Preparation and performance evaluation of the slickwater using novel polymeric drag reducing agent with high temperature and shear resistance ability

Slickwater fracturing fluids are widely used in the development of unconventional oil and gas resources due to the advantages of low cost,low formation damage and high drag reduction performance.However,their performance is severely affected at high temperatures.Drag reducing agent is the key to determine the drag reducing performance of slickwater.In this work,in order to further improve the temperature resistance of slickwater,a temperature-resistant polymeric drag reducing agent(PDRA)was synthesized and used as the basis for preparing the temperature-resistant slickwater.The slickwater system was prepared with the compositions of 0.2 wt%PDRA,0.05 wt%drainage aid nonylphenol polyoxyethylene ether phosphate(NPEP)and 0.5 wt%anti-expansion agent polyepichlorohydrindimethylamine(PDM).The drag reduction ability,rheology properties,temperature and shear resistance ability,and core damage property of slickwater were systematically studied and evaluated.In contrast to on-site drag reducing agent(DRA)and HPAM,the temperature-resistant slickwater demonstrates enhanced drag reduction efficacy at 90℃,exhibiting superior temperature and shear resistance ability.Notably,the drag reduction retention rate for the slickwater achieved an impressive 90.52%after a 30-min shearing period.Additionally,the core damage is only 5.53%.We expect that this study can broaden the application of slickwater in high-temperature reservoirs and provide a theoretical basis for field applications.

Improving corrosion resistance of additively manufactured WE43 magnesium alloy by high temperature oxidation for biodegradable applications

Laser powder bed fusion(L-PBF)has been employed to additively manufacture WE43 magnesium(Mg)alloy biodegradable implants,but WE43 L-PBF samples exhibit excessively rapid corrosion.In this work,dense WE43 L-PBF samples were built with the relativity density reaching 99.9%.High temperature oxidation was performed on the L-PBF samples in circulating air via various heating temperatures and holding durations.The oxidation and diffusion at the elevated temperature generated a gradient structure composed of an oxide layer at the surface,a transition layer in the middle and the matrix.The oxide layer consisted of rare earth(RE)oxides,and became dense and thick with increasing the holding duration.The matrix was composed ofα-Mg,RE oxides and Mg_(24)RE_(5) precipitates.The precipitates almost disappeared in the transition layer.Enhanced passivation effect was observed in the samples treated by a suitable high temperature oxidation.The original L-PBF samples lost 40%weight after 3-day immersion in Hank’s solution,and broke into fragments after 7-day immersion.The casted and solution treated samples lost roughly half of the weight after 28-day immersion.The high temperature oxidation samples,which were heated at 525℃ for 8 h,kept the structural integrity,and lost only 6.88%weight after 28-day immersion.The substantially improved corrosion resistance was contributed to the gradient structure at the surface.On one hand,the outmost dense layer of RE oxides isolated the corrosive medium;on the other hand,the transition layer considerably inhibited the corrosion owing to the lack of precipitates.Overall,high temperature oxidation provides an efficient,economic and safe approach to inhibit the corrosion of WE43 L-PBF samples,and has promising prospects for future clinical applications.

Evaluation of Cold Resistance and Semi-lethal Low Temperature(LT_(50))of Nine Pear Cultivars

[Objectives]To evaluate the cold resistance and semi-lethal temperature of pear cultivars,and provide a theoretical basis for the regional extension and breeding of cold-resistant pear cultivars.[Methods]Nine pear cultivars were used to study the changes in relative conductivity and cell injury rate of pear branches under low temperature stress,and the semi-lethal temperature(LT_(50))of pear branches was analyzed by fitting Logistic equation.[Results]The relative conductivity and cell injury rate of pear branches took on the trend of slow increase,rapid increase,and slow increase the decrease of treatment temperature.The LC_(50) of the nine pear cultivars were as follows:Nanguo pear-33.9℃,Wanyu-32.3℃,Red D Anjou-31.8℃,Jinfeng-31.3℃,Wujiuxiang-29.2℃,20 th Century Pear-29.1℃,Hanxiang-35.1℃,Yuluxiang-27.9℃ and Korla Fragrant Pear-29.2℃.[Conclusions]The semi-lethal temperature could reflect the cold resistance of pear trees,and Wanxiang had better cold resistance.The evaluation of cold resistance and semi-lethal temperature of pear cultivars can provide theoretical basis for regional extension and breeding of cold-resistant pear cultivars.

