Effects of heavy metal ions Cu^(2+)/Pb^(2+)/Zn^(2+)on kinetic rate constants of struvite crystallization

Struvite(MAP)crystallization technology is widely used to treat ammonia nitrogen in waste effluents of its simple operation and good removal efficiency.However,the presence of heavy metal ions in the waste effluents causes problems such as slow crystallization rate and small crystal size,limiting the recovery rate and economic value of the MAP.The present study was conducted to investigate the effects of concentrations of three heavy metal ions(Cu^(2+),Zn^(2+),and Pb^(2+))on the crystal morphology,crystal size,average growth rate,and crystallization kinetics of MAP.A relationship was established between the kinetic rate constant Ktcalculated by the chemical gradient model and the concentrations of heavy metal ions.The results showed that low concentrations of heavy metal ions in the solution created pits on the MAP surface,and high level of heavy metal ions generated flocs on the MAP surface,which were composed of metal hydroxides,thus inhibiting crystal growth.The crystal size,average growth rate,MAP crystallization rate,and kinetic rate constant Ktdecreased with the increase in heavy metal ion concentration.Moreover,the Ktdemonstrated a linear relationship with the heavy metal concentration ln(C/C~*),which provided a reference for the optimization of the MAP crystallization process in the presence of heavy metal ions.

Experimental Study on Preparation of Natural Gas Hydrate by Crystallization

In this paper, the saturated solution crystallization method is proposed to promote the formation of hydrate by means of the known similarities between the hydrate formation process and the crystallization process. In this method,adding the second phase crystals was used to replace the spontaneous formation of hydrate crystal nuclei to form hydrate.The effects of saturated Na_2SO_4, MgSO_4, NH_4HCO_3 and CuSO_4 solutions on the formation rates of natural gas hydrate and gas storage capacity were investigated. The results showed that the saturated solution had an influence on the hydrate formation process. Under the given experimental conditions, the saturated Na_2SO_4 solution showed a highest increase in the hydrate formation rate, and the average hydrate formation rate in its presence was 11.8 times higher than that obtained in the deionized water. Moreover, the largest formation rate of gas hydrates observed in the saturated Na_2SO_4 solution was 386 times bigger than that in the deionized water, and the gas storage capacity increased by 10 times. In addition, the average hydrate formation rate in the saturated Mg SO_4 solution was faster than that in water by 20 times. The largest formation rate of gas hydrates in the saturated MgSO_4 solution was 165 times faster than that obtained in the deionized water, and the gas storage capacity increased by 6.2 times. The saturated NH_4HCO_3 and saturated CuSO_4 solutions also influenced the formation process of hydrate. Therefore, the crystallization method of saturated solution can be used to achieve a highefficiency preparation of natural gas hydrates, which provides theoretical guidance for the storage of natural gas in the form of hydrate.

Effect of cooling rate on the crystallization behavior of perovskite in high titanium-bearing blast furnace slag

The effect of cooling rate on the crystallization of perovskite in high Ti-bearing blast furnace（BF） slag was studied using confocal scanning laser microscopy（CSLM）. Results showed that perovskite was the primary phase formed during the cooling of slag. On the slag surface, the growth of perovskite proceeded via the successive production of quasi-particles along straight lines, which further extended in certain directions. The morphology and structure of perovskite was found to vary as a function of cooling rate. At cooling rates of 10 and 30 K/min, the dendritic arms of perovskite crossed obliquely, while they were orthogonal at a cooling rate of 20 K/min and hexagonal at cooling rates of 40 and 50 K/min. These three crystal morphologies thus obtained at different cooling rates respectively corresponded to the orthorhombic, cubic and hexagonal crystal structures of perovskite. The observed change in the structure of perovskite could probably be attributed to the deficiency of O^2-, when Ti2O3 was involved in the formation of perovskite.

