Geochemistry and Modes of Occurrence of Hazardous Trace Elements in the No.11 Coal Seam,Antaibao Surface Mine,Shanxi Province

Concentrations of seventeen hazardous trace elements including As, Pb, Hg, Se, Cd, Cr, Co, Mo, Mn, Ni, U, V, Th, Be, Sb, Br and Zn in the No.ll coal seam, Antaibao surface mine, Shanxi Province were determined using Instrumental Neutron Activation Analysis （INAA）, Inductively Coupled Plasma Atomic Emission Spectrometry （ICP-AES）, Cold-Vapor Atomic Absorption Spectrometry （CV-AAS） and Graphite Furnace Atomic Absorption Spectrometry （GF-AAS）. Comparisons with average concentrations of trace elements in Chinese coal show that the concentrations of Hg and Cd in the No. 11 coal seam, Antaibao surface mine are much higher. They may be harmful to the environment in the process of utilization. The variations of the trace elements contents and pyritic suffur in vertical section indicated that： （a） the concentrations of As, Pb, Mn, and pyritic sulfur decrease from roof to floor; （b） the concentrations of Cr, Zn and Mo are higher in roof, floor and lower in coal seam; （c） the concentration of Br, Sb, and Hg are higher in coal seam and lower in roof and floor; （d） the concentrations of Mo, V, Th and AI vary consistently with the ash yield. Cluster analysis of trace elements, pyritic sulfur, ash yield and major elements, such as AI, Fe, P, Ca shows that： （a） pyritic sulfur, Fe, As, Mn, Ni, Be are closely associated and reflect the influence of pyrite; （b） Mo, Se, Pb, Cr, Th, Co, Ca and A! are related to clay mineral, which is the main source of ash; （c） U, Zn, V, Na, P maybe controlled by phosphate or halite; （d） Hg, Br, Sb and Cd may be mainly organic-associated elements which fall outside the three main groups. The concentration distribution characteristics of trace elements in coal seam and the cluster analysis of major and trace elements showed that the contents of trace elements in the No. 11 coal seam, Antaibao surface mine, are mainly controlled by detrital input and migration from roof and floor.

A flexible multi-body model of a surface miner for analyzing the interaction between rock-cutting forces and chassis vibrations

The discontinuous nature of rock cutting can easily cause unwanted vibrations in the structure of a surface miner.If these vibrations are not properly addressed,the related stress cycles can gradually damage the chassis resulting in fatigue failures.These events can seriously undermine the safety of operators and digging operations may be stopped for days,with an obvious economic impact.This work presents an analysis of the dynamics of a surface miner,focusing on the interaction between cutting machine dynamics and cutting forces,which is a new approach for this type of machine.For this purpose,the authors developed a numerical model of the cutting process made up of(1)a multi-body model of the cutting machine,which takes into account the chassis's flexibility;(2)a model of the rotating cutting head;and(3)a model of the interaction between the cutting head and rock,based on Shao's model.The model was compared with experimental results and then used to investigate the effects of cutting speed and cutting depth on the machine dynamics.

Feasibility study of highwall mining in north surface mine of Yima Coal Corporation, China

Yima Coal Corporation is considering to adopt highwall mining method withauger machine to recover coal from north surface pit that has reached final highwall position. Themajor geomechanical issues associated with auger mining are highwall and pillar stability. Based onthe field investigation and laboratory test results of mechanical parameters, numerical modeling iscarried out to assess the stability of highwall and pillar. Field measurements of highwalldeformation have been used to validate and ensure the confidence for the development of realisticmodels. The results of numerical modeling show that the mining method is feasible for mining theseam of 10 m thickness in north surface coal mine.

