InSAR-derived surface deformation characteristics and mining subsidence parameters in mountain coal mines

Mining-induced surface deformation disrupts ecological balance and impedes economic progress.This study employs SBAS-InSAR with 107-view of ascending and descending SAR data from Sentinel-1,spanning February 2017 to September 2020,to monitor surface deformation in the Fa’er Coal Mine,Guizhou Province.Analysis on the surface deformation time series reveals the relationship between underground mining and surface shifts.Considering geological conditions,mining activities,duration,and ranges,the study determines surface movement parameters for the coal mine.It asserts that mining depth significantly influences surface movement parameters in mountainous mining areas.Increasing mining depth elevates the strike movement angle on the deeper side of the burial depth by 22.84°,while decreasing by 7.74°on the shallower side.Uphill movement angles decrease by 4.06°,while downhill movement angles increase by 15.71°.This emphasizes the technology's suitability for local mining design,which lays the groundwork for resource development,disaster prevention,and ecological protection in analogous contexts.

Evaluation of Convolutional-Long Short-Term Memory Model in Predicting Surface Displacement of Underground Mines

Surface stability is essential in underground mines health management systems. Unexpected Surface displacement in underground mines could lead to loss of lives, injuries, and economic losses. To reduce or neutralise the adverse effects of surface displacement, it is vital to monitor and accurately predict them and unravel their mechanisms. In recent years, Convolutional Neural Network (CNN) and Long Short-Term Memory (LSTM) have proven effective in predicting complex problems. However, CNN neglects the dynamic dependency of the input in the temporal dimension, which affects surface displacement features. The Convolutional-LSTM model can dynamically learn the temporal dependency among input features via the feedback connections in the LSTM to improve accurate captures of surface displacement features. This study focused on evaluating the C-LSTM model in predicting surface displacement of underground mines and assessed the predictive capabilities and generalisation strength of using hybridised ANN models. Geodetic and geotechnical data gathered from a Gold Mine in Ghana was used. The three models were tested on experimental data collected at Monitoring Scan Point 3. It was observed from the prediction output that all the methods could provide applicable and practical results. However, using indicators like root mean square error (RMSE) and correlation coefficient (R) in assessing the output of the prediction, the C-LSTM had the best prediction output. This study contributes to the advancement of accurate and efficient prediction of surface displacement of underground mines, ultimately enhancing and assisting safety operations.

Comparative study of mining methods for reserves beneath end slope in flat surface mines with ultra-thick coal seams

The paper aims to identify a reasonable method for mining ultra-thick coal seams in an end-slope in surface mine, With a case study of Heidaigou surface coal mine(HSCM), the paper conducted a comparative research on three mining methods, namely Underground Mining Method(UMM), Highwall Mining System(HMS) and Local Steep Slope Mining Method(LSSMM). A model was firstly established to simulate the impact that UMM and HMS exert on monitoring points and surface deformation. The way that stripping and excavation amount varies with different slope angle, and the corresponding end slope stability were analyzed in the mode of LSSMM. Then a TOPSIS model was established by taking into account six indicators such as recovery ratio, technical complexity and adaptability, the impact on surface mining production, production safety and economic benefits. Finally, LSSMM was determined as the best mining method for mining ultra-thick coal seams in end slope in HSCM.

Feasibility study of highwall mining in north surface mine of Yima Coal Corporation, China

Yima Coal Corporation is considering to adopt highwall mining method withauger machine to recover coal from north surface pit that has reached final highwall position. Themajor geomechanical issues associated with auger mining are highwall and pillar stability. Based onthe field investigation and laboratory test results of mechanical parameters, numerical modeling iscarried out to assess the stability of highwall and pillar. Field measurements of highwalldeformation have been used to validate and ensure the confidence for the development of realisticmodels. The results of numerical modeling show that the mining method is feasible for mining theseam of 10 m thickness in north surface coal mine.

Reliability Theory Study of Combined Mining Technology System in Surface Mines

The connection between all the single systems iu combined technology is analysed, and the mine engineering reliability is calculated in any area of the mines using combined technololgy system. The reliability design and distribution method in this system is put forward, thus the basis is set for the decision to raise the total production capability or the surface mines in which the combined system is used.

