Methyl Cholate and Resorcinarene New Carriers for the Recovery of Cr(Ⅲ) Ions by Supported Liquid Membranes (SLM)s

The technique of supported liquid membranes was used to achieve the facilitated transport of Cr(III) ions, using tow amphiphilic carriers, the methyl cholate and resorcinarene. For prepared SLMs, toluene as organic phase and film of polyvinylidene difluoride, as hydrophobic polymer support with 100 μm in thickness and 0.45 μm as the diameter of the pores. The macroscopic parameters (P and J0) on the transport of these ions were determined for different medium temperatures. For these different environments, the prepared SLMs were highly permeable and a clear evolution of these parameters was observed. The parameter J0 depended on the temperature according to the Arrhenius equation. The activation parameters, Ea, ΔH≠ and ΔS≠, for the transition state on the reaction of complex formation (ST) , were determined. To explain these results for this phenomenon, and achieve a better extraction of the substrate, a model based on the substrate complexation by the carrier and the diffusion of the formed complex (ST) was developed. The experimental results verify this model and determine the microscopic parameters (Kass and D*). These studies show that these parameters Kass and D* are specific to facilitated transport of Cr(III) ions by each of the carriers and they are changing significantly with temperature.

Di(2-ethylhexyl) phosphoric acid-coconut oil supported liquid membrane for the separation of copper ions from copper plating wastewater

Permeation of Cu（Ⅱ） from its aqueous solution through a supported liquid membrane （SLM） containing di（2-ethylhexyl）phosphoric acid （D2EHPA） carrier dissolved in coconut oil has been studied. The effects of Cu（Ⅱ）, pH （in feed）, H2SO4 （stripping） and D2EHPA （in membrane） concentrations have been investigated. The stability of the D2EHPA-coconut oil has also been evaluated. High Cu（Ⅱ） concentration in the feed leads to an increase in flux from 4.1 × 10^-9 to 8.9 × 10^-9 mol/（m^2·s） within the Cu（Ⅱ） concentration range 7.8×10^-4-78.6×10^-4 mol/L at pH of 4.0 in the feed and 12.4 × 10^-4 mol/L D2EHPA in the membrane phase. Increase in H2SO4 concentration in strip solution leads to an increase in copper ions flux up to 0.25 mol/L H2SO4, providing a maximum flux of 7.4 × 10^-9 mol/（m^2·s）. The optimum conditions for Cu（Ⅱ） transport are, pH of feed 4.0, 0.25 mol/L H2SO4 in strip phase and 12.4 × 10^-4 mol/L D2EHPA （membrane） in 0.5 μm pore size polytetrafluoroethylene （PTFE） membrane. It has been observed that Cu（Ⅱ） flux across the membrane tends to increase with the concentration of copper ions. Application of the method developed to copper plating bath rinse solutions has been found to be successful in the recovery of Cu（Ⅱ）.

Permeability and Selectivity of Sulfur Dioxide and Carbon Dioxide in Supported Ionic Liquid Membranes

Permeabilities and selectivities of gases such as carbon dioxide （CO2）, sulfur dioxide （SO2）, nitrogen （N2） and methane （CH4） in six imidazolium-based ionic liquids （[emim][BF4], [bmim][BF4], [bmim][PF6], [banim][BF4], [bmim][Tf2N] and [emim][CF3SO3]） supported on polyethersulfone microfiltration membranes are investigated in a single gas feed system using nitrogen as the environment and reference component at temperature from 25 to 45℃ and pressure of N2 from 100 to 400 kPa. It is found that SO2 has the highest permeability in the tested supported ionic liquid membranes, being an order of magnitude higher than that of CO2, and about 2 to 3 orders of magnitude larger than those of N2 and CH4. The observed selectivity of SO2 over the two ordinary gas components is also striking. It is shown experimentally that the dissolution and transport of gas components in the supported ionic liquid membranes, as well as the nature of ionic liquids play important roles in the gas permeation. A nonlinear increase of permeation rate with temperature and operation pressure is also observed for all sample gases. By considering the factors that influence the permeabilities and selectivities of CO2 and SO2, it is expected to develop an optimal supported ionic liquid membrane technology for the isolation of acidic gases in the near future.

