Procedure for determining the number of thermal diffusion columns in square cascade for separation of Ne stable isotopes

The thermal diffusion column represents one method of separating stable isotopes.This method is advantageous for smallscale operations because of the simplicity of the apparatus and small inventory,especially in gas-phase operations.Consequently,it has attracted attention for its applicability in tritium and noble gas separation systems.In this study,the R cascade was used to design and determine the number of columns.A square cascade was adopted for the final design because of its flexibility,and calculations were performed to separate 20Ne and 22Ne isotopes.All the R cascades that enriched the Ne isotopes by more than 99%were investigated,the number of columns was determined,and the square cascade parameters were optimized using the specified columns.Additionally,a calculation code“RSQ_CASCADE”was developed.A unit separation factor of three was considered,and the number of studied stages ranged from 10 to 20.The results showed that the column separation power,relative total flow rate,and required number of columns were linearly related to the number of stages.The separation power and relative total flow decreased and the number of columns increased as the stage number increased.Therefore,a cascade of 85 columns is recommended to separate the stable Ne isotopes.These calculations yielded a 17-stage square cascade with five columns in each stage.By changing the stage cut,feed point,and cascade feed flow rate,the best parameters for the square cascade were determined according to the cascade and column separation powers.As the column separation power had a maximum value in cascade feed 50,it was selected for separating Ne isotopes.

Separation of W and Mo from their peroxoacids solutions by thermal decomposition

A separation method for W and Mo from peroxoacids solution by thermal decomposition wasstudied. Thermal decomposition of peroxotungstic acid and peroxomolybdic acid was investigated respectively. The results confirmed that peroxomolybdic acid showed a preferable stability compared with peroxotungstic acid. This thermal stability difference was the basic principle of theseparationof W and Mo. Experiments were performed to study the effects of temperature, stirring speed, free acid concentration and Mo concentration on the separation efficiency. The results indicated that peroxotungstic acid decomposed into tungstic acid（H2WO4） and precipitated selectively,while Mo was rejected in aqueous solution,realizing good separation of W and Mo. The separation factorof W and Moreached 112 under the studied conditions, which indicated that this method has potential for use in separating W and Mo.

Construction of Renewable Superhydrophobic Surfaces via Thermally Induced Phase Separation and Mechanical Peeling

We report a simple preparation method of a renewable superhydrophobic surface by thermally induced phase separation （TIPS） and mechanical peeling. Porous polyvinylidene fluoride （PVDF） membranes with hierarchical structures were prepared by a TIPS process under different cooling conditions, which were confirmed by scanning electron microscopy and mercury intrusion porosimetry. After peeling off the top layer, rough structures with hundreds of nanometers to several microns were obtained. A digital microscopy determines that the surface roughness of peeled PVDF membranes is much higher than that of the original PVDF membrane, which is important to obtain the superhydrophobicity. Water contact angle and sliding angle measurements demonstrate that the peeled membrane surfaces display super- hydrophobicity with a high contact angle （152°） and a low sliding angle （7.2°）. Moreover, the superhydrophobicity can be easily recovered for many times by a simple mechanical peeling, identical to the original superhydrophobicity. This simple preparation method is low cost, and suitable for large-scale industrialization, which may offer more opportunities for practical applications.

PREPARATION OF MICROPOROUS ULTRA HIGH MOLECULAR WEIGHT POLYETHYLENE (UHMWPE) BY THERMALLY INDUCED PHASE SEPARATION OF A UHMWPE/LIQUID PARAFFIN MIXTURE

Ultra-high molecular weight polyethylene (UHMWPE) with a microporous structure was prepared via thermally induced phase separation (TIPS).Liquid paraffin (LP) was used as a diluent in the preparation of microporous UHMWPE. Small angle laser light scattering (SALLS) and differential scanning calorimetry (DSC) were used to determine the phase separation temperatures,i.e.the cloud points and the dynamic crystallization temperatures,respectively.It was found that the cloudI points were coincident with the cryst...