Comparative study of mining methods for reserves beneath end slope in flat surface mines with ultra-thick coal seams

The paper aims to identify a reasonable method for mining ultra-thick coal seams in an end-slope in surface mine, With a case study of Heidaigou surface coal mine(HSCM), the paper conducted a comparative research on three mining methods, namely Underground Mining Method(UMM), Highwall Mining System(HMS) and Local Steep Slope Mining Method(LSSMM). A model was firstly established to simulate the impact that UMM and HMS exert on monitoring points and surface deformation. The way that stripping and excavation amount varies with different slope angle, and the corresponding end slope stability were analyzed in the mode of LSSMM. Then a TOPSIS model was established by taking into account six indicators such as recovery ratio, technical complexity and adaptability, the impact on surface mining production, production safety and economic benefits. Finally, LSSMM was determined as the best mining method for mining ultra-thick coal seams in end slope in HSCM.

A NEW TECHNIQUE FOR ROADWAY DUST CONTROL IN SURFACE MINE

ＡＮＥＷＴＥＣＨＮＩＱＵＥＦＯＲＲＯＡＤＷＡＹＤＵＳＴＣＯＮＴＲＯＬＩＮＳＵＲＦＡＣＥＭＩＮＥＡＮＥＷＴＥＣＨＮＩＱＵＥＦＯＲＲＯＡＤＷＡＹＤＵＳＴＣＯＮＴＲＯＬＩＮＳＵＲＦＡＣＥＭＩＮＥ￥ＭｅｎｇＴｉｎｇｒａｎｇ；ＷｕＣｈａｏ（Ｄｅｐａｒｔｍｅｎｔ...

Reliability Theory Study of Combined Mining Technology System in Surface Mines

The connection between all the single systems iu combined technology is analysed, and the mine engineering reliability is calculated in any area of the mines using combined technololgy system. The reliability design and distribution method in this system is put forward, thus the basis is set for the decision to raise the total production capability or the surface mines in which the combined system is used.

Experimental and numerical simulation study on forced ventilation and dust removal of coal mine heading surface

In order to study the problems of unreasonable airflow distribution and serious dust pollution in a heading surface,an experimental platform for forced ventilation and dust removal was built based on the similar principles.Through the similar experiment and numerical simulation,the distribution of airflow field in the roadway and the spatial and temporal evolution of dust pollution under the conditions of forced ventilation were determined.The airflow field in the roadway can be divided into three zones:jet zone,vortex zone and reflux zone.The dust concentration gradually decreases from the head to the rear of the roadway.Under the forced ventilation conditions,there is a unilateral accumulation of dust,with higher dust concentrations away from the ducts.The position of the equipment has an interception effect on the dust.The maximum error between the test value and the simulation result is 12.9%,which verifies the accuracy of the experimental results.The research results can provide theoretical guidance for the application of dust removal technology in coal mine.

Marine antifouling behavior of the surfaces modified by dopamine and antibacterial peptide

Marine biofouling causes serious harms to surfaces of marine devices in transportation,aquaculture,and offshore construction.Traditional antifouling methods pollute the environment.A novel and green antifouling strategy was developed to prevent effectively the adhe sion of bacteria and microalgae.An antifouling surface was fabricated via coating Turgencin BMox2(TB)onto dopamine-modified 304stainless steel(304 SS).The surface physical and chemical properties before and after modification were characterized by Fourier transform infrared spectrometer(FTIR),X-ray photoelectron spectrometer(XPS),contact angle measurement(CA),3D optical profilometer,ellipsometer,and atomic force microscope(AFM).Antimicrobial peptide was coated onto the surface of 304 SS successfully,and the surface morphology and wettability of the modified sample were modified.Moreover,cytocompatibility of the peptide was evaluated by co-culture of peptide and cells,indicating promising cell biocompatibility at the modified sample surface.At last,antifouling performance and electrochemical corrosion were tested.Results show that the adhesion rates of Vibrio natriegens and Phaeodactylum tricornutum on the antifouling surface were reduced by 99.85% and 67.93%,respectively from those of untreated samples.Therefore,the modified samples retained superior corrosion resistance.The study provide a simply and green way against biofouling on ship hulls and marine equipment.

