Modeling of multiphase flow in low permeability porous media:Effect of wettability and pore structure properties

Multiphase flow in low permeability porous media is involved in numerous energy and environmental applications.However,a complete description of this process is challenging due to the limited modeling scale and the effects of complex pore structures and wettability.To address this issue,based on the digital rock of low permeability sandstone,a direct numerical simulation is performed considering the interphase drag and boundary slip to clarify the microscopic water-oil displacement process.In addition,a dual-porosity pore network model(PNM)is constructed to obtain the water-oil relative permeability of the sample.The displacement efficiency as a recovery process is assessed under different wetting and pore structure properties.Results show that microscopic displacement mechanisms explain the corresponding macroscopic relative permeability.The injected water breaks through the outlet earlier with a large mass flow,while thick oil films exist in rough hydrophobic surfaces and poorly connected pores.The variation of water-oil relative permeability is significant,and residual oil saturation is high in the oil-wet system.The flooding is extensive,and the residual oil is trapped in complex pore networks for hydrophilic pore surfaces;thus,water relative permeability is lower in the water-wet system.While the displacement efficiency is the worst in mixed-wetting systems for poor water connectivity.Microporosity negatively correlates with invading oil volume fraction due to strong capillary resistance,and a large microporosity corresponds to low residual oil saturation.This work provides insights into the water-oil flow from different modeling perspectives and helps to optimize the development plan for enhanced recovery.

Application of 3-D Geoscience Modeling Technology for the Estimation of Solid Mineral Reserves

Applying new approaches, methods, and technologies for the estimation of reserves can effectively improve the efficiency and accuracy of assessments of solid mineral resources. After analyzing the development of 3-D geoscience modeling technology （3-D GMT）, this paper discusses the application of 3-D GMT for the estimation of solid mineral reserves, emphatically introducing its workflow and two key technologies, 3-D orebody surface modeling, and property modeling. Moreover, the paper analyzes the limitations of traditional methods, such as the section method and geological block method, and points out the advantages of 3-D GMT： building more accurate 3-D orebody models, expressing the internal inhomogeneous attributes of an orebody, reducing the potential for errors in the estimation of reserves, and implementing dynamic estimations of reserves.

Parameter identification and global sensitivity analysis of Xin'anjiang model using meta-modeling approach

Parameter identification, model calibration, and uncertainty quantification are important steps in the model-building process, and are necessary for obtaining credible results and valuable information. Sensitivity analysis of hydrological model is a key step in model uncertainty quantification, which can identify the dominant parameters, reduce the model calibration uncertainty, and enhance the model optimization efficiency. There are, however, some shortcomings in classical approaches, including the long duration of time and high computation cost required to quantitatively assess the sensitivity of a multiple-parameter hydrological model. For this reason, a two-step statistical evaluation framework using global techniques is presented. It is based on （1） a screening method （Morris） for qualitative ranking of parameters, and （2） a variance-based method integrated with a meta-model for quantitative sensitivity analysis, i.e., the Sobol method integrated with the response surface model （RSMSobol）. First, the Morris screening method was used to qualitatively identify the parameters＇ sensitivity, and then ten parameters were selected to quantify the sensitivity indices. Subsequently, the RSMSobol method was used to quantify the sensitivity, i.e., the first-order and total sensitivity indices based on the response surface model （RSM） were calculated. The RSMSobol method can not only quantify the sensitivity, but also reduce the computational cost, with good accuracy compared to the classical approaches. This approach will be effective and reliable in the global sensitivity analysis of a complex large-scale distributed hydrological model.

Statistical Modeling Studies of Iron Recovery from Red Mud Using Thermal Plasma

Optimization studies of plasma smelting of red mud were carried out. Reduction of the dried red mud fines was done in an extended arc plasma reactor to recover the pig iron. Lime grit and low ash metallurgical （LAM） coke were used as the flux and reductant, respectively. 2level factorial design was used to study the influence of all parameters on the responses. Response surface modeling was done with the data obtained from statistically designed experiments. Metal recovery at optimum parameters was found to be 79.52%.

