Experimental Study and Fragility Analysis of Effective-Length Factors in Column Buckling

The design of columns relies heavily on the basis of Leonhard Euler’s Theory of Elastic Buckling.However,to increase the accuracy in determining the maximum critical load a column can withstand before buckling,a constant was introduced.This dimensionless coefficient is K,also known as the effective-length factor.This constant is often found in building design codes and varies in value depending on the type of column support that is applied.This paper presents experimental and analytical studies on the determination of the effective-length factor in the buckling stability of columns with partially-fixed support conditions.To this end,the accurate K value of the columns tested by the Instron Testing Machine(ITM)at California State University,Northridge’s(CSUN’s)Mechanics Laboratory is determined.The ITM is used in studying the buckling of columns where the supports are neither pinned nor fixed,and the material cross-section rather rests upon the machine while loading is applied axially.Several column specimens were tested and the experimental data were analyzed in order to estimation of the accurate effective-length factor.The calculations from the tested results as well as the conducted probabilistic analysis shed light on how a fragility curve may aid in predicting the effective-length value of future tests.

An improved model of partition curve based on accumulation normal distribution function

Extensive studies based on partition curve of gravity separation have been investigated. All created models are merely used to simulate density distribution at the same size fraction. However, they cannot be used to predictive distribution of materials depending on compound feature of density and size. According to this situation, an improved model of partition curve based on accumulation normal distribution, which was distinguished from conventional model of accumulation normal distribution for partition curve, was proposed in this paper. It could simulate density distribution at different size fractions by using the density-size compound index and conflating the partition curves at different size fractions as one partition curve. The feasibility of three compound indexes, including mass index, settlement index and transformation index, were investigated. Specific forms of the improved model were also proposed. It is found that transformation index leads to the best fitting results, while the fitting error is only 1.75 according to the fitting partition curve.

Construction of a Normalized Full-Length cDNA Library of Sesame Developing Seed by DSN and SMART^(TM)

Sesame （Sesamue indicum L.） is one of the most important oilseed crops with high oil yield. Here, we described a simple and efficient method for constructing a normalized cDNA library from a high oil content cultivar of sesame Zhongzhi 14, during its oil accumulation stages. It combined switching mechanism at 5？end of RNA transcript （SMART） technique and duplex-specific nuclease （DSN） normalization methods. Double-stranded cDNAs were synthesized from mRNAs, processed by normalization and Sfi I restriction endonuclease, and finally the cDNAs were ligated to pDNR-LIB vector. The ligation mixture was transformed into Escherichia coli DH10B by electroporation. The capacity of the library was 1.0？06 clones in this library. Gel electrophoresis results indicated the fragments ranged from 700 to 2 000 bp, with the average size of 1 800 bp. Random picking clones showed that the recombination rate was 100%. The results showed that the cDNA library constructed successfully was a full-length library with high quality, and could be used to screen the genes related to development of oil synthesis.

Construction of a Normalized Full-Length cDNA Library of Cephalopod Amphioctopus fangsiao and Development of Microsatellite Markers

Amphioctopus fangsiao is one of the most economically important species and has been considered to be a candidate for aquaculture. In order to facilitate its fine-scale genetic analyses, we constructed a normalized full-length library successfully and developed a set of microsatellite markers in this study. The normalized full-length library had a storage capacity of 6.9×105 independent clones. The recombination efficiency was 95% and the average size of inserted fragments was longer than 1000 bp. A total of 3440 high quality ESTs were obtained, which were assembled into 1803 unigenes. Of these unigenes, 450(25%) were assigned into 33 Gene Ontology terms, 576(31.9%) into 153 Kyoto Encyclopedia of Genes and Genomes pathways, and 275(15.3%) into 22 Clusters of Orthologous Groups. Seventy-six polymorphic microsatellite markers were identified. The number of alleles per locus ranged from 4 to 17, and the observed and expected heterozygosities varied between 0.167 and 0.967 and between 0.326 and 0.944, respectively. Twelve loci were significantly deviated from Hardy-Weinberg equilibrium after Bonferroni correction and no linkage disequilibrium was found between different loci. This study provided not only a useful resource for the isolation of the functional genes, but also a set of informative microsatellites for the assessment of population structure and conservation genetics of A. fangsiao.

