Numerical and Experimental Analysis of the Aerodynamic Torque for Axle-Mounted Train Brake Discs

As the velocity of a train increases,the corresponding air pumping power consumption of the brake discs increases proportionally.In the present experimental study,a standard axle-mounted brake disc with circumferential pillars was analyzed using a 1:1 scale model and a test rig in a wind tunnel.In particular,three upstream velocities were selected on the basis of earlier investigations of trains operating at 160,250,and 400 km/h,respectively.Moreover,3D steady computational fluid dynamics(CFD)simulations of the flow field were conducted to compare with the wind tunnel test outcomes.The results for a 3-car train at 180 km/h demonstrated:(1)good agreement between the air resistance torques obtained from the wind tunnel tests and the related numerical results,with differences ranging from 0.95%to 5.88%;(2)discrepancies ranging from 3.2 to 3.8 N·m;(3)cooling ribs contributing more than 60%of the air resistance torque;(4)the fast rotation of brake discs causing a significantly different flow field near the bogie area,resulting in 25 times more air pumping power loss than that obtained in the stationary brake-disc case.

An Investigation into the Effects of the Reynolds Number on High-Speed Trains Using a Low Temperature Wind Tunnel Test Facility

A series of tests have been conducted using a Cryogenic Wind Tunnel to study the effect of Reynolds number(Re)on the aerodynamic force and surface pressure experienced by a high speed train.The test Reynolds number has been varied from 1 million to 10 million,which is the highest Reynolds number a wind tunnel has ever achieved for a train test.According to our results,the drag coefficient of the leading car decreases with higher Reynolds number for yaw angles up to 30º.The drag force coefficient drops about 0.06 when Re is raised from 1 million to 10 million.The side force is caused by the high pressure at the windward side and the low pressure generated by the vortex at the lee side.Both pressure distributions are not appreciably affected by Reynolds number changes at yaw angles up to 30°.The lift force coefficient increases with higher Re,though the change is small.At a yaw angle of zero the down force coefficient is reduced by a scale factor of about 0.03 when the Reynolds number is raised over the considered range.At higher yaw angles the lift force coefficient is reduced about 0.1.Similar to the side force coefficient,the rolling moment coefficient does not change much with Re.The magnitude of the pitching moment coefficient increases with higher Re.This indicates that the load on the front bogie is higher at higher Reynolds numbers.The yawing moment coefficient increases with Re.This effect is more evident at higher yaw angles.The yawing moment coefficient increases by about 6%when Re is raised from 1 million to 10 million.The influence of Re on the rolling moment coefficient around the leeward rail is relatively smaller.It increases by about 2%over the considered range of Re.

Torque effect on vibration behavior of high-speed train gearbox under internal and external excitations

The high-speed train transmission system,experiencing both the internal excitation originating from gear meshing and the external excitation originating from the wheel-rail interaction,exhibits complex dynamic behavior in the actual service environment.This paper focuses on the gearbox in the high-speed train to carry out the bench test,in which various operat-ing conditions(torques and rotation speeds)were set up and the excitation condition covering both internal and external was created.Acceleration responses on multiple positions of the gearbox were acquired in the test and the vibration behavior of the gearbox was studied.Meanwhile,a stochastic excitation modal test was also carried out on the test bench under different torques,and the modal parameter of the gearbox was identified.Finally,the sweep frequency response of the gearbox under gear meshing excitation was analyzed through dynamic modeling.The results showed that the torque has an attenuating effect on the amplitude of gear meshing frequency on the gearbox,and the effect of external excitation on the gearbox vibration cannot be ignored,especially under the rated operating condition.It was also found that the torque affects the modal param-eter of the gearbox significantly.The torque has a great effect on both the gear meshing stiffness and the bearing stiffness in the transmission system,which is the inherent reason for the changed modal characteristics observed in the modal test and affects the vibration behavior of the gearbox consequently.