Subdivision surface modeling system based on arbitrary topological curves network and combined subdivision

Arbitrary topological curve network has no restriction in topology structure,so it has more powerful representing ability in defining complex surfaces.A complex surface modeling system is presented based on arbitrary topological curve network and the improved combined subdivision method,its functions including creating and editing curve network,and generating and modifying curve network＇s interpolated surface.This modeling system can be used to the process of products＇concept design,and its applications is also significant to the development of subdivision method.

PROTOTYPE SURFACE MICRO- PRECISION IN FUSED DEPOSITION MODELING PROCESS

To aim at prototype parts fabricated with fused deposition modeling （FDM） process, the problems how to improve and enhance their surface micro-precision are studied. The producing mechanism of surface roughness is explained with three aspects concretely including the principle error of rapid prototyping （RP） process, the inherent characteristics of FDM process, and some mi- cro-scratches on the surface of the extruded fiber. Based on the micro-characters of section shape of the FDM prototype, a physical model reflecting the outer shape characters is abstracted. With the physical simplified and deduced, the evaluating equations of surface roughness are acquired. According to the FDM sample parts with special design for experimental measurement, the real surface roughness values of different inclined planes are obtained. And the measuring values of surface roughness are compared with the calculation values. Furthermore, the causes of surface roughness deviation between measuring values and calculation values are respectively analyzed and studied. With the references of analytic conclusions, the measuring values of the experimental part surface are revised, and the revised values nearly accord with the calculation values. Based on the influencing principles of FDM process parameters and special post processing of FDM prototype parts, some concrete measures are proposed to reduce the surface roughness of FDM parts, and the applying effects are better.

Three-Component Model for Bidirectional Reflection Distribution Function of Thermal Coating Surfaces

We present a bidirectional reflection distribution function （BRDF） model for thermal coating surfaces based on a three-component reflection assumption, in which the specular reflection is given according to the microfacet theory and Snell＇s law, the multiple reflection is considered Nth cosine distributed, and the volume scattering is uniformly distributed in reflection angles according to the experimental results. This model describes the reflection characteristics of thermal coating surfaces more completely and reasonably. Simulation and measurement results of two thermal coating samples SR107 and S781 are given to validate that this three-component model significantly improves the modeling accuracy for thermal coating surfaces compared with the existing BRDF models.

Application Study on 3D Modeling of Axial Compressor Blades Based on CFD and CAD

A new method for design of turbomachinery blades is presented. The parameters of a compressor blade are created from the Computational Fluid Dynamics （CFD） software CFX-BladeGen, and are inputted to the Computer Aided Design （CAD） software UG for building a curve surface model to create an entity model in UG. The result shows that the blade model is favorable from the entity effect and reflection analysis and the model process is useful for the CAD model creation of turbomachinery blades.

An Effective Surface Modeling Method for Car Styling from a Side-View Image

We introduce an almost-automatic technique for generating 3D car styling surface models based on a single side-view image. Our approach combines the prior knowledge of car styling and deformable curve network model to obtain an automatic modeling process. Firstly, we define the consistent parameterized curve template for 2D and 3D case respectivelyby analyzingthe characteristic lines for car styling. Then, a semi-automatic extraction from a side-view car image is adopted. Thirdly, statistic morphable model of 3D curve network isused to get the initial solution with sparse point constraints.Withonly afew post-processing operations, the optimized curve network models for creating surfaces are obtained. Finally, the styling surfaces are automatically generated using template-based parametric surface modeling method. More than 50 3D curve network models are constructed as the morphable database. We show that this intelligent modeling toolsimplifiesthe exhausted modeling task, and also demonstratemeaningful results of our approach.

