Research on Anti-Fluctuation Control of Winding Tension System Based on Feedforward Compensation

In the fiber winding process,strong disturbance,uncertainty,strong coupling,and fiber friction complicate the winding constant tension control.In order to effectively reduce the influence of these problems on the tension output,this paper proposed a tension fluctuation rejection strategy based on feedforward compensation.In addition to the bias harmonic curve of the unknown state,the tension fluctuation also contains the influence of bounded noise.A tension fluctuation observer(TFO)is designed to cancel the uncertain periodic signal,in which the frequency generator is used to estimate the critical parameter information.Then,the fluctuation signal is reconstructed by a third-order auxiliary filter.The estimated signal feedforward compensates for the actual tension fluctuation.Furthermore,a time-varying parameters fractional-order PID controller(TPFOPID)is realized to attenuate the bounded noise in the fluctuation.Finally,TPFOPID is enhanced by TFO and applied to control a tension control system considering multi-source disturbances.The stability of the method is analyzed by using the Lyapunov theorem.Finally,numerical simulations verify that the proposed scheme improves the tracking ability and robustness of the system in response to tension fluctuations.

An ADRC Parameters Self-Tuning Control Strategy of Tension System Based on RBF Neural Network

High precision control of substrate tension is the premise and guarantee for producing high-quality products in roll-to-roll precision coating machine.However,the complex relationships in tension system make the problems of decoupling control difficult to be solved,which has limited the improvement of tension control accuracy for the coating machine.Therefore,an ADRC parameters self-tuning decoupling strategy based on RBF neural network is proposed to improve the control accuracy of tension system in this paper.Firstly,a global coupling nonlinear model of the tension system is established according to the composition of the coating machine,and the global coupling model is linearized based on the first-order Taylor formula.Secondly,according to the linear model of the tension system,a parameters self-tuning decoupling algorithm of the tension system is proposed by integrating feedforward control,ADRC and RBF.Finally,the simulation results show that the proposed tension control strategy has good decoupling control performance and effectively improves the tension control accuracy for the coating machine.

ELECTRO-HYDRAULIC COMPOUND CONTROL METHOD AND CHARACTERISTIC OF CONTROL FOR TENSION SYSTEM WITH HIGH INERTIA LOADS

Based on the pressure regulation circuit adopting electro-hydraulic proportional relief valve to control tension, a new type of electro-hydraulic compound control circuit with throttle control unit is presented, which can obtain optimal dynamic damping ratio through real-time altering pressure-flow gain of the throttle control unit, improve the dynamic characteristic of tension follow-up control for the tension system with high inertia loads. Moreover, the characteristic when the cable linear velocity variation causes change of tension is investigated, and a compound control strategy is proposed. The theoretical analysis and experimental results show that the electro-hydraulic compound control circuit is effective and the characteristic of the compound control strategy is satisfactory.

On the Mechanical Analysis and Control for the Tension System of the Cylindrical Filament Winding

The constant winding tension can make the filament arranged in order. The stress distribution between the filament balance fully gives play to the enhancement of filament, and increases the intensive workload of the composite winding material. This paper conducts the mechanical analysis for the unwinding roller and tension measuring roller of the cylindrical winding machine so that gets the mechanical model, gives error compensation formula caused by the radius change of the yarn group in the unwinding side, designs the closed-loop control system and utilizes the dynamical- integral PID control strategy to achieve the tension control during the process of the cylindrical winding.