Safety of the express freight train running over a long-span bridge

Purpose-Express freight transportation is in rapid development currently.Owing to the higher speed of express freight train,the deformation of the bridge deck worsens the railway line condition under the action of wind and train moving load when the train runs over a long-span bridge.Besides,the blunt car body of vehicle has poor aerodynamic characteristics,bringing a greater challenge on the running stability in the crosswind.Design/methodology/approach-In this study,the aerodynamic force coefficients of express freight vehicles on the bridge are measured by scale model wind tunnel test.The dynamic model of the train-long-span steel truss bridge coupling system is established,and the dynamic response as well as the running safety of vehicle are evaluated.Findings-The results show that wind speed has a significant influence on running safety,which is mainly reflected in the over-limitation of wheel unloading rate.The wind speed limit decreases with train speed,and it reduces to 18.83 m/s when the train speed is 160 km/h.Originality/value-This study deepens the theoretical understanding of the interaction between vehicles and bridges and proposes new methods for analyzing similar engineering problems.It also provides a new theoretical basis for the safety assessment of express freight trains.

Robust Parameter Identification Method of Adhesion Model for Heavy Haul Trains

A robust parameter identification method based on Kiencke model was proposed to solve the problem of the parameter identification accuracy being affected by the rail environment change and noise interference for heavy-duty trains. Firstly, a Kiencke stick-creep identification model was constructed, and the parameter identification task was transformed into a quadratic programming problem. Secondly, an iterative algorithm was constructed to solve the problem, into which a time-varying forgetting factor was added to track the change of the rail environment, and to solve the uncertainty problem of the wheel-rail environment. The Granger causality test was adopted to detect the interference, and then the weights of the current data were redistributed to solve the problem of noise interference in parameter identification. Finally, simulations were carried out and the results showed that the proposed method could track the change of the track environment in time, reduce the noise interference in the identification process, and effectively identify the adhesion performance parameters.

Experimental and Numerical Investigation on the External Aerodynamic Noise of High-Speed Train

Aerodynamic noise is the dominant noise source of the high-speed train.It not only seriously affects the passenger comfort and people’s normal life along the railway line,but also may cause fatigue damage to the surrounding equipment and buildings.This manuscript carried out the simulation and experimental study on the external aerodynamic noise of high-speed train,in order to increase the understanding of the noise and hence to be better able to control it.The on-line tests were performed to verify that it is reasonable to simplify the high-speed train model.The turbulent air flow model was then developed,and the external steady flow field was computed by Realizable k-εturbulence model.Based on the steady flow field,aerodynamic noise sources on the train surface and the external transient flow field were calculated by broadband acoustics source model and large eddy simulation(LES)respectively.The pressures on the train surface were obtained from the results of the transient model.Considering the transient flow field,the far-field aerodynamic noise generated by the high-speed train was finally obtained based on Lighthill-Curle theory.Through the comparison between simulations and on-line tests,it is shown that the numerical model gives reliable aerodynamic noise predictions.This research is significant to the study and control of the aerodynamic noise of high-speed train.

Wind tunnel tests on aerodynamic characteristics of vehicles on same-storey highway and rail bridge under crosswind

In recent years,the safety and comfort of road vehicles driving on bridges under crosswinds have attracted more attention due to frequent occurrences of wind-induced disasters.This study focuses on a container truck and CRH2 high-speed train as research targets.Wind tunnel experiments are performed to investigate shielding effects of trains on aerodynamic characteristics of trucks.The results show that aerodynamic interference between trains and trucks varies with positions of trains(upstream,downstream)and trucks(upwind,downwind)and numbers of trains.To summarize,whether the train is upstream or downstream of tracks has basically no effect on aerodynamic forces,other than moments,of a truck driving on windward sides of bridges(upwind).In contrast,the presence of trains on the bridge deck has a significant impact on aerodynamic characteristics of a truck driving on leeward sides(downwind)at the same time.The best shielding effect on lateral forces of trucks occurs when the train is located downstream of tracks.Finally,the pressure measuring system shows that only lift forces on trains are affected by trucks,while other forces and moments are primarily affected by adjacent trains.

