In this paper, the research was focused on optimizing low-temperature heat recovery to adopt multi-effect distil- lation （MED） in desalination by pinch technology. And further analysis indicated that phase changes o...In this paper, the research was focused on optimizing low-temperature heat recovery to adopt multi-effect distil- lation （MED） in desalination by pinch technology. And further analysis indicated that phase changes occurred during the heat recovery process. In such case, the feed stream was divided into two streams： the liquid feed stream and the gaseous feed stream. Through calculation, the optimal ATmin was established at 26℃, and the total cost of heat exchange process was only $1.098× 106. By using the Problem Table Algorithm for pinch analysis, the temperature of the hot and the cold steams was 119℃ and 93 ℃, respectively. At a temperature higher than 119 ℃, all heat of the hot stream could not be cooled by the condenser, and the minimum heat load of utility （QH.min） was 440457.64 kW; and at a temperature below 93 ℃, all heat of the cold stream could not be provided by the heater, and the minimum cold load of utility （QC.min） was 1965993.85 kW. Finally, the synthesis of heat exchanger network was established through integrating two heat exchanger networks.展开更多
Lower temperature waste heats less than 373 K have strong potentials to supply additional energies because of their enormous quantities and ubiquity. Accordingly, reinforcement of power generations harvesting low temp...Lower temperature waste heats less than 373 K have strong potentials to supply additional energies because of their enormous quantities and ubiquity. Accordingly, reinforcement of power generations harvesting low temperature heats is one of the urgent tasks for the current generation in order to accomplish energy sustainability in the coming decades. In this study, a liquid turbine power generator driven by lower temperature heats below 373 K was proposed in the aim of expanding selectable options for harvesting low temperature waste heats less than 373 K. The proposing system was so simply that it was mainly composed of a liquid turbine, a liquid container with a biphasic medium of water and an underlying water-insoluble low-boiling-point medium in a liquid phase, a heating section for vaporization of the liquid and a cooling section for entropy discharge outside the system. Assumed power generating steps via the proposing liquid turbine power generator were as follows: step 1: the underlying low-boiling-point medium in a liquid phase was vaporized, step 2: the surfacing vapor bubbles of low-boiling-point medium accompanied the biphasic medium in their wakes, step 3: such high momentum flux by step 2 rotated the liquid turbine (i.e. power generation), step 4: the surfacing low-boiling-point medium vapor was gradually condensed into droplets, step 5: the low-boiling-point medium droplets were submerged to the underlying medium in a liquid phase. Experiments with a prototype liquid turbine power generator proved power generations in accordance with the assumed steps at a little higher than ordinary temperature. Increasing output voltage could be obtained with an increase in the cooling temperature among tested ranging from 294 to 296 K in contrast to normal thermal engines. Further improvements of the direct current voltage from the proposing liquid turbine power generator can be expected by means of far more vigorous multiphase flow induced by adding solid powders and theoretical optimizations of heat and mass transfers.展开更多
Effect of carbon, compound RE, quenching temperature, pre-strain and recovery temperature on shape memory effect (SME) of Fe-Mn-Si-Ni-C-RE shape memory alloy was studied by bent measurement, thermal cycle training, SE...Effect of carbon, compound RE, quenching temperature, pre-strain and recovery temperature on shape memory effect (SME) of Fe-Mn-Si-Ni-C-RE shape memory alloy was studied by bent measurement, thermal cycle training, SEM etc. It was shown that the grains of alloys addition with compound RE became finer and SME increased evidently. SME of the alloy was weakening gradually as carbon content increased under small strain (3%). But in the condition of large strain (more than 6%), SME of the alloy whose carbon content range from 0.1% to 0.12% showed small decreasing range, especially of alloy with the addition of compound RE. Results were also indicated that SME was improved by increasing quenching temperature (>1000℃). The amount of thermal induced martensite increased and the relative shape recovery ratio could be increased to more than 40% after 3-4 times thermal training. The relative shape recovery ratio decreased evidently depending on rising of pre-strain. Furthermore, because speed of martensite transition was extremely great under higher tempering temperature (more than 450℃, ε → γ transition completed in 10s meanwhile the relative shape recovery ratio of the alloy increased rapidly.展开更多
The rotating disk surface temperature rise due to windage heating effect by numerically modeling the turbulent flow within a rotor-stator cavity which is available with a peripheral shroud and imposed through airflow ...The rotating disk surface temperature rise due to windage heating effect by numerically modeling the turbulent flow within a rotor-stator cavity which is available with a peripheral shroud and imposed through airflow was dealt with.The windage heating may be defined as viscous friction heating caused by relative velocity differences across the boundary layers between the fluid and the rotating disk surface.The kinetic energy dissipation process could transform the rotating shaft power into thermal heating.Commercial finite volume based solver,ANSYS/CFX was employed to numerically simulate this physical process by using the shear stress transport(SST)turbulence model.CFD results include the rotating disk surface temperature axial distribution and tangential velocity distribution of the fluid domain.The velocity difference between the result obtained by particle image velocimetry(PIV)experiments and CFD simulation are within 5%.The adiabatic disk temperature rise can be calculated by the tangential velocity of disk and fluid in large gap ratio and turbulent parameter.CFD temperature distribution results and those estimated via velocity differences are within 10%.展开更多
基金the National Nature Science Foundation (Grant No. 51178463)
文摘In this paper, the research was focused on optimizing low-temperature heat recovery to adopt multi-effect distil- lation （MED） in desalination by pinch technology. And further analysis indicated that phase changes occurred during the heat recovery process. In such case, the feed stream was divided into two streams： the liquid feed stream and the gaseous feed stream. Through calculation, the optimal ATmin was established at 26℃, and the total cost of heat exchange process was only $1.098× 106. By using the Problem Table Algorithm for pinch analysis, the temperature of the hot and the cold steams was 119℃ and 93 ℃, respectively. At a temperature higher than 119 ℃, all heat of the hot stream could not be cooled by the condenser, and the minimum heat load of utility （QH.min） was 440457.64 kW; and at a temperature below 93 ℃, all heat of the cold stream could not be provided by the heater, and the minimum cold load of utility （QC.min） was 1965993.85 kW. Finally, the synthesis of heat exchanger network was established through integrating two heat exchanger networks.