Screening of Wheat Cultivars for High Temperature Resistance to Stripe Rust from Wheat Resources in Huanghuai Growth Area

[Objective] The study aimed to screen wheat cultivars with high temperature resistance to stripe rust from the wheat resources in Huanghuai growth area. [Method] Seedlings of 165 wheat cultivars from Huanghuai growth area were identified by wheat stripe rust under high temperature; then the wheat cultivars showing stripe rust at seedling stage were further used to identify the same resistance in field. [Results] 13 cultivars were proved to be stripe rust resistant under high temperature, and the expression stages of stripe rust in the 13 cultivars were revealed. The field identification results confirmed the identification results at seedling stage via inoculation of mixed stripe rust of physiological races. The stripe resistances of wheat cultivars were also proved to be non-race-specific. [Conclusion] Wheat resources in Huanghuai growth area are abundant in wheat cultivars with high temperature resistance to stripe rust.

High temperature oxidation resistance and microstructure change of aluminized coating on copper substrate

The outermost coating with single phase Ni2Al3 was obtained on copper surface by electrodepositing nickel followed by slurry pack aluminizing at 800 °C for 12 h. The oxidation resistance and microstructure of the coating oxidized in ambient air at 1000 °C for 25-250 h were investigated using SEM, X-ray diffraction and optical microscope methods. The results show that the copper with single phase Ni2Al3 coating possesses the best high temperature oxidation resistance, and the mass gain of the coating is 1/15 that of pure copper and 1/2 that of nickel coating, respectively. The specimen surface after being oxidized for 25 h still comprises Ni2Al3 phase. However, when the time of oxidizing treatment increases to 50 h, the Ni Al phase is formed. It is also found that the Ni2Al3 phase completely turns into Ni Al phase after oxidizing treatment for 100 h and above. The Ni Al coating shows excellent high temperature oxidation resistance when oxidation time is 250 h.

Microstructure and high temperature oxidation resistance of Si-Y co-deposition coatings prepared on TiAl alloy by pack cementation process

In order to improve the high temperature oxidation resistance of TiAl alloy, Y modified silicide coatings were prepared by pack cementation process at 1030, 1080 and 1130 °C, respectively, for 5 h. The microstructures, phase constitutions and oxidation behavior of these coatings were studied. The results show that the coating prepared by co-depositing Si?Y at 1080 °C for 5 h has a multiple layer structure: a superficial zone consisting of Al-rich (Ti,Nb)5Si4 and (Ti,Nb)5Si3, an out layer consisting of (Ti,Nb)Si2, a middle layer consisting of (Ti,Nb)5Si4 and (Ti,Nb)5Si3, and aγ-TiAl inner layer. Co-deposition temperature imposes strong influences on the coating structure. The coating prepared by Si?Y co-depositing at 1080 °C for 5 h shows relatively good oxidation resistance at 1000 °C in air, and the oxidation rate constant of the coating is about two orders of magnitude lower than that of the bare TiAl alloy.

Effects of slurry pack cementation temperature on microstructure and wear resistance of Ti-Al co-deposited coating on copper plated nickel layer

In order to improve the wear resistance properties of copper substrate, a layer of electroplated nickel was firstly deposited on copper substrate, subsequently these electroplated specimens were treated by slurry pack cementation process with a slurry pack cementation mixture composed of TiO2 as titanizing source, pure Al powder as aluminzing source and also a reducer for titanizing, an activator of NH4Cl and albumen （egg white） as cohesive agent. The Ti-Al coating was fabricated on the surface of electro-deposited nickel layer on copper matrix followed by the slurry pack cementation process. The effects of slurry pack cementation temperature on the microstructures and wear resistance of Ti-Al coating were studied. The results show that the microstructure of the coating changed from NiAl＋Ni3（Ti,Al） to NiAl ＋Ni3（Ti,Al）＋Ni4Ti3 to Ni4Ti3＋NiAl, and to NiAl＋Ni3（Ti,Al）＋NiTi with slurry pack cementation temperature ranging from 800 ℃ to 950 ℃ in 12 h. The friction coefficient of Ti-Al coating decreased and the hardness increased with increasing the slurry pack cementation temperature. The minimum friction coefficient was 1/3 and the minimum hardness was 5 times larger than that of pure copper.

