Exploitation technology of pressure relief coalbed methane in vertical surface wells in the Huainan coal mining area

Exploitation technology of pressure relief coalbed methane in vertical surface wells is a new method for exploration of gas and coalbed methane exploitation in mining areas with high concentrations of gas, where tectonic coal developed. Studies on vertical surface well technology in the Huainan Coal Mining area play a role in demonstration in the use of clean, new energy resources, preventing and reducing coal mine gas accidents and protecting the environment. Based on the practice of gas drainage engineering of pressure relief coalbed methane in vertical surface wells and combined with relative geological and exploration en- gineering theories, the design principles of design and structure of wells of pressure relief coalbed methane in vertical surface wells are studied. The effects of extraction and their causes are discussed and the impact of geological conditions on gas production of the vertical surface wells are analyzed. The results indicate that in mining areas with high concentrations of gas, where tectonic coal developed, a success rate of pressure relief coalbed methane in surface vertical well is high and single well production usually great. But deformation due to coal exploitation could damage boreholes and cause breaks in the connection between aquifers and bore-holes, which could induce a decrease, even a complete halt in gas production of a single well. The design of well site location and wellbore configuration are the key for technology. The development of the geological conditions for coalbed methane have a significant effect on gas production of coalbed methane wells.

Optimum location of surface wells for remote pressure relief coalbed methane drainage in mining areas

Based on engineering tests in the Huainan coal mining area,we studied alternative well location to improve the performance of surface wells for remote pressure relief of coalbed methane in mining areas.The key factors,affecting location and well gas production were analyzed by simulation tests for similar material.The exploitation results indicate that wells located in various positions on panels could achieve relatively better gas production in regions with thin Cenozoic layers,low mining heights and slow rate of longwall advancement,but their periods of gas production lasted less than 230 days,as opposed to wells in regions with thick Cenozoic layers,greater mining heights and fast rates of longwall advancement.Wells near panel margins achieved relatively better gas production and lasted longer than centerline wells.The rules of development of mining fractures in strata over panels control gas production of surface wells.Mining fractures located in areas determined by lines of compaction and the effect of mining are well developed and can be maintained for long periods of time.Placing the well at the end of panels and on the updip return airway side of panels,determined by lines of compaction and the effect of mining,would result in surface wells for remote pressure relief CBM obtaining their longest gas production periods and highest cumulative gas production.

Production Characteristics and the Control Factors of Surface Wells for Relieved Methane Drainage in the Huainan Mining Area

Based on the production data of a large number of surface drainage wells in the Huainan mining area,the present study shows that four types of typical production characteristics for relieved methane wells are recognized,of which the stable type for production and gas concentration is the most dominate,as determined by a comprehensive study on the volume and concentration of drained gases, as well as the stress changes of rocks influenced by mining.Some influence factors for the productive differences of the drainage wells were also been discussed.The results indicate that protective coal-seam mining has a significant effect on overlying strata,which promotes the development of pores and fractures of coal reservoirs for methane desorption and migration;however,the production and the stability of drainage wells are affected by deformation and damage of the overlying strata.The second distribution of strata stress is caused by mining engineering,and if the stress load is larger than the carrying capacity of the extraction well,the gas production would be influenced by the drainage well that has been damaged by rock movement.Furthermore,the case damage occurs first in the weak, lithologic interface by its special mechanical properties.The stability of drainage wells and the production status are also influenced by the different drilling techniques,uneven distribution of gas concentration,and combination of gob gas and methane from the protected layer.

Research on forced gas draining from coal seams by surface well drilling

Surface drilling was performed at the Luling Coal Mine,in Huaibei,to shorten the period required for gas draining.The experimental study was designed to reduce the cost of gas control by efficiently draining gas from the upper protected layer.The structural arraignment and technical principles of pressure relief via surface drilling are discussed.Results from the trial showed that gas drained from the surface system over a period of 10 months.The total amount of collected gas was 248.4 million m^3.The gas draining occurred in three stages：a growth period;a period of maximum gas production;and an attenuation period.The period of maximum gas production lasted for 4 months.During this time the methane concentration ranged from 60%to 90%and the average draining rate was 10.6 m^3/min.Combined with other methods of draining it was possible to drain 70.6%of the gas from middle coal seam groups.The amount of residual gas dropped to 5.2 m^3/ton,and the pressure of the residual gas fell to 0.53 MPa, thereby eliminating the outburst danger in the middle coal seam groups.The factors affecting pressure relief gas draining by surface drilling were analysed.

