Instrumented oscillographic study on impact toughness of an axle steel DZ2 with different tempering temperatures

Compared with the conventional Charpy impact test method,the oscillographic impact test can help in the behavioral analysis of materials during the fracture process.In this study,the trade-off relationship between the strength and toughness of a DZ2 axle steel at various tempering temperatures and the cause of the improvement in impact toughness was evaluated.The tempering process dramatically influenced carbide precipitation behavior,which resulted in different aspect ratios of carbides.Impact toughness improved along with the rise in tempering temperature mainly due to the increase in energy required in impact crack propagation.The characteristics of the impact crack propagation process were studied through a comprehensive analysis of stress distribution,oscilloscopic impact statistics,fracture morphology,and carbide morphology.The poor impact toughness of low-tempering-temperature specimens was attributed to the increased number of stress concentration points caused by carbide morphology in the small plastic zone during the propagation process,which resulted in a mixed distribution of brittle and ductile fractures on the fracture surface.

Effect of Valence Electron Structure on Temper Process and Hardness of the Supersaturated Carburized Layer

By measuring the hardness of carburized layer of a new type supersaturated carburizing steel （35Cr3SiMnMoV） at different temper temperature for 2 h, the relationship curve between the carburized layer hardness and the temper temperature is established. The result indicates that the hardness goes down firstly, then up and down, just like a wave consistent with the temperature increase. A secondary hardening peak appears at 570 ℃ or so. Based on Empirical Election Theory （EET） of Solids and Molecules, the valence electron structures （VESs） containing α-Fe-C, α-Fe-C-Me segregation structure units and carbide are calculated. The laws of temper process and hardness change with the temper temperature are explained, and the fact that reconstruction of θ-Fe3C is prior to that of special carbide at high tempering is analyzed with the phase structure formation factor, S, being taken into consideration. Therefore, the laws of temper process and hardness change of supersaturated carburized layer at different temper temperature can be traced back to valence electron structure （VES） level of alloy phase.

Numerical simulation research of dimension variation in heavy plate during quenching and tempering process

The dimension variation of B610E steel during the quenching and tempering process was simulated by ABAQUS,the coefficient of heat transfer during quenching was verified by the buried thermocouple test and the trend of the dimension variation during the quenching process was also calculated by ABAQUS. It was shown by the comparison of simulated results and industrially measured results that only the simulation of thickness and width variation was accurate, while length variation needed further simulation. Besides, the dimension variation trend was identical with the measured results.

Seasonal evolution of the englacial and subglacial drainage systems of a temperate glacier revealed by hydrological analysis

Englacial and subglacial drainage systems of temperate glaciers have a strong influence on glacier dynamics, glacier-induced floods, glacier-weathering processes, and runoff from glacierized drainage basins. Proglacial discharge is partly controlled by the geometry of the glacial drainage network and by the process of producing meltwater. The glacial-drainage system of some alpine glaciers has been characterized using a model based on proglacial discharge analysis. In this paper, we apply cross-correlation analysis to hourly hydro-climatic data collected from China＇s Hailuogou Glacier, a typical temperate glacier in Mt. Gongga, to study the seasonal status changes of the englacial and subglacial drainage systems by discharge-temperature （Q-T） time lag analy-sis. During early ablation season （April-May） of 2003, 2004 and 2005, the change of englacial and subglacial drainage system usually leads several outburst flood events, which are also substantiated by observing the leakage of supraglacial pond and cre-vasses pond water during field works in April, 2008. At the end of ablation season （October-December）, the glacial-drainage net-works become less hydro-efficient. Those events are evidenced by hourly hydro-process near the terminus of Hailuogou Glacier, and the analysis of Q-T time lags also can be a good indicator of those changes. However, more detailed observations or experi-ments, e.g. dye-tracing experiment and recording borehole water level variations, are necessary to describe the evolutionary status and processes of englacial and subglacial drainage systems evolution during ablation season.

Tempering Process to Improve Hardness Uniformity of Plastic Mould Steel

A new design of copper-bearing non-quenched plastic mold steel is presented and explained. Two kinds of microstrueture can be obtained from this new type copper-bearing steel via cooling with different cooling rates, bain- ite and a mixed microstructure consisting of ferrite and bainite. It is found that, after proper tempering process, the hardness will be increased. Moreover, the hardness difference between different microstructures will be reduced. For further investigation, the samples tempered at different temperatures were examined by XRD and 3PAP （three di- mensional atom probe） analysis. Results show that the improvement is contributed mainly by the precipitation of Cu phase and transformation of residual austenite.

High Temperature Rapid Tempering Process of SS400 Steel With Thermomechanical Simulation Tester

The effect of refined precipitations and dispersed phases on the toughness of SS400 steel was investigated by rapid tempering with thermomechanical simulation tester, and the electromagnetic induction rapid tempering process was simulated. The conventional tempering and rapid tempering process were proceeded respectively, and both samples were quenched in 10~ of agitated iced brine. The tempering temperatures were designed as 560, 620 and 680℃, respectively. Rapid tempering specimens were heated at a heating rate of 20 ℃/s, and all samples of these three tempering temperatures were maintained 30, 40 and 50 s with the Gleeble1500-D tester, respectively. The impact test at --40 ℃ were carried out on a Charpy impact machine （CBD-300） with a maximum measurement range of 300 J and the microstructures were analyzed in detail using optical microscope （OM） and scanning electron microscope （SEM）. The experiment results show that the upper bainite, martensite and small amount of austenite were obtained in the rapidly quenched samples. In comparison to the conventional process, the matrix microstructure was changed from the larger size and bulk ferrite to the refined banding structure, and the cementites were obviously refined and precipitated inside the grains and along the grain boundaries. The cryogenic impact test implies that the maximum values of impact toughness with holding time of 30 or 50 s are achieved at tempering temperature of 620℃. Furthermore, a favorite value of impact toughness with holding time of 40 s is available.