Neurophysiological, histological, and behavioral characterization of animal models of distraction spinal cord injury: a systematic review

Distraction spinal cord injury is caused by some degree of distraction or longitudinal tension on the spinal cord and commonly occurs in patients who undergo corrective operation for severe spinal deformity.With the increased degree and duration of distraction,spinal cord injuries become more serious in terms of their neurophysiology,histology,and behavior.Very few studies have been published on the specific characteristics of distraction spinal cord injury.In this study,we systematically review 22 related studies involving animal models of distraction spinal cord injury,focusing particularly on the neurophysiological,histological,and behavioral characteristics of this disease.In addition,we summarize the mechanisms underlying primary and secondary injuries caused by distraction spinal cord injury and clarify the effects of different degrees and durations of distraction on the primary injuries associated with spinal cord injury.We provide new concepts for the establishment of a model of distraction spinal cord injury and related basic research,and provide reference guidelines for the clinical diagnosis and treatment of this disease.

Dynamic Simulation and Test Verifcation of Hydraulic Automatic Tensioner for an Engine Timing Chain Drive System

As a fundamental component of an automobile engine’s timing chain drive system, the hydraulic automatic tensioner signifcantly enhances fuel economy while minimizing system vibrations and noise. However, there is a noticeable lack of research on automatic hydraulic tensioners. This study presents a comprehensive calculation approach for the principal parameters of a hydraulic automatic tensioner. An efective method, grounded in hydraulics and multibody dynamics, was introduced for estimating the dynamic response of such a tensioner. The simulation model developed for the hydraulic tensioner is characterized by its rapid dynamic response, consistent operation, and high accuracy. The dynamic behavior of the tensioner was analyzed under varying boundary conditions, using sinusoidal signal excitation. It was observed that the maximum damping force increases with a decreasing leakage gap. Conversely, an increase in oil temperature or air content leads to a decrease in the maximum damping force. The reaction forces derived from these calculations align well with experimental results. This calculation and simulation approach ofers considerable value for the design of innovative hydraulic tensioners. It not only streamlines the design phase, minimizes the number of trials, and reduces product costs, but also provides robust insights for evaluating the performance of hydraulic tensioners.

Atomistic evaluation of tension–compression asymmetry in nanoscale body-centered-cubic AlCrFeCoNi high-entropy alloy

The tension and compression of face-centered-cubic high-entropy alloy(HEA) nanowires are significantly asymmetric, but the tension–compression asymmetry in nanoscale body-centered-cubic(BCC) HEAs is still unclear. In this study,the tension–compression asymmetry of the BCC Al Cr Fe Co Ni HEA nanowire is investigated using molecular dynamics simulations. The results show a significant asymmetry in both the yield and flow stresses, with BCC HEA nanowire stronger under compression than under tension. The strength asymmetry originates from the completely different deformation mechanisms in tension and compression. In compression, atomic amorphization dominates plastic deformation and contributes to the strengthening, while in tension, deformation twinning prevails and weakens the HEA nanowire.The tension–compression asymmetry exhibits a clear trend of increasing with the increasing nanowire cross-sectional edge length and decreasing temperature. In particular, the compressive strengths along the [001] and [111] crystallographic orientations are stronger than the tensile counterparts, while the [110] crystallographic orientation shows the exactly opposite trend. The dependences of tension–compression asymmetry on the cross-sectional edge length, crystallographic orientation,and temperature are explained in terms of the deformation behavior of HEA nanowire as well as its variations caused by the change in these influential factors. These findings may deepen our understanding of the tension–compression asymmetry of the BCC HEA nanowires.

Geometry and formation mechanism of tension gashes and their implication on the hydrocarbon accumulation in the deep-seated strata of sedimentary basin:A case from Shunnan area of Tarim Basin