Research status and prospects of the fractal analysis of metal material surfaces and interfaces

As a mathematical analysis method,fractal analysis can be used to quantitatively describe irregular shapes with self-similar or self-affine properties.Fractal analysis has been used to characterize the shapes of metal materials at various scales and dimensions.Conventional methods make it difficult to quantitatively describe the relationship between the regular characteristics and properties of metal material surfaces and interfaces.However,fractal analysis can be used to quantitatively describe the shape characteristics of metal materials and to establish the quantitative relationships between the shape characteristics and various properties of metal materials.From the perspective of two-dimensional planes and three-dimensional curved surfaces,this paper reviews the current research status of the fractal analysis of metal precipitate interfaces,metal grain boundary interfaces,metal-deposited film surfaces,metal fracture surfaces,metal machined surfaces,and metal wear surfaces.The relationship between the fractal dimensions and properties of metal material surfaces and interfaces is summarized.Starting from three perspectives of fractal analysis,namely,research scope,image acquisition methods,and calculation methods,this paper identifies the direction of research on fractal analysis of metal material surfaces and interfaces that need to be developed.It is believed that revealing the deep influence mechanism between the fractal dimensions and properties of metal material surfaces and interfaces will be the key research direction of the fractal analysis of metal materials in the future.

Effects of Aerosol Vertical Inhomogeneity on the Upwelling Radiance and Satellite Remote Sensing of Surface Reflectance

There are two widely used radiative models without consideration of aerosol inhomogeneity for satellite remote sensing application, the Homogeneous Model and the Two-layer Model with aerosol in the lower layer. In this paper, effects of the aerosol vertical inhomogeneity on upwelling radiance and satellite remote sensing of surface reflectance are analyzed through numerical simulations by using two models. As shown in the simulations by using 24 representative aerosol models, there is often a considerably large error in upwel-ling radiance calculated by two models (Homogeneous and Two-layer) for the short wavelength channel with strong molecular scattering, owing to the difference between molecular and aerosol scattering proper-ties. For the long wavelength channel, the error is small if aerosol optical parameters are less variable with height, but it could also be significant if there are aerosol layers with different scattering phase functions and single scattering albedo. The radiance errors by the Homogeneous Model and the Two-layer Model can be up to 31.4% and 31.5% for the clean atmosphere, and in case of turbid atmosphere 67.8% and 59.2%, respectively. The radiance error could result in a large uncertainty of surface reflectance retrievals, especially for the short wavelength channel and the strongly absorbing aerosol. For the turbid atmosphere with strong-ly absorbing aerosol, the Homogeneous Model and the Two-layer Model are not suitable for atmospheric correction application. Key words Satellite remote sensing - Aerosol inhomogeneity - Surface reflectance - Radiance

Surface diffuse discharge mechanism of well-aligned atmospheric pressure microplasma arrays

A stable and homogeneous well-aligned air microplasma device for application at atmospheric pressure is designed and its electrical and optical characteristics are investigated. Current-voltage measurements and intensified charge coupled device （ICCD） images show that the well-aligned air microplasma device is able to generate a large-area and homogeneous discharge at the applied voltages ranging from 12 kV to 14 kV, with a repetition frequency of 5 kHz, which is attributed to the diffusion effect of plasma on dielectric surface. Moreover, this well-aligned microplasma device may result in the uniform and large-area surface modification of heat-sensitive PET polymers without damage, such as optimization in hydrophobicity and biocompatibility. In the biomedical field, the utility of this well-aligned microplasma device is further testified. It proves to be very efficient for the large-area and uniform inactivation of E. coli cells with a density of 103/cm2 on LB agar plate culture medium, and inactivation efficiency can reach up to 99% for 2-min treatment.

