Di(2-ethylhexyl) phosphoric acid-coconut oil supported liquid membrane for the separation of copper ions from copper plating wastewater

Permeation of Cu（Ⅱ） from its aqueous solution through a supported liquid membrane （SLM） containing di（2-ethylhexyl）phosphoric acid （D2EHPA） carrier dissolved in coconut oil has been studied. The effects of Cu（Ⅱ）, pH （in feed）, H2SO4 （stripping） and D2EHPA （in membrane） concentrations have been investigated. The stability of the D2EHPA-coconut oil has also been evaluated. High Cu（Ⅱ） concentration in the feed leads to an increase in flux from 4.1 × 10^-9 to 8.9 × 10^-9 mol/（m^2·s） within the Cu（Ⅱ） concentration range 7.8×10^-4-78.6×10^-4 mol/L at pH of 4.0 in the feed and 12.4 × 10^-4 mol/L D2EHPA in the membrane phase. Increase in H2SO4 concentration in strip solution leads to an increase in copper ions flux up to 0.25 mol/L H2SO4, providing a maximum flux of 7.4 × 10^-9 mol/（m^2·s）. The optimum conditions for Cu（Ⅱ） transport are, pH of feed 4.0, 0.25 mol/L H2SO4 in strip phase and 12.4 × 10^-4 mol/L D2EHPA （membrane） in 0.5 μm pore size polytetrafluoroethylene （PTFE） membrane. It has been observed that Cu（Ⅱ） flux across the membrane tends to increase with the concentration of copper ions. Application of the method developed to copper plating bath rinse solutions has been found to be successful in the recovery of Cu（Ⅱ）.

Permeability and Selectivity of Sulfur Dioxide and Carbon Dioxide in Supported Ionic Liquid Membranes

Permeabilities and selectivities of gases such as carbon dioxide （CO2）, sulfur dioxide （SO2）, nitrogen （N2） and methane （CH4） in six imidazolium-based ionic liquids （[emim][BF4], [bmim][BF4], [bmim][PF6], [banim][BF4], [bmim][Tf2N] and [emim][CF3SO3]） supported on polyethersulfone microfiltration membranes are investigated in a single gas feed system using nitrogen as the environment and reference component at temperature from 25 to 45℃ and pressure of N2 from 100 to 400 kPa. It is found that SO2 has the highest permeability in the tested supported ionic liquid membranes, being an order of magnitude higher than that of CO2, and about 2 to 3 orders of magnitude larger than those of N2 and CH4. The observed selectivity of SO2 over the two ordinary gas components is also striking. It is shown experimentally that the dissolution and transport of gas components in the supported ionic liquid membranes, as well as the nature of ionic liquids play important roles in the gas permeation. A nonlinear increase of permeation rate with temperature and operation pressure is also observed for all sample gases. By considering the factors that influence the permeabilities and selectivities of CO2 and SO2, it is expected to develop an optimal supported ionic liquid membrane technology for the isolation of acidic gases in the near future.

Instability Mechanisms of Supported Liquid Membrane for Phenol Transport

The instability mechanisms of the supported liquid membrane using Celgard 2500 membranes as support and tributyl phosphate dissolved in kerosene as carrier for phenol transport was studied by ele.etroehemical impedance spectroscopy. Emulsion formation is demonstrated to be one of the main causes for the instability of supported liquid membrane in the present system. The emulsion-facilitated conditions, such as higher membrane liquid concentration, faster stirring speed, lower salt concentration and higher HLB value, would accelerate the degradation of supported liquid membrane. Other mechanisms including solubility and osmotic pressure work together to increase the membrane liauid loss.

Recovery of Copper Ions from Wastewater by Hollow Fiber Supported Emulsion Liquid Membrane

Recovery of copper ions from wastewater using a hollow fiber supported emulsion liquid membrane (HFSELM) was studied with LIX984N as carrier, kerosene as diluents, and sulfuric acid solution as stripping phase. Effects of compositions of feed and emulsion liquid phase, flow rates on both sides of membrane, and hollow fiber module parameters were investigated. The stability of the emulsion liquid phase without surfactant and the effect of buffer in the feed phase on the extraction rate were also evaluated. It is found that the stability of the emulsion phase without surfactant is poor. Higher flow velocity gives shorter residence time for the emulsion liquid phase on the tube side, reducing the effect of particle coalescence on the separation process. The extraction rate increases with the increase of feed phase pH, carrier concentration, hydrogen ion concentration in the stripping phase, and ef- fective hollow fiber area. The phase ratio in the emulsion liquid phase has a negative effect on extraction rate. The flow rates on both sides have little influence on the extraction performance of the HFSELM, while buffer addition in the feed solution improves the extraction efficiency.