With the theoretical and technological developments related to cratonic strike-slip faults,the Shuntuoguole Low Uplift in the Tarim Basin has attracted considerable attention recently.Affected by multi-stage tectonic movements,the strike-slip faults have controlled the distribution of hydrocarbon resources owing to the special fault characteristics and fault-related structures.In contrast,the kinematics and formation mechanism of strike-slip faults in buried sedimentary basins are difficult to investigate,limiting the discussion of these faults and hydrocarbon accumulation.In this study,we identified the characteristics of massive sigmoidal tension gashes(STGs)that formed in the Shunnan area of the Tarim Basin.High-resolution three-dimensional seismic data and attribute analyses were used to investigate their geometric and kinematic characteristics.Then,the stress state of each point of the STGs was calculated using seismic curvature attributes.Finally,the formation mechanism of the STGs and their roles in controlling hydrocarbon migration and accumulation were discussed.The results suggest that:(1)the STGs developed in the Shunnan area have a wide distribution,with a tensile fault arranged in an enéchelon pattern,showing an S-shaped bending.These STGs formed in multiple stages,and differential rotation occurred along the direction of strike-slip stress during formation.(2)Near the principal displacement zone of the strike-slip faults,the stress value of the STGs was higher,gradually decreasing at both ends.The shallow layer deformation was greater than the deep layer deformation.(3)STGs are critical for connecting source rocks,migrating oil and gas,sealing horizontally,and developing efficient reservoirs.This study not only provides seismic evidence for the formation and evolution of super large STGs,but also provides certain guidance for oil and gas exploration in this area.

Mechanical behavior of rock under uniaxial tension:Insights from energy storage and dissipation

Many rock engineering projects show that the growth of tensile cracks is often an important cause of engineering disasters,and the mechanical behavior of rocks is essentially the transmission,storage,dissipation and release of energy.To investigate the tensile behavior of rock from the perspective of energy,uniaxial tension tests(UTTs)and uniaxial compression tests(UCTs)were carried out on three typical rocks(granite,sandstone and marble).Different unloading points were set before the peak stress to separate elastic energy and dissipated energy.The input energy density ut,elastic energy density ue,and dissipated energy density ud at each unloading point were calculated by integrating stress-strain curves.The results show that there is a strong linear relationship between the three energy parameters and the square of the unloading stress in UCT,but this linear relationship is weaker in UTT.The ue and ud increase linearly with the increase in ut in UCT and UTT.Based on the phenomenon that ue and ud increase linearly with ut,the applicability of Wp et index in UTT was proved and the relative energy storage capacity and absolute energy distribution characteristics of three rocks in UCT and UTT were evaluated.The tensile behavior of marble and sandstone in UTT can be divided into two stages vaguely according to the energy distribution,but granite is not the case.In addition,based on dissipated energy,the damage evolution of three types of rocks in UCT and UTT was discussed.This study provides some new insights for understanding the tensile behavior of rock.

Near resonance vibration isolation on a levered-dual response(LEDAR)Coulomb-damped system by differential preloads/offsets in linear springs

The levered-dual response(LEDAR)Coulomb-damped system attains near resonant vibration isolation by differential preloads/offsets in linear springs.It takes the advantages of both the preloads/offsets in linear springs and the guiderail friction for realizing different levels of vibration isolation.The isolation capacities are investigated on the strategies with both the horizontal and vertical guiderails,with the horizontal rail only,and without guiderails.The compressive preloads generally result in the consumption of most of the initial excitation energy so as to overcome the potential threshold.The isolation onsets at the frequency ratio of 1∓0.095 on the left-hand side(LHS)and the right-hand side(RHS)of the lever are relative to the load plate connector.The observed near resonant isolation thus makes the LEDAR system a candidate for the isolation of the mechanical systems about resonance while opening a path for simultaneous harvesterisolation functions and passive functions at extreme frequencies.

Effectivity and safety of trifocal intraocular lenses and capsular tension rings implantation for cataract patients with axial high myopia

