key problems affecting the safe operation of nuclear power plants （NPPs）. The nitrogen-added stainless steel is a kind of possible candidate materials for mitigating SCC since reducing the carbon content and adding nitrogen to offset the loss in strength caused by the decrease in carbon content can mitigate the problem of sensitization. However, the reports of SCC of nitrogen-added stainless steels in high temperature water are few available. The effects of applied potential and sensitization treatment on the SCC of a newly developed nitrogen-containing stainless steel （SS） 316LN in high temperature water doped with chloride at 250 ℃ were studied by using slow strain rate tests （SSRTs）. The SSRT results are compared with our data previously published for 316 SS without nitrogen and 304NG SS with nitrogen, and the possible mechanism affecting the SCC behaviors of the studied steels is also discussed based on SSRT and microstucture analysis results. The susceptibility to cracking of 316LN SS normally increases with increasing potential. The susceptibility to SCC of 316LN SS was less than that of 316 SS and 304NG SS. Sensitization treatment at 700℃ for 30 h showed little effect on the S CC of 316LN S S and significant effect on the S CC of 316 S S. The predominant cracking mode for the 316LN S S in both annealed state and the state after the sensitization treatment was transgranular. The presented conditions of mitigating stress corrosion cracking are some useful information for the safe use of 316LN SS in NPPs.
基金This work was financially supported by National Natural Science Foundation of China(No.U1860204)the Fundamental Research Funds for the Central Universities(No.N172507002)the Transformation Project of Major Scientific and Technological Achievements in Shenyang(No.Z17-5-003).
文摘The influence of N on the precipitation behavior,associated corrosion,and mechanical properties of S32654 were investigated by microstructural,electrochemical,and mechanical analyses.Increasing the N content results in several alterations:(1) grain refinement,which promotes intergranular precipitation;(2) a linear increase in the driving force for Cr2 N and Mo activity,which accelerates the precipitation of intergranular Cr2 N and π phase,respectively;(3) a linear decrease in the driving force for σ phase and Cr activity,which suppresses the formation of intragranular σ phase.The total amount of precipitates first decreased and then increased with the N content increasing.Furthermore,the intergranular corrosion susceptibility depended substantially on the total amount of precipitates and also first exhibited a decreasing and then an increasing trend as the N content increased.In addition,aging precipitation caused a considerable decrement in the ultimate tensile strength(UTS) and a remarkable increment in the yield strength(YS).Both the UTS and YS always increased with N content increasing throughout the solution and aging process.Whereas the elongation was considerably sensitive to the aging treatment,it exhibited marginal variation with the N content increasing.
文摘为了扩大不锈钢的应用范围与节省较昂贵的镍资源,笔者以粒径<38.5μm含氮不锈钢粉末和多组元粘结剂(PW,HDPE,SA)为原料,采用粉末注射成形工艺制备了0Cr17Mn12Mo2N含氮无镍奥氏体不锈钢材料,并对其表面状态与显微组织、拉伸断口形貌以及力学性能、耐蚀性能进行了分析与测试。结果表明:使用上述粘结剂能够成功地实现含氮不锈钢粉末的注射成形;在流动N2气氛中,0.1MPa,1340℃下烧结120m in,再经热处理后,注射成形0Cr17Mn12Mo2N不锈钢烧结体的相对密度可达到97.6%,含氮量达到0.83%(质量分数)。该含氮无镍不锈钢具有良好的强度和塑性:抗拉强度σb=910MPa,屈服强度σ0.2=560MPa,伸长率5δ=46%,断面收缩率Ф=39.5%,硬度(HRB)为91.7,各项性能指标均优异于M IM 316L不锈钢。
