Effect of Crosslink Structure of Bridge Polycarboxylate Superplasticizers on Dispersion Ability

Bridge polycarboxylate superplasticizers（PCs） with crosslink structure were synthesized by using polyethyleneglycol di-acrylate（PEGdA）, replacing partial polyethyleneglycol mono-acrylate （PEGmA） as crosslinking agent. Structures of bridge PCs were analyzed by gel permeation chromatography, and dispersion ability was evaluated by cement paste dispersity variation on time and rheology test. The experimental results showed that, molecular weight（MW） of bridge PCs increased with increase of PEGdA proportion, and MW distribution curve changed from Gaussian to fiat like, which meant notable increase of highly crosslinked copolymer. Bridge PCs led to decreased initial cement paste dispersity and better dispersity retention due to slow releasing. Further research showed that, PEGdA proportion had slight effect on polymerization degree of backbone, MW distribution of backbone deviated from Gaussian distribution and shoulder peaks appeared on distribution curve when PEGdA increased.

The Compatibility of Polycarboxylate-Type Superplasticizers with Cement

Four polycarboxylate- type （ PC ） superplasticizers of different functional groups were used ; their dispersing and retaining behaviors were analyzed through ZETA potential measurement, mini-slump test of cement paste and performance test of concrete. The experimental results show that the dispersing and flow-retaining ability of PC was determined by two factors of anionic groups and nonionic groups ： the density of anionic groups - COO^- or - SO3^- acted on the electronic repulsive force. and the length and proportion of nonionic graft groups of PEO in PC chemical stracture affected the steric effect. The compatibility between PC superplasticizers and cement mainly depended on the type of PEO groups ; furtlwrmore, adding mineral powders is good to the compatibility for high performance concretes （ HPCs ）.

Influence of Superplasticizers on Strength and Shrinkage Cracking of Cement Mortar under Drying Conditions

The effects of polynaphthalene series superplasticizers（PNS） with a low content of sodium sulfate （H-UNF）,with a high content of sodium sulfate（C-UNF） and polycarboxylate type superplasticizer （PC） on strength and shrinkage cracking of cement mortar under drying conditions were investigated by means of multi-channel ellipse ring shrinkage cracking test, free shrinkage and strength test. The general effect of PNS and PC is to increase the initial cracking time of mortars, and decrease the cracking sensitivity of mortars. As for decreasing the cracking sensitivity of mortars, PC〉H-UNF〉C-UNF. To incorporate superplasticizers is apparently to increase the free shrinkage of mortars when keeping the constant w/b ratio and the content of cement pastes. As for the effect of controlling the volume stability of mortars, PC〉C-UNF〉H-UNF. Maximum crack width of mortars containing PC is lower, but the development rate of maximum crack width of mortars containing H-UNF is faster in comparison with control mortars. The flexural and compressive strengths of mortars at 28-day increase with increasing superplasticizer dosages under drying conditions. PC was superior to PNS in the aspect of increasing strength.

Effect of molecular structure and slump loss resistance of polycarboxylate superplasticizers on self-compacting concrete

A new kind of polycarboxylate superplasticizer with high slump loss resistance was obtained by designing scheduled molecular structure.The number average molecular mass of the polymer was characterized by the gel permeation chromatography measurements.And chemical structure of the polymer was observed by the Fourier transform infrared spectroscopy(FT-IR).The results show that the good workable maintaining of self-compacting concrete could be achieved through direct adjustment of number average molecular mass and different unsaturated monomer in synthetic process.The FT-IR analysis illustrated that the high slump loss resistance of polycarboxylate superplasticizers with ester and carboxyl group and expectations of molecular structure were designed.

Adsorption of Superplasticizers in Fly Ash Blended Cement Pastes and Its Rheological Effects

The adsorption of superplasticizers in fly ash blended cement paste and its rheological effects were investigated.It is shown that the absorption of superplasticizer on portland cement particles is very different from that on fly ash particles.The fly ash particles have smooth surfaces and are negatively charged,so its adsorption capacity is weaker than the portland cement particles.The amount of adsorbed SP in the fly ash blended cement paste depends highly on the replacement proportion of portland cement with fly ash,and to a much less extent on the nature of the fly ash.However,the amount of adsorbed superplasticizer does not correspond well the ζ-potential of the solid particles,due the strong adsorbing capacities of the Portland cement particles.When fly ash replaces portland cement in the paste,the rheological behavior is radically changed,which is closely related to the fineness and density of the ash.The packing and agglomeration of the solid particles are the controlling factors on the rheological parameters of the fresh paste,instead of the amount and type of adsorbed superplasticizer.