Research on Induction Normal Curvature and Critical Curves of Quasi－ellipsoidal Gear Drive with Inner－toroidal Teeth

Quasi-ellipsoidal gear drive is suitable for the precise flexible joint of robot,but some meshing problems of this transmission are rarely involved in the related papers.According to the two-parameter conjugate surface theory, this article studies on the induction normal curvature and critical curves, the method of analysis is efficient for not only the quasi-ellipsoidal gear drive but also the other types of spatial gear drive.

A NEW METHOD TO CONSTRUCT A FULL-LENGTH cDNA LIBRARY OF HUMAN NORMAL BLADDER TISSUE

Objective Using template switch mechanism at the 5’ end of mRNA technique (SMART) to construct a full length cDNA library of human normal bladder tissue. Methods The novel procedures used the template switching activity of powerscript reverse transcriptase to synthesize and anchor first strand cDNA in one step. Following reverse transcription, 5 cycles of PCR were performed using a modified oligo(dT) primer and an anchor primer to enrich the full length cDNA population with 1.0 g human normal bladder poly(A) + RNA, then double strand cDNA was synthesized. After digestion with sfiI and size fractionation by CHROMA SPIN 400 columns, double strand cDNA was ligated into λ TripIEx 2 vector and was packaged. We determined the titer of the primary library and the percentage of recombinant clones and finally amplified the library. Results The titer of the cDNA library constructed was 2.1×10 6 pfu·mL -1 , and the amplified cDNA library was 6×10 11 pfu·mL -1 , the percentage of recombination clones was 99%. Conclusion Using SMART technique helps us to construct full length cDNA library with high efficiency and high capacity which lays solid foundation for screening target genes of bladder diseases with probes and antibodies.

NORMAL CRITERIA FOR A FAMILY OF HOLOMORPHIC CURVES

In this paper,we extend the concept of holomorphic curves sharing hyperplanes and introduce definitions of restricted hyperplanes and partial shared hypersurfaces.Then,we prove several normal criteria of the family of holomorphic curves and holomorphic mappings that concern restricted hyperplanes and partial shared hypersurfaces.These results generalize the Montel-type normal criterion of holomorphic curves.

The Behavior of Normality when Iteratively Finding the Normal to a Line in an _lpGeometry

The normal direction to the normal direction to a line in Minkowski geometries generally does not give the original line. We show that in lp geometries with p>1?repeatedly finding the normal line through the origin gives sequences of lines that monotonically approach specific lines of symmetry of the unit circle. Which lines of symmetry that are approached depends upon the value of p and the slope of the initial line.

Shared Hyperplanes and Normal Families of Holomorphic Curves

In theorem LP [1], Liu proves the theorem when N = 2, but it can’t be ex-tended to the general case in his proof. So we consider the condition that the families of holomorphic curves share eleven hyperplanes, and we get the theorem 1.1.

Research on measuring time constant of NANMAC thermocouple

The theory for measuring the time constant of thermocouple was introduced, and the method for measuring the time constant of NANMAC thermocouple by using dynamic calibration system of transient surface temperature sensor was proposed. In this system, static and dynamic calibrations were conducted for infrared detectors and thermocouples, and then both temperature-time curves were obtained. Since the frequency response of infrared detector is superior to that of calibrat- ed thermocouple, the values measured by infrared detectors are taken as true values. Through dividing the values measured with thermocouples by those with infrared detectors, a normalized curve was obtained, based on which the time constant of thermocouple was measured. With this method, the experiments were carried out with NANMAC thermocouple to obtain its time constant. The results show that the method for measuring the time constant is feasible and the dynamic calibration of thermocouples can be achieved at microsecond and millisecond level. This research has a certain reference value for research and application of NANMAC thermocouple temperature sensor.