KEY TECHNOLOGY OF SEMI-CONTINOUS CONVEYOR SYSTEM IN DEEP SURFACE MINE

The key technology of semi-continuous conveyor system decides the successful using of this system. The key technology includes optimal initial building depth of this system,the crusher moving step and the layout of conveyor system are studied, and their calculating models are built up.

Upward surface movement above deep coal mines after closure and flooding of underground workings

After the mass closures of entire coal mine districts in Europe at the end of the last century, a new phenomenon of surface movement was observed—an upward movement.Although most surface movement(i.e., subsidence) occurs in the months and years after mining by the longwall method, surface movement still occurs many decades after mining is terminated.After the closure and flooding of underground excavations and surrounding rock, this movement was reversed.This paper focuses on quantifying the upward movement in two neighboring coal mines(Winterslag and Zwartberg, Belgium).The study is based on data from a remote sensing technique: interferometry with synthetic aperture radar(INSAR).The results of the study show that the rate of upward movement in the decade after closure is about 10 mm/year on average.The upward movements are not linked directly to the past exploitation directly underneath a location.The amounts of subsidence at specific locations are linked mainly to their positions relative to an inverse trough shape situated over the entire mined-out areas and their immediate surroundings.Local features, such as geological faults, can have a secondary effect on the local variation of the uplift.The processes of subsidence and uplift are based on completely different mechanisms.Subsidence is initiated by a caving process, while the process of uplift is clearly linked to flooding.

Production Characteristics and the Control Factors of Surface Wells for Relieved Methane Drainage in the Huainan Mining Area

Based on the production data of a large number of surface drainage wells in the Huainan mining area,the present study shows that four types of typical production characteristics for relieved methane wells are recognized,of which the stable type for production and gas concentration is the most dominate,as determined by a comprehensive study on the volume and concentration of drained gases, as well as the stress changes of rocks influenced by mining.Some influence factors for the productive differences of the drainage wells were also been discussed.The results indicate that protective coal-seam mining has a significant effect on overlying strata,which promotes the development of pores and fractures of coal reservoirs for methane desorption and migration;however,the production and the stability of drainage wells are affected by deformation and damage of the overlying strata.The second distribution of strata stress is caused by mining engineering,and if the stress load is larger than the carrying capacity of the extraction well,the gas production would be influenced by the drainage well that has been damaged by rock movement.Furthermore,the case damage occurs first in the weak, lithologic interface by its special mechanical properties.The stability of drainage wells and the production status are also influenced by the different drilling techniques,uneven distribution of gas concentration,and combination of gob gas and methane from the protected layer.

Surface movement above old coal longwalls after mine closure

Although most subsidence occurs in the months and years after mining by the longwall method, surface movement is still occurring many decades after the mining. The aim of the study is to quantify the long term behavior. Satellite data(radar-interferometry) were analyzed to study an area of about 2 km^2 during the 18 years following the closure of the underground infrastructure and the flooding of the underground workings and rock mass. It was observed that, on average, a residual downward movement took place till 7–12 years after the closure, followed by a clear uplift. However, the first signs of an uplift occurred in certain sub-areas 3–4 years after the closure. Zones within the area studied were identified with either larger or smaller movements. However, the spatial variation of the surface subsidence or uplift could not be directly explained by the characteristics of mining.

Surface movement and deformation characteristics due to high- intensive coal mining in the windy and sandy region

As China＇s energy strategy moving westward, the surface movement and deformation characteristics due to high-intensive coal mining in the windy and sandy region become a research hotspot. Surface movement observation stations were established to monitor movement and deformation in one super-large working face. Based on field measurements, the surface movement and deformation characteristics were obtained, including angle parameters, subsidence prediction parameters, etc. Besides, the angle and subsidence prediction parameters in similar mining areas are summarized; the mechanism of surface movement and deformation was analyzed with the combination of key stratum theory, mining and geological conditions. The research also indicates that compared with conventional working faces, uniform subsidence area of the subsidence trough in the windy and sandy region is larger, the trough margins are relative steep and deformation values present convergence at the margins, the extent of the trough shrink towards the goaf and the influence time of mining activities lasts shorter; the overlying rock movement and breaking characteristics presents regional particularity in the study area, while the single key stratum, thin bedrock and thick sand that can rapidly propagate movement and deformation are the deep factors, contributing to it.