Transport Study of Cu （Ⅱ） Through Hollow Fiber Supported Liquid Membrane

The transport of Cu(II)from aqueous solutions containing buffer media through hollow fiber supported liquid membrane(HFSLM)using di(2-ethylhexyl)phosphoric acid(D2EHPA)dissolved in kerosene as membrane phase and hydrochloric acid as striping phase was investigated.A set of factors were studied,including tube side velocity,shell side velocity,pH of the feed phase,Cu(II)concentration in the feed phase,buffer media concentration and D2EHPA concentration in the membrane phase.Experimental results indicate that the mass transfer coefficient increases with increasing both carrier concentration in the organic phase and flow rates on the tube side and shell side,and decreases with increasing initial Cu(II)concentration in the feed phase.With increasing pH value and acetate concentration in the feed phase,the mass transfer coefficient reaches a maximum value then decreases.The optimal operating conditions are obtained at pH value of 4.44 and 0.1 mol·L -1 acetic ion concentration in feed phase,and carrier volume fraction of around 10%in kerosene as organic phase.A mathematical model of the transport mechanism through HFSLM is developed.The modeled results agree well with the experimental ones.

Tb(III) Transport in Dispersion Supported Liquid Membrane System with D2EHPA as Carrier in Kerosene

The transport of Tb（III） in dispersion supported liquid membrane（DSLM） with polyvinylidene fluoride membrane（PVDF） as the support and dispersion solution including HCl solution as the stripping solution and di（2-ethylhexyl） phosphoric acid（D2EHPA） dissolved in kerosene as the membrane solution, has been studied. The effects of pH value, initial concentration of Tb（III） and different ionic strength in the feed phase, volume ratio of membrane solution to stripping solution, concentration of HCl solution, concentration of carrier, different stripping agents in the dispersion phase on the transport of Tb（III） have also been investigated, respectively. As a result, the optimum transport conditions of Tb（III） were obtained, i.e., the concentration of HCl solution was 4.0 mol/L, the concentration of D2EHPA was 0.16 mol/L, the volume ratio of membrane solution to stripping solution was 30：30 in the dispersion phase and pH value was 4.5 in the feed phase. Ionic strength had no obvious effect on the transport of Tb（III）. Under the optimum conditions, the transport percentage of Tb（III） was up to 96.1% in a transport time of 35 min when the initial concentration of Tb（IIl） was 1.0× 10 -4 mol/L. The diffusion coefficient of Tb（III） in the membrane and the thickness of diffusion layer between feed phase and membrane phase were obtained and the values were 1.82×10 -8 m2/s and 5.61 um, respectively. The calculated results were in good agreement with the literature data.

Study on transport of Dy(Ⅲ) by dispersion supported liquid membrane

The transport of Dy（III） through a dispersion supported liquid membrane （DSLM） consisting of polyvinylidene fluoride membrane （PVDF） as the liquid membrane support and dispersion solution including HCI solution as the stripping solution and 2-ethyl hexyl phosphonic acid-mono-2-ethyl hexyl ester （PC-88A） dissolved in kerosene as the membrane solution, was studied. The effects of pH value, initial concentration of Dy（III） and different ionic strength in the feed phase, volume ratio of membrane solution and stripping solution, concentration of HCl solution, concentration of carrier, different stripping agents in the dispersion phase on transport of Dy（III） were also investigated, respectively. As a result, when the concentration of HCI solution was 4.0 mol/L, concentration of PC-88A was 0.10 mol/L, and volume ratio of membrane solution and stripping solution was 40：20 in the dispersion phase, and pH value was 5.0 in the feed phase, the transport effect of Dy（III） was the best. Ionic strength had no obvious effect on transport of Dy（III）. Under the optimum condition studied, when initial concentration of Dy（III） was 0.8×10^-4 mol/L, the transport rate of Dy（III） was up to 96.2% during the transport time of 95 rain. The kinetic equation was developed in terms of the law of mass diffusion and the theory of interface chemistry. The diffusion coefficient of Dy（III） in the membrane and the thickness of diffusion layer between feed phase and membrane phase were obtained and the values were 1.99×10^-7 m^2/s and 15.97 μm, respectively. The results were in good agreement with experimental results.