Evolution mechanism of recrystallization in a nickel-based single crystal superalloy under various cooling rates during heat treatment

The recrystallization behaviors of a nickel-based single crystal superalloy during heat treatment at 1,200℃ for 4 h with various cooling rates were studied.Results show that the thickness of recrystallization layer decreases with the increase of cooling rate.In addition,the microstructures ofγ′phase in the recrystallization region are different in various cooling rates.In the high cooling rates(70,100℃·min^(-1)),small size and high volume fraction ofγ′phases are formed in the recrystallization region.It is also found that irregular fine secondaryγ′phases are precipitated between matrix channels with an average size of 150 nm in the original matric(100℃·min^(-1)).The sizes of the secondaryγ′phase decrease with the increase of cooling rate.In contrast,large size and small volume fraction ofγ′phases are formed in the recrystallization region,and a grain boundary layer is formed under a low cooling rate(10℃·min^(-1)).The evolution mechanism of recrystallization at various cooling rates during heat treatment is analyzed.

Determination of Crystallization Kinetics and Size Distribution Parameters of Agglomerated Calcium Carbonate Nanoparticles during the Carbonation of a Suspension of Lime

The reaction studied in this work is the synthesis of nanometric size calcium carbonate by carbonation of a suspension of lime, which represents the most common industrial route. The carbonation was proceeded in a pilot batch reactor. This article presents a method for the determination of nucleation and crystal growth rates of calcium carbonate by following two macroscopic parameters: the mass production rate by precipitation and the specific surface area. The results give a constant nucleation rate around 4 × 1015m-3 ·s-1 and a decreasing crystal growth rate between 0.2 and 2 × 10-10 m·s-1. It also provides the main characteristics of the monoparticle size distributions (i.e. the mean particle sizes and in situ coefficient of variation) in the agglomerates, which cannot be obtained by other known methods. For the carbonation carried out in this work, the mean mass particle size at the end of the reaction is about 300 nm and the coefficient of variation of 0.28 indicates a narrow particle size distribution of the monoparticles.

A MATHEMATICAL EXPRESSION OF CRYSTAL GROWTH RATE DURING CRYSTALLIZATION OF AMORPHOUS ALLOYS

A mathematical expression of the crystal growth rate during crystallization of the amorphous alloys was derived from the micromechanism of crystallization newly developed by the authors. Thus, the satisfactory explanation of the experimental results obtained by Nunogaki et al., Heimendahl et al. and the authors might be found. It seems also to be modelled with the expression for the crystal growth and the crystal size influenced by time during the crystallization of amorphous Ni-P alloy foil at in situ heating. Based on the expression, the factors influencing the crystal growth rate, such as temperature, time and microstructure of amorphous alloys have been discussed.

SOLIDIFICATION AND MICROSEGREGATION BEHAVIORS OF NICKEL-BASE SINGLE CRYSTAL SUPERALLOY SOLIDIFIED AT MEDIUM COOLING RATE

ＳＯＬＩＤＩＦＩＣＡＴＩＯＮＡＮＤＭＩＣＲＯＳＥＧＲＥＧＡＴＩＯＮＢＥＨＡＶＩＯＲＳＯＦＮＩＣＫＥＬＢＡＳＥＳＩＮＧＬＥＣＲＹＳＴＡＬＳＵＰＥＲＡＬＬＯＹＳＯＬＩＤＩＦＩＥＤＡＴＭＥＤＩＵＭＣＯＯＬＩＮＧＲＡＴＥ①ＤｕＷｅｉ，ＬｉＪｉａｎｇｕｏａｎ...

Effect of solidification rate on MC-type carbide morphology in single crystal Ni-base superalloy AM3

In order to study the effect of the withdrawing rate on carbide morphology,MC-type carbide in single crystal superalloy AM3 was systematically investigated with sample growth rates from 3.5 μm/s to 500 μm/s.The carbide morphologies were investigated by scanning electron microscopy(SEM),and the electron probe microanalysis(EPMA) was used to characterize the carbide composition.The results indicate that the solidification rate is the important factor governing MC carbide growth morphology,size and distribution,composition and growth mechanism.With the increase of withdrawing rate,nodular,rod-like,Chinese script types of carbide morphology are observed.For the low withdrawing rate,with the increase of withdrawing rate,the carbide size becomes larger.For the case of dendritic interface,the carbide size becomes smaller with refinement of dendrites as withdrawing rate increases.The volume fraction of carbides increases with the withdrawing rate increasing.