●AIM:To assess effectivity and safety of trifocal intraocular lenses(IOLs)and capsular tension rings in treating cataract patients with axial high myopia.●METHODS:A prospective nonrandomized controlled clinical trial was conducted.Totally 98 eyes(74 patients)who underwent femtosecond laser-assisted cataract surgery(FLACS)with trifocal IOLs were enrolled in the study and followed up for 2y after surgery:46 eyes(33 patients)with capsular tension ring implantation in the long axial lengths(AL)group(26<AL<29 mm)and 52 eyes(41 patients)in the normal AL group(22<AL<24.5 mm).Postoperative outcomes about effectivity and safety,including the subjective and objective visual quality,and postoperative complications were assessed.●RESULTS:Uncorrected distance visual acuity at 5 m and uncorrected intermediate visual acuity at 60 and 80 cm in the long AL group were significantly worse than those in the normal AL group at 3mo postoperatively(P<0.05).The differences in reading speed,spectacle independence and potential visual complaints between the two groups were not statistically significant(P>0.05).The dysfunctional lens index and total modulation transfer function(MTF)average height were similar between the two groups.The postoperative internal coma aberrations in the axial high myopia eyes were significantly higher than that in the normal AL group(P<0.05).The total satisfaction score in the long AL group(91.32±2.76)was slightly higher than that in the normal AL group(90.36±3.47),but there was no difference(P=0.136).A statistically negative correlation was found between corrected distance visual acuity(CDVA)and dysfunctional lens index(r=-0.382,P=0.009),and between CDVA and the total MTF average height(r=-0.374,P=0.01).But there was no significant correlation between CDVA and total satisfaction score(r=0.059,P=0.696).Postoperative complications mainly presented as posterior capsular opacity(PCO),retinal detachment and cystoid macular edema.There was no difference in the incidence of fundus disease(6.5%vs 3.8%,P=0.663)or PCO(17.4%vs 7.7%,P=0.217)between the two groups at two years.●CONCLUSION:The utilization of trifocal IOL and capsular tension ring implantation is beneficial for cataract patients with axial high myopia undergoing FLACS.This approach not only ensures excellent subjective feelings and objective visual quality,but also does not increase the incidence of postoperative complications.

Neuroimaging in atypical normal tension glaucoma:debating routine implementation in the absence of classic neurological findings

●AIM:To assess the necessity of neuroimaging in patients with neurological or atypical findings of normal tension glaucoma(NTG)who do not exhibit typical glaucoma manifestations.●METHODS:A retrospective analysis was conducted on 90 atypical NTG patients who underwent cranial magnetic resonance imaging(MRI)due to atypical symptoms.The demographic characteristics,clinical parameters,and radiological findings were recorded.●RESULTS:Among the patients,66.7%had abnormal radiology results,with the most common findings being gliosis(34.4%),sequelae of cerebrovascular events and vascular malformations(14.4%),and benign intracranial mass lesions(11%).Non-glaucomatous visual field defects were more frequently observed in patients with abnormal neuroimaging results.However,there were no significant differences in intraocular pressure,optic disc parameters,retinal nerve fiber layer thickness,and visual field indices between patients with normal and abnormal radiological results.The mean age of the patients was 58.74y.Interestingly,there was a significant age difference,with the abnormal radiology group having a higher median age(P=0.021).●CONCLUSION:The study highlights the importance of cranial imaging in older NTG patients to detect underlying pathologies and prevent misdiagnosis.It suggests that neuroimaging may be warranted in NTG patients with atypical visual field defects incompatible with glaucoma.However,routine neuroimaging in all NTG patients without classic neurological signs may not be necessary.

Unveiling the silent link:Normal-tension glaucoma's enigmatic bond with cardiac blood flow