文摘Lower temperature waste heats less than 373 K have strong potentials to supply additional energies because of their enormous quantities and ubiquity. Accordingly, reinforcement of power generations harvesting low temperature heats is one of the urgent tasks for the current generation in order to accomplish energy sustainability in the coming decades. In this study, a liquid turbine power generator driven by lower temperature heats below 373 K was proposed in the aim of expanding selectable options for harvesting low temperature waste heats less than 373 K. The proposing system was so simply that it was mainly composed of a liquid turbine, a liquid container with a biphasic medium of water and an underlying water-insoluble low-boiling-point medium in a liquid phase, a heating section for vaporization of the liquid and a cooling section for entropy discharge outside the system. Assumed power generating steps via the proposing liquid turbine power generator were as follows: step 1: the underlying low-boiling-point medium in a liquid phase was vaporized, step 2: the surfacing vapor bubbles of low-boiling-point medium accompanied the biphasic medium in their wakes, step 3: such high momentum flux by step 2 rotated the liquid turbine (i.e. power generation), step 4: the surfacing low-boiling-point medium vapor was gradually condensed into droplets, step 5: the low-boiling-point medium droplets were submerged to the underlying medium in a liquid phase. Experiments with a prototype liquid turbine power generator proved power generations in accordance with the assumed steps at a little higher than ordinary temperature. Increasing output voltage could be obtained with an increase in the cooling temperature among tested ranging from 294 to 296 K in contrast to normal thermal engines. Further improvements of the direct current voltage from the proposing liquid turbine power generator can be expected by means of far more vigorous multiphase flow induced by adding solid powders and theoretical optimizations of heat and mass transfers.
文摘Effect of carbon, compound RE, quenching temperature, pre-strain and recovery temperature on shape memory effect (SME) of Fe-Mn-Si-Ni-C-RE shape memory alloy was studied by bent measurement, thermal cycle training, SEM etc. It was shown that the grains of alloys addition with compound RE became finer and SME increased evidently. SME of the alloy was weakening gradually as carbon content increased under small strain (3%). But in the condition of large strain (more than 6%), SME of the alloy whose carbon content range from 0.1% to 0.12% showed small decreasing range, especially of alloy with the addition of compound RE. Results were also indicated that SME was improved by increasing quenching temperature (>1000℃). The amount of thermal induced martensite increased and the relative shape recovery ratio could be increased to more than 40% after 3-4 times thermal training. The relative shape recovery ratio decreased evidently depending on rising of pre-strain. Furthermore, because speed of martensite transition was extremely great under higher tempering temperature (more than 450℃, ε → γ transition completed in 10s meanwhile the relative shape recovery ratio of the alloy increased rapidly.
文摘The rotating disk surface temperature rise due to windage heating effect by numerically modeling the turbulent flow within a rotor-stator cavity which is available with a peripheral shroud and imposed through airflow was dealt with.The windage heating may be defined as viscous friction heating caused by relative velocity differences across the boundary layers between the fluid and the rotating disk surface.The kinetic energy dissipation process could transform the rotating shaft power into thermal heating.Commercial finite volume based solver,ANSYS/CFX was employed to numerically simulate this physical process by using the shear stress transport(SST)turbulence model.CFD results include the rotating disk surface temperature axial distribution and tangential velocity distribution of the fluid domain.The velocity difference between the result obtained by particle image velocimetry(PIV)experiments and CFD simulation are within 5%.The adiabatic disk temperature rise can be calculated by the tangential velocity of disk and fluid in large gap ratio and turbulent parameter.CFD temperature distribution results and those estimated via velocity differences are within 10%.
