One-pot synthesis of network supported catalyst using supramolecular gel as template

A simple and general strategy is described for preparing network supported catalyst through a one-pot synthetic procedure using supramolecular gel as template.This procedure directly attaches ligand to support during fabricating the support.Using this strategy,supported CuBr/di-（2-picolyl） amine catalyst with U-shaped fibrillar network was prepared and used in atom transfer radical polymerization of methyl methacrylate.XPS and SEM characterization of the catalyst revealed homogeneous distribution of ligand,sufficient reactive sites,adequate mechanical strength and macroporosity.The polymerization results demonstrated high activity and reusability of such catalyst.This strategy might be extended to other supported catalysts used in column reactors.

STUDIES ON TiCI4/Mg (OEt)_2/EB SUPPORTED CATALYSTS FOR PROPYLENE POLYMERIZATION

The supported catalysts for propylene polymerization were prepared by milling Mg (OEt)_2 with EB (ethylbenzoate) and treating with TiCl_4 solution. When TiCl_4/(Mg(OEt)_2/EB) (mol.) ratio was increased, decrease in contents of-OEt and Ti of the catalysts was observed, while the content of EB increased. It is proved by analyses of IR, X-ray and XPS that during co-milling Mg(OEt)_2 with EB no reactions have taken place. But after treatment with TiCl_4 solution, Mg(OEt)_2 converts into MgCl_2 and EB coordinates on the resulting MgCl_2 carrier, a surface complex forms.The activity of catalysts,isotacticity and vicosimetric molecular weight of polypropylene increase with the decrease of the content of ethoxyl group. The kinetic curves of propene polymerization obtained with present catalysts system display decay curves. It is found from the triad tacticity calculated from the expanded spectra of methyl carbon region that, ethoxyl group in catalyst has an effect on the configuration of polymer chain.

Enhanced stability of nitrogen-doped carbon-supported palladium catalyst for oxidative carbonylation of phenol

Enhancing the stability of supported noble metal catalysts emerges is a major challenge in both science and industry.Herein,a heterogeneous Pd catalyst(Pd/NCF)was prepared by supporting Pd ultrafine metal nanoparticles(NPs)on nitrogen-doped carbon;synthesized by using F127 as a stabilizer,as well as chitosan as a carbon and nitrogen source.The Pd/NCF catalyst was efficient and recyclable for oxidative carbonylation of phenol to diphenyl carbonate,exhibiting higher stability than Pd/NC prepared without F127 addition.The hydrogen bond between chitosan(CTS)and F127 was enhanced by F127,which anchored the N in the free amino group,increasing the N content of the carbon material and ensuring that the support could provide sufficient N sites for the deposition of Pd NPs.This process helped to improve metal dispersion.The increased metal-support interaction,which limits the leaching and coarsening of Pd NPs,improves the stability of the Pd/NCF catalyst.Furthermore,density functional theory calculations indicated that pyridine N stabilized the Pd^(2+)species,significantly inhibiting the loss of Pd^(2+)in Pd/NCF during the reaction process.This work provides a promising avenue towards enhancing the stability of nitrogen-doped carbon-supported metal catalysts.

Porous silica nano-flowers stabilized Pt-Pd bimetallic nanoparticles as heterogeneous catalyst for efficiently synthesizing guaiacol from 2-methoxycyclohexanol