Instability Mechanisms of Supported Liquid Membrane for Phenol Transport

The instability mechanisms of the supported liquid membrane using Celgard 2500 membranes as support and tributyl phosphate dissolved in kerosene as carrier for phenol transport was studied by ele.etroehemical impedance spectroscopy. Emulsion formation is demonstrated to be one of the main causes for the instability of supported liquid membrane in the present system. The emulsion-facilitated conditions, such as higher membrane liquid concentration, faster stirring speed, lower salt concentration and higher HLB value, would accelerate the degradation of supported liquid membrane. Other mechanisms including solubility and osmotic pressure work together to increase the membrane liauid loss.

AgBF_4/[emim][BF_4] supported ionic liquid membrane for carbon monoxide/nitrogen separation

In this paper,AgBF_4/[emim][BF_4] supported ionic liquid membranes(SILMs) were prepared successfully for CO/N_2 separation using nitrogen pressure immobilization procedures.The incorporation of AgBF_4 could decrease membrane weight loss,improve the pressure-resistant ability,and keep the critical pressure(0.45 MPa) of the SILMs.The high viscosity and undissolved Ag BF_4 solids in membrane liquid would disturb gas molecular transport through membrane and give rise to the gas transport resistance.Therefore,the gas permeability decreased remarkably with increasing AgBF_4 carrier content in the membrane.When the molar ratio of AgBF_4 to [emim][BF_4] increased from 0:1 to 0.3:1,the CO/N_2 selectivity of the SILMs showed a great increase from ～1 to ～9 at 20 °C and 0.4 MPa,suggesting that AgBF_4 was an effective carrier for CO facilitated transport.The permeabilities of N_2 and CO increased at higher transmembrane pressure,indicating that molecular transport would dominate the transport process at high pressure.The temperature-dependent gas permeability followed the Arrhenius equation.Moreover,the differences between the activation energies of CO and N_2 became larger after introducing AgBF_4,resulting in more obvious decrease in the CO/N_2 selectivity at higher operating temperature.

Enhancing CO_(2) transport with plasma-functionalized ionic liquid membranes

The ionic liquid(IL) 1-butyl-3-methylimidazolium tetrafluoroborate treated with radiofrequency plasma is proposed for functionalization and immobilization on polyethersulfone supports to form supported ionic liquid membranes for CO_(2) separation.The effects of treatment time and transmembrane pressure difference on CO_(2) permeance were evaluated.The best gas permeation performance was obtained with a treatment time of 10 min and the transmembrane pressure difference was 0.25 MPa.Characterization of the materials by Fourier transform infrared spectroscopy,x-ray photoelectron spectroscopy and nuclear magnetic resonance spectroscopy demonstrates that the IL is grafted with carboxyl groups and deprotonated through plasma treatment.A preliminary mechanism for the plasma treatment and facilitated transport of CO_(2)has been proposed on this basis.

Transport Study of Cu （Ⅱ） Through Hollow Fiber Supported Liquid Membrane

The transport of Cu(II)from aqueous solutions containing buffer media through hollow fiber supported liquid membrane(HFSLM)using di(2-ethylhexyl)phosphoric acid(D2EHPA)dissolved in kerosene as membrane phase and hydrochloric acid as striping phase was investigated.A set of factors were studied,including tube side velocity,shell side velocity,pH of the feed phase,Cu(II)concentration in the feed phase,buffer media concentration and D2EHPA concentration in the membrane phase.Experimental results indicate that the mass transfer coefficient increases with increasing both carrier concentration in the organic phase and flow rates on the tube side and shell side,and decreases with increasing initial Cu(II)concentration in the feed phase.With increasing pH value and acetate concentration in the feed phase,the mass transfer coefficient reaches a maximum value then decreases.The optimal operating conditions are obtained at pH value of 4.44 and 0.1 mol·L -1 acetic ion concentration in feed phase,and carrier volume fraction of around 10%in kerosene as organic phase.A mathematical model of the transport mechanism through HFSLM is developed.The modeled results agree well with the experimental ones.