RECENT DOMESTIC PROGRESS IN SPACE CRYSTALLIZATION OF PROTEINS

The advances of protein crystal growth in microgravity are limited by its low success rate of space crystallization experiments. Our recent efforts have concentrated on exploration of the ways to increase the success rate of the experiments.The corresponding studies include structural comparisons of space- and Earthgrown protein crystals, numerical simulations of solute transport in protein crystallizer, optimization of protein crystailization conditions and improvement of crystallization techniques used. These studies show that the success rate of space protein crystallization could be improved by different ways.

Study of Growth Mechanism of Lysozyme Crystal by Batch Crystallization Method

The lysozyme crystals were made by batch crystallization method and the distribution of aggregate in solution were measured by dynamic light scattering. The results showed that the dimension of aggregate increased with the increase of the concentration of lysozyme and NaCl, lysozyme molecules aggregated gradually in solution and finally arrived at balance each other. The higher the concentrations of lysozyme and NaCl were, the faster the growth rate of （110） face was. The growth rates of lysozyme crystal were obtained by a Zeiss microscope, and the effective surface energy （a） of growing steps were calculated about 4.01×10^-8s J·cm^-2 according to the model of multiple two-dimensional nucleation mechanism.

Model of apparent crystal growth rate and kinetics of seeded precipitation from sodium aluminate solution

Based on the population balance equation in a batch crystallizer characteristic of seeded precipitation, a model to calculate the rate of apparent crystal growth of aluminum hydroxide from the size distribution was deve- loped. The simulation results indicate that the rate of apparent crystal growth during seeded precipitation exhibits a manifest dependence on the crystal size. In general, there is an obvious increase in the apparent crystal growth rate with the augment in crystal size. The apparent activation energy increases with the increase of characteristic crystal size, which indicates that the growth of small crystals is controlled by surface chemical reaction; it is gradually controlled by both the surface reaction and diffusion with the augment in crystal size.

Modification of spontaneous emission rate of micrometer-sized light sources using hollow-core photonic crystal fibers

We investigate numerically and experimentally the modification of the spontaneous emission rate for micrometersized light sources embedded in a hollow-core photonic crystal fiber （HCPCF）. The diameter of the light source is deliberately chosen such that they could be easily introduced into the central hole of the hollow-core photonic crystal fiber by capillary force. The photoluminescence from the microparticles is measured by using an inverted microscope in combination with a spectrometer. The modification of the spontaneous emission rate is observed in a wavelength region where there is no band gap. The experimental observations are consistent with the simulation results obtained by the plane wave expansion and finite-difference time-domain techniques.

Effects of Small Biomolecules on Lysozyme Crystallization

To develop appropriate biocompatible nucleants,glutathione(GSH),glycine(Gly)and cysteine(Cys)were used as the biomolecular additives to study their effect on the regulation of lysozyme crystallization.Characterized by Fourier transform infrared spectroscopy,powder X-ray diffraction,circular dichroism,etc.,the results show that GSH can effectively promote protein crystallization under even lower concentrations of lysozyme by enhancing the nucleation rate,comparing with the additives of Gly and Cys,whereas lysozyme crystal structures produced in the presence of the biomolecular additives are similar to those in the absence of the additives.It shows in combination with molecular modeling that the stronger interactions between small biomolecular additives and the lysozyme LOOP accelerate the heterogeneous nucleation.It is suggested that such small biomolecules can be used as promising nucleants for promoting protein crystallization in the food and pharmaceutical industries.