Optimal Rational Parameterization of Quadratic Curves Based on the Geographic Information of Both Ends

In this paper, we rewrote the equation of algebraic curve segmentswith the geometric informationonboth ends. The optimal or nearly optimal rationalparametric equation is determinedbythe principle that parametricspeedsat both endsareequal. Comparing withotherliteratures, the methodofthis paper has advantage in efficiency andiseasy to realize. The equation of optimal rational parameterization can be obtained directly by the information of both ends. Large numbers ofexperimental data show that our method hasbeen given withmore self-adaptability and accuracy than that ofotherliteratures, and if the parametricspeedat any end reaches its maximum or minimum value, the parameterization is optimal; otherwise itis close tooptimal rational parameterization.

Construction of Endpoint Constrained Cubic Rational Curve with Chord-Length Parameterization

This paper discusses the problem that constructing a curve to satisfy the given endpoint constraints and chord-length parameters. Based on the research of Lu, the curve construction method for the entire tangent angles region （α0, α1）∈（-r, r）×（-r, r） is given. Firstly, to ensure the weights are always positive, the three characteristics of cubic rational Bezier curve is proved, then the segment construction idea for the other tangent angles are presented in view of the three characteristics. The curve constructed with the new method satisfies the endpoint constraint and chord-length parameters, it＇s G1 continuous in every segment curve, and the shapes of the curve are well.

Runoff variations in the Luanhe River Basin during 1956-2002

The decrease of runoff in the Luanhe river basin, which caused water crisis in Tian-jin for several times, was investigated using discharge data covering the period 1956-2002. The data from the differential integral curves of the annual runoff indicate that the decreasing point began in 1979 in the six sub-basins. The decrease of runoff in the Luanhe river basin resulted from the combination of climate effects and human activities, in which the latter plays an important role. This can be illustrated by noting that after 1979 the runoff generated by similar precipitation decreased under the condition that the total precipitation did not decrease in the entire basin. As a result, the annual runoff of the Luanhe river basin after 1979 decreased by about 6.46×10^8 m^3 each year. To analyze the runoff characteristics, it is inadequate to seek the runoff trends only and the identification of cyclical component of the runoff as accurate as possible is necessary. From the natural annual runoff discharge time series, we can see the annual runoff fluctuates around the long-term average. Analyzed by VRL （Variable Record Length） method, the main periods of 3, 5-6, 7, 9, 16-20 and 37-39 years were found. The last decade causing water crisis was the driest period in the history, and this condition will last several years from trend analysis and power spectrum analysis. So finding new water sources is urgent to solve water crisis in Tianjin city, and the South-North Water Transfer is a feasible option.

Robust state-space realizations of digital filters against finite word length errors

This article deals with two important issues in digital filter implementation： roundoff noise and limit cycles. A novel class of robust state-space realizations, called normal realizations, is derived and characterized. It is seen that these realizations are free of limit cycles. Another interesting property of the normal realizations is that they yield a minimal error propagation gain. The optimal realization problem, defined as to find those normal realizations that minimize roundoff noise gain, is formulated and solved analytically. A design example is presented to demonstrate the behavior of the optimal normal realizations and to compare them with several well-known digital filter realizations in terms of minimizing the roundoff noise and the error propagation.

Size dependent free vibration analysis of functionally graded piezoelectric micro/nano shell based on modified couple stress theory with considering thickness stretching effect

Higher-order shear and normal deformation theory is used in this paper to account thickness stretching effect for free vibration analysis of the cylindrical micro/nano shell subjected to an applied voltage and uniform temperature rising.Size dependency is included in governing equations based on the modified couple stress theory.Hamilton’s principle is used to derive governing equations of the cylindrical micro/nano shell.Solution procedure is developed using Navier technique for simply-supported boundary conditions.The numerical results are presented to investigate the effect of significant parameters such as some dimensionless geometric parameters,material properties,applied voltages and temperature rising on the free vibration responses.