El Niño and the AMO Sparked the Astonishingly Large Margin of Warming in the Global Mean Surface Temperature in 2023

In 2023,the majority of the Earth witnessed its warmest boreal summer and autumn since 1850.Whether 2023 will indeed turn out to be the warmest year on record and what caused the astonishingly large margin of warming has become one of the hottest topics in the scientific community and is closely connected to the future development of human society.We analyzed the monthly varying global mean surface temperature(GMST)in 2023 and found that the globe,the land,and the oceans in 2023 all exhibit extraordinary warming,which is distinct from any previous year in recorded history.Based on the GMST statistical ensemble prediction model developed at the Institute of Atmospheric Physics,the GMST in 2023 is predicted to be 1.41℃±0.07℃,which will certainly surpass that in 2016 as the warmest year since 1850,and is approaching the 1.5℃ global warming threshold.Compared to 2022,the GMST in 2023 will increase by 0.24℃,with 88%of the increment contributed by the annual variability as mostly affected by El Niño.Moreover,the multidecadal variability related to the Atlantic Multidecadal Oscillation(AMO)in 2023 also provided an important warming background for sparking the GMST rise.As a result,the GMST in 2023 is projected to be 1.15℃±0.07℃,with only a 0.02℃ increment,if the effects of natural variability—including El Niño and the AMO—are eliminated and only the global warming trend is considered.

A facile strategy for tuning the density of surface-grafted biomolecules for melt extrusion-based additive manufacturing applications

Melt extrusion-based additive manufacturing(ME-AM)is a promising technique to fabricate porous scaffolds for tissue engi-neering applications.However,most synthetic semicrystalline polymers do not possess the intrinsic biological activity required to control cell fate.Grafting of biomolecules on polymeric surfaces of AM scaffolds enhances the bioactivity of a construct;however,there are limited strategies available to control the surface density.Here,we report a strategy to tune the surface density of bioactive groups by blending a low molecular weight poly(ε-caprolactone)5k(PCL5k)containing orthogonally reactive azide groups with an unfunctionalized high molecular weight PCL75k at different ratios.Stable porous three-dimensional(3D)scaf-folds were then fabricated using a high weight percentage(75 wt.%)of the low molecular weight PCL 5k.As a proof-of-concept test,we prepared films of three different mass ratios of low and high molecular weight polymers with a thermopress and reacted with an alkynated fluorescent model compound on the surface,yielding a density of 201-561 pmol/cm^(2).Subsequently,a bone morphogenetic protein 2(BMP-2)-derived peptide was grafted onto the films comprising different blend compositions,and the effect of peptide surface density on the osteogenic differentiation of human mesenchymal stromal cells(hMSCs)was assessed.After two weeks of culturing in a basic medium,cells expressed higher levels of BMP receptor II(BMPRII)on films with the conjugated peptide.In addition,we found that alkaline phosphatase activity was only significantly enhanced on films contain-ing the highest peptide density(i.e.,561 pmol/cm^(2)),indicating the importance of the surface density.Taken together,these results emphasize that the density of surface peptides on cell differentiation must be considered at the cell-material interface.Moreover,we have presented a viable strategy for ME-AM community that desires to tune the bulk and surface functionality via blending of(modified)polymers.Furthermore,the use of alkyne-azide“click”chemistry enables spatial control over bioconjugation of many tissue-specific moieties,making this approach a versatile strategy for tissue engineering applications.

Analysis of the interaction between bolt-reinforced rock and surface support in tunnels based on convergence-confinement method

To investigate the interaction of the bolt-reinforced rock and the surface support,an analytical model of the convergence-confinement type is proposed,considering the sequential installation of the fully grouted rockbolts and the surface support.The rock mass is assumed to be elastic-brittle-plastic material,obeying the linear Mohr-Coulomb criterion or the non-linear Hoek-Brown criterion.According to the strain states of the tunnel wall at bolt and surface support installation and the relative magnitude between the bolt length and the plastic depth during the whole process,six cases are categorized upon solving the problem.Each case is divided into three stages due to the different effects of the active rockbolts and the passive surface support.The fictitious pressure is introduced to quantify the threedimensional(3D)effect of the tunnel face,and thus,the actual physical location along the tunnel axis of the analytical section can be considered.By using the bolt-rock strain compatibility and the rocksurface support displacement compatibility conditions,the solutions of longitudinal tunnel displacement and the reaction pressure of surface support along the tunnel axis are obtained.The proposed analytical solutions are validated by a series of 3D numerical simulations.Extensive parametric studies are conducted to examine the effect of the typical parameters of rockbolts and surface support on the tunnel displacement and the reaction pressure of the surface support under different rock conditions.The results show that the rockbolts are more effective in controlling the tunnel displacement than the surface support,which should be installed as soon as possible with a suitable length.For tunnels excavated in weak rocks or with restricted displacement control requirements,the surface support should also be installed or closed timely with a certain stiffness.The proposed method provides a convenient alternative approach for the optimization of rockbolts and surface support at the preliminary stage of tunnel design.