Effect of Diluent on the Morphology and Performance of IPP Hollow Fiber Microporous Membrane via Thermally Induced Phase Separation

Isotactic polypropylene （iPP） hollow fiber microporous membranes were prepared using thermally induced phase separation （TIPS） method. Di-n-butyl phthalate （DBP）, dioctyl phthalate （DOP）, and the mixed solvent were used as diluents. The effect of α （DOP mass fraction in diluent） on the morphology and performance of the hollow fiber was investigated. With increasing α, the morphology of the resulting hollow fiber changes from typical cellular structure to mixed structure, and then to typical particulate structure. As a result, the permeability of the hollow fiber increases sharply, and the mechanical properties of the hollow fiber decrease obviously. It is suggested that the morphology and performances of iPP hollow fiber microporous membrane can be controlled via adjusting the compatibility between iPP and diluent.

PREPARATION OF HIGH DENSITY POLYETHYLENE/POLYETHYLENE-BLOCK-POLY(ETHYLENE GLYCOL)COPOLYMER BLEND POROUS MEMBRANES VIA THERMALLY INDUCED PHASE SEPARATION PROCESS AND THEIR PROPERTIES

High density polyethylene （HDPE）/polyethylene-block-poly（ethylene glycol） （PE-b-PEG） blend porous membranes were prepared via thermally induced phase separation （TIPS） process using diphenyl ether （DPE） as diluent. The phase diagrams of HDPE/PE-b-PEG/DPE systems were determined by optical microscopy and differential scanning calorimetry （DSC）. By varying the content of PE-b-PEG, the effects of PE-b-PEG copolymer on morphology and crystalline structure of membranes were studied by scanning electron microscopy （SEM） and wide angle X-ray diffraction （WAXD）. The chemical compositions of whole membranes and surface layers were characterized by elementary analysis, Fourier transform infrared spectroscopy-attenuated total reflection （FTIR-ATR） and X-ray photoelectron spectroscopy （XPS）. Water contact angle, static protein adsorption and water flux experiments were used to evaluate the hydrophilicity, antifouling and water permeation properties of the membranes. It was found that the addition of PE-b-PEG increased the pore size of the obtained blend membranes. In the investigated range of PE-b-PEG content, the PEG blocks could not aggregate into obviously separated domains in membrane matrix. More importantly, PE-b-PEG could not only be retained stably in the membrane matrix during membrane formation, but also enrich at the membrane surface layer. Such stability and surface enrichment of PE-b-PEG endowed the blend membranes with improved hydrophilicity, protein absorption resistance and water permeation properties, which would be substantially beneficial to HDPE membranes for water treatment application.

Effects of F127 on Properties of PVB/F127 Blend Hollow Fiber Membrane via Thermally Induced Phase Separation

Hydrophilic poly(vinyl butyral)(PVB) /Pluronic F127(F127) blend hollow fiber membranes were prepared via thermally induced phase separation(TIPS) ,and the effects of blend composition on the performance of hydrophilic PVB/F127 blend hollow fiber membrane were investigated.The addition of F127 to PVB/polyethylene glycol(PEG) system decreases the cloud point temperature,while the cloud point temperature increases slightly with the addition of F127 to 20%(by mass) PVB/F127/PEG200 system when the concentration of F127 is not higher than 5%(by mass) .Light scattering results show that the initial inter-phase periodic distance formed from the phase separation of 20%(by mass) PVB/F127/PEG200 system decreases with the addition of F127,so does the growth rate during cooling process.The blend hollow fiber membrane prepared at air-gap 5mm,of which the water permeability increases and the rejection changes little with the increase of F127 concentration.For the membrane prepared at zero air-gap,both water permeability and rejection of the PVB/F127 blend membrane are greater than those of PVB membrane,while the tensile strength changes little.Elementary analysis shows that most F127 in the polymer solution can firmly exist in the polymer matrix,increasing the hydrophilicity of the blend membrane prepared at air-gap of 5mm.