Aerodynamic characteristics of moving vehicles of two trains passing each other on bridge under crosswinds

Two trains passing each other is controlling factor for the wind-vehicle-bridge systems.To test the aerodynamic characteristics of moving vehicles under crosswinds when two trains are passing each other,a wind tunnel test device,which has two moving tracks,was developed.The rationality of the test result was discussed,the effects of intersection mode,yaw angle and lane spacing on the aerodynamic coefficients of the leeward train were analyzed,and the difference of aerodynamic coefficients between the head vehicle and the tail vehicle was discussed.The results show that the proposed test device has good repeatability.The intersection modes have a certain effect on the aerodynamic force of the leeward train when two trains are passing each other,and the results should be more reasonable during the two trains dynamic passing each other.With the decrease of yaw angle,the sudden change of train aerodynamic coefficients is more obvious.The decrease of lane spacing will increase the sudden change of leeward vehicles.In the process of two trains passing each other,the aerodynamic coefficients of the head vehicle and tail vehicle are significantly different,so the coupling vibration analysis of wind-vehicle-bridge system should be considered separately.

Test of incremental respiratory endurance as home-based, standalone therapy in chronic obstructive pulmonary disease: A case report

BACKGROUND The prevalence of chronic obstructive pulmonary disease(COPD)is increasing worldwide,and at the same time it is associated with increased mortality and reduced quality of life.Efforts to build sustainable rehabilitation approaches to COPD treatment and prevention are crucial.The system of long-term pulmonary rehabilitation care is insufficient.The main reasons for the absence of these outpatient programs are the lack of experience,the lack of interest of insurance companies in secondary prevention programs,and the lack of healthcare facilities in large geographical areas.The possibility of at-home pulmonary rehabilitation models(telemonitoring and telecoaching)could solve this problem.CASE SUMMARY A 71-year-old man with severe COPD,Global Initiative for Obstructive Lung Diseases stage 3 underwent an 8-wk remotely monitored inspiratory muscle training with a device based on the test of incremental respiratory endurance method.Spirometry,body plethysmography,test of incremental respiratory endurance examination,6-min walking test,body mass index,airflow obstruction,dyspnea,exercise capacity index,and subjective perception of dyspnea were performed as part of the initial and final examination.The patient performed training at home,and the physiotherapist monitored the patient remotely through a web application that allowed the physiotherapist to evaluate all training parameters in real-time and respond to any problems.After 8 wk of home training,there was a significant increase in all monitored values:maximal inspiratory pressure,a novel parameter sustained maximal inspiratory pressure,forced expiratory volume in 1 s,total lung capacity,forced vital capacity,peak expiratory flow,and inspiratory capacity.There was also an improvement in the perception of dyspnea according to the COPD Assessment Test and a modified Medical Research Council Breathlessness Scale,an increase in exercise tolerance according to the 6-min walking test,and a decrease in the exercise capacity index as a predictor of prognosis.CONCLUSION Respiratory telerehabilitation was greatly beneficial in a cooperative patient with COPD and may represent an alternative therapeutic approach to the increasing incidence of all lung diseases.

Validation and Implementation of the Lactate Minimum Test in Rowing

LMT （lactate minimum test） was found to be a valid and reliable testing concept for different sport disciplines. The aim of this study was to implement and validate the LMT in rowing due to considerable advantages for athletes and coaches compared to other established testing concepts in rowing. Twenty healthy and experienced male rowers completed two LMTs, one 2,000 m all-out trial and several endurance tests for MLSS （maximal lactate steady-state） determination on a rowing ergometer. For all tests performance, VO2, heart rate and lactate concentration were monitored. CV （coefficients of variation） for performance, heart rate and VO2 were all below 3.5% indicating a high reproducibility for these parameters at LM （lactate minimum） as well as at LMTpeak. Only lactate concentrations were revealed not to be well reproducible （CV 〉 12%）. Performance at LM and MLSS showed a significant correlation （r2 = 0.660; P 〈 0.001）. Comparison between data at LMTpeak and the 2,000 m time trial revealed a high correlation between performance and VO2peak data （performance： r2 = 0.923; P 〈 0.001, VO2peak： r2 = 0.860; P 〈 0.001）. We conclude that the present LMT protocol allows assessment of VO2peak, MLSS and prediction of 2,000 m race performance based on one single test. Therefore, our LMT protocol represents a reliable and valid diagnostic tool for steering and monitoring the training process in rowing.