This comprehensive review embarks on a captivating journey into the complex relationship between cardiology and normal-tension glaucoma(NTG),a condition that continues to baffle clinicians and researchers alike.NTG,characterized by optic nerve damage and visual field loss despite normal intraocular pressure,has long puzzled clinicians.One emerging perspective suggests that alterations in ocular blood flow,particularly within the optic nerve head,may play a pivotal role in its pathogenesis.While NTG shares commonalities with its high-tension counterpart,its unique pathogenesis and potential ties to cardiovascular health make it a fascinating subject of exploration.It navigates through the complex web of vascular dysregulation,blood pressure and perfusion pressure,neurovascular coupling,and oxidative stress,seeking to uncover the hidden threads that tie the heart and eyes together in NTG.This review explores into the intricate mechanisms connecting cardiovascular factors to NTG,shedding light on how cardiac dynamics can influence ocular health,particularly in cases where intraocular pressure remains within the normal range.NTG's enigmatic nature,often characterized by seemingly contradictory risk factors and clinical profiles,underscores the need for a holistic approach to patient care.Drawing parallels to cardiac health,we examine into the shared vascular terrain connecting the heart and the eyes.Cardiovascular factors,including systemic blood flow,endothelial dysfunction,and microcirculatory anomalies,may exert a profound influence on ocular perfusion,impacting the delicate balance within the optic nerve head.By elucidating the subtle clues and potential associations between cardiology and NTG,this review invites clinicians to consider a broader perspective in their evaluation and management of this elusive condition.As the understanding of these connections evolves,so too may the prospects for early diagnosis and tailored interventions,ultimately enhancing the quality of life for those living with NTG.

Eudragit®-PEG Nanoparticles: Physicochemical Characterization and Interfacial Tension Measurements

The objectives of this study are to understand the mechanisms involved in the stabilization of water/oil interfaces by polymeric nanoparticles (NPs) (Eudragit®). Eudragit L100 NPs of various sizes and Zeta potentials were studied and compared at a water/cyclohexane model interface using a droplet tensiometer (Tracker Teclis, Longessaigne, France). The progressive interfacial adsorption of the NPs in the aqueous phase was monitored by tensiometry. The model interface was maintained and observed in a drop tensiometer, analyzed via axisymmetric drop shape analysis (ADSA), to determine the interfacial properties. Given the direct relationship between the stability of Pickering emulsions (emulsions stabilized by solid nanoparticles) and the interfacial properties of these layers, different nanoparticle systems were compared. Specifically, Eudragit NPs of different sizes were examined. Moreover, the reduction of the Zeta potential with PEG-6000 induces partial aggregation of the NPs (referred to as NP flocs), significantly impacting the stability of the interfacial layer. Dynamic surface tension measurements indicate a significant decrease in interfacial tension with Eudragit® nanoparticles (NPs). This reduction correlates with the size of the NPs, highlighting that this parameter does not operate in isolation. Other factors, such as the contact angle and wettability of the nanoparticles, also play a critical role. Notably, larger NPs further diminished the interfacial tension. This study enhances our understanding of the stability of Pickering emulsions stabilized by Eudragit® L100 polymeric nanoparticles.

Impact of Tension-Type Headaches in the Workplace in Brazzaville

Introduction: Tension-type headaches are the most widespread of the primary headache disorders. Due to their high prevalence, tension-type headaches represent a major public health problem with an enormous socio-economic burden. Determining their impact remains a challenge. Objective: To assess the impact of occupational tension-type headache in Brazzaville and identify associated factors. Population and Methods: This was an analytical case-control study conducted in public and private companies in the city of Brazzaville over a period of four (04) months. The case population consisted of cephalalgic employees;the control population was drawn from the same companies and was free of tension-type headaches. Study variables were divided into socio-professional, clinical and individual impact variables. Individual impact variables were represented by: the HIT-6 score, which incorporates a very broad conception of disability, covering several domains, namely: severity of pain during attacks and the restrictive and limiting nature of attacks. Results: Individual impact was severe in 18 (62.1%) men and 11 (37.9%) women. Mean age was 36.3 6.14 years for cases with severe impact. The mean duration of headache was 40.3 32.7 months for cases with severe impact. Tension headache evolved in attacks in 22 (75.9%) cases with severe impact, and continuously in seven (24.1%) cases. The average number of attacks per month was 2.52 1.04 for cases with severe impact. Cases with severe impact included 14 (48.3%) with chronic headache and 15 (51.7%) with episodic headache. Pain of severe intensity present in 48.3% of cases was associated with a severe impact of tension-type headache: OR = 151.66 [2.36 - 44245.95] and p-value = 0.037. At least one days absence from work per year was observed in 47.4% of our cases. The number of days off work per year due to tension-type headache had an interquartile range between 0 and 3 days and extremes from 0 to 14 days. It was the consequence of a severe impact on daily and/or professional activities. Conclusion: The high frequency of tension-type headaches in the workplace and its impact on the condition of workers in Brazzaville represent a real public health problem. It was found that the number of days absent from work per year due to tension headaches was the consequence of a severe impact on daily and/or professional activities. An awareness-raising program in this environment seems necessary, as well as an assessment of working conditions.