Path-Following Control With Obstacle Avoidance of Autonomous Surface Vehicles Subject to Actuator Faults

This paper investigates the path-following control problem with obstacle avoidance of autonomous surface vehicles in the presence of actuator faults,uncertainty and external disturbances.Autonomous surface vehicles inevitably suffer from actuator faults in complex sea environments,which may cause existing obstacle avoidance strategies to fail.To reduce the influence of actuator faults,an improved artificial potential function is constructed by introducing the lower bound of actuator efficiency factors.The nonlinear state observer,which only depends on measurable position information of the autonomous surface vehicle,is used to address uncertainties and external disturbances.By using a backstepping technique and adaptive mechanism,a path-following control strategy with obstacle avoidance and fault tolerance is designed which can ensure that the tracking errors converge to a small neighborhood of zero.Compared with existing results,the proposed control strategy has the capability of obstacle avoidance and fault tolerance simultaneously.Finally,the comparison results through simulations are given to verify the effectiveness of the proposed method.

Clay mineral compositions in the surface sediment of the Chanthaburi coast(northeastern Gulf of Thailand)and their implications on sediment provenance

Clay mineral composition represents an important tracer of sediment source area,migration processes,and paleoclimatic conditions.Clay mineral analysis was performed on 15 surface sediment samples collected from the coast of Chanthaburi,Thailand.Results show that the composition of clay minerals in the study area differs substantially from that in surrounding regions of the Gulf of Thailand.The clay minerals of the Chanthaburi coast are dominated by kaolinite(~56%),followed by smectite(~21%),illite(~14%),and low concentrations of chlorite(~8%).The average illite chemistry index and crystallinity are 0.93 and 0.32,respectively.Comparative analysis of the clay mineral composition of surface sediments in several typical areas around the Gulf of Thailand indicated that the clays of the Chanthaburi coast are mainly derived from parent rock weathering in the small watersheds of the Chanthaburi and Welu rivers and the surrounding islands.Terrestrial input from the northern coast of the Gulf of Thailand(excluding the Mekong River)was previously considered negligible;however,the present results indicate that such input has impact on the eastern Gulf of Thailand.The warm humid climatic conditions in Southeast Asia are the primary factors that affect the strong chemical weathering in the study area,followed by the nature of the parent rock.

Surface-modified Ag@Ru-P25 for photocatalytic CO_(2) conversion with high selectivity over CH_(4) formation at the solid–gas interface

Systematic optimization of the photocatalyst and investigation of the role of each component is important to maximizing catalytic activity and comprehending the photocatalytic conversion of CO_(2) reduction to solar fuels.A surface-modified Ag@Ru-P25 photocatalyst with H_(2)O_(2) treatment was designed in this study to convert CO_(2) and H_(2)O vapor into highly selective CH4.Ru doping followed by Ag nanoparticles(NPs)cocatalyst deposition on P25(TiO_(2))enhances visible light absorption and charge separation,whereas H_(2)O_(2) treatment modifies the surface of the photocatalyst with hydroxyl(–OH)groups and promotes CO_(2) adsorption.High-resonance transmission electron microscopy,X-ray photoelectron spectroscopy,X-ray absorption near-edge structure,and extended X-ray absorption fine structure techniques were used to analyze the surface and chemical composition of the photocatalyst,while thermogravimetric analysis,CO_(2) adsorption isotherm,and temperature programmed desorption study were performed to examine the significance of H_(2)O_(2) treatment in increasing CO_(2) reduction activity.The optimized Ag1.0@Ru1.0-P25 photocatalyst performed excellent CO_(2) reduction activity into CO,CH4,and C2H6 with a~95%selectivity of CH4,where the activity was~135 times higher than that of pristine TiO_(2)(P25).For the first time,this work explored the effect of H_(2)O_(2) treatment on the photocatalyst that dramatically increases CO_(2) reduction activity.