An angular cutoff composite model for investigation on electromagnetic scattering from two-dimensional rough sea surfaces

Based on the local configuration angle division to select the corresponding method for electromagnetic scattering calculation from rough sea surface, this paper presents an angular cutoff composite model： when the local scattered angle is in the specular region that is given by an approximately 20 degrees cone around the specular direction, the Kirchhoff approximation is applied to evaluate the specular reflection, which dominates the total scattering in this region; the small perturbation method is employed to handle the diffuse reflection which is predominant as the local scattered angle is situated out of the specular region. Numerical results are compared with those of experimental and theoretical models in several configurations as a function of incident angle, wind speed, wind direction. The comparison of numerical results of other experimental and theoretical models in several configurations shows that the new composite model is robust to give accurate numerical evaluations for the sea surface scattering.

Research into Freedom Surface Modeling System of Double Beta Spline in Space

In this paper, we present the double Beta spline curved surface which is controlled by double parameters including the algorithm principles, the treatment of boundary conditions, the alternation of projection, the algorithms of elimination hiddle line, the process to display and the primiples to produce the shaded curved surface. Based on all the above, a freedom surface modeling system (FSMS) is designed and some examples developed on FSMS are verified and analyzed.

Continuities of Progressive and Mixing Algorithm for Surface Modeling and Editing

The progressive and mixing algorithm(PAMA) is a method for surface modeling and editing,which is developed for effective and flexible applications in many environments,such as computer-aided design(CAD) and computer-aided geometric design(CAGD).In this paper,the construction scheme and continuities of PAMA are discussed,which provide a mathematics analysis of PAMA.The analysis and results show that the PAMA provides a new method of surface modeling and editing with four more degrees of freedom for designers to manipulate a 3D object.

Coupling Modeling for Functional Surface of Electronic Equipment

High performance electromechanical equipment is widely used in various fields, such as national defense, industry and so on [ 1]. In addition, the technical level of high performance electromechanical equipment is the embodiment of the national level of science and technology.

A NEW MODEL FOR PHYSICAL ADSORPTION ON SOLID SURFACES

The principal assumptions about equivalence and energy distribution of the asdorption sites on solidsurfaces used by Langmuir for deriving the equation of monomolecular adsorption are generalized and anew physical adsorption model is proposed and tested with experimental data published in literature.Themodels of Langmuir,Freundlich,Temkin etc.are only the special cases.Assuming uniform density distributionof adsorption energy,the isotherm equation is given asn=K.1n[1+（bop）1/Mor n=K.1n[1+（boC）1/M]where n is the amount of adsorption per unit weight or area of solid p or C is tbe pressure of gas or the concen-tration of solution respectively.K,bo,M are constants with physical meanings as described in this paper.This equation can be used over wide range to quantitatively represent the five types of physical adsorptionclassified by Brunauer.

REVERSE MODELING FOR CONIC BLENDING FEATURE

A novel method to extract conic blending feature in reverse engineering is presented. Different from the methods to recover constant and variable radius blends from unorganized points, it contains not only novel segmentation and feature recognition techniques, but also bias corrected technique to capture more reliable distribution of feature parameters along the spine curve. The segmentation depending on point classification separates the points in the conic blend region from the input point cloud. The available feature parameters of the cross-sectional curves are extracted with the processes of slicing point clouds with planes, conic curve fitting, and parameters estimation and compensation, The extracted parameters and its distribution laws are refined according to statistic theory such as regression analysis and hypothesis test. The proposed method can accurately capture the original design intentions and conveniently guide the reverse modeling process. Application examples are presented to verify the high precision and stability of the proposed method.

Modeling of Inner Surface Modification of a Cylindrical Tube by Plasma-Based Low-Energy Ion Implantation