Fabrication of poly(vinylidene fluoride) membrane via thermally induced phase separation using ionic liquid as green diluent

Ionic liquid(IL),1-butyl-3-methylimidazolium hexafluorophosphate([BMIM]PF6)as a new and environmentally friendly diluent was introduced to prepare poly(vinylidene fluoride)(PVDF)membranes via thermally induced phase separation(TIPS).Phase diagram of PVDF/[BMIM]PF6 was measured.The effects of polymer concentration and quenching temperature on the morphologies,properties,and performances of the PVDF membranes were investigated.When the polymer concentration was 15 wt%,the pure water flux of the fabricated membrane was up to nearly 2000 L·m-2·h-1,along with adequate mechanical strength.With the increasing of PVDF concentration and quenching temperature,mean pore size and water permeability of the membrane decreased.SEM results showed that PVDF membranes manufactured by ionic liquid(BMIm PF6)presented spherulite structure.And the PVDF membranes were represented asβphase by XRD and FTIR characterization.It provides a new way to prepare PVDF membranes with piezoelectric properties.

Synergistic action of non-solvent induced phase separation in preparation of poly(vinyl butyral) hollow fiber membrane via thermally induced phase separation

A systematic study of air gap distance effects on the structure and properties of poly(vinyl butyral)hollow fiber membrane via thermally induced phase separation(TIPS)has been carried out.The results show that the hollow fiber membrane prepared at air gap zero has no skin layer; the pore size near the outer surface is larger than that near the inner surface; and the special pore channel-like structure near the outer surface is formed,which is quite different with the typical sponge-like structure caused by TIPS and the finger-like structure caused by non-solvent induced phase separation(NIPS),because of the synergistic action of non-solvent induced phase separation at air gap zero.The pore size gradually decreases from outer surface layer to the intermediate layer,but increases gradually from intermediate layer to the inner surface layer.With the increase of air gap distance,the pore size near the outer surface gets smaller and a dense skin layer is formed,and the pore size gradually increases from the outer surface layer to the inner surface layer.Water permeability of the hollow fiber membrane decreases with air gap distance,the water permeability decreases sharply from 45.50×10-7 to 4.52×10-7 m3/(m2·s·kPa)as air gap increases from 0 to 10 mm at take-up speed of 0.236 m/s,further decreases from 4.52×10-7 to 1.00×10-8 m3/(m2·s·kPa)as the air gap increases from 10 to 40 mm.Both the breaking strength and the elongation increase with the increase of air gap distance.The breaking strength increases from 2.25 MPa to 4.19 MPa and the elongation increases from 33.9% to 132.6% as air gap increases from 0 mm to 40 mm at take-up speed 0.236 m/s.

Fabrication of high temperature grating on thermal barrier coatings based on solute-solvent separation soft lithography

In this study, an etched-SiO-film grating fabrication technique based on solute-solvent separation soft lithography is developed. By using this new technique, high temperature grating with frequency of 600 lines/mm is successfully fabricated on the surface of thermal barrier coatings(TBCs). During the fabrication process, the microstructure and chemical compositions of ceramic coating before and after polishing is analyzed with a digital microscope and the energy dispersive X-ray spectroscope(EDS) in scanning electron microscope(SEM). And then the grating on TBCs is heated at the temperature ranging from 300℃ to 1000℃ for examining the high temperature resistance. In the practical application, the displacement and strain field around the crack on the ceramic surface are investigated with geometry phase analysis(GPA). The successful results verify that the etched-SiO-film grating has a good oxidation resistance and can be applied to high temperature deformation measurement of TBCs.

Effects of coagulation bath temperature on structure and performance of poly(vinyl butyral) hollow fiber membranes via thermally induced phase separation

Poly （vinyl butyral） （PVB） hollow fiber membranes were fabricated via thermally induced phase separation （TIPS）. The effects of coagulation bath temperature （CBT） on the structure and performance of membranes were investigated in detail. The morphologies of the membranes were studied by scanning electron microscopy （SEM）, the performances of water permeability, rejection, breaking strength and elongation were measured, respectively. The results indicate that all the membranes have the asymmetric morphology and the thickness of the skin layer decreases and the pore size of the outer layer increases with the increase of CBT. The permeability of membranes prepared at air gap 1.0 cm and take-up speed 0.253 m/s increases from 1.047×10-7 to 5.909×10-7 m3/（m2·s-kPa） with the CBT increasing from 20 ℃ to 40℃, and sharply increases to 35.226×10 7 m3/（m2.s.kPa）once the CBT arrives at 50 ℃. While the carbonic ink rejections have no significant decrease, totally exceed 98%, but that of acid-maleic acid copolymer greatly decreases with the increase of CBT. Both the breaking strength and elongation decrease with the increase of CBT.

