Development of single pendulum impact scratch test for evaluating of thermally sprayed coatings

The adhesion of thermally sprayed coatings is an important subject for engineers applying thermal spray process . The single pendulum impact scratch test is the most popular method in the tribological investigation of modified surfaces of materials. In this paper, the adhesion of thermally sprayed coatings has been investigated using this test method. The key of evaluation for thermally sprayed coatings is the sheer strength of coatings obtained in the test. The results show that the test method is reproducible, reliable and easy to perform, and does not require expensive equipment . The procedure proposed in the test method for evaluating the adhesion of coatings is more reliable and realistic than others.

Microstructure studies of air-plasma-spray-deposited CoNiCrAlY coatings before and after thermal cyclic loading for high-temperature application

In the present study, bond-coats for thermal barrier coatings were deposited via air plasma spraying（APS） techniques onto Inconel 800 and Hastelloy C-276 alloy substrates. Scanning electron microscopy（SEM）, transmission electron microscopy（TEM）, X-ray diffraction（XRD）, and atomic force microscopy（AFM） were used to investigate the phases and microstructure of the as-sprayed, APS-deposited Co Ni Cr Al Y bond-coatings. The aim of this work was to study the suitability of the bond-coat materials for high temperature applications. Confirmation of nanoscale grains of the γ/γ′-phase was obtained by TEM, high-resolution TEM, and AFM. We concluded that these changes result from the plastic deformation of the bond-coat during the deposition, resulting in Co Ni Cr Al Y bond-coatings with excellent thermal cyclic resistance suitable for use in high-temperature applications. Cyclic oxidative stability was observed to also depend on the underlying metallic alloy substrate.

Influence of in-flight particle characteristics and substrate temperature on the formation mechanisms of hypereutectic Al-Si-Cu coatings prepared by supersonic atmospheric plasma spraying

Hypereutectic Al-Si-Cu coatings were prepared by supersonic atmospheric plasma spraying to enhance the surface performance of lightweight alloys.To find out optimum process conditions and achieve desirable coatings,this work focuses on the influence of three important parameters(in-flight particle temperature,impact velocity,and substrate temperature)on the collected splats morphology coatings microstructure and microhardness.Results show that appropriate combinations of temperature and velocity of in-flight particles cannot only completely melt hypereutectic Al-Si-Cu particles especially the primary Si phase,but also provide the particles with sufficient kinetic energy.Thus,the optimized coating consists of 98.6%of fully-melted region with nanosized coupled eutectic and 0.9%of porosity.Increasing the substrate deposition temperature promotes the transition from inhomogeneous banded microstructure to homogeneous equiaxed microstructure with a lower porosity level.The observations are further interpreted by a newly developed phase-change heat transfer model on quantitatively revealing the solidification and remelting behaviors of several splats deposited on substrate Besides,phase evolutions including the formation of supersaturatedα-Al matrix solid solution,growth of Si and Al_(2)Cu phases at different process conditions are elaborated.An ideal microstructure(low fractions of unmelted/partially-melted regions and defects)together with solid solution,grain refinement and second phase strengthening effects contributes to the enhanced microhardness of coating.This integrated study not only provides a framework for optimizing Al-Si based coatings via thermal spraying but also gives valuable insights into the formation mechanisms of this class of coating materials.

Corrosion Resistance of Ti_3Al/BN Abradable Seal Coating

Ti–Al mixed powder（Ti：Al = 3：1 in atomic ratio） and Ti3 Al intermetallic alloy powder mechanically clad hexagonal BN to fabricate Ti Al/BN and Ti3Al/BN composite powders. The corresponding porous abradable seal coatings（named as TAC-1 and TAC-2, respectively） were deposited using vacuum plasma spray（VPS） technology, and their corrosion behavior was studied via salt spray corrosion and electrochemical tests. Phase compositions and microstructures of these coatings before and after corrosion were characterized by X-ray diffraction（XRD） and scanning electron microscopy（SEM） facilitated with energy dispersive X-ray spectrometer（EDS）. The results showed that spontaneous passivation of TAC-1 and TAC-2 granted the coatings excellent corrosion resistance than that of commercial Al/BN coating. Additionally, TAC-2 exhibited higher corrosion potential（Ecorr） and breakdown potential（Ebp） but a lower corrosion current density（icorr） than TAC-1. A small quantity of the corrosion product（Al（OH）3and Al O） could be detected on the surface of TAC-1, while no corrosion product appeared in TAC-2. The non-uniform elements distribution in the metal matrix of TAC-1 resulted in localized corrosion and relatively poor corrosion resistance compared to TAC-2.