The Tension Cosmology, Largest Cosmic Structures and Explosions of Supernovae from SST

Here, using the Scale-Symmetric Theory (SST) we explain the cosmological tension and the origin of the largest cosmic structures. We show that a change in value of strong coupling constant for cold baryonic matter leads to the disagreement in the galaxy clustering amplitude, quantified by the parameter S8. Within the same model we described the Hubble tension. We described also the mechanism that transforms the gravitational collapse into an explosion—it concerns the dynamics of virtual fields that lead to dark energy. Our calculations concern the Type Ia supernovae and the core-collapse supernovae. We calculated the quantized masses of the progenitors of supernovae, emitted total energy during explosion, and we calculated how much of the released energy was transferred to neutrinos. Value of the speed of sound in the strongly interacting matter measured at the LHC confirms that presented here model is correct. Our calculations show that the Universe is cyclic.

Hubble Tension Explanation from This Cosmological Model AΛΩ (Slow Bang Model, SB)

In this article we present a model of Hubble-Lemaître law using the notions of a transmitter (galaxy) and a receiver (MW) coupled to a model of the universe (Slow Bang Model, SB), based on a quantum approach of the evolution of space-time as well as an equation of state that retains all the infinitesimal terms. We find an explanation of the Hubble tension H0. Indeed, we have seen that this constant depends on the transceiver pair which can vary from the lowest observable value, from photons of the CMB (theoretical [km/s/Mpc]) to increasingly higher values depending on the earlier origin of the formation of the observed galaxy or cluster (ETG ~0.3 [Gy], ~74 [km/s/Mpc]). We have produced a theoretical table of the values of the constant according to the possible pairs of transmitter/receiver in the case where these galaxies follow the Hubble flow without large disturbance. The calculated theoretical values of the constant are in the order of magnitude of all values mentioned in past studies. Subsequently, we applied the models to 9 galaxies and COMA cluster and found that the models predict acceptable values of their distances and Hubble constant since these galaxies mainly follow the Hubble flow rather than the effects of a galaxy cluster or a group of clusters. In conclusion, we affirm that this Hubble tension does not really exist and it is rather the understanding of the meaning of this constant that is questioned.

Crealet presents its innovative warp tension solutions at Techtextil 2024

Crealet is the world leader in sophisticated warp feeding technology and tailored solutions.Controlled warp tension stands also for controlled fabric quality.The Swiss firm presents its latest developments for technical textile applications at Techtextil 2024 in Frankfurt,Germany.

A Comment on the Hubble Expansion Parameter Tension

We point out that the recent baryon acoustic oscillation measurement by the Dark Energy Survey collaboration relieves the Hubble expansion parameter tension.

Development of PLC-based Tension Control System

Fiber winding tension is an important factor in the molding techniques of composite material which influences the quality of winding product directly, and the tension control is a key technique in fiber winding techniques. This paper introduces a closed-loop tension control system with the programmable logic controller （PLC） with function modules as its control kernel, the alternating current （AC） servo motor as execute element and the radius-following device to accomplish the real-time radius compensation. The mechanism of the tension control system is analyzed and the numerical model is set up. The compensation technique of the radius of the scroll is analyzed. Experimental results show that the system is well qualified with high control precision and high reaction speed.