Some Key Technologies of a New-type CNC Curve Grinding Machine

This paper presented a new-type CNC curve grinding machine, in order to conquer the disadvantages of conventional NC curve grinding machine and improve surface quality, dimensional accuracy and machining efficiency. The new-type grinder adopts some high and new technologies: ① the normal tracing device could make grinding wheel coincide with the normal direction of the machining points in work piece, and improve surface quality and dimensional accuracy; ② the digital image on-line recognition system could monitor machining process and compensate wheel wear in real time; ③ linear motor drive mechanism could realize the exact adjustment of the grinding head digitally and increase the machining efficiency. The math models of normal tracing and circular tolerance zone were presented. The experimental results show that the new-type CNC curve grinding machine equipped with the three devices mentioned above is easy to realize the precision grinding of any complex curve, and improve surface quality, dimensional accuracy and machining efficiency.

Stress analysis of full-length grouted bolt under shear deformation of anchor interface

The bolt anchoring force is closely related to the shear properties of the anchor interface. The shear stress distribution of full-length grouted bolts is analyzed based on the stress-strain relationship among the bolt, grout, rock mass and bond interface,considering the shear properties of the grout and contact interface bonding behavior. In this case, the interfacial shear stress of the grout and rock mass and the bolt axial force are obtained under pull-out and normal working conditions. The results show that the peak shear stress of the interface with the shear deformation of the bond interface is significantly lower than that without it when the pull-out force is applied. When designing bolt parameters of grade IV and V rock mass, the relative deformation between the rock mass and anchor should be considered, with a “unimodal” to “bimodal” shear stress distribution.In the case of a low elastic modulus of rock masses,both the shear stress concentration and distribution range are obvious, and the neutral point is near the bolt head. As the elastic modulus increases, the shear stress concentration and distribution range are reduced, and the neutral point moves towards the distal end. As a result, the optimum length of fulllength grouted bolts can be determined by in-situ pull-out tests and decreases with the increased elastic modulus of the rock mass.

Attenuation-type and failure-type curve models on accumulated pore water pressure in saturated normal consolidated clay

Based on dynamic triaxial test results of saturated soft clay, similarities of variations between accumulated pore water pressure and accumulated deformation were analyzed. The Parr＇s equation on accumulated deformation was modified to create an attenuation-type curve model on accumulated pore water pressure in saturated normal consolidation clay. In this model, dynamic strength was introduced and a new parameter called equivalent dynamic stress level was added. Besides, based on comparative analysis on variations between failure-type and attenuatiun-type curves, a failure-type curve model was created on accumulated pore water pressure in saturated normal consolidation clay. Two models can take cycle number, coupling of static and dynamic deviator stress, and consolidation way into consideration. The models are verified by test results. The correlation coefficients are more than 0.98 for optimization of test results based on the two models, and there is good agreement between the optimized and test curves, which shows that the two models are suitable to predict variations of accumulated pore water pressure under different loading cases and consolidation ways. In order to improve prediction accuracy, it is suggested that loading cases and consolidation ways should be consistent with in-situ conditions when dynamic triaxial tests are used to determine the constants in the models.

基于正态变换的变样本容量Shewhart比例控制图设计

为了提高Shewhart型比例控制图的监控效率,将其与变样本容量策略结合,提出一种新的比例控制图(VSS Shewhart-RZ*控制图)来监控二元正态变量之比。基于正态变换方法设计了新的比例统计量Z*,以消除样本容量变化对比例控制图设计及使用的不利影响。采用马尔科夫链方法计算了该控制图的平均运行长度和平均样本容量,给出该控制图的参数优化算法。通过仿真分析研究了该控制图的统计性能,并与Shewhart比例控制图进行比较,结果表明VSS Shewhart-RZ*控制图的性能明显优于传统固定样本容量Shewhart比例控制图。

Withdraw: Improvement on Adhesion Properties of Insert Injection Molding Composites: Effect of Inserted Parts, Adhesive Lengths and Injection Conditions

Short Retraction Notice The paper does not meet the standards of "Open Journal of Composite Materials". This article has been retracted to straighten the academic record. In making this decision the Editorial Board follows COPE's Retraction Guidelines. The aim is to promote the circulation of scientific research by offering an ideal research publication platform with due consideration of internationally accepted standards on publication ethics. The Editorial Board would like to extend its sincere apologies for any inconvenience this retraction may have caused. Editor guiding this retraction: Prof. Chengye Fan (EiC of OJCM) The full retraction notice in PDF is preceding the original paper, which is marked "Withdraw".