Porous silica nano-flowers(KCC-1)immobilized Pt-Pd alloy NPs(Pt-Pd/KCC-1)with different mass ratios of Pd and Pt were successfully prepared by a facile in situ one-step reduction,using hydrazinium hydroxide as a reducing agent.The as-synthesized silica nanospheres possess radial fibers with a distance of 15 nm,exhibiting a high specific surface area(443.56 m^(2)·g^(-1)).Meanwhile,the obtained Pt-Pd alloy NPs are uniformly dispersed on the silica surface with a metallic particle size of 4-6 nm,which exist as metallic Pd and Pt on the surface of monodisperse KCC-1,showing the transfer of electrons from Pd to Pt.The as-synthesized 2.5%Pt-2.5%Pd/KCC-1 exhibited excellent catalytic activity and stability for the continuous dehydrogenation of 2-methoxycyclohexanol to prepare guaiacol.Compared with Pt or Pd single metal supported catalysts,the obtained 2.5%Pt-2.5%Pd/KCC-1 shows 97.2%conversion rate of 2-methoxycyclohexanol and 76.8%selectivity for guaiacol,which attributed to the significant synergistic effect of bimetallic Pt-Pd alloy NPs.Furthermore,turn over frequency value of the obtained 2.5%Pt-2.5%Pd/KCC-1 NPs achieved 4.36 s^(-1),showing higher catalytic efficiency than other two monometallic catalysts.Reaction pathways of dehydro-aromatization of 2-methoxycyclohexanol over the obtained catalyst are proposed.Consequently,the obtained 2.5%Pt-2.5%Pd/KCC-1 NPs prove their potential in the dehydrogenation of 2-methoxycyclohexanol,while the kinetics and mechanistic study of the dehydrogenation reaction over the catalyst in a continuous fixed-bed reactor may provide valuable information for the development of green,outstanding and powerful synthetic pathway of guaiacol.

Boron-doped lamellar porous carbon supported copper catalyst for dimethyl oxalate hydrogenation

Doping heteroatoms on carbon materials could bring some special advantages for using as catalyst support.In this work, a boron doped lamellar porous carbon(B-LPC) was prepared facilely and utilized as carbonbased support to construct Cu/B-LPC catalyst for dimethyl oxalate(DMO) hydrogenation. Doping boron could make the B-LPC own more defects on surface and bigger pore size than B-free LPC, which were beneficial to disperse and anchor Cu nanoparticles. Moreover, the interaction between Cu species and B-LPC could be strengthened by the doped B, which not only stabilized the Cu nanoparticles, but also tuned the valence of Cu species to maintain more Cu^(+). Therefore, the B-doped Cu/B-LPC catalyst exhibited stronger hydrogenation ability and obtained higher alcohols selectivity than Cu/LPC, as well as high stability without decrease of DMO conversion and ethylene glycol selectivity even after 300 h of reaction at 240℃.

Endeavors on the development of efficient and sustainable supported metal catalysts for chemical synthesis on solid-liquid interfaces

Supported metal catalysts,particularly for precious metals,have gained increasing attention in green synthetic chemistry.They can make metal-catalyzed organic synthesis more sustainable and economical due to easy separation of product with less metal residue,as well as reusability of the high-cost catalysts.Although great effort has been spent,the precise catalytic mechanism of supported metal-catalyzed reactions has not been clearly elucidated and the development of efficient and stable recyclable catalysts remains challenging.This highlight reveals a“molecular fence”metal stabilization strategy and discloses the metal evolution in Pd-catalyzed C-C bond formation reactions using Nheterocyclic carbene(NHC)-functionalized hypercrosslinked polymer support,wherein the polymeric skeleton isolates or confines the metal species involved in the catalytic reactions,and NHC captures free low-valent metal species in solution and stabilizes them on the support via strong metal-support coordination interaction.This strategy creates a novel route for the development of supported metal catalysts with high stability and provides insights into the reaction mechanism of heterogeneous catalysis.

Effective depolymerization of alkali lignin using an attapulgite-Ce_(0.75)Zr_(0.25)O_(2)(ATP-CZO)-supported cobalt catalyst in ethanol/isopropanol media

Lignin is the world's greatest renewable aromatic biofeedstock,and it has promising applications in high value-added chemical products.Herein,N-Co/ATP-CZO was used as a catalyst for the depolymerization of alkali lignin in ethanol and isopropanol systems,and explored the effects of formic acid(FA)amount,reaction time,reaction temperature and other factors on the depolymerization of alkali lignin.Among them,formic acid serves as both catalytic and in situ-hydrogen donor.Ultimately,the highest yield of bio-oil(59.28%(mass)),including 30.05%(mass)of monomer,was obtained after a reaction of FA to alkali lignin mass ratio of 4 and 240°C for 8 h.Among the monomers,the yield of Guaiacol was the highest(5.94%(mass)),followed by 2-methoxy-4-methylphenol(5.74%(mass)).This study,the modification of attapulgite was carried out to reduce the acidity while enhancing the catalytic activity for depolymerization,and the selection of hydrogen donor was investigated.A feasible pathway for lignin depolymerization research was opened.