Development and performance evaluation of high temperature resistant strong adsorption rigid blocking agent

As drilling wells continue to move into deep ultra-deep layers,the requirements for temperature resistance of drilling fluid treatments are getting higher and higher.Among them,blocking agent,as one of the key treatment agents,has also become a hot spot of research.In this study,a high temperature resistant strong adsorption rigid blocking agent(QW-1)was prepared using KH570 modified silica,acrylamide(AM)and allyltrimethylammonium chloride(TMAAC).QW-1 has good thermal stability,average particle size of 1.46μm,water contact angle of 10.5.,has a strong hydrophilicity,can be well dispersed in water.The experimental results showed that when 2 wt%QW-1 was added to recipe A(4 wt%bentonite slurry+0.5 wt%DSP-1(filtration loss depressant)),the API filtration loss decreased from 7.8to 6.4 m L.After aging at 240.C,the API loss of filtration was reduced from 21 to 14 m L,which has certain performance of high temperature loss of filtration.At the same time,it is effective in sealing 80-100mesh and 100-120 mesh sand beds as well as 3 and 5μm ceramic sand discs.Under the same conditions,the blocking performance was superior to silica(5μm)and calcium carbonate(2.6μm).In addition,the mechanism of action of QW-1 was further investigated.The results show that QW-1 with amide and quaternary ammonium groups on the molecular chain can be adsorbed onto the surface of clay particles through hydrogen bonding and electrostatic interaction to form a dense blocking layer,thus preventing further intrusion of drilling fluid into the formation.

Shear resistance characteristics and influencing factors of root-soil composite on an alpine metal mine dump slope with different recovery periods

Artificial vegetation restoration is the main measure for vegetation restoration and soil and water conservation in alpine mine dumps on the Qinghai-Tibet Plateau,China.However,there are few reports on the dynamic changes and the influencing factors of the soil reinforcement effect of plant species after artificial vegetation restoration under different recovery periods.We selected dump areas of the Delni Copper Mine in Qinghai Province,China to study the relationship between the shear strength and the peak displacement of the root-soil composite on the slope during the recovery period,and the influence of the root traits and soil physical properties on the shear resistance characteristics of the root-soil composite via in situ direct shear tests.The results indicate that the shear strength and peak displacement of the rooted soil initially decreased and then increased with the increase of the recovery period.The shear strength of the rooted soil and the recovery period exhibited a quadratic function relationship.There is no significant function relationship between the peak displacement and the recovery period.Significant positive correlations(P<0.05)exists between the shear strength of the root-soil composite and the root biomass density,root volume density,and root area ratio,and they show significant linear correlations(P<0.05).There are no significant correlations(P>0.05)between the shear strength of the root-soil composite and the root length density,and the root volume ratio of the coarse roots to the fine roots.A significant negative linear correlation(P<0.05)exists between the peak displacement of the rooted soil and the coarse-grain content,but no significant correlations(P>0.05)with the root traits,other soil physical property indices(the moisture content and dry density of the soil),and slope gradient.The coarse-grain content is the main factor controlling the peak displacement of the rooted soil.

Shear Resistance of Siltous Sands Improved with Bridelia Tannins

The ruin of several civil engineering works occurs due to shear rupture of the ground. When the stress is greater than the shear resistance, the internal friction angle and the cohesion of the soil loosen and rupture occurs. Cement and lime are often used to stabilize soils and improve soil strength. The costs and environmental problems of these technologies raise concerns and challenge researchers to innovate with clean, inexpensive materials, accessible to the most disadvantaged social classes. The question that this study seeks to answer is whether the binders derived from plant tannins, which also stabilize soils, improve the shear resistance of these soils. To do this, we determined for silty sand the shear parameters, notably the cohesion and the angle of internal friction in the non-stabilized state and when they are stabilized with the powder of the bark of the Bridelia under different water states. The results show that the addition of Bridelia powder to silty sand increases the cohesion of the soil by nearly 70.71% and the friction angle by 4.31%. But in unfavourable water conditions, the cohesion and internal friction angle of the silty sand material improved with Bridelia bark powder drops drastically by nearly 81.56%. but does not dissolve completely as for the same material. When it is not stabilized. This information is an invaluable contribution in the search for solutions to increase the durability of earthen constructions by improving the water-repellent properties of soils.