Influence of Superplasticizers on Early Age Drying Shrinkage of Cement Paste with the Same Consistency

The influence of superplasticizer（SP） on the early age drying shrinkage of cement paste with the same consistency was investigated. To conduct the test, which lasted for 72 hours, three paste mixtures were used for comparison. The 72 hours early age drying shrinkage staring from the initial setting time was measured by a clock gauge. The pore size distribution was measured by Mercury Intrusion Method. The surface tension of capillary simulation liquid and mass loss of paste were also measured. The experimental results showed that the addition of SP increased the early drying shrinkage greatly. The ratios of water evaporation and the total free water in mixtures added with SPs showed great differences. SPs fined the capillary pores of paste, and the volume of pore with diameter within 50 nm was well consistent with shrinkage rate. The addition of SPs did not raise the capillary liquid surface tension. It showed that with the volume of pore with diameter within 50 nm and the ratio of water evaporation and the total free water a tolerable shrinkage result of paste added with SP could be predicted, and the elastic modulus could have an influence on the early shrinkage. These results have never been proposed before.

Effect of Superplasticizers on the Early Age Hydration of Sulfoaluminate Cement

The effects of two types of superplasticizers on the properties of CSA cement pastes during early hydration were studied. The influences of two types of superplasticizers on the properties of cement pastes, including the normal consistency, setting time, fl uidity, and compressive strength, were investigated by using various methods. The hydration products of the cement pastes cured for 1 day and 3 days were studied by X-ray diffraction（XRD） and scanning electron microscopy（SEM）. The results show that the PCE type superplasticizer retards the early age hydration while the FDN type superplasticizer accelerates the early age hydration of the CSA cement. Both types of superplasticizers have no infl uence on the further hydration of CSA cement, confi rmed by the calorimeter tests as well. The ultrasonic pulse velocity measurements were used to probe the influence of two types of superplasticizers on the hydration of CSA cement pastes at a high water-cement ratio（0.45）. The results show that the PCE type superplasticizer retards the early age hydration of the CSA cement while the FDN type superplasticizer has little infl uence on the early age hydration of the CSA cement.

Chemical Structures and Adsorptive Behaviors of Superplasticizers on β-C_2S

The chemical structures of four types of superplasticizers （SPs） and their adsorptive behaviors on β-C2S were investigated. The adsorption properties of SPs on β-C2S were measured and the relationship between the adsorption quantity and the specific surface of β-C2S was analyzed. The experimental results show that the adsorption quantity increases with the surface area increase of β-C2S, but the adsorption quantity per surface area is similar, which means that the main adsorbent is β-C2S itself. Polycarboxylic ester （PCE） showed the highest adsorption amount on β-C2S, followed by β-naphthalene sulfonates （NSF） and formaldehyde-acetone condensates sulfonates （FAS）, amino sulphonate （AS） showed the least adsorption amount on β-C2S. PCE affected the surface potential of β-C2S particles in water differently in comparison with other types of SPs. The adsorption capacity of SPs on β-C2S is determined by factors such as molecular structure, functional groups and molecular weight of SPs.

Influences of Polycarboxylate Superplasticizers on Rheological Behavior of Low-cement Castables

Influences of different superplasticizers （ STP. KSJSTO and LMS-P） on rheological behavior of low-cement castables and the mechanisms were analyzed. The shear stress and viscosity under different shear rates of matrix slurry were determined using a NXS-I IA rotary viscometer. Effects of different admixtures on the rheological properties of slurry was analyzed theoretically. Sodium tripolyphosphate and poly＇carboxylate superplasticizers KS-JSTO and LMS-P） can improve the fluidity and initial setting time. With STP. the slurry is plastic flow. With KS-JS70 or LMS-P increasing, the slurrv changes from plastic.flow, pseudoplastic flow to dilatant flow successively. Th, e optimum dosages of STP. KS-JSTO and LMS-P are 0. 15%. 0. 25% and 0. 40%, respectively. KS-JS70 and LMS-P can significantly reduce the slurry viscosity and shear stress to improve the workability of construction. Both shear stress and viscosity shall be taken into account for on-site construction.

