Atomistic evaluation of tension–compression asymmetry in nanoscale body-centered-cubic AlCrFeCoNi high-entropy alloy

The tension and compression of face-centered-cubic high-entropy alloy(HEA) nanowires are significantly asymmetric, but the tension–compression asymmetry in nanoscale body-centered-cubic(BCC) HEAs is still unclear. In this study,the tension–compression asymmetry of the BCC Al Cr Fe Co Ni HEA nanowire is investigated using molecular dynamics simulations. The results show a significant asymmetry in both the yield and flow stresses, with BCC HEA nanowire stronger under compression than under tension. The strength asymmetry originates from the completely different deformation mechanisms in tension and compression. In compression, atomic amorphization dominates plastic deformation and contributes to the strengthening, while in tension, deformation twinning prevails and weakens the HEA nanowire.The tension–compression asymmetry exhibits a clear trend of increasing with the increasing nanowire cross-sectional edge length and decreasing temperature. In particular, the compressive strengths along the [001] and [111] crystallographic orientations are stronger than the tensile counterparts, while the [110] crystallographic orientation shows the exactly opposite trend. The dependences of tension–compression asymmetry on the cross-sectional edge length, crystallographic orientation,and temperature are explained in terms of the deformation behavior of HEA nanowire as well as its variations caused by the change in these influential factors. These findings may deepen our understanding of the tension–compression asymmetry of the BCC HEA nanowires.

A crystal plasticity based approach to establish role of grain size and crystallographic texture in the Tension–Compression yield asymmetry and strain hardening behavior of a Magnesium–Silver–Rare Earth alloy

Existence of tension–compression yield asymmetry is a serious limitation to the load bearing capablities of Magnesium alloys in a number of light weight structural applications.The present work is aimed at nullifying the tension to compression asymmetry problem and strain hardening anomalies in a Magnesium–Silver–Rare Earth alloy by engineering different levels of microstructural conditions via friction stir processing and post process annealing.The existence and extent of yield asymmetry ratio in the range of microstructural conditions was experimentally obtained through quasistatic tensile and compression tests.The yield asymmetry problem was profoundly present in specimens of coarse grained microstructures when compared to their fine grained and ultra fine grained counterparts.The impact of the microstructure and associated mechanisms of plasticity on the macroscopic strain hardening behavior was established by Kock–Mecking’s analysis.Crystal plasticity simulations using Viscoplastic Self Consistency approach revealed the consequential role of extension twinning mechanism for the existence of yield asymmetry and anomalies in strain hardening behavior.This was especially dominant with coarsening of grain size.Electron Microscopy and characterization were conducted thoroughly in partially deformed specimens to confirm the predictions of the above simulations.The role of crystallographic texture for inducing the polarity to Tension–Compression yield asymmetry was corroborated.A critical grain size in Magnesium–Silver–Rare earth alloy was hereby established which could nullify influences of extension twinning in yield asymmetry ratio.

Reducing the yield asymmetry in Mg-5Li-3Al-2Zn alloy by hot-extrusion and multi-pass rolling

Reducing the yield asymmetry is very important concern for wrought Mg-Li alloys.In this study,Mg-5Li-3Al-2 Zn(LAZ532)alloy was successfully produced by hot-extrusion followed by multi-pass rolling at 573 K.Microstructure evolution,mechanical properties and yield asymmetry reducing of LAZ532 alloys at different rolling passes were studied.By observing microstructure using transmission electron microscopy showed that a small amount of ultra-fine Al Mg_(4)Zn_(11)and nano Li_(3)Al_(2) phases existed in the alloy.With the increasing of rolling passes,the grains of the alloys were obviously refined,and comprehensive mechanical properties were dramatically improved.Meanwhile,it also showed an excellent tension and compression yield symmetry(TYS/CYS was about 1).The results showed that the combined action of the weak{0001}basal lamellar texture,grain refinement and addition of Li element could effectively improve the yield symmetry.Furthermore,based on theoretical analysis,the yield strength in the alloys mainly depended on the strengthening contributions of LAGBs and HAGBs,and strengthening effect of HAGBs most(~50%)to the yield strength improvement.

Intrinsic Strength Asymmetry Between Tension and Compression of Perfect Face-Centered-Cubic Crystals

The strength asymmetry between tension and compression is a typical case of mechanical response of materials.Here we achieve the intrinsic strength asymmetry of six face-centered-cubic perfect crystals（Cu,Au,Ni,Pt,Al and Ir）through calculating the ideal tensile and compressive strength with considering the normal stress effect and the competition between different crystallographic planes.The results show that both the intrinsic factors（the ideal shear strength and cleavage strength of low-index planes）and the orientation could affect the strength asymmetry,which may provide insights into understanding the strength of ultra-strong materials.

Annealing hardening and deformation behavior of layered gradient Zr–Ti composite

To investigate potential strengthening approaches,multi-layered zirconium–titanium(Zr-Ti)composites were fabricated by hot-rolling bonding and annealing.The microstructures of these composites were characterized using scanning electron microscopy with energy dispersive spectroscopy(SEM-EDS)and electron backscatter diffractometry(EBSD).Their mechanical properties were evaluated by uniaxial tension and compression measurements.It was found that the fabricated Zr–Ti composites are composed of alternating Zr/diffusion/Ti layers,and chemical compositions of Zr and Ti showed a gradient distribution in the diffusion layer.Compared with as-rolled samples,annealing can strengthen the layered gradient Zr–Ti composite,and this is mainly caused by solid-solution strengthening and microstructure refinement-induced strengthening.Compared with the raw materials,a synergistic improvement of strength and ductility is achieved in the Zr–Ti composite as a result of the layered gradient microstructure.Tension–compression asymmetry is observed in the Zr–Ti composites,which may be attributed to twinning and microvoids induced by unbalanced diffusion.