Cooperative effect of surface alloying and laser texturing on tribological performance of lubricated surfaces

The cooperative effect of laser surface texturing(LST) and double glow plasma surface alloying on tribological performance of lubricated sliding contacts was investigated.A Nd:YAG laser was used to generate microdimples on steel surfaces. Dimples with the diameter of 150μm and the depth of 30-35μm distributed circumferentially on the disc surface.The alloying element Cr was sputtered to the laser texturing steel surface by double glow plasma technique.A deep diffusion layer with a thickness of 30μm and a high hardness of HV900 was formed in this alloy.Tribological experiments of three types of samples(smooth,texturing and texturing+alloying) were conducted with a ring-on-disc tribometer to simulate the face seal.It is found that,in comparison with smooth steel surfaces,the laser texturing samples significantly reduce the friction coefficient.Moreover,the lower wear rate of the sample treated with the two surface techniques is observed.

Tribological Properties of Dimpled Surface Alloying Layer on Carbon Steel

The effect of surface structure and coating on tribological properties of 45^# carbon steel disc was analyzed. A Nd：YAG laser was used to generate rnicrodirnples on steel surfaces. Dimples with diameter of 150 rn and depth of 50 rn were distributed in an orbicular array on disc surface. Then the alloying element Mo was sputtered to 45# carbon steel disc surface by means of double glow plasma technology. Diffusion Mo alloying layer with 30min thickness and high hardness up to 0.025 was formed on the disc surface. Tribological experiments of three types samples （smooth, texturing and texturing＋alloying） were conducted with a pin-on-disc tribometer. It is found that the dimpled-samples are most effective for reducing friction in comparison with smooth steel surthces, improving the lubricating state from boundary to hydrodynamic region.

Study on microstructure and properties of Mg-alloy surface alloying layer fabricated by EPC

AZ91D surface alloying was investigated through evaporative pattern casting （EPC） technology. Aluminum powder （0.074 to 0.104 mm） was used as the alloying element in the experiment. An alloying coating with excellent properties was fabricated, which mainly consisted of adhesive, co-solvent, suspending agent and other ingredients according to desired proportion. Mg-alloy melt was poured under certain temperature and the degree of negative pressure. The microstructure of the surface layer was examined by means of scanning electron microscopy. It has been found that a large volume fraction of network new phases were formed on the Mg-alloy surface, the thickness of the alloying surface layer increased with the alloying coating increasing from 0.3 mm to 0.5 mm, and the microstructure became compact. Energy dispersive X-ray （EDX） analysis was used to determine the chemical composition of the new phases. It showed that the new phases mainly consist of/3-MglTAI12, in addition to a small quantity of inter-metallic compounds and oxides. A micro-hardness test and a corrosion experiment to simulate the effect of sea water were performed. The result indicated that the highest micro-hardness of the surface reaches three times that of the matrix. The corrosion rate of alloying samples declines to about a fifth of that of the as-cast AZ91D specimen.

Plasma Niobium Surface Alloying of Pure Titanium and its Oxidation at 900 ℃

A niobium-modified layer on pure titanium surface was obtained by means of double glow plasma surface alloying technique. The modified layer was uniform, continuous, compact and well adhered to the substrate. The niobium composition in the modified layer decreased gradually from the surface to the substrate. The oxidation behavior of the niobium-modified layer was investigated and com- pared with the untreated surface at 900 ~C for 100 h. Characterization of the layers was performed using X-ray diffraction and scanning electron microscope, respectively. The test results show that the oxidation behavior of pure titanium was improved by niobium alloying process. Niobium has a positive influence on the oxidation resistance.

Oxidation behavior of niobized TiAl by plasma surface alloying

Plasma surface alloying of element Nb in TiAl-based alloys and the oxidation behavior were studied. The composition and microstructure of the surface alloyed layers were investigated by means of scanning electron microscopy （SEM）,energy dispersive X-ray analysis （EDX）,and X-ray diffraction （XRD）. The experimental results indicate that the diffusion layers are formed on the TiAl substrate during the plasma niobizing process. The result from oxidation resistance investigation shows that plasma niobizing greatly improves the oxidation resistance of TiAl compared with the untreated TiAl. The role of element Nb for improving the oxidation resistance is considered to be achieved by strengthening the activity of Al,which is induced by the plasma niobizing process.