Numerical simulation on temperature field for resistance spot welding of non-equal thickness stainless steel

An axisymmetric finite element model is developed to simulate the temperature field of resistant spot welding according to the process characters of nugget formation of non equal stainless steel sheets. A simulation method of the interaction of electrical and thermal factors is presented. The spot welding process of nugget formation is simulated using hard and soft welding technique norms. The heating characters of soft and hard norms determine the differences in the process of nugget formation and determine the finally shape and offset of nugget. Experimental verification shows that the model prediction agrees well with the practical.

Effect of contact thermal resistance on temperature distributions of concrete-filled steel tubes in fire

To predicate the temperature distribution of concrete-filled steel tubes(CFSTs) being exposure to fire,a finite element analysis model was developed using a finite element package,ANSYS.A suggested value of contact thermal resistance was therefore proposed with the supporting of massive numbers of collected test data.Parametric analysis was conducted subsequently towards the cross-sectional temperature distribution of CFST columns in four-side fire,in which the exposure time,width of the cross section,steel ratio were taken into account with considering contact thermal resistance.It was found that contact thermal resistance has little effect on the overall temperature regulation with the exposure time,the width of cross-section or the change of steel ratio.However,great temperature dropping at the concrete adjacent to the contact interface,and gentle temperature increase at steel tube,exist if considering contact thermal resistance.The results of the study are expected to provide theoretical basis for the fire resistance behavior and design of the CFST columns being exposure to fire.

High Temperature Modifies Resistance Performances of Rice Varieties to Brown Planthopper,Nilaparvata lugens(Stl)

To investigate the effect of temperature on the resistance characteristics of dce varieties with different resistance genes to brown planthopper （BPH）, Nilaparvata lugens （Stal）, the resistances of IR26 （Bphl） and IR36 （bph2） to BPH population in Hangzhou, China were monitored in greenhouse during September in 2007 and 2008 by using the standard seedling screening techniques （SSST） developed by the International Rice Research Institute （IRRI）. Furthermore, the changes in resistance of IR26 and IR36 to BPH, soluble sugar and oxalic acid contents in 25-day-old rice plants of susceptible variety TN1 and resistant varieties IR26 and IR36 were detected at five temperatures （22℃, 25℃, 28℃, 31℃ and 34℃）. IR26 completely lost resistance both in greenhouse and at the five tested temperatures. IR36 still had moderate resistance at natural temperature, but its resistance decreased gradually when the temperature increased from 25℃ to 34℃, and fully lost its resistance at 31℃ and 34℃. The highest durable resistance of IR26 and IR36 were recorded at 25℃. The soluble sugar content in plants of the three tested rice varieties increased with temperature increase, and the oxalic acid content increased with the temperature increase at first, maximized at 25℃, and then declined. Two-way ANOVA indicated significant effects of temperature and rice variety on contents of soluble sugar and oxalic acid in rice plants

Thin Film Chip Resistors with High Resistance and Low Temperature Coefficient of Resistance

High resistance thin film chip resistors(0603 type) were studied,and the specifications are as follows:1 k? with tolerance about ±0.1% after laser trimming and temperature coefficient of resistance(TCR) less than ±15×10-6/℃.Cr-Si-Ta-Al films were prepared with Ar flow rate and sputtering power fixed at 20 standard-state cubic centimeter per minute(sccm) and 100 W,respectively.The experiment shows that the electrical properties of Cr-SiTa-Al deposition films can meet the specification requirements of 0603 ty...

Experimental investigation of high temperature thermal contact resistance with interface material

Thermal contact resistance plays a very important role in heat transfer efficiency and thermomechanical coupling response between two materials,and a common method to reduce the thermal contact resistance is to fill a soft interface material between these two materials.A testing system of high temperature thermal contact resistance based on INSTRON 8874 is established in the present paper,which can achieve 600 C at the interface.Based on this system,the thermal contact resistance between superalloy GH600 material and three-dimensional braid C/C composite material is experimentally investigated,under different interface pressures,interface roughnesses and temperatures,respectively.At the same time,the mechanism of reducing the thermal contact resistance with carbon fiber sheet as interface material is experimentally investigated.Results show that the present testing system is feasible in the experimental research of high temperature thermal contact resistance.

