Numerical simulations of Atlantic meridional overturning circulation(AMOC)from OMIP experiments and its sensitivity to surface forcing

Atlantic meridional overturning circulation(AMOC)plays an important role in transporting heat meridionally in the Earth’s climate system and is also a key metrical tool to verify oceanic general circulation models.Two OMIP(Ocean Model Intercomparison Project phase 1 and 2)simulations with LICOM3(version 3 of the LASG/IAP Climate System Ocean Model)developed at the State Key Laboratory of Numerical Modeling for Atmospheric Sciences and Geophysical Fluid Dynamics(LASG),Institute of Atmospheric Physics(IAP),are compared in this study.Both simulations well reproduce the fundamental characteristics of the AMOC,but the OMIP1 simulation shows a significantly stronger AMOC than the OMIP2 simulation.Because the LICOM3 configurations are identical between these two experiments,any differences between them must be attributed to the surface forcing data.Further analysis suggests that sea surface salinity(SSS)differences should be mainly responsible for the enhanced AMOC in the OMIP1 simulation,but sea surface temperature(SST)also play an unignorable role in modulating AMOC.In the North Atlantic,where deep convection occurs,the SSS in OMIP1 is more saline than that in OMIP1.We find that in the major region of deep convection,the change of SSS has more significant effect on density than the change of SST.As a result,the SSS was more saline than that in OMIP2,leading to stronger deep convection and subsequently intensify the AMOC.We conduct a series of numerical experiments with LICOM3,and the results confirmed that the changes in SSS have more significant effect on the strength of AMOC than the changes in SST.

Experimental and numerical simulation study on forced ventilation and dust removal of coal mine heading surface

In order to study the problems of unreasonable airflow distribution and serious dust pollution in a heading surface,an experimental platform for forced ventilation and dust removal was built based on the similar principles.Through the similar experiment and numerical simulation,the distribution of airflow field in the roadway and the spatial and temporal evolution of dust pollution under the conditions of forced ventilation were determined.The airflow field in the roadway can be divided into three zones:jet zone,vortex zone and reflux zone.The dust concentration gradually decreases from the head to the rear of the roadway.Under the forced ventilation conditions,there is a unilateral accumulation of dust,with higher dust concentrations away from the ducts.The position of the equipment has an interception effect on the dust.The maximum error between the test value and the simulation result is 12.9%,which verifies the accuracy of the experimental results.The research results can provide theoretical guidance for the application of dust removal technology in coal mine.

Impact of Spin-up Forcing on Vegetation States Simulated by a Dynamic Global Vegetation Model Coupled with a Land Surface Model

A dynamic global vegetation model （DGVM） coupled with a land surface model （LSM） is generally initialized using a spin-up process to derive a physically-consistent initial condition. Spin-up forcing, which is the atmospheric forcing used to drive the coupled model to equilibrium solutions in the spin-up process, varies across earlier studies. In the present study, the impact of the spin-up forcing in the initialization stage on the fractional coverages （FCs） of plant functional type （PFT） in the subsequent simulation stage are assessed in seven classic climate regions by a modified Community Land Model’s Dynamic Global Vegetation Model （CLM-DGVM）. Results show that the impact of spin-up forcing is considerable in all regions except the tropical rainforest climate region （TR） and the wet temperate climate region （WM）. In the tropical monsoon climate region （TM）, the TR and TM transition region （TR-TM）, the dry temperate climate region （DM）, the highland climate region （H）, and the boreal forest climate region （BF）, where FCs are affected by climate non-negligibly, the discrepancies in initial FCs, which represent long-term cumulative response of vegetation to different climate anomalies, are large. Moreover, the large discrepancies in initial FCs usually decay slowly because there are trees or shrubs in the five regions. The intrinsic growth timescales of FCs for tree PFTs and shrub PFTs are long, and the variation of FCs of tree PFTs or shrub PFTs can affect that of grass PFTs.