On the impact of grinding conditions in the flotation of semi-soluble salt-type mineral-containing ores driven by surface or particle geometry effects?

Grinding and flotation processes are often studied independently, despite the well-established grinding influence on flotation performance, which affects not only particle size and thus liberation but also shape and leads to complex changes in pulp chemistry affecting the particle surface properties relevant for selective bubble attachment. Yet, no study jointly investigated these possible causes and many are limited to single mineral flotation. We relate grinding conditions to changes in pulp chemistry and particle surface properties and assess their impact on upgrading. We studied three non-sulfide ores with different feed grades and valuables: scheelite, apatite, and fluorite. These were dry-, wet-, and wet conditionedground before flotation in a laboratory mechanical cell. Results were evaluated with bulk-and particle-specific methodologies. The selectivity of the process is higher after dry grinding for the fluorite and apatite ores and irrelevant for the scheelite ore. Variations in flotation kinetics of individual particles associated to their size and shape are not sufficient to explain these results. The higher concentration of Ca2+and Mg2+observed in the pulp after wet grinding, altering particle surface properties, better explains the phenomenon. Additionally, we demonstrate how particle shape impacts are system specific and related to both entrainment and true flotation.

Automatic Extraction Method of 3D Feature Guidelines for Complex Cultural Relic Surfaces Based on Point Cloud

Cultural relics line graphic serves as a crucial form of traditional artifact information documentation,which is a simple and intuitive product with low cost of displaying compared with 3D models.Dimensionality reduction is undoubtedly necessary for line drawings.However,most existing methods for artifact drawing rely on the principles of orthographic projection that always cannot avoid angle occlusion and data overlapping while the surface of cultural relics is complex.Therefore,conformal mapping was introduced as a dimensionality reduction way to compensate for the limitation of orthographic projection.Based on the given criteria for assessing surface complexity,this paper proposed a three-dimensional feature guideline extraction method for complex cultural relic surfaces.A 2D and 3D combined factor that measured the importance of points on describing surface features,vertex weight,was designed.Then the selection threshold for feature guideline extraction was determined based on the differences between vertex weight and shape index distributions.The feasibility and stability were verified through experiments conducted on real cultural relic surface data.Results demonstrated the ability of the method to address the challenges associated with the automatic generation of line drawings for complex surfaces.The extraction method and the obtained results will be useful for line graphic drawing,displaying and propaganda of cultural relics.

Gravity anomalies determined from mean sea surface model data over the Gulf of Mexico

With the improvements in the density and quality of satellite altimetry data,a high-precision and high-resolution mean sea surface model containing abundant information regarding a marine gravity field can be calculated from long-time series multi-satellite altimeter data.Therefore,in this study,a method was proposed for determining marine gravity anomalies from a mean sea surface model.Taking the Gulf of Mexico(15°–32°N,80°–100°W)as the study area and using a removal-recovery method,the residual gridded deflections of the vertical(DOVs)are calculated by combining the mean sea surface,mean dynamic topography,and XGM2019e_2159 geoid,and then using the inverse Vening-Meinesz method to determine the residual marine gravity anomalies from the residual gridded DOVs.Finally,residual gravity anomalies are added to the XGM2019e_2159 gravity anomalies to derive marine gravity anomaly models.In this study,the marine gravity anomalies were estimated with mean sea surface models CNES_CLS15MSS,DTU21MSS,and SDUST2020MSS and the mean dynamic topography models CNES_CLS18MDT and DTU22MDT.The accuracy of the marine gravity anomalies derived by the mean sea surface model was assessed based on ship-borne gravity data.The results show that the difference between the gravity anomalies derived by DTU21MSS and CNES_CLS18MDT and those of the ship-borne gravity data is optimal.With an increase in the distance from the coast,the difference between the gravity anomalies derived by mean sea surface models and ship-borne gravity data gradually decreases.The accuracy of the difference between the gravity anomalies derived by mean sea surface models and those from ship-borne gravity data are optimal at a depth of 3–4 km.The accuracy of the gravity anomalies derived by the mean sea surface model is high.