EVOLUTION OF MICROSTRUCTURE OF LASER SURFACE ALLOYING OF γ TiAi ALLOY WITH NITROGEN

Laser surface alloying of γ TiAl alloy with nitrogen was studied under the constant protective nitrogen current (20l /min). The experimental results shown that the surface multi layers formed with experimental parameters could be up to 600μm depth; it consists of TiN,Ti 2AlN,α 2 and γ phases, without AlN, and the irregular coarse continuous “flow” line,dendrite,needle and granular nitrides disperse on the fine dendrite casting α 2 and γ phases substrate. The microstructure and compositions in the nitiding layer were determined and analyzed by SEM and EPMA and the mechanism for the formation of microstructure in the nitriding layer was also discussed.

Effects of C,N-Codoped on the Corrosion Resistance of TiO_2 Films Prepared by Plasma Surface Alloying and Thermal Oxidation Duplex Process

C,N-codoped TiO 2 films have been deposited onto stainless steel substrates using plasma surface alloying and thermal oxidation duplex process.Composition analysis shows that the films shield the substrates entirely.The TiO 2 films are anatase in structure as characterized by X-ray diffraction.The electrochemical measurements show that the equilibrium corrosion potential positively shifts from-0.275 eV for bare stainless steel to-0.267 eV for C,N-codoped TiO 2 coated stainless steel,and the corrosion current density decreases from 1.3×10-5 A/cm2 to 4.1×10-6 A/cm2.The corrosion resistance obtained by electrochemistry noise also reveals that the C,N-codoped TiO 2 films provide good protection for stainless steel against corrosion in stimulated body fluid.The above results indicate that C,N-codoped TiO 2 films deposited by plasma surface alloying and thermal oxidation duplex process are effective in protecting stainless steel from corrosion.

Thermodynamic analysis of carbon migration in W1-1.0C steel in plasma surface chromizing

W 1-1.0C steel was chromized at 1173 K with double glow plasma surface alloying process, and the distribution of Fe, Cr, and C contents in the chromized layer was measured using glow discharge spectrum analysis （GDA）. The behavior and mechanism of carbon migration during the formation of chromized layer were studied through thermodynamic analysis and calculation. The gradient of carbon chemical potential was regarded as the driving force of carbon migration. An equation was derived to describe the carbon content varying with the chromium content within the carbon-rich region. The calculated results from the equation approximated closely to the experimental ones.

Microstructure and Properties of Laser Surface Alloying 304 Stainless Steel with Si

Silicon was added to the surface of 304 stain- less steel by laser melting the sprayed preplaced Si powders.The optical microscopy,X-ray diffraction and EPMA were employed to investigate the microstructure and chemical composition of the laser surface alloyed layer.The hardness of the al- loyed layer was measured by microhardness test and wear resistance was evaluated by scratch test. Corrosion resistance of laser alloyed sample was studied in 1N H_2SO_4+0.1N NaCl and 0.5N HCl+0.5N NaCl aqueous solutions.A microcrystalline intermetallic compound coating with smooth surface and good chemical homogeneity without porosity and crack is ob- tained.The hardness is about 720 HV.The wear re- sistance is 2 times better than that of the substrate. The corrosion resistance of the laser alloyed sample is much better than that of 304 stainless steel sample.

Microstructure and high-temperature wear properties of in situ TiC composite coatings by plasma transferred arc surface alloying on gray cast iron

In this work, an in situ synthesized TiC-reinforced metal matrix composite （MMC） coating of approximately 350-400μm thickness was fabricated on a gray cast iron （GCI） substrate by plasma transferred arc （PTA） surface alloying of Ti-Fe alloy powder. Microhard- ness tests showed that the surface hardness increased approximately four-fold after the alloying treatment. The microstructure of the MMC coating was mainly composed of residual austenite, acicular martensite, and eutectic ledeburite. Scanning electron microscopy （SEM） and X-ray diffraction analyzes revealed that the in situ TiC particles, which were formed by direct reaction of Ti with carbon originally contained in the GCI, was uniformly distributed at the boundary of residual anstenite in the alloying zone. Pin-on-disc high-temperature wear tests were performed on samples both with and without the MMC coating at room temperature and at elevated temperatures （473 K and 623 K）, and the wear behavior and mechanism were investigated. The results showed that, after the PTA alloying treatment, the wear resistance of the sam- ples improved significantly. On the basis of our analysis of the composite coatings by optical microscopy, SEM with energy-dispersive X-ray spectroscopy, and microhardness measurements, we attributed this improvement of wear resistance to the transformation of the microstruc- ture and to the presence of TiC particles.