Recovery of Copper Ions from Wastewater by Hollow Fiber Supported Emulsion Liquid Membrane

Recovery of copper ions from wastewater using a hollow fiber supported emulsion liquid membrane (HFSELM) was studied with LIX984N as carrier, kerosene as diluents, and sulfuric acid solution as stripping phase. Effects of compositions of feed and emulsion liquid phase, flow rates on both sides of membrane, and hollow fiber module parameters were investigated. The stability of the emulsion liquid phase without surfactant and the effect of buffer in the feed phase on the extraction rate were also evaluated. It is found that the stability of the emulsion phase without surfactant is poor. Higher flow velocity gives shorter residence time for the emulsion liquid phase on the tube side, reducing the effect of particle coalescence on the separation process. The extraction rate increases with the increase of feed phase pH, carrier concentration, hydrogen ion concentration in the stripping phase, and ef- fective hollow fiber area. The phase ratio in the emulsion liquid phase has a negative effect on extraction rate. The flow rates on both sides have little influence on the extraction performance of the HFSELM, while buffer addition in the feed solution improves the extraction efficiency.

Tb(III) Transport in Dispersion Supported Liquid Membrane System with D2EHPA as Carrier in Kerosene

The transport of Tb（III） in dispersion supported liquid membrane（DSLM） with polyvinylidene fluoride membrane（PVDF） as the support and dispersion solution including HCl solution as the stripping solution and di（2-ethylhexyl） phosphoric acid（D2EHPA） dissolved in kerosene as the membrane solution, has been studied. The effects of pH value, initial concentration of Tb（III） and different ionic strength in the feed phase, volume ratio of membrane solution to stripping solution, concentration of HCl solution, concentration of carrier, different stripping agents in the dispersion phase on the transport of Tb（III） have also been investigated, respectively. As a result, the optimum transport conditions of Tb（III） were obtained, i.e., the concentration of HCl solution was 4.0 mol/L, the concentration of D2EHPA was 0.16 mol/L, the volume ratio of membrane solution to stripping solution was 30：30 in the dispersion phase and pH value was 4.5 in the feed phase. Ionic strength had no obvious effect on the transport of Tb（III）. Under the optimum conditions, the transport percentage of Tb（III） was up to 96.1% in a transport time of 35 min when the initial concentration of Tb（IIl） was 1.0× 10 -4 mol/L. The diffusion coefficient of Tb（III） in the membrane and the thickness of diffusion layer between feed phase and membrane phase were obtained and the values were 1.82×10 -8 m2/s and 5.61 um, respectively. The calculated results were in good agreement with the literature data.

Study on transport of Dy(Ⅲ) by dispersion supported liquid membrane

The transport of Dy（III） through a dispersion supported liquid membrane （DSLM） consisting of polyvinylidene fluoride membrane （PVDF） as the liquid membrane support and dispersion solution including HCI solution as the stripping solution and 2-ethyl hexyl phosphonic acid-mono-2-ethyl hexyl ester （PC-88A） dissolved in kerosene as the membrane solution, was studied. The effects of pH value, initial concentration of Dy（III） and different ionic strength in the feed phase, volume ratio of membrane solution and stripping solution, concentration of HCl solution, concentration of carrier, different stripping agents in the dispersion phase on transport of Dy（III） were also investigated, respectively. As a result, when the concentration of HCI solution was 4.0 mol/L, concentration of PC-88A was 0.10 mol/L, and volume ratio of membrane solution and stripping solution was 40：20 in the dispersion phase, and pH value was 5.0 in the feed phase, the transport effect of Dy（III） was the best. Ionic strength had no obvious effect on transport of Dy（III）. Under the optimum condition studied, when initial concentration of Dy（III） was 0.8×10^-4 mol/L, the transport rate of Dy（III） was up to 96.2% during the transport time of 95 rain. The kinetic equation was developed in terms of the law of mass diffusion and the theory of interface chemistry. The diffusion coefficient of Dy（III） in the membrane and the thickness of diffusion layer between feed phase and membrane phase were obtained and the values were 1.99×10^-7 m^2/s and 15.97 μm, respectively. The results were in good agreement with experimental results.