An Asthenospheric Upwelling Beneath Central Mongolia——Implications for Intraplate Surface Uplift and Volcanism

Intraplate processes,such as continental surface uplift and intraplate volcanism,are enigmatic and the underlying mechanisms responsible are not fully understood.Central Mongolia is an ideal natural laboratory for studying such processes because of its location in the continental interior far from tectonic plate boundaries.

Modeling of Surface Tension and Viscosity for Non-electrolyte Systems by Means of the Equation of State for Square-well Chain Fluids with Variable Interaction Range

The equation of state(EOS)for square-well chain fluid with variable range(SWCF-VR) developed in our previous work based on statistical mechanical theory for chemical association is employed for the correlations of surface tension and viscosity of common fluids and ionic liquids(ILs).A model of surface tension for multi-component mixtures is presented by combining the SWCF-VR EOS and the scaled particle theory and used to produce the surface tension of binary and ternary mixtures.The predicted surface tensions are in excellent agreement with the experimental data with an overall average absolute relative deviation(AAD)of 0.36%.A method for the calculation of dynamic viscosity of common fluids and ILs at high pressure is presented by combining Eyring’s rate theory of viscosity and the SWCF-VR EOS.The calculated viscosities are in good agreement with the experimental data with the overall AAD of 1.44% for 14 fluids in 84 cases.The salient feature is that the molecular parameters used in these models are self-consistent and can be applied to calculate different thermodynamic properties such as pVT,vapor-liquid equilibrium,caloric properties,surface tension,and viscosity.

A Self-Consistent Model on Cylindrical Monopole Plasma Antenna Excited by Surface Wave Based on the Maxwell-Boltzmann Equation

The paper analyzes the motion of electron in plasma antenna and the distribution of electromagnetic field power around the plasma antenna, and proposes a self-consistent model according to the structure of cylindrical monopole plasma antenna excited by surface wave;calculation of the model is based on Maxwell-Boltzmann equation and gas molecular dynamics theory. The calculation results show that this method can reflect the relationships between the external excitation power, gas pressure, discharge current and the characteristic of plasma. It is an accurate method to predicate and calculate the parameters of plasma antenna.

Convection of Maxwell fluid over stretching porous surface with heat source/sink in presence of nanoparticles:Lie group analysis

The convection of a Maxwell fluid over a stretching porous surface with a heat source/sink in the presence of nanoparticles is investigated. The Lie symmetry group transformations are used to convert the boundary layer equations into coupled nonlinear ordinary differential equations. The ordinary differential equations are solved numerically by the Bvp4c with MATLAB, which is a collocation method equivalent to the fourth-order mono-implicit Runge-Kutta method. Furthermore, more attention is paid to the effects of the physical parameters, especially the parameters related to nanoparticles, on the temperature and concentration distributions with consideration of permeability and the heat source/sink.

The effect of the attractive well of the potential energy surface for Ne-HC1 on rotationally inelastic partial wave cross sections

An interaction potential of the Ne-HC1 van der Waals complex is obtained by utilizing the Huxley analytic potential function to fit the accurate interaction energy data, which have been computed at the coupled cluster singles and doubles including connected triple excitations level and with the augmented correlation consistent polarized valence quintuple zeta basis set extended with a set of 3s3p2dlflg mid-bond functions [CCSD （T）/aug-cc-pV5Z-33211]. The close coupling calculation of state-to-state partial cross sections for collision of Ne with HC1 is first performed by employing the fitted interaction potential. This calculation is performed at the incident energies： 40, 60, 75 and 100 meV, separately. The effects of the long-range attractive and the short-range anisotropic interactions on the inelastic state-to-state partial cross sections are discussed in detail. Two maxima are present in the rotationally inelastic partial cross sections and they originate from different mechanisms.