Germanium transport across supported liquid membrane with Cyanex 923: Mathematical modeling

A mathematical model was developed to monitor the facilitated transport of germanium(IV) from oxalic acid solutions through a flat sheet supported liquid membrane(FSSLM) containing four trialkylphosphine oxides(Cyanex 923). The FSSLM modeling was based on the extraction constant(Kext) calculated from the liquid-liquid extraction(LLX) modeling. The LLX model presented a reliable calculation of the extraction constant(Kex= 2.057×103 L/mol4). The FSSLM model was solved using Matlab■ software according to extraction constant, Fick’s law, and diffusional principles. The model predicts the overall mass transfer coefficient(Korg) to be 3.84 cm/s. Using this value, diffusion coefficients(Dm) for various Cyanex 923 concentrations of 0.126, 0.252, 0.378, 0.505, 0.631 and 0.757 mol/L are found to be 8.50×10^-4, 4.30×10^-4, 1.87×10^-4, 5.87×10^-5, 2.57×10^-5, 2.09×10^-5 cm2/s, respectively. The results show that the diffusion rate of the current study is approximately more than that of similar FSSLM systems containing Cyanex 923 used to transport various metals. The modeling values are in good agreement with the experimental data, showing the good reliability of the mathematical model.

Supported liquid membrane extraction to treat coal gasification wastewater containing high concentrations phenol

The hollow fiber supported liquid membrane extraction was introduced to treat coal gasification wastewater to recover phenolic compounds,with tributyl phosphate (TBP) as carrier,kerosene as the membrane solvent,sodium hydroxide solution as the stripping agent and PVDF as the membrane material. Factors having strong impact on the extraction efficiency were studied in detail,including the mass transfer mode,twophase flow rate,stripping phase concentration. As extraction system with 20% TBP-kerosene,parallel flow mass transfer,stripping phase concentration 0.1 mol/L,the optimal operating conditions could be obtained. Under the optimum operating conditions,the time required to reach equilibrium for the extraction is 50 min, and extraction efficiency of phenol is 86. 2% and the phenol concentration of effluent is 98.64 mg/L.

Transport of Indium, Gallium and Thallium Metal Ions Through Chromatographic Fiber Supported Solid Membrane in Acetylacetone Containing Mixed Solvents

The transport of metal ions of indium, gallium and thallium from source solution to receiving phase through the chromatographic fiber supported solid membrane in the acetylacetone （HAA） containing mixed solvent system has been explored. The fibers supported solid membranes were prepared with chemical synthesis from cellulose fibers and citric acid with the carboxylic acid ion exchange groups introduced. The experimental variables, such as concentration of metal ions （10^-2 to 10^-4 mol.L^-1） in the source solution, mixed solvent composition [for exampl, e, acetylacetone, （2,4-pentanedione）, （HAA） 20% （by volume）, 1,4-dioxane 10% to 60% and HC1 0.25 to 2 mol.L^-1] in the receiving phase and stirring speed （50-130 r.min ） of the bulk source and receiving phase, were explored. The efficiency of mixed solvents for the transport of metal ions from the source to receiving phase through the fiber supported solid membrane was evaluated. The combined ion exchange solvent extraction （CIESE） was observed effective for the selective transport of thallium, indium and gallium metal ions through fiber supported solid membrane in mixed solvents. The oxonium salt formation in the receiving phase enhances thallium, indium and gallium metal ion transport through solid membrane phase. The selective transport of thallium metal ions from source phase was observed from indium and gallium metal ions in the presence of hydrochloric acid in organic solvents in receiving phase. The separation of thallium metal ions from the binary mixtures of Be（II）, Ti（IV）, AI（III） Ca（II）, Mg（II）, K （I）, La（III） and Y（III） was carried out in the mixed solvent system using cellulose fiber supported solid membrane.

Transport of yttrium metal ions through fibers supported liquid membrane solvent extraction

A novel idea of transport of yttrium(Ⅲ) metal ions through fibers supported liquid membrane in two stage processes namely source to membrane and membrane to receiving phase has been proposed.The fibers supported liquid membrane was impregnated with different concentrations carrier.The experimental variables explored were concentration of yttrium(Ⅲ) ions,pH of source phase,PC-88A concentration in membrane phase,acid concentration in receiving phase and stirring speed.The pre-concentration of yttrium(Ⅲ) ions ...