Partial oxidation of methane over SiO2 supported Ni and NiCe catalysts

Nickel and nickel-ceria catalysts supported on high surface area silica, with 6 wt% Ni and 20 wt% CeO2 were prepared by microwave assisted(co) precipitation method. The catalysts were investigated by XRD,TPR and XPS analyses and they were tested in partial oxidation of methane(CPO). The catalytic reaction was carried out at atmospheric pressure in a temperature range of 400–800℃ with a feed gas mixture containing methane and oxygen in a molecular ratio CH4/O2=2. The Ni catalyst exhibited 60% methane conversion with 60% selectivity to CO already at 500℃. On the contrary, the Ni–Ce catalyst was inert to CPO up to 700℃. Moreover, the former catalyst reproduced its activity at the descending temperatures maintaining a good stability at 600℃, over a reaction time of 80 h, whereas the latter one completely deactivated. Test of CH4 temperature programmed surface reaction(CH4-TPSR) revealed a higher methane activation temperature(> 100℃) for the Ni–Ce catalyst as compared to the Ni one. Noticeable improvement of the ceria containing catalyst occurred when the reaction test started at a temperature higher than the methane decomposition temperature. In this case, the sample achieved the same catalytic behavior of the Ni catalyst. As confirmed by XPS analyses, the distinct electronic state of the supported nickel was responsible for the differences in catalytic behavior.

PREPARATION OF NOVEL POLYETHYLENE-graft-POLY(4-VINYLPYRIDINE)-SUPPORTED METALLOCENE CATALYSTS FOR ETHYLENE POLYMERIZATION

Polyethylene (PE) grafting 4-vinylpyridine copolymers has been produced as powders of different rushes by theirradiation method. After treatment with methylaluminoxane (MAO), the copolymers were used as supports for Cp_2ZrCl_2catalyst Results of X-ray photoelectron spectroscopy, Fourier transforms infrared spectroscopy, ultraviolet spectroscopy andscanning electron microscope measurements show that the catalytic sites have been linked through MAO on the PE-graft-4-vinylpyridine (PEVP). The percentages of grafting 4-vinylpyridine and supported Cp_2ZrCl_2 depend on the size ofpolyethylene powder. The smaller the polyethylene powder, the more percent of 4-vinylpyridine groups and Cp_2ZrCl_2 existon the polyethylene chains, and the PEVP-supported catalyst has a relatively high activity for ethylene polymerization.

Preparation of Nano-Sized γ-Al_2O_3 Supported Iron Catalyst for Fischer-Tropsch Synthesis by Solvated Metal Atom Impregnation Methods

Two types of small iron clusters supported on γ-Al2O3-RT（dehydroxylated at room temperature） and γ-Al2O3-800 （dehydroxylated at 800 ℃） were prepared by solvated metal atom impregnation （SMAI） techniques. The iron atom precursor complex, bis（toluene）iron（0） formed in the metal atom reactor, was impregnated into γ-Al2O3 having different concentrations of surface hydroxyl groups to study the effect of surface hydroxylation on the crucial stage of iron cluster formation. Catalysts prepared in this way were characterized by TEM, Mǒssbauer, and chemisorption measurements, and the results show that higher concentration of surface hydroxyl groups of γ-Al2O3-RT favors the formation of more positively charged supported iron cluster Fen/γ-Al2O3-RT, and the lower concentration of surface hydroxyl groups of γ-Al2O3-800 favors the formation of basically neutral supported iron cluster Fen/γ-Al2O3-800. The measured results also indicate that the higher concentration of surface hydroxyl groups causes the rapid decomposition of precursor complex, bis（toluene）iron（0）, and favors the formation of relatively large iron cluster. Consequently, these two types of catalysts show different catalytic properties in Fischer-Tropsch reaction. The catalytic pattern of Fen/γ-Al2O3-RT in F-T reaction is similar to that of the unreduced γ-Fe2O3 and that of Fen/γ-Al2O3-800 is similar to that of the reduced α-Fe2O3.