A Full Mission Simulator of the Ship＇s Automated Electric Power System for Training and Competence Testing of Marine Engineers

This article describes practical preparation of marine engineers on the full mission simulator complex of the ship＇s automated electrical power plant. A full mission simulator complex of the ship＇s automated power management system meets International Convention STCW （Standards of Training, Certification and Watchkeeping） 78 （with Manila amendments 2010） requirements in part of adequate reproduction of its operational modes corresponding to the actual configuration and layout of the ship＇s automated power management system with real consumers and typical loads. The simulator is fully consistent with the goals and objectives of the practical training, as well as the goals and objectives of proficiency testing engine department officers on issues of technical maintenance of real ship＇s equipment （high voltage installations included） and means of automation. The simulator＇s complex is designed for training and proficiency testing of cadets and students of maritime educational institutions, as well as training and proficiency testing of marine specialists （mechanics and electricians） by watch-keeping and maintenance of modem integrated automated control systems of ship＇s electric power plant and the individual ship electromechanical systems, including high-voltage systems. A simulator＇s complex provides adequate reproduction of operational situations on technical side of real ship electric and automation equipment provides training on monitoring, control and management diesel-generator sets in hand, semi-automatic and automatic modes of power station, control and management of electromechanical systems, as well as the set of tasks upon parameterization, visualization and etc. Besides number of combinations of monitoring, control and management tasks, the simulator＇s complex provides an opportunity to simulate various practical fault conditions. It allows students to focus on the work of automatic control system in emergency situations and to work out correct actions for a watch-keeper on searching, localizing of faults and troubleshooting of equipment.

Model tests on XCC-piled embankment under dynamic train load of high-speed railways

Piled embankments,which offer many advantages,are increasingly popular in construction of high-speed railways in China.Although the performance of piled embankment under static loading is well-known,the behavior under the dynamic train load of a high-speed railway is not yet understood.In light of this,a heavily instrumented piled embankment model was set up,and a model test was carried out,in which a servo-hydraulic actuator outputting M-shaped waves was adopted to simulate the process of a running train.Earth pressure,settlement,strain in the geogrid and pile and excess pore water pressure were measured.The results show that the soil arching height under the dynamic train load of a high-speed railway is shorter than under static loading.The growth trend for accumulated settlement slowed down after long-term vibration although there was still a tendency for it to increase.Accumulated geogrid strain has an increasing tendency after long-term vibration.The closer the embankment edge,the greater the geogrid strain over the subsoil.Strains in the pile were smaller under dynamic train loads,and their distribution was different from that under static loading.At the same elevation,excess pore water pressure under the track slab was greater than that under the embankment shoulder.

Retrospective study of effect of whole-body vibration training on balance and walking function in stroke patients