Effect of Extractant and Cold-drawing on the Structure and Performance of HDPE Hollow Fiber Membranes Fabricated via Thermally Induced Phase Separation Method

Microporous polyolefin hollow fiber membranes were prepared from high density polyethylene （HDPE）-paraffin solution via thermally induced phase separation （TIPS） method. Effects of extraction and cold-drawing condition on membrane structure and performance were investigated.Five volatile solvents were used as extractant. Dimension of hollow fiber and gas permeation rate of membrane were measured. Mierostructure of membrane was examined by Scanning Electronic Microscope （SEM）. The results show that the membrane treated by pentane possesses a higher porosity, nitrogen permeability and lower shrinkage than those of membranes extracted by other three extractants. It is also found that the membrane stretched 133% shows the highest porosity and gas permeability in this study.

Numerical study of n-heptane/benzene separation by thermal diffusion column

In this article,numerical simulations are performed to investigate the performance of the thermal diffusion column for the separation of n-heptane/benzene mixture.The present work tried to optimize column by analyzing significant parameters such as feed flow rate,temperature and cut.In order to obtain the hydrodynamic and temperature and mass distribution inside thermal diffusion column,computational fluid dynamic(CFD) method is applied to solve the Navier-Stocks equations.Numerical simulations are conducted to study the main parameters in both stationary and time-dependent conditions.By using the separation work unit as a function of cut,the optimal cut for maximum SWU occurs within a limited range of 0.47-0.5 for feed rate between 0.5 and 4 g min^-1.Our findings reveal that the optimum feed rate in the range of optimum cut is about 1 g min^-1.In transient study,results show that the best cut for reaching to steady-state condition is θ=0.5.

Hydrogen-bonded organic framework modified separator for simultaneously enhancing the safety and electrochemical performance of Ni-rich lithium-ion battery

Nickel-rich layered oxide cathode(LiNi_(x)Co_(y)Mn_(1−x−y)O_(2),x>0.5,NCM)shows substantial potential for applications in longer-range electrical vehicles.However,the rapid capacity decay and serious safety concerns impede its practical viability.This work provides a hydrogen-bonded organic framework(HOF)modification strategy to simultaneously improve the electrochemical performance,thermal stability and incombustibility of separator.Melamine cyanurate(MCA),as a low-cost and reliable flame-retardant HOF,was implemented in the separator modification layer,which can prevent the battery short circuit even at a high temperature.In addition,the supermolecule properties of MCA provide unique physical and chemical microenvironment for regulating ion-transport behavior in electrolyte.The MCA coating layer enabled the nickel-rich layered oxide cathode with a high-capacity retention of 90.3%after 300 cycles at 1.0 C.Collectively,the usage of MCA in lithium-ion batteries(LIBs)affords a simple,low-cost and efficient strategy to improve the security and service life of nickel-rich layered cathodes.

Non-Isothermal Separation Process of Two-Phase Mixture Water/Ultra-Viscous Heavy Oil by Hydrocyclone

Environmental agencies do not allow effluents, from the petroleum productions, which contain oil concentrations that exceed the amounts permitted by the regulations. In recent time heavy oil operating petroleum industries are generating oil/water mixture by products, which are difficult to separate. Industrially, hydrocyclone is generally used to separate oil from an oil/water mixture. This is due to its high performance of separation, low cost of installation and maintenance. In the present work, therefore, the thermal fluid dynamics of water/ultra-viscous heavy oil separation process in a hydrocyclone has been studied. A steady state mathematical model which simulates the performance of a non-isothermal separation process is presented. The Eulerian-Eulerian approach for the interface of the phases involved (water/ultra-viscous heavy-oil) is used and the two-phase flow is considered as incompressible, viscous and turbulent. For carrying out numerical solutions of the governing equations the CFX11? commercial code was used. Results of the behavior of the two-fluid flow inside the hydrocyclone and separation efficiency are presented and analyzed. The role of the average temperature of the fluid, oil droplet diameter and the fluid mixture inlet velocity on the separation efficiency of the hydrocyclone are verified.