Study on a Novel Disphase Supplying Supported Liquid Membrane for Transport Behavior of Divalent Nickel Ions

A novel d!sphase supplying supported liquid membrane （DSSLM）, containing supplying feed phase andsupplying stripping phase tor transport behavior ot NI（Ⅱ）, have been studied. The supplying supported feed phase included feed solution and di（2-ethyhexyl） phosphoric acid （HDEHP） as the carrier in kerosene, and supplying stripping phase included HDEHP as the cartier in kerosene and HC1 as the stripping agent. The effects of volume ratio of membrane solution to feed solution （O/F）, pH, initial concentration of Ni（Ⅱ） and ionic strength in the feedsolution, volume ratio of membrane solution to stripping solution （O/S）, concentration of H2SO4 solution, HDEHP concentration in the supplying stripping phase on transport of Ni（/I）, the advantages of DSSLM compared to the traditional supported liquid membrane （SLM）, the system stability, the reuse of membrane solution and the reten- tion of membrane phase were studied. Experimental results indicated that the optimum transpgrt of Ni（Ⅱ） was oh-tained when H2SO4 concentration was 2.00 mol＇L-＇, HDEHP concentration was 0.120 mol·L-1, and O/S was 4· 1 in the supplying stripping phase, O/F was 1 ： 10 and pH was 5.20 in the supplying feed phase. The ionic strength in supplying feed phase had no obvious effect on transport of Ni（Ⅱ）. When initial Ni（Ⅱ） concentration was 2.00x 10-4 mol/L, the transport percentage of Ni（Ⅱ） was up to 93.1% in 250 min. The kinetic equation was deduced in terms of the law of mass diffusion and the interface chemistry.

Preparation and Gas Permeation of Supported γ-Al_2O_3 Membranes Used as Substrate Layer for Microporous Membranes

γ-Al2O3 membranes were successfidly deposited on the top of porous α-Al2O3 support by sol-gel process and characterized by means of XRD , SEM, N2 adsorption and gas permeation. The γ-Al2O3 membranes, free of pin-holes and cracks, adhere tightly to the supports and have a thlekness of about 7μm. When sintered at 400 ℃ , γ-Al2O3 membranes have a rutrrow pore size distribution, with a pore diameter of 3.6nm, and the transport of both H2 and CO2 in supported γ-Al2O3 membrane is governed by Knudsen mechanism, with H2 permeance of 3.3× 10^-6 molm^-2Pa^-1s^-1 and H2/ CO2 permselectivity close to the ideal Knudsen value at 50 ℃ . The γ-Al2O3 membranes are suitable for being used as the substrates of microparoas membranes .

VIBRATION OF ARBITRARILY SHAPED MEMBRANES WITH ELASTICAL SUPPORTS AT POINTS

This paper presents a new method for solving the vibration of arbitrarily shaped membranes with ela.stical supports at points. The reaction forces of elastical supports at points are regarded as unknown external forces acting on the membranes. The exact solution of the equation of motion is given which includes terms representing the unknown reaction forces. The frequency equation is derived by the use of the linear relationship of the displacements with the reaction forces of elastical supports at points. Finally the calculating formulae of the frequency equation of circular membranes are analytically performed as examples and the inherent frequencies of circular membranes with symmetric elastical supports at two points are numerically calculated.

Methyl Cholate and Resorcinarene New Carriers for the Recovery of Cr(Ⅲ) Ions by Supported Liquid Membranes (SLM)s

The technique of supported liquid membranes was used to achieve the facilitated transport of Cr(III) ions, using tow amphiphilic carriers, the methyl cholate and resorcinarene. For prepared SLMs, toluene as organic phase and film of polyvinylidene difluoride, as hydrophobic polymer support with 100 μm in thickness and 0.45 μm as the diameter of the pores. The macroscopic parameters (P and J0) on the transport of these ions were determined for different medium temperatures. For these different environments, the prepared SLMs were highly permeable and a clear evolution of these parameters was observed. The parameter J0 depended on the temperature according to the Arrhenius equation. The activation parameters, Ea, ΔH≠ and ΔS≠, for the transition state on the reaction of complex formation (ST) , were determined. To explain these results for this phenomenon, and achieve a better extraction of the substrate, a model based on the substrate complexation by the carrier and the diffusion of the formed complex (ST) was developed. The experimental results verify this model and determine the microscopic parameters (Kass and D*). These studies show that these parameters Kass and D* are specific to facilitated transport of Cr(III) ions by each of the carriers and they are changing significantly with temperature.