STRAIN RATE SENSITIVTTY OF POLYCRYSTALLINE AND SINGLE CRYSTAL NiAl

The compressive and tensile strain rate sensitivities of polycrystalline and single crystal NiAl have been evaluated at 877 ℃ which is well above DBTT. Samples were prepared to specific sizes by hot press consolidation of appropriate powder sizes and minimizing past consolidation thermal exposures. NiAl single crystals were grown in the [100]orientation using a modified Bridgeman technique. The yield and tensile strength of polycrystalline NiAl as a function of grain size generally follows a Hall-Petch type relationship . A tensile strain rate effect was found at strain rate of 1 to 10-4 sec-1. The strain rate sensitivity coefficient, m,in the equation of σ = Kε is in the range of 0. 10 to 0. 13. The highest strain rate (1 sec-1) resulted in significantly higher strengths and little or no observed ductility. Compressive strain rate testing al strain rate of 10-5to 10-2 sec-1 and at temperature of 1050°to 1250°K was conducted both for polycrystalline and for single crystal NiAl. The calculated stress exponents and the activation energy for creep were compared with the reference data.

KINETICS OF NON-ISOTHERMAL CRYSTALLIZATION OF NYLON-1010

The kineties of non-isothermal crystallization of Nylon-1010 has been investigated by using differential scanning calorimetry(DSC), DSC curves were obtained under cooling rate(R): 2. 5, 5, 10, 20, 40K/min. Applying Mandelkern and Ziabicki theories, the values of the Z kinetic parameter and G the kinetic crystalllzab- ility have been determined. Expenents of Avrami obtained in this work decrease with increase of cooling rate and then level off. The experimental results show disagreements with the Ozawa equation.

A Statistical Rate Theory of Interface Concentration during Solution ZeoliteCrystal Growth

A theoretical model is developed using statistical rate theory to determine the rate of molecular transport across the interface of a growing spherical zeolite crystal. The model is expressed in terms of the interface concentration. Two model constants appear in the expression for the equilibrium exchange rate. In order to validate the model, zeolite crystallization is investigated for a system for which experimental data exist. The model constants were first established using the measured growth rates at a specific temperature. Then the model was used to predict the growth rate at other temperatures.

Numerical Simulation of the Scavenging Rates of Ice Crystals of Various Microphysical Characteristics

Numerical models of trajectories of small aerosol spheres relative to oblate spheroids were used to determine ice crystal scavenging efficiencies. The models included the effects of aerodynamic flow about the ice particle, gravity, aerosol particle inertia and drag and electrostatic effects. Two electric configurations of the ice particle were investigated in detail. The first applied a net charge to the ice particle, of magnitude equal to the mean thunderstorm charge distribution, while the second applied a charge distribution, with no net charge, to the ice particle to model the electric multipole charge distribution. The results show that growing ice crystals with electric multipoles are better scavengers than single ice crystals with net thunderstorm charges, especially in the Greenfield gap (0.1 to 1.0 um), and that larger single crystals are better scavengers than smaller single crystals. The results also show that the low density ice crystals are more effective scavengers with net charges than they are with charge distribution.

The strain rate sensitive and anisotropic behavior of rare-earth magnesium alloy ZEK100 sheet

To overcome the limitation in formability at room temperature,manufacturers have developed magnesium alloys with remarkable properties by adding rare-earth elements.The rare-earth magnesium alloys behave differently from the conventional alloys,especially with respect to their coupled anisotropic and strain rate sensitive behavior.In the current work,such behavior of the rare-earth Mg alloy ZEK100 sheet at room temperature is investigated with the aid of the elastic viscoplastic self-consistent polycrystal plasticity model.Different strain rate sensitivities(SRSs)for various deformation modes are employed by the model to simulate the strain rate sensitive behaviors under different loading directions and loading rates.Good agreement between the experiments and simulations reveals the importance and necessity of using different SRSs for each deformation mode in hexagonal close-packed metals.Furthermore,the relative activities of each deformation mode and the texture evolution during different loadings are discussed.The anisotropic and strain rate sensitive behavior is ascribed to the various operating deformation modes with different SRSs during loading along different directions.