Seasonal characteristics and forcing mechanisms of the surface Kuroshio branch intrusion into the South China Sea

Using observational data of Argos satellite-tracked drifters from 1988 to 2012, we analyzed seasonal characteristics of the surface Kuroshio branch(KB) intrusion into the South China Sea(SCS). The analysis results are as follows.The surface KB originates from the southern Balintang Channel(BLTC) and Babuyan Channel(BBYC). It begins in late September, reaches peak strength in November–December, and declines at the end of March. The mean speed of drifters along the KB path during their traverse of the Luzon Strait(LS) was 43% faster than during the two days before entering the LS for the flow originating from the southern BLTC, but there was a 24% increase in speed for the flow from the BBYC. The observations show that in winter, monthly-mean sea-level anomalies(SLAs) were positive southwest of Taiwan Island and extended to the northern LS. The SLAs were negative northwest of Luzon Island and extended to the southern LS, which acted like a pump, forcing a part of Kuroshio water westward into the SCS. The condition under which the KB forms was solved by a set of simplified motion equations. The results indicate that whether the KB can form depends upon the sea-level gradient at the central LS and region to the west, as well as the location, speed and direction of Kuroshio surface water when it enters the LS.

Assessment of aerosol effective radiative forcing and surface air temperature response over eastern China in CMIP5 models

The effective radiative forcing （ERF） and associated surface air temperature change over eastern China are estimated using multi-model results from CMIP5 （Coupled Model Intercomparison Project Phase 5）. The model results show that, relative to 1850, the multi-model and annual mean aerosol ERF for the year 2005 is -4.14 W m^-2 at the top of the atmosphere over eastern China （20°-45°N, 105°-122.5°E）. As a result of this ERF, the multi-model and annual mean surface air temperature change in eastern China during 1850-2005 is -1.05℃, leading to a climate sensitivity of 0.24℃/ （Wm^-2） in this region.

An Updated Estimation of Radiative Forcing due to CO_2 and Its Effect on Global Surface Temperature Change

New estimations of radiative forcing due to CO2 were calculated using updated concentration data of CO2 and a high-resolution radiative transfer model. The stratospheric adjusted radiative forcing （ARF） due to CO2 from the year 1750 to the updated year of 2010 was found to have increased to 1.95 W m-2, which was 17% larger than that of the IPCC＇s 4th Assessment Report because of the rapid increase in CO2 concentrations since 2005. A new formula is proposed to accurately describe the relationship between the ARF of CO2 and its concentration. Furthermore, according to the relationship between the ARF and surface temperature change, possible changes in equilibrium surface temperature were estimated under the scenarios that the concentration of CO2 increases to 1.5, 2, 2.5, 3, 3.5 and 4 times that of the concentration in the year 2008. The result was values of ＋2.2℃, ＋3.8℃, ＋5.1℃, ＋6.2℃, ＋7.1℃ and ＋8.0℃ respectively, based on a middle-level climate sensitivity parameter of 0.8 K （W m 3）-1. Non-equilibrium surface temperature changes over the next 500 years were also calculated under two kinds of emission scenarios （pulsed and sustained emissions） as a comparison, according to the Absolute Global Temperature change Potential （AGTP） of CO2. Results showed that CO2 will likely continue to contribute to global warming if no emission controls are imposed, and the effect on the Earth-atmosphere system will be difficult to restore to its original level.

Probe the Effects of Surface Adsorbates on ZnO Nanowire Conductivity using Dielectric Force Microscopy

Characterization of electric properties of nanomaterials usually involves fabricating field effect transistors （FET） and deriving materials properties from device performances. However, the quality of electrode contacts in FET devices heavily influences the device performance, which makes it difficult to obtain the intrinsic electric properties of nanomaterials. Dielectric force microscopy （DFM）, a contactless method developed recently, can detect the low-frequency dielectric responses of nanomaterials without electric contact, which avoids the influence of electric contact and can be used to study the intrinsic conductivity of nanomaterials. Here we study the influences of surface adsorbates on the conductivity of ZnO nanowires （NWs） by using FET and DFM methods. The conductivity of ZnO NW is much larger in N2 atmosphere than that in ambient environment as measured by FET device, which is further proven by DFM measurement that the ZnO NW exhibits larger dielectric response in N2 environment, and the influence of electrode contacts on measurement can be ruled out. Based on these results, it can be concluded that the adsorbates on ZnO NW surface highly influence the conductivity of ZnO NW rather than the electrode contact. This work also verifies the capability of DFM in measuring electric properties of nanomaterials.