Controlled Radical Polymerization of Methyl Methacrylate Catalyzed by Hybrid Supported Iron Catalyst

A supported iron catalyst, which was prepared by anchoring FeCl2/FeCl3 on the cross-linking macroporous polyacrylate ion exchange resin, was evaluated via the controlled radical polymerization. When a small amount of CuCl2/ Me6TREN was added, the controllability of the polymerization over the iron-mediated catalyst was significantly improved（Mw/Mn = 1.23-1.73 ）, affording a polymer with a low residual metal via a simple catalyst separation procedure. After suitable regeneration, the supported iron catalyst could also he recycled. UV-Vis analysis showed that the additional copper catalyst could facilitate the radical deactivation process.

Oxidative desulfurization of diesel fuel oil using supported Fenton catalysts and assisted with ultrasonic energy

An ultrasound-assisted heterogeneous catalytic oxidation process was applied to eliminate sulfur from commercial diesel fuel oil.The studied variables were catalyst concentration,type of catalyst(homogeneous or heterogeneous),oxidizing agent concentration,and the application of ultrasound energy.Supported catalysts were prepared by impregnation of coal fly ash with an iron(Ⅱ)sulfate aqueous solution using ultrasound energy.After drying,the catalyst was calcined at 500℃for 4 h.The oxidizing agent was hydrogen peroxide.Ultrasound energy was applied with a frequency of 47 kHz and an intensity of 147 W.Ethanol was employed for extracting the oxidized compounds from the hydrocarbon mixture.Coal fly ash and ethanol were used with the purpose of applying low-cost raw materials in chemical processes.It was found that under the studied conditions,increasing oxidizing agent concentration and the application of ultrasound energy can enhance the sulfur removal from commercial diesel fuel oil.Catalyst concentration did not play a significant role in the process.Similar results were obtained using homogeneous or heterogeneous catalyst,which is important since the heterogeneous catalyst could be recovered,reactivated,and used in many cycles.

Supported catalysts for simultaneous removal of SO_(2),NO_(x),and Hg^(0)from industrial exhaust gases:A review

The simultaneous removal of SO_(2),NO_(x)and Hg^(0)from industrial exhaust flue gas has drawn worldwide attention in recent years.A particularly attractive technique is selective catalytic reduction,which effectively removes SO_(2),NO_(x)and Hg^(0)at low temperatures.This paper first reviews the simultaneous removal of SO_(2),NO_(x)and Hg^(0)by unsupported and supported catalysts.It then describes and compares the research progress of various carriers,eg.,carbon-based materials,metal oxides,silica,molecular sieves,metal-organic frameworks,and pillared interlayered clays,in the simultaneous removal of SO_(2),NO_(x)and Hg^(0).The effects of flue-gas components(such as O_(2),NH3,HCl,H2 O,SO_(2),NO and Hg^(0))on the removal of SO_(2),NOx,and Hg^(0)are discussed comprehensively and systematically.After summarizing the pollutantremoval mechanism,the review discusses future developments in the simultaneous removal of SO_(2),NOx and Hg^(0)by catalysts.

SILICA-SUPPORTED NICKEL AND ZIRCONIUM CATALYSTS FOR BRANCHED POLYETHYLENE

8-Aminoquinoline nickel dichloride and bis(cyclopentadienyl)zirconium dichloride (Cp_2ZrCl_2) were supportedsimultaneously on silica to produce branched polyethylene successfully by combined polymerization. The supportedpolymerization results showed that the molecular weight of polyethylene increased while the molecular weight distributionbecame wider and the molecular chains of oligomers remaning in the final solution became shorter as compared to theoligomers obtained in polymerization processes with pure 8-aminoquinoline nickel dichloride catalysis, as well as theCp_2ZrCl_2 and nickel combination system. With decreasing amount of Ni catalyst in the supported catalyst, the molecular chains of oligomers in the resulting solution became shorter, while α-olefin selectivity increased.