Supported liquid membrane extraction to treat coal gasification wastewater containing high concentrations phenol

The hollow fiber supported liquid membrane extraction was introduced to treat coal gasification wastewater to recover phenolic compounds,with tributyl phosphate (TBP) as carrier,kerosene as the membrane solvent,sodium hydroxide solution as the stripping agent and PVDF as the membrane material. Factors having strong impact on the extraction efficiency were studied in detail,including the mass transfer mode,twophase flow rate,stripping phase concentration. As extraction system with 20% TBP-kerosene,parallel flow mass transfer,stripping phase concentration 0.1 mol/L,the optimal operating conditions could be obtained. Under the optimum operating conditions,the time required to reach equilibrium for the extraction is 50 min, and extraction efficiency of phenol is 86. 2% and the phenol concentration of effluent is 98.64 mg/L.

Germanium transport across supported liquid membrane with Cyanex 923: Mathematical modeling

A mathematical model was developed to monitor the facilitated transport of germanium(IV) from oxalic acid solutions through a flat sheet supported liquid membrane(FSSLM) containing four trialkylphosphine oxides(Cyanex 923). The FSSLM modeling was based on the extraction constant(Kext) calculated from the liquid-liquid extraction(LLX) modeling. The LLX model presented a reliable calculation of the extraction constant(Kex= 2.057×103 L/mol4). The FSSLM model was solved using Matlab■ software according to extraction constant, Fick’s law, and diffusional principles. The model predicts the overall mass transfer coefficient(Korg) to be 3.84 cm/s. Using this value, diffusion coefficients(Dm) for various Cyanex 923 concentrations of 0.126, 0.252, 0.378, 0.505, 0.631 and 0.757 mol/L are found to be 8.50×10^-4, 4.30×10^-4, 1.87×10^-4, 5.87×10^-5, 2.57×10^-5, 2.09×10^-5 cm2/s, respectively. The results show that the diffusion rate of the current study is approximately more than that of similar FSSLM systems containing Cyanex 923 used to transport various metals. The modeling values are in good agreement with the experimental data, showing the good reliability of the mathematical model.

La(Ⅲ) Transport in Dispersion Supported Liquid Membrane Including PC-88A as the Carrier and HCl Solution as the Stripping Solution

The transport of La(III) through a dispersion supported liquid membrane with polyvinylidene fluoride membrane as the liquid membrane support and dispersion solution including HCl solution as the stripping solution and 2-ethylhexyl phosphonic acid mono-2-ethylhexyl ester (PC-88A) in kerosene as the membrane solution, was studied. As a result, the optimum transport conditions of La(Ⅲ) were obtained as that concentration of HCl solution was 4.0 mol/L, concentration of PC-88A 0.16 mol/L, and volume ratio of membrane to stripping solution 30:30 in the dispersion phase, and pH value 4.0 in the feed phase. Ionic strength had no obvious effect on the transport of La(Ⅲ). Under the optimum conditions, when initial concentration of La(Ⅲ) was 0.8×10-4 mol/L, the transport rate was up to 96.3% during the transport time of 125 min. The kinetic equation was developed based on the law of mass diffusion and theory of interface chemistry. The diffusion coefficient of La(Ⅲ) in the membrane and the thickness of diffusion layer between feed and membrane phases were obtained as 3.20×10-7 m2/s and 3.22×10-5 m, respectively. The calculated results were in good agreement with experimental results.