Force measurement between mica surfaces in electrolyte solutions

The forces between two molecularly smooth mica surfaces are measured in monovalent and divalent cations electrolyte solutions by a surface force apparatus （SFA）. The properties of K＋, Na＋, and Mg2＋ between molecularly smooth mica surfaces are investigated. The Derjagui-Landau- Verwey-Overbeek （DLVO） force and the hydration force are detected in the experiment. The results show that in lower concentrations of a monovalent electrolyte solution （about 10-4 mol/L）, the force curves are completely in good agreement with those computed by the DLVO theory. However, additional short-range repulsive forces which deviate from the DLVO theory are observed when the concentrations of cations are above the critical bulk concentration, which is different for each electrolyte. The results show the properties of these cations on both the screening effect adsorbed on the mica surface and the hydration in solution. From the results, the interaction energy between two hydrated ions of potassium or sodium can also be estimated.

Elucidating Dominant Factors Affecting Land Surface Hydrological Simulations of the Community Land Model over China

In order to compare the impacts of the choice of land surface model(LSM)parameterization schemes,meteorological forcing,and land surface parameters on land surface hydrological simulations,and explore to what extent the quality can be improved,a series of experiments with different LSMs,forcing datasets,and parameter datasets concerning soil texture and land cover were conducted.Six simulations are run for the Chinese mainland on 0.1°×0.1°grids from 1979 to 2008,and the simulated monthly soil moisture(SM),evapotranspiration(ET),and snow depth(SD)are then compared and assessed against observations.The results show that the meteorological forcing is the most important factor governing output.Beyond that,SM seems to be also very sensitive to soil texture information;SD is also very sensitive to snow parameterization scheme in the LSM.The Community Land Model version 4.5(CLM4.5),driven by newly developed observation-based regional meteorological forcing and land surface parameters(referred to as CMFD_CLM4.5_NEW),significantly improved the simulations in most cases over the Chinese mainland and its eight basins.It increased the correlation coefficient values from 0.46 to 0.54 for the SM modeling and from 0.54 to 0.67 for the SD simulations,and it decreased the root-mean-square error(RMSE)from 0.093 to 0.085 for the SM simulation and reduced the normalized RMSE from 1.277 to 0.201 for the SD simulations.This study indicates that the offline LSM simulation using a refined LSM driven by newly developed observation-based regional meteorological forcing and land surface parameters can better model reginal land surface hydrological processes.

Adsorption and desorption behaviors of ssDNA molecules on mica surface by surface forces apparatus

An approach for studying the adsorption and desorption behaviors of single-stranded DNA（ ssDNA） molecules on the mica surface by the surface forces apparatus（ SFA） is reported,which can be used to characterize the precise thickness,configuration and mechanical properties of ssDNA layers on the mica surface at a certain buffer solution. The formation of ss DNA layers is first studied by tuning the ssDNA concentrations, and the experimental results indicate that the ss DNA concentration of 100 ng / μL is ideal for forming a ssDNA monolayer structure on the mica surface, and the hardwall value measured to be 1.04 nm under this circumstance is regarded as the thickness of the ssDNA monolayer confined on mica. The desorption behavior of ssDNA molecules from the mica surface is further studied by observing and comparing different shapes of the force-distance curves under certain conditions. It is found that the desorption of ss DNA molecules from the mica surface occurs as the monovalent salts are added into the gap buffer. It is inferred that the competition effect between monovalent and divalent salts can induce the release of ssDNA from substrate.The results also reveal that 10 mmol / L monovalent salts（ Na~＋）is sufficient for the desorption of ssDNA from mica. This work provides an applicable method to study the binding mechanism of ss DNA molecules on inorganic substrates.