Influences of Soluble Salts on Adsorption Properties of Polycarboxylate Superplasticizers

Polycarboxylate（PC） superplasticizers with different chemical structures were synthesized through free radical co-polymerization reaction.A total organic carbon analyzer was used to investigate adsorption behaviors of PCs,and to evaluate influences of soluble salts on absorption properties of PCs.It is found that adsorption ratios of PCs on cement particles decrease greatly with the addition of Na2SO4;the adsorption ratio of ethers PC with Hydroxyethyl methacrylate（HEMA） group first increases then decreases with the addition of NaCl;the adsorption ratio of esters PC with short side chains first decreases then increases,while the adsorption ratio of ethers PC with HEMA group decreases with the addition of CaCl2;the adsorption ratio of esters PC with short side chains decreases with the addition of Ca（NO3）2;AlCl3 causes the decrease of the adsorption ratio of ethers PC with HEMA group.

The Effect of Various Polynaphthalene Sulfonate Based Superplasticizers on the Workability of Reactive Powder Concrete

A superplasticizer is a type of chemical admixture used to alter the workability(viscosity)of fresh concrete.The workability of fresh concrete is often of particular importance when the water-to-cement(w/c)ratio is low and a particular workability is desired.Reactive Powder Concrete(RPC)is a high-strength concrete formulated to provide compressive strengths exceeding 130MPa and made of primarily powders.RPC materials typically have a very low w/c,which requires the use of a chemical admixture in order to create a material that is easier to place,handle and consolidate.Superplasticizer are commonly used for this purpose.Superplasticizers are developed from different formulations,the most common being Polycarboxylate Ether(PCE),Polymelamine Sulfonate(PMS),and Polynaphthalene Sulfonate(PNS).This study investigates the effect of various PNS based superplasticizers on the rheological performance and mechanical(compressive strength)performance of a RPC mixture.Six distinctive types of PNS based superplasticizers were used;three of various compositional strengths(high,medium,low range)from a local provider,and three of the same compositional strengths(high,medium,low)from a leading manufacturer.The properties investigated were the individual superplasticizers’viscosity,the concrete workability,determined through a mortar spread test,the concrete viscosity,and the compressive strength of the hardened RPC mixtures measured at 7,14,and 28 days.Two separate RPC mixtures were prepared,which contained two different water-to-cementitious ratios,which consequently increases the dosage of superplasticizer needed,from 34.8L/m3 to 44.7L/m3.The results show that the name brand high range composition produced the overall highest spread,lowest viscosity,and a highest compressive performance.However,the local provider outperformed the name brand in the mid and low range compositions.Lastly,the rheology assessment also confirmed that the name brand high range,and RPC fabricated with the name brand high range,developed the lowest viscosities.

Effects of Mineral Admixtures and Superplasticizers on Micro Hardness of Aggregate-Paste Interface in Cement Concrete

This paper presents quantitatively the results of an experimental investigation on influence of mineral admixtures and superplasticizers on Vickers micro hardness(HV) of aggregate-paste interface in cement concrete. The HV was measured by Vickers hardness testing equipment.The results indicate that addition of fly ash decreases HV of the concrete.Although it decreases with the increase of ground granulated blast furnace slag (GGBS) replacement,the HV is higher than that of concrete containing fly ash at all replacements.The flying ash and GGBS composition increases HV in later curing ages,but does not improve it in early curing ages.Aminosulfonic acid based superplasticizer and aliphatic hydroxy sulphonate condensate superplasticizer can enhance HV in early curing ages.The HV of concrete with polycarboxylic acid superplasticizer is higher in later curing ages.

