Nano-sized aluminum(Nano-Al)powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time.However,the near-detonation zone effects of reaction between Nano-Al wit...Nano-sized aluminum(Nano-Al)powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time.However,the near-detonation zone effects of reaction between Nano-Al with detonation products remain unclear.In this study,the overall reaction process of 170 nm Al with RDX explosive and its effect on detonation characteristics,detonation reaction zone,and the metal acceleration ability were comprehensively investigated through a variety of experiments such as the detonation velocity test,detonation pressure test,explosive/window interface velocity test and confined plate push test using high-resolution laser interferometry.Lithium fluoride(LiF),which has an inert behavior during the explosion,was used as a control to compare the contribution of the reaction of aluminum.A thermochemical approach that took into account the reactivity of aluminum and ensuing detonation products was adopted to calculate the additional energy release by afterburn.Combining the numerical simulations based on the calculated afterburn energy and experimental results,the parameters in the detonation equation of state describing the Nano-Al reaction characteristics were calibrated.This study found that when the 170 nm Al content is from 0%to 15%,every 5%increase of aluminum resulted in about a 1.3%decrease in detonation velocity.Manganin pressure gauge measurement showed no significant enhancement in detonation pressure.The detonation reaction time and reaction zone length of RDX/Al/wax/80/15/5 explosive is 64 ns and 0.47 mm,which is respectively 14%and 8%higher than that of RDX/wax/95/5 explosive(57 ns and 0.39 mm).Explosive/window interface velocity curves show that 170 nm Al mainly reacted with the RDX detonation products after the detonation front.For the recording time of about 10 ms throughout the plate push test duration,the maximum plate velocity and plate acceleration time accelerated by RDX/Al/wax/80/15/5 explosive is 12%and 2.9 ms higher than that of RDX/LiF/wax/80/15/5,respectively,indicating that the aluminum reaction energy significantly increased the metal acceleration time and ability of the explosive.Numerical simulations with JWLM explosive equation of state show that when the detonation products expanded to 2 times the initial volume,over 80%of the aluminum had reacted,implying very high reactivity.These results are significant in attaining a clear understanding of the reaction mechanism of Nano-Al in the development of aluminized explosives.展开更多
By using the Ti/Cu contact reaction couples, the dissolution behavior of Ti and Cu in the eutectic reaction process was investigated under different conditions. The results show that the formation of eutectic liquid p...By using the Ti/Cu contact reaction couples, the dissolution behavior of Ti and Cu in the eutectic reaction process was investigated under different conditions. The results show that the formation of eutectic liquid phase has a directional property, i.e. the eutectic liquid phase forms first at the Cu side and then spreads along the depth direction of Cu. The width of the eutectic liquid zone when Ti is placed on Cu is wider than that when Ti is placed under Cu. The shape of the upside liquid zone is wave-like. This phenomenon indicates that the formation process and spreading behavior in the upside are different from those in the underside, and there exists void effect in the Cu side of underside liquid zone, this will result in the delaying phenomenon of the contact reaction between Ti and Cu, and distinctly different shapes of the both liquid zones. The formation process of Ti/Cu eutectic liquid zone is similar to that of the traditional solid-state diffusion layer, and the relationship between the width of liquid zone and holding time obeys a square root law.展开更多
基金The authors would like to acknowledge National Natural Science Foundation of China(Grant No.11832006)Open Project of State Key Laboratory of Explosion Science and Technology in Beijing Institute of Technology(Grant No.KFJJ20-04 M)to provide fund for conducting experiments.
文摘Nano-sized aluminum(Nano-Al)powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time.However,the near-detonation zone effects of reaction between Nano-Al with detonation products remain unclear.In this study,the overall reaction process of 170 nm Al with RDX explosive and its effect on detonation characteristics,detonation reaction zone,and the metal acceleration ability were comprehensively investigated through a variety of experiments such as the detonation velocity test,detonation pressure test,explosive/window interface velocity test and confined plate push test using high-resolution laser interferometry.Lithium fluoride(LiF),which has an inert behavior during the explosion,was used as a control to compare the contribution of the reaction of aluminum.A thermochemical approach that took into account the reactivity of aluminum and ensuing detonation products was adopted to calculate the additional energy release by afterburn.Combining the numerical simulations based on the calculated afterburn energy and experimental results,the parameters in the detonation equation of state describing the Nano-Al reaction characteristics were calibrated.This study found that when the 170 nm Al content is from 0%to 15%,every 5%increase of aluminum resulted in about a 1.3%decrease in detonation velocity.Manganin pressure gauge measurement showed no significant enhancement in detonation pressure.The detonation reaction time and reaction zone length of RDX/Al/wax/80/15/5 explosive is 64 ns and 0.47 mm,which is respectively 14%and 8%higher than that of RDX/wax/95/5 explosive(57 ns and 0.39 mm).Explosive/window interface velocity curves show that 170 nm Al mainly reacted with the RDX detonation products after the detonation front.For the recording time of about 10 ms throughout the plate push test duration,the maximum plate velocity and plate acceleration time accelerated by RDX/Al/wax/80/15/5 explosive is 12%and 2.9 ms higher than that of RDX/LiF/wax/80/15/5,respectively,indicating that the aluminum reaction energy significantly increased the metal acceleration time and ability of the explosive.Numerical simulations with JWLM explosive equation of state show that when the detonation products expanded to 2 times the initial volume,over 80%of the aluminum had reacted,implying very high reactivity.These results are significant in attaining a clear understanding of the reaction mechanism of Nano-Al in the development of aluminized explosives.
基金Project(JKLSDT 02 01) supported by the Open Fund of the Jiangsu Key Laboratory of Ship Designing Technology
文摘By using the Ti/Cu contact reaction couples, the dissolution behavior of Ti and Cu in the eutectic reaction process was investigated under different conditions. The results show that the formation of eutectic liquid phase has a directional property, i.e. the eutectic liquid phase forms first at the Cu side and then spreads along the depth direction of Cu. The width of the eutectic liquid zone when Ti is placed on Cu is wider than that when Ti is placed under Cu. The shape of the upside liquid zone is wave-like. This phenomenon indicates that the formation process and spreading behavior in the upside are different from those in the underside, and there exists void effect in the Cu side of underside liquid zone, this will result in the delaying phenomenon of the contact reaction between Ti and Cu, and distinctly different shapes of the both liquid zones. The formation process of Ti/Cu eutectic liquid zone is similar to that of the traditional solid-state diffusion layer, and the relationship between the width of liquid zone and holding time obeys a square root law.