AN IN SITU SURFACE COMPOSITE AND GRADIENT MATERIAL OF Al-Si ALLOY PRODUCED BY ELECTROMAGNETIC FORCE

Because of the different conductivities between the primary phase (low electric conduc tivity) and the metal melt, electromagnetic force scarcely acts on the primary phase. Thus, an electromagnetic repulsive force applied by the metal melt exerts on the pri mary phase when the movement of the melt in the direction of electromagnetic force is limited. As a result, the repulsive force exerts on the primary phase to push them to move in the direction opposite to that of the electromagnetic force when the metal melt with primary phase solidifies under an electromagnetic force field. Based on this, a new method for production of in situ surface composite and gradient material by electromagnetic force is proposed. An in situ primary Si reinforced surface composite of Al-15wt%Si alloy and gradient material of Al-l9wt%Si alloy were produced by this method. The microhardness of the primary Si is HV1320. The reinforced phase size is in the range from 40μm to 100μm. The wear resistance of Al-Si alloy gradient material can be more greatly increased than that of their matrix material.

Study of the Contact Force in Free-form Surfaces Compliant EDM Polishing by Robot

With an elastic negative pole being driven by ultra so nic vibration and being moved along the surface of work-piece compliantly by ro bot, a new kind of effective EDM, the compliant EDM, cuts the electrically condu ctive materials away and polishes work-piece of free-form surface. The study o f the contact force between the end of polishing tool and the surface of work-p iece is the key for the compliant EDM to study its cutting mechanism and to make better use of it. This paper makes a model for the contact force and verifies i t by experiments and simulation based on the theory of elastic body kinetics and dynamic stress concentration. The research work shows that this contact force i s caused by both the electrical impulsion of EDM and the mechanical force of ult rasonic vibration, the discharge frequency of compliant EDM has a much more clos er connection with the vibration frequency of polishing tool rather than the fre quency of ultrasonic vibration.

A New Dynamics Analysis Model for Five-Axis Machining of Curved Surface Based on Dimension Reduction and Mapping

The equipment used in various fields contains an increasing number of parts with curved surfaces of increasing size.Five-axis computer numerical control(CNC)milling is the main parts machining method,while dynamics analysis has always been a research hotspot.The cutting conditions determined by the cutter axis,tool path,and workpiece geometry are complex and changeable,which has made dynamics research a major challenge.For this reason,this paper introduces the innovative idea of applying dimension reduction and mapping to the five-axis machining of curved surfaces,and proposes an efficient dynamics analysis model.To simplify the research object,the cutter position points along the tool path were discretized into inclined plane five-axis machining.The cutter dip angle and feed deflection angle were used to define the spatial position relationship in five-axis machining.These were then taken as the new base variables to construct an abstract two-dimensional space and establish the mapping relationship between the cutter position point and space point sets to further simplify the dimensions of the research object.Based on the in-cut cutting edge solved by the space limitation method,the dynamics of the inclined plane five-axis machining unit were studied,and the results were uniformly stored in the abstract space to produce a database.Finally,the prediction of the milling force and vibration state along the tool path became a data extraction process that significantly improved efficiency.Two experiments were also conducted which proved the accuracy and efficiency of the proposed dynamics analysis model.This study has great potential for the online synchronization of intelligent machining of large surfaces.