Influence of High-Robustness Polycarboxylate Superplasticizer on the Performances of Concrete Incorporating Fly Ash and Manufactured Sand

Using ethylene glycol monovinyl polyoxyethylene ether,2-acrylamido-2-methylpropane sulfonic acid(AMPS)and acrylic acid as the main synthetic monomers,a high robustness polycarboxylate superplasticizer was prepared.The effects of initial temperature,ratio of acid to ether,amount of chain transfer agent,and synthesis process on the properties of the superplasticizer were studied.The molecular structure was characterized by GPC(Gel Permeation Chromatography)and IR(Infrared Spectrometer).As shown by the results,when the initial reaction temperature is 15℃,the ratio of acid to ether is 3.4:1 and the acrylic acid pre-neutralization is 15%,The AMPS substitution is 10%,the amount of chain transfer agent is 8%,and the performance of the synthesized superplasticizer is the best.Compared with commercially available ordinary polycarboxylate superplasticizer in C30 concrete prepared with manufactured sand and fly ash,the bleeding rate decreases by 52%,T50 decreases by 1.2 s,and the slump time decreases by 1.1 s.In C60 concrete prepared with fly ash and river sand,the bleeding rate decreases by 46%,T50 decreases by 0.8 s,and the slump time decreases by 3.2 s.

Study on the Hydration and Physical Properties of Cement by M18 Polycarboxylate Superplasticizer Modified Graphene Oxide

Graphene oxide(GO)as a new nano-enhancer in cement-based materials has gained wide attention.However,GO is easy to aggregate in alkaline cement mortar with poor dispersibility.This hinders its application in practical infrastructure construction.In this work,GO-M18 polycarboxylate compound superplasticizer(GM)were obtained by compounding the M18 polycarboxylate superplasticizer with GO solution at different mass ratios.The dispersion of GM in alkaline solution was systematically studied.The phases and functional groups of GM were characterized by XRD and FTIR.The effects of GM on the cement mortar hydration and the formation of microstructure were investigated by measuring the heat of hydration,MIP,TG/DSC,and SEM.The results show that the long-chain structure of the M18 polycarboxylate superplasticizer can increase the interlayer spacing of GO and weaken the force between GO sheets.The modified GO can be uniformly dispersed in the cement slurry.GM can accelerate the early hydration process of cement,which can increase the content of Ca(OH)2 and decrease the grain size.It can optimize the pore size distribution of cement-based materials,increase the density of harmless and less harmful pores,thereby improving mechanical properties.Such methods can transform traditional cement-based materials into stronger,more durable composites,which prolong the life of cement-based materials and reduce the amount of cement used for later maintenance.This provides an idea for achieving sustainability goals in civil engineering.

Achieving high-strain-rate and low-temperature superplasticity in an ECAP-processed Mg-Y-Er-Zn alloy via Ag addition

The effect of adding a small amount of Ag on the microstructure evolution and superplastic properties of Mg-Y-Er-Zn(WEZ612) alloys was systematically studied.The basal texture of the refined WEZ612 alloy produced by equal channel angular pressing was altered to a non-basal structure upon the addition of Ag.Ag addition also refined the grain size and promoted the formation of a large number of nano-14H-long period stacking ordered phases.Using high-resolution transmission electron microscopy,many nano-precipitated phases were detected on the basal plane of the Mg-Y-Er-Zn-1Ag(WEZ612-1Ag) alloy,The nano-precipitated phases on the basal plane improved the thermal stability of the alloy,lowered the deformation activation energy(Q),and improved the stress sensitivity index(m).At 523 K with a strain rate of 10^(-2) s^(-1),the Q value of WEZ612 was higher than that of WEZ612-1Ag(299.14 and 128.5 kJ mol^(-1),respectively).In contrast,the m value of the WEZ612 alloy(0.16) was lower than that of the WEZ612-1Ag alloy(0.46).At 623 K with a tensile rate of 10^(-2) s^(-1),the WEZ612 and WEZ612-1Ag alloys were elongated by 182% and 495%,respectively,with the latter exhibiting high-strain-rate and low-temperature superplasticity.The improved superplasticity of the WEZ612-1Ag alloy is attributed to the nano-precipitated phases,which effectively limit the cavity extension during superplastic deformation.