Time–space dependent fractional boundary layer flow of Maxwell fluid over an unsteady stretching surface

Fractional boundary layer flow of Maxwell fluid on an unsteady stretching surface was investigated. Time-space dependent fractional derivatives are introduced into the constitutive equations of the fluid. We developed and solved the governing equations using explicit finite difference method and the L1- algorithm as well as shifted Grunwald-Letnikov formula. The effects of fractional parameters, relaxation parameter, Reynolds number, and unsteadiness parameter on the velocity behavior and characteristics of boundary layer thickness and skin friction were analyzed. Results obtained indicate that the behavior of boundary layer of viscoelastic fluid strongly depends on time-space fractional parameters. Increases of time fractional derivative parameter and relaxation parameter cause a decrease of velocity while boundary layer thickness increase, but the space fractional derivative parameter and fractional Reynolds number have the opposite effects.

Surface-modified Ag@Ru-P25 for photocatalytic CO_(2) conversion with high selectivity over CH_(4) formation at the solid–gas interface

Systematic optimization of the photocatalyst and investigation of the role of each component is important to maximizing catalytic activity and comprehending the photocatalytic conversion of CO_(2) reduction to solar fuels.A surface-modified Ag@Ru-P25 photocatalyst with H_(2)O_(2) treatment was designed in this study to convert CO_(2) and H_(2)O vapor into highly selective CH4.Ru doping followed by Ag nanoparticles(NPs)cocatalyst deposition on P25(TiO_(2))enhances visible light absorption and charge separation,whereas H_(2)O_(2) treatment modifies the surface of the photocatalyst with hydroxyl(–OH)groups and promotes CO_(2) adsorption.High-resonance transmission electron microscopy,X-ray photoelectron spectroscopy,X-ray absorption near-edge structure,and extended X-ray absorption fine structure techniques were used to analyze the surface and chemical composition of the photocatalyst,while thermogravimetric analysis,CO_(2) adsorption isotherm,and temperature programmed desorption study were performed to examine the significance of H_(2)O_(2) treatment in increasing CO_(2) reduction activity.The optimized Ag1.0@Ru1.0-P25 photocatalyst performed excellent CO_(2) reduction activity into CO,CH4,and C2H6 with a~95%selectivity of CH4,where the activity was~135 times higher than that of pristine TiO_(2)(P25).For the first time,this work explored the effect of H_(2)O_(2) treatment on the photocatalyst that dramatically increases CO_(2) reduction activity.

Triboelectric‘electrostatic tweezers'for manipulating droplets on lubricated slippery surfaces prepared by femtosecond laser processing

The use of‘Electrostatic tweezers'is a promising tool for droplet manipulation,but it faces many limitations in manipulating droplets on superhydrophobic surfaces.Here,we achieve noncontact and multifunctional droplet manipulation on Nepenthes-inspired lubricated slippery surfaces via triboelectric electrostatic tweezers(TETs).The TET manipulation of droplets on a slippery surface has many advantages over electrostatic droplet manipulation on a superhydrophobic surface.The electrostatic field induces the redistribution of the charges inside the neutral droplet,which causes the triboelectric charged rod to drive the droplet to move forward under the electrostatic force.Positively or negatively charged droplets can also be driven by TET based on electrostatic attraction and repulsion.TET enables us to manipulate droplets under diverse conditions,including anti-gravity climb,suspended droplets,corrosive liquids,low-surface-tension liquids(e.g.ethanol with a surface tension of 22.3 mN·m^(-1)),different droplet volumes(from 100 nl to 0.5 ml),passing through narrow slits,sliding over damaged areas,on various solid substrates,and even droplets in an enclosed system.Various droplet-related applications,such as motion guidance,motion switching,droplet-based microreactions,surface cleaning,surface defogging,liquid sorting,and cell labeling,can be easily achieved with TETs.