Supported Liquid Membrane Extraction Technology and Its Application in Detection of Meat Security

As a novel technology,supported liquid membrane extraction has gradually become the direction of the research of extraction,for the advantages of using little organic solvents,good selectivity and repeatability.This paper is based on describing the working principle,structure and infiuencing factors of supported liquid membrane,and research in domestic and foreign literatures which are in the same period, and give a review on the application of supported liquid membrane in meat security determination.

Transport of yttrium metal ions through fibers supported liquid membrane solvent extraction

A novel idea of transport of yttrium(Ⅲ) metal ions through fibers supported liquid membrane in two stage processes namely source to membrane and membrane to receiving phase has been proposed.The fibers supported liquid membrane was impregnated with different concentrations carrier.The experimental variables explored were concentration of yttrium(Ⅲ) ions,pH of source phase,PC-88A concentration in membrane phase,acid concentration in receiving phase and stirring speed.The pre-concentration of yttrium(Ⅲ) ions ...

Study on a Novel Disphase Supplying Supported Liquid Membrane for Transport Behavior of Divalent Nickel Ions

A novel d!sphase supplying supported liquid membrane （DSSLM）, containing supplying feed phase andsupplying stripping phase tor transport behavior ot NI（Ⅱ）, have been studied. The supplying supported feed phase included feed solution and di（2-ethyhexyl） phosphoric acid （HDEHP） as the carrier in kerosene, and supplying stripping phase included HDEHP as the cartier in kerosene and HC1 as the stripping agent. The effects of volume ratio of membrane solution to feed solution （O/F）, pH, initial concentration of Ni（Ⅱ） and ionic strength in the feedsolution, volume ratio of membrane solution to stripping solution （O/S）, concentration of H2SO4 solution, HDEHP concentration in the supplying stripping phase on transport of Ni（/I）, the advantages of DSSLM compared to the traditional supported liquid membrane （SLM）, the system stability, the reuse of membrane solution and the reten- tion of membrane phase were studied. Experimental results indicated that the optimum transpgrt of Ni（Ⅱ） was oh-tained when H2SO4 concentration was 2.00 mol＇L-＇, HDEHP concentration was 0.120 mol·L-1, and O/S was 4· 1 in the supplying stripping phase, O/F was 1 ： 10 and pH was 5.20 in the supplying feed phase. The ionic strength in supplying feed phase had no obvious effect on transport of Ni（Ⅱ）. When initial Ni（Ⅱ） concentration was 2.00x 10-4 mol/L, the transport percentage of Ni（Ⅱ） was up to 93.1% in 250 min. The kinetic equation was deduced in terms of the law of mass diffusion and the interface chemistry.

Hollow Fiber Supported Liquid Membrane for Separation and Recovery of ^152+154Eu and ⁹⁰Sr from Aqueous Acidic Wastes

Separation and recovery of 152+154Eu and 90Sr from radioactive waste using tracer concentration from active material from waste tank in the ET-RR1 Egypt via hollow fiber supported liquid membrane (HFSLM) were achieved. The Polypropylene was used as supporter to carrier 0.5M Cyanex301/kerosene (bis(2,4,4-trimethylpentyl)dithiophosphinic acid and 0.1MEDTA as stripping of 152+154Eu and 90Sr ions from nitrate medium at pH ~3.6. The separation factor was found to be ~4 for 152+154Eu over 90Sr. The aqueous feed of mass transfer coefficient (ki) and the organic mass transfer coefficient (km) were calculated to be (1.52 and 4.5) × 10﹣2cm/s, respectively. In addition, the mass transfer modeling was performed and the validity of the developed model from experimental data was found to join in well with the theoretical values when the Cyanex301 concentration is higher than 1% (v/v). The number of cycles evaluated for complete separation of 152+154Eu and 90Sr is five cycles.