HIGH-CURRENT PULSED ELECTRON BEAM: RAPID SURFACE ALLOYING AND WEAR RESISTANCE IMPROVEMENT

The present paper reports the rapid surface alloying induced by the bombardment of high-current pulsed electron beam. Two kinds of substrate materials were examined to show this effect. The first sample was a pure Al metal pre-coated with fine carbon powders prior to the bombardment, and the second alloy is the D2-Crl2MolVl mould steel pre-coated with Cr, Ti, and TiN powders. The surface elements diffuse about several micrometers into the substrate materials only after several bombardments. Tribological behaviors of these samples were characterized and significant improvement in wear resistance was found. Finally, a TEM analysis reveals the presence of stress waves generated by coupled thermal and stress fields, which was considered as the main cause of the enhanced properties.

Effect of Counterface Materials on Friction and Wear Behavior of Double Glow Glasma Discharge Surface Alloying on Ti22Al25Nb Alloy

Samples of surface chromising layer were prepared by the double glow plasma discharge technique. X-ray diffraction and X-ray photoelectron spectroscopy（XPS） analysis of dif-ferent elements confirmed the formation of chrome in the layer. Their tribological properties were investigated by pin-on-disk tribometer. Silicon nitride, GCr15, and nickel-based alloy were selected as counterface materials. Results indicated that the lowest friction coefficients and wear rate were ob-tained when substrate and chromising layer against nickel-based alloy, and tribological properties of chromising layer were better than those of substrate. The highest friction and wear rate were samples against silicon nitride alloys. In the case of three rubbing pairs, the unchangeable materials against different hardness counterfaces leaded to different wear mechanisms. Samples against silicon nitride exhibited abrasive mechanism, and when GCr15 and nickel-based alloy were used as counterface, transfer film and glaze layer formed on the contact surface, which played the main role in decreasing friction and wear.

The Diagnosis of Plasma Parameters in Surface Alloying Technique by Optical Emission Spectrometry

Electron density （Ne） in a glow discharge plasma for the surface alloying technique is diagnosed by optical emission spectrometry （OES）. With CH4 as the feeding gas, Ne is obtained by comparing the Hβ spectrum according to the Stark broadening effect. It is noticed that Ne varies with the working pressures （30 Pa to 70 Pa） and cathode voltages （500 V to 1000 V）, respectively. Due to an abnormal glow discharge, Ne is between 1. 71 × 10^15 /cm^3 to 6.64 × 10^15 /cm^3 and increases rapidly with working gas pressures and cathode voltages. The results show that OES is a useful method to measure the plasma parameters in a surface alloying glow discharge plasma.

Mg alloy surface alloying layer fabricated through evaporative pattern casting technology

The influencing factors of surface alloying layer by evaporative pattern casting technology were investigated.A certain thickness alloying layer was formed on the surface of Mg-alloy matrix when the pouring temperature was 780°C with different vacuum degree and alloying powder size.The surface layer microstructure,micro area composition of the new phase formed on the matrix and the composition characteristics on the surface layer were examined by SEM and element scanning.The results show that the content of aluminum increases greatly on the surface layer.The micro-hardness of alloyed layer has a more obvious increase compared with that of the matrix.The size of alloying element and the vacuum degree are the key factors influencing the alloying layer,with the increase of element powder size from 0.074 to 0.15 mm and vacuum degree from 0.04 to 0.06 MPa,the surface alloying effect becomes better.

Optimizing Domain Distribution of Grain Oriented Silicon Steel by Using Antimony as the Laser Surface Alloying Element

For reducing the core loss of grain oriented silicon steel and improving its aging property, a new method, the LLSA by using Sb as the laser surface alloying element, was investigated, and at proper technique conditions rather good result was obtained.