Fabrication of Poly(vinylidene fluoride) /Polysulfone Flat Blend Membranes via Thermally Induced Phase Separation Process for Water Treatment

Poly(vinylidene fluoride) /polysulfone(PVDF/PSF) flat blend membrane was prepared via thermally induced phase separation(TIPS) technique.The membrane formation mechanism and membrane structure were investigated and the effects of PSF/PVDF weight ratio on morphology,crystallinity,porosity,and mechanical properties of the membrane were discussed.The relationship between membrane structure and performances,such as pure water flux and the rejection of carbonic black,was also discussed.It was found that solid-liquid(S-L) phase separation occurred for the PVDF/PSF/diluent system.The addition of PSF influences structure and crystallinity of the membrane,which in turn influences mechanical properties and performances of the membrane.The results reveal that it is possible to obtain network structure via S-L phase separation by blending the polymer,which has a partial compatibility with PVDF.

Microstructures and properties of Al-45%Si alloy prepared by liquid-solid separation process and spray deposition

The microstructures and properties of A1-45%Si alloy prepared by liquid-solid separation （LSS） process and spray deposition （SD） were studied. The results show that the size, shape and distribution of the primary Si phase have different influence on the properties of alloys. Comparing with the Si particles with irregular shape, fine size and continuous distribution in SD alloy, the primary Si phase in LSS alloy is sphere-like, coarse and surrounded by the continuous AI matrix. The microstructure features of LSS alloy are beneficial to the higher thermal conductivity and lower thermal expansion coefficient at room temperature. The fine Si particle in SD alloy is advantageous to improving the mechanical properties. The increasing rates of thermal expansion coefficient with temperature are influenced by the distribution of the Si particles, where a lower rate is obtained in SD alloy with continuous Si particles. The agreement of thermal expansion coefficient with the model in LSS alloy differs from that in the SD alloy because of the different microstructure characteristics.

Microstructure and properties of SiC_p/Al electronic packaging shell produced by liquid-solid separation

The electronic packaging shell of high silicon carbide （54%SiC, volume fraction） aluminum-based composites was produced by liquid-solid separation technique. The characteristics of distribution and morphology of SiC as well as the shell’s fracture surface were examined by optical microscopy and scanning electron microscopy, and the thermo-physical and mechanical properties of the shell were also tested. The results show that Al matrix has a net-like structure while SiC is uniformly distributed in the Al matrix. The SiCp/Al composites have a low density of 2.93 g/cm^3, and its relative density is 98.7%. Thermal conductivity of the composites is 175 W/（·K）, coefficient of thermal expansion （CTE） is 10.3×10^-6 K-1 （25-400 ℃）, compressive strength is 496 MPa, bending strength is 404.5 MPa, and the main fracture mode is brittle fracture of SiC particles accompanied by ductile fracture of Al matrix.Its thermal conductivity is higher than that of Si/Al alloy, and its CTE matches with that of the chip material.

A polyethylene microsphere-coated separator with rapid thermal shutdown function for lithium-ion batteries

Thermal runaway is the main factor contributing to the unsafe behaviors of lithium-ion batteries(LIBs)in practical applications.The application of separators for the thermal shutdown has been proven as an effective approach to protecting LIBs from thermal runaway.In this work,we developed a thermal shutdown separator by coating a thin layer of low-density polyethylene microspheres(PM)onto a commercial porous polypropylene(PP)membrane and investigated the thermal response behaviors of the as-prepared PM/PP separator in LIBs.The structural and thermal analysis results revealed that the coated PM layer had a porous structure,which facilitated the occurrence of normal charge-discharge reactions at ambient temperature,although it could melt completely and fuse together within very short time periods:3 s at 110℃and 1 s at 120℃,to block off the pores of the PP substrate,thereby cutting off the ion transportation between the electrodes and interrupting the battery reaction.Consequently,the PM/PP separator exhibits very similar electrochemical performance to that of a conventional separator at ambient temperature.However,it performs a rapid thermal shutdown at an elevated temperature of^110℃,thus controlling the temperature rise and maintaining the cell in a safe status.Due to its synthetic simplicity and low cost,this separator shows promise for possible application in building safe LIBs.