Optimum location of surface wells for remote pressure relief coalbed methane drainage in mining areas

Based on engineering tests in the Huainan coal mining area,we studied alternative well location to improve the performance of surface wells for remote pressure relief of coalbed methane in mining areas.The key factors,affecting location and well gas production were analyzed by simulation tests for similar material.The exploitation results indicate that wells located in various positions on panels could achieve relatively better gas production in regions with thin Cenozoic layers,low mining heights and slow rate of longwall advancement,but their periods of gas production lasted less than 230 days,as opposed to wells in regions with thick Cenozoic layers,greater mining heights and fast rates of longwall advancement.Wells near panel margins achieved relatively better gas production and lasted longer than centerline wells.The rules of development of mining fractures in strata over panels control gas production of surface wells.Mining fractures located in areas determined by lines of compaction and the effect of mining are well developed and can be maintained for long periods of time.Placing the well at the end of panels and on the updip return airway side of panels,determined by lines of compaction and the effect of mining,would result in surface wells for remote pressure relief CBM obtaining their longest gas production periods and highest cumulative gas production.

Genetic Programming Approach for Predicting Surface Subsidence Induced by Mining

The surface subsidence induced by mining is a complex problem, which is related with many complex and uncertain factors. Genetic programming （GP） has a good ability to deal with complex and nonlinear problems, therefore genetic programming approach is propesed to predict mining induced surface subsidence in this article. First genetic programming technique is introduced, second, surface subsidence genetic programming model is set up by selecting its main affective factors and training relating to practical engineering data, and finally, predictions are made by the testing of data, whose results show that the relative error is approximately less than 10%, which can meet the engineering needs, and therefore, this proposed approach is valid and applicable in predicting mining induced surface subsidence. The model offers a novel method to predict surface subsidence in mining.

Exploitation technology of pressure relief coalbed methane in vertical surface wells in the Huainan coal mining area

Exploitation technology of pressure relief coalbed methane in vertical surface wells is a new method for exploration of gas and coalbed methane exploitation in mining areas with high concentrations of gas, where tectonic coal developed. Studies on vertical surface well technology in the Huainan Coal Mining area play a role in demonstration in the use of clean, new energy resources, preventing and reducing coal mine gas accidents and protecting the environment. Based on the practice of gas drainage engineering of pressure relief coalbed methane in vertical surface wells and combined with relative geological and exploration en- gineering theories, the design principles of design and structure of wells of pressure relief coalbed methane in vertical surface wells are studied. The effects of extraction and their causes are discussed and the impact of geological conditions on gas production of the vertical surface wells are analyzed. The results indicate that in mining areas with high concentrations of gas, where tectonic coal developed, a success rate of pressure relief coalbed methane in surface vertical well is high and single well production usually great. But deformation due to coal exploitation could damage boreholes and cause breaks in the connection between aquifers and bore-holes, which could induce a decrease, even a complete halt in gas production of a single well. The design of well site location and wellbore configuration are the key for technology. The development of the geological conditions for coalbed methane have a significant effect on gas production of coalbed methane wells.

Optimization principle of combined surface and underground mining and its applications

The pit limit optimization is discussed, which is one of the most important problems in the combined min-ing method, on the basis of the economic model of ore-blocks. A new principle of the limit optimization is put for-ward through analyzing the limitations of moving cone method under such conditions. With a view to recovering asmuch mineral resource as possible and making the maximum profit from the whole deposit, the new principle is tomaximize the sum of gain from both open-pit and underground mining. The mathematical models along the horizon-tal and vertical directions and modules for software package (DM&MCAD) have been developed and tested inTonglushan Copper Mine. It has been proved to be rather effective in the mining practice.