Hydration film measurement on mica and coal surfaces using atomic force microscopy and interfacial interactions

The hydration film on particle surface plays an important role in bubble-particle adhesion in mineral flotation process. The thicknesses of the hydration films on natural hydrophobic coal and hydrophilic mica surfaces were measured directly by atomic force microscopy （AFM） based on the bending mode of the nominal constant compliance regime in AFM force curve in the present study. Surface and solid-liquid interfacial energies were calculated to explain the forming mechanism of the hydration film and atomic force microscopy data. The results show that there are significant differences in the structure and thickness of hydration films on coal and mica surfaces. Hydration film formed on mica surface with the thickness of 22.5 nm. In contrast, the bend was not detected in the nominal constant compliance regime. The van der Waals and polar interactions between both mica and coal and water molecules are characterized by an attractive effect, while the polar attractive free energy between water and mica （-87.36 mN/m） is significantly larger than that between water and coal （-32.89 mN/m）, which leads to a thicker and firmer hydration layer on the mica surface. The interfacial interaction free energy of the coal/water/bubble is greater than that of mica. The polar attractive force is large enough to overcome the repulsive van der Waals force and the low energy barrier of film rupture, achieving coal particle bubble adhesion with a total interfacial free energy of-56.30 mN/m.

Intermolecular and surface forces in atomic-scale manufacturing

Atomic and close-to-atomic scale manufacturing(ACSM)aims to provide techniques for manufacturing in various fields,such as circuit manufacturing,high energy physics equipment,and medical devices and materials.The realization of atomic scale material manipulation depending on the theoretical system of classical mechanics faces great challenges.Understanding and using intermolecular and surface forces are the basis for better designing of ACSM.Transformation of atoms based on scanning tunneling microscopy or atomic force microscopy(AFM)is an essential process to regulate intermolecular interactions.Self-assemble process is a thermodynamic process involving complex intermolecular forces.The competition of these interaction determines structure assembly and packing geometry.For typical nanomachining processes including AFM nanomachining and chemical mechanical polishing,the coupling of chemistry and stress(tribochemistry)assists in the removal of surface atoms.Furthermore,based on the principle of triboelectrochemistry,we expect a further reduction of the potential barrier,and a potential application in high-efficiency atoms removal and fabricating functional coating.Future fundamental research is proposed for achieving high-efficiency and high-accuracy manufacturing with the aiding of external field.This review highlights the significant contribution of intermolecular and surface forces to ACSM,and may accelerate its progress in the in-depth investigation of fundamentals.

Performance evaluation of minimum quantity lubrication by vege-table oil in terms of cutting force,cutting zone temperature,tool wear,job dimension and surface finish in turning AISI-1060 steel

In all machining processes, tool wear is a natural phenomenon and it leads to tool failure. The growing demands for high productivity of machining need use of high cutting velocity and feed rate. Such machining inherently produces high cutting temperature, which not only reduces tool life but also impairs the product quality. Metal cutting fluid changes the performance of machining operations because of their lubrication, cooling and chip flushing functions, but the use of cutting fluid has become more problematic in terms of both employee health and environmental pollution. The minimization of cutting fluid also leads to economical benefits by way of saving lubricant costs and workpiece/tool/machine cleaning cycle time. The concept of minimum quantity lubrication (MQL) has been suggested since a decade ago as a means of addressing the issues of environmental intru- siveness and occupational hazards associated with the airborne cutting fluid particles on factory shop floors. This paper deals with experimental investigation on the role of MQL by vegetable oil on cutting temperature, tool wear, surface roughness and dimen- sional deviation in turning AISI-1060 steel at industrial speed-feed combinations by uncoated carbide insert. The encouraging results include significant reduction in tool wear rate, dimensional inaccuracy and surface roughness by MQL mainly through reduction in the cutting zone temperature and favorable change in the chip-tool and work-tool interaction.