CO_2/N_2 separation using supported ionic liquid membranes with green and cost-effective [Choline][Pro]/PEG200 mixtures

The high price and toxicity of ionic liquids(ILs) have limited the design and application of supported ionic liquid membranes(SILMs) for CO_2 separation in both academic and industrial fields. In this work, [Choline][Pro]/polyethylene glycol 200(PEG200) mixtures were selected to prepare novel SILMs because of their green and costeffective characterization, and the CO_2/N_2 separation with the prepared SILMs was investigated experimentally at temperatures from 308.15 to 343.15 K. The temperature effect on the permeability, solubility and diffusivity of CO_2 was modeled with the Arrhenius equation. A competitive performance of the prepared SILMs was observed with high CO_2 permeability ranged in 343.3–1798.6 barrer and high CO_2/N_2 selectivity from 7.9 to 34.8.It was also found that the CO_2 permeability increased 3 times by decreasing the viscosity of liquids from 370 to38 m Pa·s. In addition, the inherent mechanism behind the significant permeability enhancement was revealed based on the diffusion-reaction theory, i.e. with the addition of PEG200, the overall resistance was substantially decreased and the SILMs process was switched from diffusion-control to reaction-control.

Recent development of ionic liquid membranes

The interest in ionic liquids(IL) is motivated by its unique properties, such as negligible vapor pressure, thermal stability, wide electrochemical stability window, and tunability of properties. ILs have been highlighted as solvents for liquid-liquid extraction and liquid membrane separation. To further expand its application in separation field, the ionic liquid membranes(ILMs) and its separation technology have been proposed and developed rapidly. This paper is to give a comprehensive overview on the recent applications of ILMs for the separation of various compounds, including organic compounds, mixed gases, and metal ions. Firstly, ILMs was classified into supported ionic liquid membranes(SILMs) and quasi-solidified ionic liquid membranes(QSILMs) according to the immobilization method of ILs. Then, preparation methods of ILMs, membrane stability as well as applications of ILMs in the separation of various mixtures were reviewed. Followed this, transport mechanisms of gaseous mixtures and organic compounds were elucidated in order to better understand the separation process of ILMs. This tutorial review intends to not only offer an overview on the development of ILMs but also provide a guide for ILMs preparations and applications.

乳酸萃取支撑液膜的构建及其在乳酸菌液态培养中的应用

利用碱中和解除乳酸胁迫是实现乳酸菌高密度培养的重要方法,但过量的碱也会因渗透压的增加造成菌体死亡。因此,在无渗透胁迫的情况下,原位分离乳酸是解决乳酸抑制的根本方法。该研究评估了利用支撑液膜原位分离乳酸来实现保加利亚乳杆菌sp1.1高密度培养的可行性。首先,利用聚偏二氟乙烯(polyvinylidene difluoride,PVDF)膜作为固体支撑膜,由食品源成分组成的天然低共熔溶剂(natural deep eutectic solvents,NADES)作为载体,NaOH作为接收相,构建了支撑液膜原位萃取系统。结果表明,30%(体积分数)油酸/薄荷醇(体积比2∶1)支撑液膜对保加利亚乳杆菌sp1.1促生长效果最佳,活菌数是未萃取的4.62倍。油酸的羧基与乳酸的羟基或羧基之间的强氢键实现了乳酸的萃取,而薄荷醇则负责稳定NADES。与正常培养相比,支撑液膜萃取乳酸将pH值稳定在4.3以上(完全抑制pH值为4.2),使保加利亚乳杆菌sp 1.1得以持续生长,然而,膜稳定性问题阻碍了保加利亚乳杆菌sp1.1的进一步增殖。NADES萃取系统有望用于乳酸菌的高密度培养。