A new four-dimensional chaotic system with first Lyapunov exponent of about 22,hyperbolic curve and circular paraboloid types of equilibria and its switching synchronization by an adaptive global integral sliding mode control

This paper presents a new four-dimensional（4 D） autonomous chaotic system which has first Lyapunov exponent of about 22 and is comparatively larger than many existing three-dimensional（3 D） and 4 D chaotic systems.The proposed system exhibits hyperbolic curve and circular paraboloid types of equilibria.The system has all zero eigenvalues for a particular case of an equilibrium point.The system has various dynamical behaviors like hyperchaotic,chaotic,periodic,and quasi-periodic.The system also exhibits coexistence of attractors.Dynamical behavior of the new system is validated using circuit implementation.Further an interesting switching synchronization phenomenon is proposed for the new chaotic system.An adaptive global integral sliding mode control is designed for the switching synchronization of the proposed system.In the switching synchronization,the synchronization is shown for the switching chaotic,stable,periodic,and hybrid synchronization behaviors.Performance of the controller designed in the paper is compared with an existing controller.

Vibration Control of a Composite Beam Using Self-sensing Semi-active Approach

Structural vibration control was an active research area for the past twenty years because of their potential applications in aerospace structures,civil structures,naval structures,etc.Semi-active vibration control methods based on piezoelectric actuators and synchronized switch damping on inductance（SSDI） techniques attract the attention of many researchers recently due to their advantages over passive and active methods.In the SSDI method,a switch shunt circuit is connected to the piezoelectric patch to shift the phase and amplify the magnitude of the voltage on the piezoelectric patch.The most important issue in SSDI method is to control the switching actions synchronously with the maximum vibration displacement or maximum strain.Hence,usually a displacement sensor is used to measure the vibration displacement or a collocated piezoelectric sensor is needed to measure the strain of the structure near the piezoelectric actuator.A self-sensing SSDI approach is proposed and applied to the vibration control of a composite beam,which avoids using a separate sensor.In the self-sensing technique,the same piezoelectric element functions as both a sensor and an actuator so that the total number of required piezoelectric elements can be reduced.One problem in the self-sensing actuator,which is the same as that in the traditional collocated piezoelectric sensors,is the noise generated in the sensor signal by the impact of voltage inversion,which may cause extra switching actions and deteriorate control performance.In order to prevent the shunt circuit from over-frequent on-and-off actions,a simple switch control algorithm is proposed.The results of control experiments show that the self-sensing SSDI approach combined with the improved switch control algorithm can effectively suppress over-frequent switching actions and gives good control performance by reducing the vibration amplitude by 45%,about 50% improvement from the traditional SSDI with a separate piezoelectric element and a classical switch.

A New Approach to Implement Synchronous Demultiplexers in High-Speed ISDN Switching Network

This paper proves that a synchronous demultiplexer has the same logic function as a synchronous multiplexer. A new approach is proposed to implement synchronous demultiplexers in high-speed ISDN switching networks. A synchronous demultiplexer is designed utilizing the same structure as a synchronous shuffle multiplexer. Both the theoretical analysis and experimental results show that for the same capacity, the new method is more tolerant of signal delay variation, so a very high-speed synchronous demultiplexer can be designed with the larger capacity required in large capacity synchronous switching networks.

Recent Development of Reluctance Machines with Different Winding Configurations,Excitation Methods,and Machine Structures

This paper reviews the performances of some newly developed reluctance machines with different winding configurations,excitation methods,stator and rotor structures,and slot/pole number combinations.Both the double layer conventional(DLC-),double layer mutually-coupled(DLMC),single layer conventional(SLC-),and single layer mutually-coupled(SLMC-),as well as fully-pitched(FP)winding configurations have been considered for both rectangular wave and sinewave excitations.Different conduction angles such as unipolar􀫚120°elec.,unipolar/bipolar􀫚180°elec.,bipolar􀫛240°elec.and bipolar􀫜360°elec.have been adopted and the most appropriate conduction angles have been obtained for the SRMs with different winding configurations.In addition,with appropriate conduction angles,the 12-slot/14-pole SRMs with modular stator structure is found to produce similar average torque,but lower torque ripple and iron loss when compared to non-modular 12-slot/8-pole SRMs.With sinewave excitation,the doubly salient synchronous reluctance machines with the DLMC winding can produce the highest average torque at high currents and achieve the highest peak efficiency as well.In order to compare with the conventional synchronous reluctance machines(SynRMs)having flux barriers inside the rotor,the appropriate rotor topologies to obtain the maximum average torque have been investigated for different winding configurations and slot/pole number combinations.Furthermore,some prototypes have been built with different winding configurations,stator structures,and slot/pole combinations to validate the predictions.

Adjust or Synchronize LM2586/88 Switching Frequency

INTRODUCTIONSwitching frequency is a very important parameter in switchingpower converters. As the switching frequency increases, the physicalsize of magnetic elements and other components in the circuit reducesignificantly. Switching frequency also plays a great role incontrol loop gain and compensation design. Switching frequency determinesthe maximum allowable bandwidth of the control loop.Switching frequency is also important parameter for EMI and noiseissues. The EMI spectrum is a direct function of the switching fre-

Mechanism of interconnected synchronized switch damping for vibration control of blades

The Synchronized Switch Damping(SSD)is regarded as a promising alternative to mitigate the vibration of thin-walled structures in aero-engines,especially for blades or bladed disks.The common manner is to shunt the switch circuit independently to a single piezoelectric structure.This paper is aimed at exploring a novel way of using the SSD,i.e.,the SSD is interconnected between two piezoelectric structures or substructures.The damping mechanism,performance,and effective range of the interconnected SSD are studied numerically and experimentally.First,based on a dual cantilever beam finite element model,the time domain and frequency domain modeling and solving methods of the interconnected SSD are deduced and validated.Then,the influence of the amplitude and phase relationship on the damping effect of the interconnected SSD is numerically studied and compared with the shunted SSD.A self-sensing SSD control board is developed,and experimental studies are carried out.The results show that the interconnected SSD establishes an additional energy channel between the corresponding piezoelectric structures.When the amplitudes of the two cantilever beams are different,the interconnected SSD balances the vibration level of each beam.When the amplitudes of the two cantilever beams are the same,if the appropriate interconnection manner is selected according to the phase,the resonance peak can be reduced by more than 30%.When the vibration is in-phase/out-of-phase,the damping generated by the interconnected SSD in a cross/parallel manner is even more significant than the shunted SSD.Furthermore,this novel connection scheme reduces the number of SSD circuits in half.Finally,for engineering applications,we implement the proposed damping technology to the finite element model of a typical dummy bladed disk.A piezoelectric damping ratio of 13.7%is achieved when the amount of piezo material is only 10%of blade mass.Compared with traditional friction dampers,the major advancements of the interconnected SSD are:(A)it can reduce the vibration level of blades without friction interface;(B)the space constraint is overcome,i.e.,the vibration energy is not necessarily dissipated independently in one sector or through physically adjacent blades,and instead,the dissipation and transfer of vibrational energy can be realized between any blade pair.If a specific gating circuit is adopted to adjust the interconnection manner of the SSD,vibration mitigation under variable working conditions with different engine orders will be expected;(C)designers do not need to worry about the annoying nonlinearities related to working conditions anymore.