El Niño and the AMO Sparked the Astonishingly Large Margin of Warming in the Global Mean Surface Temperature in 2023

In 2023,the majority of the Earth witnessed its warmest boreal summer and autumn since 1850.Whether 2023 will indeed turn out to be the warmest year on record and what caused the astonishingly large margin of warming has become one of the hottest topics in the scientific community and is closely connected to the future development of human society.We analyzed the monthly varying global mean surface temperature(GMST)in 2023 and found that the globe,the land,and the oceans in 2023 all exhibit extraordinary warming,which is distinct from any previous year in recorded history.Based on the GMST statistical ensemble prediction model developed at the Institute of Atmospheric Physics,the GMST in 2023 is predicted to be 1.41℃±0.07℃,which will certainly surpass that in 2016 as the warmest year since 1850,and is approaching the 1.5℃ global warming threshold.Compared to 2022,the GMST in 2023 will increase by 0.24℃,with 88%of the increment contributed by the annual variability as mostly affected by El Niño.Moreover,the multidecadal variability related to the Atlantic Multidecadal Oscillation(AMO)in 2023 also provided an important warming background for sparking the GMST rise.As a result,the GMST in 2023 is projected to be 1.15℃±0.07℃,with only a 0.02℃ increment,if the effects of natural variability—including El Niño and the AMO—are eliminated and only the global warming trend is considered.

Analysis of the interaction between bolt-reinforced rock and surface support in tunnels based on convergence-confinement method

To investigate the interaction of the bolt-reinforced rock and the surface support,an analytical model of the convergence-confinement type is proposed,considering the sequential installation of the fully grouted rockbolts and the surface support.The rock mass is assumed to be elastic-brittle-plastic material,obeying the linear Mohr-Coulomb criterion or the non-linear Hoek-Brown criterion.According to the strain states of the tunnel wall at bolt and surface support installation and the relative magnitude between the bolt length and the plastic depth during the whole process,six cases are categorized upon solving the problem.Each case is divided into three stages due to the different effects of the active rockbolts and the passive surface support.The fictitious pressure is introduced to quantify the threedimensional(3D)effect of the tunnel face,and thus,the actual physical location along the tunnel axis of the analytical section can be considered.By using the bolt-rock strain compatibility and the rocksurface support displacement compatibility conditions,the solutions of longitudinal tunnel displacement and the reaction pressure of surface support along the tunnel axis are obtained.The proposed analytical solutions are validated by a series of 3D numerical simulations.Extensive parametric studies are conducted to examine the effect of the typical parameters of rockbolts and surface support on the tunnel displacement and the reaction pressure of the surface support under different rock conditions.The results show that the rockbolts are more effective in controlling the tunnel displacement than the surface support,which should be installed as soon as possible with a suitable length.For tunnels excavated in weak rocks or with restricted displacement control requirements,the surface support should also be installed or closed timely with a certain stiffness.The proposed method provides a convenient alternative approach for the optimization of rockbolts and surface support at the preliminary stage of tunnel design.

Surface Patterning of Metal Zinc Electrode with an In‑Region Zincophilic Interface for High‑Rate and Long‑Cycle‑Life Zinc Metal Anode

The undesirable dendrite growth induced by non-planar zinc(Zn)deposition and low Coulombic efficiency resulting from severe side reactions have been long-standing challenges for metallic Zn anodes and substantially impede the practical application of rechargeable aqueous Zn metal batteries(ZMBs).Herein,we present a strategy for achieving a high-rate and long-cycle-life Zn metal anode by patterning Zn foil surfaces and endowing a Zn-Indium(Zn-In)interface in the microchannels.The accumulation of electrons in the microchannel and the zincophilicity of the Zn-In interface promote preferential heteroepitaxial Zn deposition in the microchannel region and enhance the tolerance of the electrode at high current densities.Meanwhile,electron aggregation accelerates the dissolution of non-(002)plane Zn atoms on the array surface,thereby directing the subsequent homoepitaxial Zn deposition on the array surface.Consequently,the planar dendrite-free Zn deposition and long-term cycling stability are achieved(5,050 h at 10.0 mA cm^(−2) and 27,000 cycles at 20.0 mA cm^(−2)).Furthermore,a Zn/I_(2) full cell assembled by pairing with such an anode can maintain good stability for 3,500 cycles at 5.0 C,demonstrating the application potential of the as-prepared ZnIn anode for high-performance aqueous ZMBs.