Generating micro/nanostructures on magnesium alloy surface using ultraprecision diamond surface texturing process

The lightness and high strength-to-weight ratio of the magnesium alloy have attracted more interest in various applications.However,micro/nanostructure generation on their surfaces remains a challenge due to the flammability and ignition.Motivated by this,this study proposed a machining process,named the ultraprecision diamond surface texturing process,to machine the micro/nanostructures on magnesium alloy surfaces.Experimental results showed the various microstructures and sawtooth-shaped nanostructures were successfully generated on the AZ31B magnesium alloy surfaces,demonstrating the effectiveness of this proposed machining process.Furthermore,sawtooth-shaped nanostructures had the function of inducing the optical effect and generating different colors on workpiece surfaces.The colorful letter and colorful flower image were clearly viewed on magnesium alloy surfaces.The corresponding cutting force,chip morphology,and tool wear were systematically investigated to understand the machining mechanism of micro/nanostructures on magnesium alloy surfaces.The proposed machining process can further improve the performances of the magnesium alloy and extend its functions to other fields,such as optics.

Surface Electromechanical Coupling on DLC Film with Conductive Atomic Force Microscope

Diamond-like carbon (DLC) film composed of microscopically insulation but microscopically a mixture of conducting (sp2) and insulating (sp3) phases was discussed on the local modification with a conductive atomic force microscope (C-APM). Especially, a topographic change was observed when a direct current (DC) bias-voltage was applied to the DLC film. Experimental results show that a nanoscale pit on DLC surface was formed when applying a positive 25 V on DLC film. According to the interacting force between CoCr-coated microelectronic scanning probe (MESP) tip and DLC surface, as well as the Sondheimer oscillation theory, the 'scalewing effect' of the pit was explained. Electromechanical coupling on DLC film suggested that the depth of pits increased with an increase of load applied to surface when the cantilever-deflected signal was less than a certain threshold voltage.

Probing the Interfacial Forces and Surface Interaction Mechanisms in Petroleum Production Processes

Despite the advances that have been made in renewable energy over the past decade,crude oil or petroleum remains one of the most important energy resources to the world.Petroleum production presents many challenging issues,such as the destabilization of complex oil-water emulsions,fouling phenomena on pipelines and other facilities,and water treatment.These problems are influenced by the molecular forces at the oil/water/solid/gas interfaces involved in relevant processes.Herein,we present an overview of recent advances on probing the interfacial forces in several petroleum production processes(e.g.,bitumen extraction,emulsion stabilization and destabilization,fouling and antifouling phenomena,and water treatment)by applying nanomechanical measurement technologies such as a surface forces apparatus(SFA)and an atomic force microscope(AFM).The interaction forces between bitumen and mineral solids or air bubbles in the surrounding fluid media determine the bitumen liberation and flotation efficiency in oil sands production.The stability of complex oil/water emulsions is governed by the forces between emulsion drops and particularly between interface-active species(e.g.,asphaltenes).Various oil components(e.g.,asphaltenes)and emulsion drops interact with different substrate surfaces(e.g.,pipelines or membranes),influencing fouling phenomena,oil-water separation,and wastewater treatment.Quantifying these intermolecular and interfacial forces has advanced the mechanistic understanding of these interfacial interactions,facilitating the development of advanced materials and technologies to solve relevant challenging issues and improve petroleum production processes.Remaining challenges and suggestions on future research directions in the field are also presented.

A flexible multi-body model of a surface miner for analyzing the interaction between rock-cutting forces and chassis vibrations

The discontinuous nature of rock cutting can easily cause unwanted vibrations in the structure of a surface miner.If these vibrations are not properly addressed,the related stress cycles can gradually damage the chassis resulting in fatigue failures.These events can seriously undermine the safety of operators and digging operations may be stopped for days,with an obvious economic impact.This work presents an analysis of the dynamics of a surface miner,focusing on the interaction between cutting machine dynamics and cutting forces,which is a new approach for this type of machine.For this purpose,the authors developed a numerical model of the cutting process made up of(1)a multi-body model of the cutting machine,which takes into account the chassis's flexibility;(2)a model of the rotating cutting head;and(3)a model of the interaction between the cutting head and rock,based on Shao's model.The model was compared with experimental results and then used to investigate the effects of cutting speed and cutting depth on the machine dynamics.