BACKGROUND Dysfunction in stroke patients has been a problem that we committed to solve and explore.Physical therapy has some effect to regain strength,balance,and coordination.However,it is not a complete cure,so we are trying to find more effective treatments.AIM To observe the effect of whole-body vibration training(WVT)on the recovery of balance and walking function in stroke patients,which could provide us some useful evidence for planning rehabilitation.METHODS The clinical data of 130 stroke participants who underwent conventional rehabilitation treatment in our hospital from January 2019 to August 2020 were retrospectively analyzed.The participants were divided into whole-body vibration training(WVT)group and non-WVT(NWVT)group according to whether they were given WVT.In the WVT group,routine rehabilitation therapy was combined with WVT by the Galileo Med L Plus vibration trainer at a frequency of 20 Hz and a vibration amplitude of 0+ACY-plusmn+ADs-5.2 mm,and in the NWVT group,routine rehabilitation therapy only was provided.The treatment course of the two groups was 4 wk.Before and after treatment,the Berg balance scale(BBS),3 m timed up-and-go test(TUGT),the maximum walking speed test(MWS),and upper limb functional reaching(FR)test were performed.RESULTS After 4 wk training,in both groups,the BBS score and the FR distance respectively increased to a certain amount(WVT=46.08±3.41 vs NWVT=40.22±3.75;WVT=20.48±2.23 vs NWVT=16.60±2.82),with P<0.05.Furthermore,in the WVT group,both BBS score and FR distance(BBS:18.32±2.18;FR:10.00±0.92)increased more than that in the NWVT group(BBS:13.29±1.66;FR:6.16±0.95),with P<0.05.Meanwhile,in both groups,the TUGT and the MWS were improved after training(WVT=32.64±3.81 vs NWVT=39.56±3.68;WVT=12.73±2.26 vs NWVT=15.04±2.27,respectively),with P<0.05.The change in the WVT group(TUGT:17.49±1.88;MWS:6.79±0.81)was greater than that in the NWVT group(TUGT:10.76±1.42;MWS:4.84±0.58),with P<0.05.CONCLUSION The WVT could effectively improve the balance and walking function in stroke patients,which may be good for improving their quality of life.

Aerodynamic characteristics of a high-speed train crossing the wake of a bridge tower from moving model experiments

In a strong crosswind,the wake of a bridge tower will lead to an abrupt change of the aerodynamic forces acting on a vehicle passing through it,which may result in problems related to the transportation safety.This study investigates the transient aerodynamic characteristics of a high-speed train moving in a truss girder bridge and passing by a bridge tower in a wind tunnel.The scaled ratio of the train,bridge,and tower are 1:30.Effects of various parameters such as the incoming wind speed,train speed,and yaw angle on the aerodynamic performance of the train were considered.Then the sudden change mechanism of aerodynamic loads on the train when it crosses over the tower was further discussed.The results show that the bridge tower has an apparent shielding effect on the train passing through it,with the influencing width being larger than the width of the tower.The train speed is the main factor affecting the influencing width of aerodynamic coefficients,and the mutation amplitude is mainly related to the yaw angle obtained by changing the incoming wind speed or train speed.The vehicle movement introduces an asymmetry of loading on the train in the process of approaching and leaving the wake of the bridge tower,which should not be neglected.

Fatigue Characterization on a Cast Aluminum Beam of a High-Speed Train Through Numerical Simulation and Experiments

The cast aluminum beam is a key structure for carrying the body-hung traction motor of a high-speed train;its fatigue property is fundamental for predicting the residual life and service mileage of the structure.To characterize the structural fatigue property,a finite element-based method is developed to compute the stress concentration factor,which is used to obtain the structural fatigue strength reduction factors.A full-scale fatigue test on the cast aluminum beam is designed and implemented for up to ten million cycles,and the corresponding finite element model of the beam is validated using the measured data of the gauges.The results show that the maximum stress concentration occurs at the fillet of the supporting seat,where the structural fatigue strength reduction factor is 2.45 and the calculated fatigue limit is 35.4 MPa.Moreover,no surface cracks are detected using the liquid penetrant test.Both the experimental and simulation results indicate that the cast aluminum beam can satisfy the service life requirements under the designed loading conditions.