DOUBLE GLOW PLASMA SURFACE ALLOYING OF Ti6A14V AND TiAl

In order to improve the wear resistance of titanium alloy Ti6Al4V and high temperature oxidation resistance of intermetallic compound TiAl, the Double Glow Plasma Surface Alloying Technique (DG technique) was applied to modify the surface properties of these materials. Mo, Nb, Cr, Ni were diffused into the substrate materials to form alloyed layers with different properties. This paper shows the microstructure, microhardnesses, distributions of the alloy elements on the alloyed layers. Wear and high temperature oxidation tests were carried out. Test results indicate that the wear resistance of Ti6Al4V and the high temperature oxidation resistance of TiAl were improved significantly.

Microstructure and corrosion resistance of Fe-Al intermetallic coating on 45 steel synthesized by double glow plasma surface alloying technology

A binary Fe-Al alloyed layer was synthesized on 45 steel by means of double glow plasma surface alloying technique. The corrosion-resisting layer prepared is composed of a sedimentary layer and a diffusion layer, with a total thickness of about 180 μm. The aluminum content of the alloyed layer shows gradual change from surface to the inside of substrate. The ideal profile is beneficial to the metallurgical bonding of the surface alloying layer with substrate materials. The microstructure of both layers consists of the Fe-Al intermetallic compound, which is FeAl with B2 structure in the sedimentary layer and Fe3Al with incompletely ordered DO3 structure in the diffusion layer. The protective film exhibits high micro-hardness. In comparison with the substrate of 45 steel, the corrosion resistance of the aluminized sample is much higher in 2.0% Na2S and 0.05 mol/L Na2SO4 + 0.5 mol/L NaCl mixed solutions.

A Hybrid Low Temperature Surface Alloying Process for Austenitic Stainless Steels

This paper describes a novel, hybrid process developed to engineer the surfaces of austenitic stainless steels at temperatures below 450°C for the improvement in wear and corrosion resistance. The process is carried out in the plasma of a glow discharge containing both nitrogen and carbon reactive species, and facilitates the incorporation of both nitrogen and carbon into the austenite surface to form a dual-layer structure comprising a nitrogen-rich layer on top of a carbon-rich layer. Both layers can be precipitation-free at sufficiently low processing temperatures, and contain nitrogen and carbon respectively in supersaturated fee austenite solid solutions. The resultant hybrid structure offers several advantages over the conventional low temperature nitriding and the newly developed carburizing processes in terms of mechanical and chemical properties, including higher surface hardness, a hardness gradient from the surface towards the layer-core interface, uniform layer thickness, and much enhanced corrosion resistance. This paper discusses the main features of this hybrid process and the various structural and properties characteristics of the resultant engineered surfaces.

Plasma surface alloying of titanium alloy for enhancing burn-resistant property

Conventional titanium alloy may be ignited and burnt under high temperature, high pressure and high gas flow velocity condition. In order to avoid this problem,burn-resistant alloying layers were made on the surface of Ti-6Al-4V and Ti-6.5Al-0.3Mo-1.5Zr-0.25Si titanium alloys by using double glow plasma surface alloying technology (DG Technology). Two typical burn-resistant layers Ti-Cr and Ti-Mo were made by DG plasma chromizing and DG plasma molybdenizing, respectively. Burn-resistant properties were tested by layer ignition method using 2 kW laser machine. Ignition experiments result reveals that the ignition temperature of alloyed layer with Mo and Cr concentration above 10% is about 200℃higher than ignition temperature of Ti-6Al-4V substrate.

Laser surface alloying fabricated porous coating on NiTi shape memory alloy

Laser surface alloying technique was applied to fabricate a metallic porous coating on a solid NiTi shape memory alloy. By laser surface alloying a 40%TiH2-60%NiTi powder mixture on the surface of NiTi alloy using optimized laser process parameters, a porous but crack-free NiTi layer can be fabricated on the NiTi substrate. The porous coating is metallurgically bonded to the substrate NiTi alloy. The pores are uniformly distributed and are interconnected with each other in the coating. An average pore size of less than 10 μm is achieved. The Ni content of the porous layer is much less than that of the original NiTi surface. The existence of the porous coating on the NiTi alloy causes a 37% reduction of the tensile strength and 55% reduction of the strain as compared with the NiTi alloy. Possible biomedical or other applications for this porous surface with good mechanical strength provided by the substrate are prospective.