Effect of Reduction Temperature on Hydrofining Performance of Supported Molybdenum Phosphide Catalyst

A series of supported molybdenum phosphide catalysts were prepared by impregnation method. XRD, TG-DTG, XPS and BET were used to study the phase, compositions and surface areas of the prepared catalysts. A model reactant containing thiophene, pyridine and cyclohexene was used for the measurements of catalytic activities. The effect of reduction temperature on catalytic activities was investigated. The analysis results by XRD and BET are very different when the reduction temperature is changed from 400 to 900 ℃. MoP/γ-Al2O3 catalysts and CoMoP/γ-Al2O3 catalysts prepared at the reduction temperature of 500 ℃ are the most active ones.

Characteristics of Titanocene Catalyst Supported on Palygorskite for Ethylene Polymerization

A series of heterogeneous catalysts with Cp2TiCl2 supported on palygorskite were prepared and evaluated by ethylene slurry polymerizations. The so-called direct supported catalyst, for which the pretreatment of palygorskite with MAO or Al（i-Bu）3 was not necessary, gave the highest activity among these supported catalysts and could be more robust than homogeneous Cp2TiCl2. With the direct supported catalyst, no significant activity loss was observed under low Al/Ti molar ratios （Al/Ti=300） and the decay of polymerization rate was slower when compared to the other supported catalysts. It was found that the surface Lewis acidity of palygorskite after thermal treatment played an important role in activation of metallocene compound and resulted in high catalyst activity.

Vapor-phase Nitration of Benzene to Nitrobenzene over Supported Sulfuric Acid Catalyst

Vapor-phase nitration of benzene over solid acid catalyst is expected to be a clean process with no sulfuric acid waste. We investigated this process over solid acidic catalysts utilizing diluted nitric acid (60-70%) as nitrating agent, and found that supported sulfuric acid catalyst exhibited a very high catalytic activity. Under the conditions of reaction temperature 160-170℃, space velocity (SV) 1200 h-1, the yield and the space-time yield (STY) of nitrobenzene (NB) based on HNO3 were more than 98% and 0.75 kg穔gcat-1穐-1 over 10% H2SO4/SiO2 (by weight) catalyst respectively.

A Novel Carbon Nanotube-Supported NiP Amorphous Alloy Catalyst and Its Hydrogenation Activity

A carbon nanotube-supported NiP amorphous catalyst （NiP/CNT） was prepared by induced reduction. Benzene hydrogenation was used as a probe reaction for the study of catalytic activity. The effects of the support on the activity and thermal stability of the supported catalyst were discussed based on various characterizations, including XRD, TEM, ICP, XPS, H2-TPD, and DTA. In comparison with the NiP amorphous alloy, the benzene conversion on NiP/CNT catalyst was lower, but the specific activity of NiP/CNT was higher, which is attributed to the dispersion produced by the support, an electron-donating effect, and the hydrogen-storage ability of CNT. The NiP/CNT thermal stability was improved because of the dispersion and electronic effects and the good heat-conduction ability of the CNT support.

Simultaneous catalytic removal of NOx and diesel soot particulate over perovskite-type oxides and supported Ag catalysts

A series of perovskite type oxides and supported Ag catalysts were prepared, and characterized by X ray diffraction (XRD) and X ray photoelectron spectroscopy (XPS). The catalytic activities of the catalysts as well as influencing factors on catalytic activity have been investigated for the simultaneous removal of NOx and diesel soot particulate. An increase in catalytic activity for the selective reduction of NOx was observed with Ag addition in these perovskite oxides, especially with 5% Ag loading. This catalyst could be a promising candidate of catalytic material for the simultaneous elimination of NOx and diesel soot.

Study on the Reaction Mechanism for Carbon Dioxide Reforming of Methane over supported Nickel Catalyst

The adsorption and dissociation of methane and carbon dioxide for reforming on nickel catalyst were extensively investigated by TPSR and TPD experiments. It showed that the decomposition of methane results in the formation of at least three kinds of surface carbon species on supported nickel catalyst, while CO2 adsorbed on the catalyst weakly and only existed in one kind of adsorption state. Then the mechanism of interaction between the species dissociated from CH4 and CO2 during reforming was proposed.