Wheel wear comparison between motor car and trailer of intercity train

To analyze wheel wear discrepancy between motor car and trailer of an intercity train,a novel wheel wear rates calculation model was proposed,which was composed of the intercity train dynamics model,wheel-rail three-dimensional rolling contact FEM model and the wear model.The simulated results were contrasted with measured results in field test.The simulated results showed the motor car wheels had larger rotation rate and longitudinal creepage than the trailer wheels.Meanwhile,the motor car wheels encountered larger vertical forces and longitudinal forces from bogie because of the heavier car body and the impact of traction torque.The traction torque acting on motor car wheel could increase the slip rates in the rear part of wheel contact patch and weaken the spinning phenomenon of relative slip.Larger contact pressure and slip rates caused the higher wear rates of motor car wheel than those of trailer wheel.The overall trends of wheel wear depth in simulated and tested results were similar.And they both showed the motor car wheel encountered the more serious wear than the trailer wheel.These models can be used to study the effect of the traction characteristics curves on the wear of wheel.

Comparative Analysis of Machine Learning Models for PDF Malware Detection:Evaluating Different Training and Testing Criteria

The proliferation of maliciously coded documents as file transfers increase has led to a rise in sophisticated attacks.Portable Document Format(PDF)files have emerged as a major attack vector for malware due to their adaptability and wide usage.Detecting malware in PDF files is challenging due to its ability to include various harmful elements such as embedded scripts,exploits,and malicious URLs.This paper presents a comparative analysis of machine learning(ML)techniques,including Naive Bayes(NB),K-Nearest Neighbor(KNN),Average One Dependency Estimator(A1DE),RandomForest(RF),and SupportVectorMachine(SVM)forPDFmalware detection.The study utilizes a dataset obtained from the Canadian Institute for Cyber-security and employs different testing criteria,namely percentage splitting and 10-fold cross-validation.The performance of the techniques is evaluated using F1-score,precision,recall,and accuracy measures.The results indicate that KNNoutperforms other models,achieving an accuracy of 99.8599%using 10-fold cross-validation.The findings highlight the effectiveness of ML models in accurately detecting PDF malware and provide insights for developing robust systems to protect against malicious activities.

The Importance of Professional Training for Test Writers

The purpose of this essay was to explore the importance of professional training for test writers and teachers as well.Since both testing and teaching are so closely interrelated that it's impossible to work in either field without being constantly concerned with the other. Test writers need professional training to keep pace with emergence of new views of language teaching practice and the rapid change of social life, in order to make testing more authentic and more valid.

Effectiveness of a Training Program for Improving Public Health Nurses’ Attitudes and Confidence in Dealing with Men Who Have Sex with Men

Objective: This study examined the effect of an educational intervention on public health nurses’ attitudes and confidence in dealing with men who have sex with men (MSM). In Japan, HIV is primarily transmitted through sexual contact between men, and free HIV testing and counseling are provided by public health nurses. However, because of a lack of education, public health nurses do not often recognize the existence of MSM in daily life. Thus, improving public health nurses’ understanding of MSM is crucial. Methods: This study used a quasi-experimental design to examine public health nurses’ homophobia, confidence in dealing with MSM, and low awareness of MSM in daily life at pre-test, post-test, and 1 and 3 months follow-ups. The intervention comprised a 3-hour training session conducted between November 2012 and September 2013 in the Kinki region. Results: A total of 124 public health nurses participated in the training, 117 of which were allocated to the intervention group;182 public health nurses who did not participate in the training session were allocated to a control group. Homophobia scores had significantly decreased at post-test, and remained at that low level by the follow-up at 3 months (pre-test to post-test;p = 0.00, post-test to 1 month;p = 0.83, 1 month to 3 months;p = 0.64, pre-test to 3 months;p = 0.00). Confidence in dealing with MSM and recognition of MSM had significantly increased by post-test;these were also maintained by the follow-up at 3 months (pre-test to post-test;p = 0.0, post-test to 1month;p = 0.18, 1 to 3 months;p = 0.44, pre-test to 3 months;p = 0.0). Discussion: While the three-hour training session was short, it was effective for improving attitudes toward MSM and building confidence in dealing with them.

Reflections on Language Testing——From the Perspective of Professional Training for Test Writers

This paper aims to talk about the superficial reflections on language testing from the perspective of professional training for test writers,to qualify test writers with basic testing theories,to make the test valid and reliable,to help improve educational reform and language teaching,to fully conform to the standards set by syllabus.