The inner surface modification process by plasma-based low-energy ion implantation（PBLEII）with an electron cyclotron resonance（ECR）microwave plasma source located at the central axis of a cylindrical tube is modeled to optimize the low-energy ion implantation parameters for industrial applications.In this paper,a magnetized plasma diffusion fluid model has been established to describe the plasma nonuniformity caused by plasma diffusion under an axial magnetic field during the pulse-off time of low pulsed negative bias.Using this plasma density distribution as the initial condition,a sheath collisional fluid model is built up to describe the sheath evolution and ion implantation during the pulse-on time.The plasma nonuniformity at the end of the pulse-off time is more apparent along the radial direction compared with that in the axial direction due to the geometry of the linear plasma source in the center and the difference between perpendicular and parallel plasma diffusion coefficients with respect to the magnetic field.The normalized nitrogen plasma densities on the inner and outer surfaces of the tube are observed to be about 0.39 and 0.24,respectively,of which the value is 1 at the central plasma source.After a 5μs pulse-on time,in the area less than 2 cm from the end of the tube,the nitrogen ion implantation energy decreases from 1.5 keV to 1.3 keV and the ion implantation angle increases from several degrees to more than 40°;both variations reduce the nitrogen ion implantation depth.However,the nitrogen ion implantation dose peaks of about 2×10^（10）-7×10^（10）ions/cm^2 in this area are 2-4 times higher than that of 1.18×10^（10）ions/cm^2 and 1.63×10^（10）ions/cm^2 on the inner and outer surfaces of the tube.The sufficient ion implantation dose ensures an acceptable modification effect near the end of the tube under the low energy and large angle conditions for nitrogen ion implantation,because the modification effect is mainly determined by the ion implantation dose,just as the mass transfer process in PBLEII is dominated by low-energy ion implantation and thermal diffusion.Therefore,a comparatively uniform surface modification by the low-energy nitrogen ion implantation is achieved along the cylindrical tube on both the inner and outer surfaces.

A NEW FEATURE-BASED MANNEQUIN MODELING METHOD

This paper presents a new feature-based mannequin modeling method, which is used in 3D computer aided garment design. Different from the traditional human modeling methods, a feature-based parametric design algorithm is involved in this method and mannequin posture animation is also implemented. They can greatly satisfy the requirements of the 3D computer aided garment design. At present, this mannequin modeling method has been implemented as a part of the computer aided 3D garment design system. Several mannequins for garment design have been manufactured by using this method and the rapid prototype technique.

CONSTRUCTING RECTANGULAR NURBS SURFACES IN TERMS OF THREE OF ITS FOUR BOUNDARY CURVES

in the paper, first, using the transinfinite interpolation strategy rectangular free formsurfaces with C0 and C1 cross boundary continuity are respectively generated by three of its fourboundary curves and corresponding cross derivatives. Then, their singularity is removed by anapproximation approach. Finally the surfaces are converted to the NURBS surfaces of degrees 5 × 6and 7×10 respectively. At the end of the paper, conclusions and examples are given.

Elucidating Dominant Factors Affecting Land Surface Hydrological Simulations of the Community Land Model over China

In order to compare the impacts of the choice of land surface model(LSM)parameterization schemes,meteorological forcing,and land surface parameters on land surface hydrological simulations,and explore to what extent the quality can be improved,a series of experiments with different LSMs,forcing datasets,and parameter datasets concerning soil texture and land cover were conducted.Six simulations are run for the Chinese mainland on 0.1°×0.1°grids from 1979 to 2008,and the simulated monthly soil moisture(SM),evapotranspiration(ET),and snow depth(SD)are then compared and assessed against observations.The results show that the meteorological forcing is the most important factor governing output.Beyond that,SM seems to be also very sensitive to soil texture information;SD is also very sensitive to snow parameterization scheme in the LSM.The Community Land Model version 4.5(CLM4.5),driven by newly developed observation-based regional meteorological forcing and land surface parameters(referred to as CMFD_CLM4.5_NEW),significantly improved the simulations in most cases over the Chinese mainland and its eight basins.It increased the correlation coefficient values from 0.46 to 0.54 for the SM modeling and from 0.54 to 0.67 for the SD simulations,and it decreased the root-mean-square error(RMSE)from 0.093 to 0.085 for the SM simulation and reduced the normalized RMSE from 1.277 to 0.201 for the SD simulations.This study indicates that the offline LSM simulation using a refined LSM driven by newly developed observation-based regional meteorological forcing and land surface parameters can better model reginal land surface hydrological processes.