Correlation of periodontal inflamed surface area with glycated hemoglobin,interleukin-6 and lipoprotein(a)in type 2 diabetes with retinopathy

BACKGROUND The two-way relationship between periodontitis and type 2 diabetes mellitus(T2DM)is well established.Prolonged hyperglycemia contributes to increased periodontal destruction and severe periodontitis,accentuating diabetic complications.An inflammatory link exists between diabetic retinopathy(DR)and periodontitis,but the studies regarding this association and the role of lipoprotein(a)[Lp(a)]and interleukin-6(IL-6)in these conditions are scarce in the literature.AIM To determine the correlation of periodontal inflamed surface area(PISA)with glycated Hb(HbA1c),serum IL-6 and Lp(a)in T2DM subjects with retinopathy.METHODS This cross-sectional study comprised 40 T2DM subjects with DR and 40 T2DM subjects without DR.All subjects were assessed for periodontal parameters[bleeding on probing(BOP),probing pocket depth,clinical attachment loss(CAL),oral hygiene index-simplified,plaque index(PI)and PISA],and systemic parameters[HbA1c,fasting plasma glucose and postprandial plasma glucose,fasting lipid profile,serum IL-6 and serum Lp(a)].RESULTS The proportion of periodontitis in T2DM with and without DR was 47.5%and 27.5%respectively.Severity of periodontitis,CAL,PISA,IL-6 and Lp(a)were higher in T2DM with DR group compared to T2DM without DR group.Significant difference was observed in the mean percentage of sites with BOP between T2DM with DR(69%)and T2DM without DR(41%),but there was no significant difference in PI(P>0.05).HbA1c was positively correlated with CAL(r=0.351,P=0.001),and PISA(r=0.393,P≤0.001)in study subjects.A positive correlation was found between PISA and IL-6(r=0.651,P<0.0001);PISA and Lp(a)(r=0.59,P<0.001);CAL and IL-6(r=0.527,P<0.0001)and CAL and Lp(a)(r=0.631,P<0.001)among study subjects.CONCLUSION Despite both groups having poor glycemic control and comparable plaque scores,the periodontal parameters were higher in DR as compared to T2DM without DR.Since a bidirectional link exists between periodontitis and DM,the presence of DR may have contributed to the severity of periodontal destruction and periodontitis may have influenced the progression of DR.

A facile strategy for tuning the density of surface-grafted biomolecules for melt extrusion-based additive manufacturing applications

Melt extrusion-based additive manufacturing(ME-AM)is a promising technique to fabricate porous scaffolds for tissue engi-neering applications.However,most synthetic semicrystalline polymers do not possess the intrinsic biological activity required to control cell fate.Grafting of biomolecules on polymeric surfaces of AM scaffolds enhances the bioactivity of a construct;however,there are limited strategies available to control the surface density.Here,we report a strategy to tune the surface density of bioactive groups by blending a low molecular weight poly(ε-caprolactone)5k(PCL5k)containing orthogonally reactive azide groups with an unfunctionalized high molecular weight PCL75k at different ratios.Stable porous three-dimensional(3D)scaf-folds were then fabricated using a high weight percentage(75 wt.%)of the low molecular weight PCL 5k.As a proof-of-concept test,we prepared films of three different mass ratios of low and high molecular weight polymers with a thermopress and reacted with an alkynated fluorescent model compound on the surface,yielding a density of 201-561 pmol/cm^(2).Subsequently,a bone morphogenetic protein 2(BMP-2)-derived peptide was grafted onto the films comprising different blend compositions,and the effect of peptide surface density on the osteogenic differentiation of human mesenchymal stromal cells(hMSCs)was assessed.After two weeks of culturing in a basic medium,cells expressed higher levels of BMP receptor II(BMPRII)on films with the conjugated peptide.In addition,we found that alkaline phosphatase activity was only significantly enhanced on films contain-ing the highest peptide density(i.e.,561 pmol/cm^(2)),indicating the importance of the surface density.Taken together,these results emphasize that the density of surface peptides on cell differentiation must be considered at the cell-material interface.Moreover,we have presented a viable strategy for ME-AM community that desires to tune the bulk and surface functionality via blending of(modified)polymers.Furthermore,the use of alkyne-azide“click”chemistry enables spatial control over bioconjugation of many tissue-specific moieties,making this approach a versatile strategy for tissue engineering applications.