Enhancing CO_(2) transport with plasma-functionalized ionic liquid membranes

The ionic liquid(IL) 1-butyl-3-methylimidazolium tetrafluoroborate treated with radiofrequency plasma is proposed for functionalization and immobilization on polyethersulfone supports to form supported ionic liquid membranes for CO_(2) separation.The effects of treatment time and transmembrane pressure difference on CO_(2) permeance were evaluated.The best gas permeation performance was obtained with a treatment time of 10 min and the transmembrane pressure difference was 0.25 MPa.Characterization of the materials by Fourier transform infrared spectroscopy,x-ray photoelectron spectroscopy and nuclear magnetic resonance spectroscopy demonstrates that the IL is grafted with carboxyl groups and deprotonated through plasma treatment.A preliminary mechanism for the plasma treatment and facilitated transport of CO_(2)has been proposed on this basis.

CO_2/N_2 separation using supported ionic liquid membranes with green and cost-effective [Choline][Pro]/PEG200 mixtures

The high price and toxicity of ionic liquids(ILs) have limited the design and application of supported ionic liquid membranes(SILMs) for CO_2 separation in both academic and industrial fields. In this work, [Choline][Pro]/polyethylene glycol 200(PEG200) mixtures were selected to prepare novel SILMs because of their green and costeffective characterization, and the CO_2/N_2 separation with the prepared SILMs was investigated experimentally at temperatures from 308.15 to 343.15 K. The temperature effect on the permeability, solubility and diffusivity of CO_2 was modeled with the Arrhenius equation. A competitive performance of the prepared SILMs was observed with high CO_2 permeability ranged in 343.3–1798.6 barrer and high CO_2/N_2 selectivity from 7.9 to 34.8.It was also found that the CO_2 permeability increased 3 times by decreasing the viscosity of liquids from 370 to38 m Pa·s. In addition, the inherent mechanism behind the significant permeability enhancement was revealed based on the diffusion-reaction theory, i.e. with the addition of PEG200, the overall resistance was substantially decreased and the SILMs process was switched from diffusion-control to reaction-control.

Recent development of ionic liquid membranes

The interest in ionic liquids(IL) is motivated by its unique properties, such as negligible vapor pressure, thermal stability, wide electrochemical stability window, and tunability of properties. ILs have been highlighted as solvents for liquid-liquid extraction and liquid membrane separation. To further expand its application in separation field, the ionic liquid membranes(ILMs) and its separation technology have been proposed and developed rapidly. This paper is to give a comprehensive overview on the recent applications of ILMs for the separation of various compounds, including organic compounds, mixed gases, and metal ions. Firstly, ILMs was classified into supported ionic liquid membranes(SILMs) and quasi-solidified ionic liquid membranes(QSILMs) according to the immobilization method of ILs. Then, preparation methods of ILMs, membrane stability as well as applications of ILMs in the separation of various mixtures were reviewed. Followed this, transport mechanisms of gaseous mixtures and organic compounds were elucidated in order to better understand the separation process of ILMs. This tutorial review intends to not only offer an overview on the development of ILMs but also provide a guide for ILMs preparations and applications.

Morphological characterization of Al_2O_3 membrane fabricated by sol-gel dip-coating method

Alumina membranes without pinholes and cracks were prepared by the sol-gel process using anunordum aluminium sulphate as the starting material. The effects of different preparing conditions on morphology characteristics of the membrane were investigated by scanning electron microscopy and 3D rotational microscopy. The preparing conditions include the amounts of drying control chemical additives （DCCA）, sintering procedure and sol-gel concentration. The results showed that PVA is a good crack-preventing reagent and the morphology of supported membranes was affected by ninny factors, including Al2O3 concentration, PVA/Al2O3 ratio, heating rate, membrane thickness and intrinsic defects of the substrate surface.

Morphological Characterization of γ-Al_2O_3 Membranes Fabricated from Ammonium Aluminum Sulphate

Supported γ-Al2O3 membranes without defects were prepared by the sol-gel procedure. The sol-gel method involved peptization of a boehmite (AlOOH) sol prepared from ammonium aluminium sulphate. The morphology of the supported membranes was characterized by scanning electron microscopy (SEM) and 3D rotational microscopy. Furthermore, the effects of different preparing conditions on morphological characteristics of the membrane were also investigated. The results show that PVA is a good crack-preventing agent and the morphology of supported membranes is affected by many factors, such as Al2O3 and PVA contents of the sol, drying and sintering procedures and intrinsic defects on the substrate surface.