Preparation of Polycarboxylate-based Superplasticizer and Its Effects on Zeta Potential and Rheological Property of Cement Paste

A series of polycarboxylate-based superplasticizers(PCs) with different structures were synthesized and the effects of chemical structure on zeta potential and rheological property of cement paste were studied. Residual monomers in each sample of PCs were quantitatively determined. The property of the polymers in cement was tested by micro-electrophoresis apparatus and R/S rheometer. Results showed that the zeta potential and its rheological properties are related with the side-chain length and density of PCs. The PCs having shorter side chain and lower side chain density exhibit higher anionic charge density, thus resulting in higher zeta potential. The effect of side chain density on zeta potential is more notable compared with that of side-chain length, and thus affecting the initial shear yield stress and apparent viscosity of the cement paste. In addition, although increasing the side chain length will result in reduction of the anionic charge density, the steric hindrance effect is obvious, which can effectively improve the dispersion of the cement particles, and reduce the viscosity and shear yield stress of slurry.

A Talc-Based Cement-Poor Concrete for Sealing Boreholes in Rock

Deep investigation boreholes in crystalline rock for site selection of repositories for high-level radioactive waste are proposed to be sealed by installing a series of dense concrete and clay plugs. These should prevent radionuclides from leaking canisters at depth to migrate to the biosphere through the holes. The concrete seals will be installed where the holes intersect water-bearing fracture zones to serve as stable and low-permeable supports for adjacent clay plugs. Low porosity and microstructural stability must be guaranteed for many thousands of years and ordinary Portland cement with organic superplastizer will not fulfill the requirements since the high pH will cause degradation of contacting clay and the organic additive can produce colloids with a capacity to carry radionuclides up to the biosphere. Very cement-poor concrete (

The Mitigation of Alkali-Silica Reactions by Aluminum-Bearing Substances

An ability of aluminum-bearing substances-amorphous aluminum hydroxide, aluminum sulphate and basic aluminum sulphate to mitigate alkali-silica reactions in Portland cement mortars has been studied. At equivalent dosages in terms of Al2O3, these substances are ranged in the following order in respect of inhibiting effect: Al(OH)1.78(SO4)0.61 ≥ Al2(SO4)3 > Al(OH)3. It is found that the plasticizing agents of the main types used in cement compositions have no influence on the inhibiting effect of aluminum-bearing admixtures. To control the setting time of cement paste, iron(II) sulphate may be used for partial substitution of Al2SO4·18H2O, and this operation is not influence on the results of ASR expansion test.

Effect of Competitive Adsorption between Sodium Tripolyphosphate and Naphthalene Superplasticizer on Fluidity of Cement Paste

The adsorption amount, ξ-potential of cement particles and fluidity of cement paste were tested to research the competitive adsorption between naphthalene superplasticizer （FDN） and STPP. The experimental results showed that the presence of STPP could significantly improve the fluidity of cement paste and reduce the fluidity loss with FDN. There existed a competitive adsorption between STPP and FDN. STPP and calcium ions formed complexes; they preferentially adsorbed onto surface of cement particles and preempt adsorption points of FDN; and it reduced adsorption amount of FDN. In the absence of STPP, saturation adsorption amount of FDN was 5.93 mg/g; but when the dosage of STPP was 0.1%, it reduced to 4.3 mg/g （about 72.5%）. The adsorption amount of FDN was reduced by STPP, but ξ-potential of cement particles enhanced and fluidity of cement paste increased because of strong negative charge effect of the complexes. Adsorption of the complexes would delay Ca^2＋ into liquid and inhibit formation of active adsorption points. Then, content of FDN in liquid increased with the addition of STPP and ξ-potential of cement particles became stable. In this way, fluidity loss of cement paste reduced.

Hyperbolic Method to Analyze the Electrical Resistivity Curve of Portland Cements with Superplasticizer

Electrical measurement was employed to investigate the early hydration characteristics of cement pastes with different dosages of superplasticizer in the same W/C ratio. The hyperbolic method was applied to analyze the electrical resistivity development. The peak point （Ph） on the hyperbolic curve could be easily read. The time （th） to reach the point Ph had strong relations with the setting time. th was delayed with the increment of the dosage of superplasticizer. The time th was used to plot the relationship between the initial setting time and final setting time. The hyperbolic equation was established to predict the ultimate resistivity. The retardation effect of the superplasticizer was confirmed in the same W/C ratio by setting time and isothermal heat evolution.