GPS and Google Earth based 3D assisted driving system for trucks in surface mines

In order to reduce the number of surface mining accidents related to low visibility conditions and blind spots of trucks and to provide 3D information for truck drivers and real time monitored truck information for the remote dispatcher, a 3D assisted driving system (3D-ADS) based on the GPS, mesh-wireless networks and the Google-Earth engine as the graphic interface and mine-mapping server, was developed at Virginia Tech. The research results indicate that this 3D-ADS system has the potential to increase reliability and reduce uncertainty in open pit mining operations by customizing the local 3D digital mining map, con-structing 3D truck models, tracking vehicles in real time using a 3D interface and indicating available escape routes for driver safety.

Selection of overburden surface mining method in West Virginia by analytical hierarchy process

The broad objective of this research was to improve current surface mining practices and reduce negative environmental impact of overburden removal in West Virginia(WV).The specific objectives were to(i)compare conventional surface mining method(drilling,blasting,digging,and loading)to a surface miner(SM)method,and(ii)apply the analytical hierarchy process(AHP)to help select the optimal mining method based on production,cost and environmental criteria.The design and the procedures used in this research involve five interrelated modules:(i)rock properties of overburden in WV,(ii)drilling and blasting,(iii)digging and loading,(iv)SM method,and(v)comparative analysis and selection of the optimal mining method by AHP.Results of this research indicate that application of SM method would yield higher cost of overburden removal than conventional mining methods in rocks with a high unconfined compressive strength and abrasivity.A significant advantage of SM method,where applicable,is the elimination of the negative environmental impacts associated with blasting.

Surface Mine System Simulation and Safety Risk Management

Modem surface mines, either mono-system or multi-systems, need a large fleet of equipment consisting of excavators, loaders, haulers and auxiliary machines. Presently, the complexity of the system, the interference between sub-systems and the lag in management skills has been a bottle neck for improving productivity of the system. Based on the fact that the traditional tools for safety analysis have been insufficient to evaluate systematically and dynamically the safety risks, this paper tries to create a virtual reality tool consisting of human, machine and mines, using Pro/E and the 3D MAX software in order to evaluate visually the operations of typical mining equipment, such as the bucket wheel excavator （BWE）, the shovel, the truck and the dragline. Within this virtual world, the behavior of the system, such as interaction, interference and potential risk can be replayed and reviewed visually. The objective of the study is to identify the critical safety issues of the system and to provide a convenient and powerful tool for safety training and safety management.

An investigation of surface deformation after fully mechanized,solid back fill mining

The surface deformation after fully mechanized back filling mining was analyzed.The surface deformation for different backfill materials was predicted by an equivalent mining height model and numerical simulations.The results suggest that:(1) As the elastic modulus,E,of the backfill material increases the surface subsidence decreases.The rate of subsidence decrease drops after E is larger than 5 GPa;(2) Fully mechanized back fill mining technology can effectively control surface deformation.The resulting surface deformation is within the specification grade I,which means surface maintenance is not needed.A site survey showed that the equivalent mining height model is capable of predicting and analyzing surface deformation and that the model is conservative enough for engineering safety.Finally,the significance of establishing a complete error correction system based on error analysis and correction is discussed.

Statistical approach to determination of overhaul and maintenance cost of loading equipment in surface mining

The purpose of this research was to develop a new approach in determination of overhaul and maintenance cost of loading equipment in surface mining. Two statistical models including univariate exponential regression (UER) and multivariate linear regression (MLR) were used in this study. Loading equipment parameters such as bucket capacity, machine weight, engine power, boom length, digging depth, and dumping height were considered as variables. The results obtained by models and mean absolute error rate indicate that these models can be applied as the useful tool in determination of overhaul and maintenance cost of loading equipment. The results of this study can be used by the decision-makers for the specific surface mining operations.

A new approach to predicting mining induced surface subsidence

There are many parameters influencing mining induced surface subsidence. These parameters usually interact with one another and some of them have the characteristic of fuzziness. Current approaches to predicting the subsidence cannot take into account of such interactions and fuzziness. In order to overcome this disadvantage, many mining induced surface subsidence cases were accumulated, and an artificial neuro fuzzy inference system(ANFIS) was used to set up 4 ANFIS models to predict the rise angle, dip angle, center angle and the maximum subsidence, respectively. The fitting and generalization prediction capabilities of the models were tested. The test results show that the models have very good fitting and generalization prediction capabilities and the approach can be applied to predict the mining induced surface subsidence.