Mechanical properties and wear resistance of ultrafine bainitic steel under low austempering temperature

The mechanical properties and wear resistance of the ultrafine bainitic steel austempered at various temperatures were investigated.Scanning electron microscopy(SEM)and X-ray diffraction were used to analyze the microstructure.The worn surfaces were observed via laser scanning confocal microscopy and SEM.Results indicated that,under low austempering temperatures,the mechanical properties differed,and the wear resistance remained basically unchanged.The tensile strength of the samples was above 1800 MPa,but only one sample austempered at 230°C had an elongation of more than 10%.The weight loss of samples was approximately linear with the cycles of wear and nonlinear with the loads.The samples showed little difference in wear resistance at different isothermal temperatures,whereas the thickness of their deformed layers varied greatly.The results are related to the initial hardness of the sample and the stability of the retained austenite.Meanwhile,the experimental results showed that the effect of austempering temperature on the wear resistance of ultrafine bainitic steel can be neglected under low applied loads and low austempering temperature.

Effect of platform temperature on microstructure and corrosion resistance of selective laser melted Al-Mg-Sc alloy plate

The Al-3.40Mg-1.08Sc alloy plates were manufactured by selective laser melting(SLM) at platform temperatures of 35 ℃ and 200 ℃, respectively, and the corrosion performance of them was studied along height direction. The results show that the corrosion resistance of the alloy plate built at platform temperature of 35 ℃ along height direction is basically the same due to a uniform microstructure;While the corrosion resistance of the alloy plate built at platform temperature of 200 ℃ along height direction is different. The evolution of microstructure and the distribution of secondary phases are investigated, and the results show that the Cu-rich phases in alloy play a key role on corrosion performance. At higher platform temperature, the cooling rate is relative slow and a certain degree of in situ ageing leads to the significantly different distribution of Cu-rich phases along grain boundary. Specimens built at the platform temperature of 200 ℃ are inclined to locate at the crossed grain boundary, rather than continuous segregation of Cu-rich phases along grain boundary that is built at platform temperature of 35 ℃. Therefore, the corrosion resistance of Al-3.40Mg-1.08Sc alloy plate manufactured at platform temperature of 200 ℃ is higher, and presents a gradually decreasing trend along height direction.

High Temperature Effects on Yeast-like Endosymbiotes and Pesticide Resistance of the Small Brown Planthopper, Laodelphax striatellus

The newly-hatched nymphs of the small brown planthopper (SBPH), Laodelphax striatellus, including field and sensitive populations, were subjected to the high-temperature (35°C) treatment. The number of yeast-like endosymbiotes in SBPH reduced by 23.47%–34.23%, 57.86%–61.51% and 88.96%–90.71% after the high-temperature treatment for 1 d, 2 d, and 3 d, respectively. However, the size of yeast-like endosymbiotes was not obviously affected. Resistance of SBPH to three insecticides (imidacloprid, chlorpyrifos and fipronil) decreased with the increase of treatment time.

The Method for Measuring the Loop Resistance and the Temperature Rise Calculation of GIS Conductor Pole

This paper studies the method for measuring the loop resistance of GIS conductor pole based on the super capacitor producing impulse current up to several thousand amperes. This method overcomes the limitations of conventional diagnostic method. Typical GIS conductor poles are chosen. Based on FEA and lab tests, the effect of different forms of current and contact condition, relationship between the temperature of contact and the loop resistance is researched. In full- scale testing under realistic operating conditions on the new 220 kV GIS using prototype instrumentation a very good sensitivity in an early stage was obtained.

High-temperature Resistance Performance of An Inorganic Adhesive for Concrete Structures Strengthened with CFRP Sheets

Organic epoxy matrices have been widely used in the FRP reinforcing technique, but they have serious disadvantages of poor high-temperature resistance. An inorganic adhesive is invented to replace the organic adhesive. For the inorganic adhesive at normal temperature and different high temperatures, the microstructure and phase composition are investigated by means of X-ray diffraction （XRD） and SEM respectively. Results show that inorganic adhesive can resist at least 600 ℃ high temperature. Fire-resistance performance of inorganic adhesive can meet the requirements of fiber reinforced polymer （FRP） strengthened RC structures.