A Melamine–Dialdehyde Starch Wood Particleboard Surface Finish without Formaldehyde

Melamine-dialdehyde starch resins used for wood surface finishes have been developed.The reaction of melamine with dialdehyde starch has been shown to occur by FTIR and MALDI ToF spectrometry,with several oligomer species due to the reaction of the two materials being identified,and the resin thermal stability was studied by thermogravimetric analysis.The resins were prepared by two different procedures when it was realized that dialdehyde starch is sensitive to too high a temperature for prolonged times.The melamine-dialdehyde starch resins were applied on particleboard supports as a direct liquid surface finish and a resin-impregnated paper.The surface finishes were tested for adhesion by the cross-cut test,their initial sessile drop contact angle,and the contact angle evolution as a function of time.The best results were obtained by the resins catalyzed by 2% ammonium sulfate and applied to the support surface as a resin-impregnated paper hot pressed for 3 min at 200℃,although the results at 180℃ also looked promising.

Discontinuity development patterns and the challenges for 3D discrete fracture network modeling on complicated exposed rock surfaces

Natural slopes usually display complicated exposed rock surfaces that are characterized by complex and substantial terrain undulation and ubiquitous undesirable phenomena such as vegetation cover and rockfalls.This study presents a systematic outcrop research of fracture pattern variations in a complicated rock slope,and the qualitative and quantitative study of the complex phenomena impact on threedimensional(3D)discrete fracture network(DFN)modeling.As the studies of the outcrop fracture pattern have been so far focused on local variations,thus,we put forward a statistical analysis of global variations.The entire outcrop is partitioned into several subzones,and the subzone-scale variability of fracture geometric properties is analyzed(including the orientation,the density,and the trace length).The results reveal significant variations in fracture characteristics(such as the concentrative degree,the average orientation,the density,and the trace length)among different subzones.Moreover,the density of fracture sets,which is approximately parallel to the slope surface,exhibits a notably higher value compared to other fracture sets across all subzones.To improve the accuracy of the DFN modeling,the effects of three common phenomena resulting from vegetation and rockfalls are qualitatively analyzed and the corresponding quantitative data processing solutions are proposed.Subsequently,the 3D fracture geometric parameters are determined for different areas of the high-steep rock slope in terms of the subzone dimensions.The results show significant variations in the same set of 3D fracture parameters across different regions with density differing by up to tenfold and mean trace length exhibiting differences of 3e4 times.The study results present precise geological structural information,improve modeling accuracy,and provide practical solutions for addressing complex outcrop issues.

Response Surface Methodology-Based SERS for Determination of Gymnodimine

Gymnodimine (GYM), a fast-acting marine toxin, is destructive to aquaculture and human health through contaminated shellfish. The current detection methods in GYM have definite drawbacks in operation, such as the demand for delicate instruments and the consumption of time. Therefore, silver colloid was utilized as a surface-enhanced Raman scattering (SERS) desirable substrate for sensitive and rapid detection of GYM in lake and shellfish samples. The theoretical spectrum of GYM is calculated by density functional theory (DFT), and the substrate performance is evaluated by a rhodamine 6 G probe. Under the optimal SERS experimental condition calculated by the response surface methodology, the low limit of detection of 0.105 μM with R2 of 0.9873 and a broad linearity range of 0.1 - 10 μM was achieved for GYM detection. In addition, the substrate was satisfyingly applied to detect gymnodimine in the lake and shellfish matrix samples with LOD as low as 0.148 μM and 0.170 μM, respectively. These results demonstrated a promising SERS platform for detecting marine toxins in seafood for food safety and pharmaceutical research.