Investigation of three-pulse photon echo in thick crystal using finite-difference time-domain method

This paper investigates the phenomenon of three-pulse photon echo in thick rare-earth ions doped crystal whose thickness is far larger than 0.002 cm which is adopted in previous works.The influence of thickness on the three-pulse photon echo＇s amplitude and efficiency is analyzed with the Maxwell-Bloch equations solved by finite-difference timedomain method.We demonstrate that the amplitude of three-pulse echo will increase with the increasing of thickness and the optimum thickness to generate three-pulse photon echo is 0.3 cm for Tm^（3＋）：YAG when the attenuation of the input pulse is taken into account.Meanwhile,we find the expression 0.09 exp（α＇L）,which is previously employed to describe the relationship between echo＇s efficiency and thickness,should be modified as 1.3 · 0.09 exp（2.4 ·α＇L） with the propagation of echo considered.

Optical simulation of in-plane-switching blue phase liquid crystal display using the finite-difference time-domain method

The finite-difference time-domain method is used to simulate the optical characteristics of an in-plane switching blue phase liquid crystal display.Compared with the matrix optic methods and the refractive method,the finite-difference timedomain method,which is used to directly solve Maxwell＇s equations,can consider the lateral variation of the refractive index and obtain an accurate convergence effect.The simulation results show that e-rays and o-rays bend in different directions when the in-plane switching blue phase liquid crystal display is driven by the operating voltage.The finitedifference time-domain method should be used when the distribution of the liquid crystal in the liquid crystal display has a large lateral change.

An efficient locally one-dimensional finite-difference time-domain method based on the conformal scheme

An efficient conformal locally one-dimensional finite-difference time-domain（LOD-CFDTD） method is presented for solving two-dimensional（2D） electromagnetic（EM） scattering problems. The formulation for the 2D transverse-electric（TE） case is presented and its stability property and numerical dispersion relationship are theoretically investigated. It is shown that the introduction of irregular grids will not damage the numerical stability. Instead of the staircasing approximation, the conformal scheme is only employed to model the curve boundaries, whereas the standard Yee grids are used for the remaining regions. As the irregular grids account for a very small percentage of the total space grids, the conformal scheme has little effect on the numerical dispersion. Moreover, the proposed method, which requires fewer arithmetic operations than the alternating-direction-implicit（ADI） CFDTD method, leads to a further reduction of the CPU time. With the total-field/scattered-field（TF/SF） boundary and the perfectly matched layer（PML）, the radar cross section（RCS） of two2 D structures is calculated. The numerical examples verify the accuracy and efficiency of the proposed method.

IMPROVED LOCALLY CONFORMAL FINITE-DIFFERENCE TIME-DOMAIN METHOD FOR EDGE INCLINED SLOTS IN A FINITE WALL THICKNESS WAVEGUIDE

An Improved Locally Conformal Finite-Difference Time-Domain (ILC-FDTD) method is presented in this paper, which is used to analyze the edge inclined slots penetrating adjacent broadwalls of a finite wall thickness waveguide. ILC-FDTD not only removes tile instability of the original locally conformal FDTD algorithm, but also improves the computational accuracy by locally modifying magnetic field update equations and the virtual iterative electric fields accordlng to the complexity of tile slot fringe fields. The mutual coupling between two edge inclined slots can also be analyzed by ILC-FDTD effectively.

Three-dimensional numerical modeling of fullspace transient electromagnetic responses of water in goaf

The full-space transient electromagnetic response of water-filled goaves in coal mines were numerically modeled. Traditional numerical modeling methods cannot be used to simulate the underground full-space transient electromagnetic field. We used multiple transmitting loops instead of the traditional single transmitting loop to load the transmitting loop into Cartesian grids. We improved the method for calculating the z-component of the magnetic field based on the characteristics of full space. Then, we established the full- space 3D geoelectrical model using geological data for coalmines. In addition, the transient electromagnetic responses of water-filled goaves of variable shape at different locations were simulated by using the finite-difference time-domain （FDTD） method. Moreover, we evaluated the apparent resistivity results. The numerical modeling results suggested that the resistivity differences between the coal seam and its roof and floor greatly affect the distribution of apparent resistivity, resulting in nearly circular contours with the roadway head at the center. The actual distribution of apparent resistivity for different geoelectrical models of water in goaves was consistent with the models. However, when the goal water was located in one side, a false low-resistivity anomaly would appear on the other side owing to the full-space effect but the response was much weaker. Finally, the modeling results were subsequently confirmed by drilling, suggesting that the proposed method was effective.

3D finite-difference modeling algorithm and anomaly features of ZTEM

The Z-Axis tiPPer eiectromagnetic （ZTEM） technique is based on a frequency-domain airbome electromagnetic system that measures the natural magnetic field. A survey area was divided into several blocks by using the Maxwell＇s equations, and the magnetic components at the center of each edge of the grid cell are evaluated by applying the staggered-grid finite-difference method. The tipper and its divergence are derived to complete the 3D ZTEM forward modeling algorithm. A synthetic model is then used to compare the responses with those of 2D finite-element forward modeling to verify the accuracy of the algorithm. ZTEM offers high horizontal resolution to both simple and complex distributions of conductivity. This work is the theoretical foundation for the interpretation of ZTEM data and the study of 3D ZTEM inversion.

Numerical analysis of multicomponent responses of surface-hole transient electromagnetic method

We calculate the multicomponent responses of surface-hole transient electromagnetic method. The methods and models are unsuitable as geoelectric models of conductive surrounding rocks because they are based on regular local targets. We also propose a calculation and analysis scheme based on numerical simulations of the subsurface transient electromagnetic fields. In the modeling of the electromagnetic fields, the forward modeling simulations are performed by using the finite-difference time-domain method and the discrete image method, which combines the Gaver–Stehfest inverse Laplace transform with the Prony method to solve the initial electromagnetic fields. The precision in the iterative computations is ensured by using the transmission boundary conditions. For the response analysis, we customize geoelectric models consisting of near-borehole targets and conductive wall rocks and implement forward modeling simulations. The observed electric fields are converted into induced electromotive force responses using multicomponent observation devices. By comparing the transient electric fields and multicomponent responses under different conditions, we suggest that the multicomponent-induced electromotive force responses are related to the horizontal and vertical gradient variations of the transient electric field at different times. The characteristics of the response are determined by the varying the subsurface transient electromagnetic fields, i.e., diffusion, attenuation and distortion, under different conditions as well as the electromagnetic fields at the observation positions. The calculation and analysis scheme of the response consider the surrounding rocks and the anomalous field of the local targets. It therefore can account for the geological data better than conventional transient field response analysis of local targets.

Numerical modeling of the 2D time-domain transient electromagnetic secondary field of the line source of the current excitation

To effectively minimize the electromagnetic field response in the total field solution, we propose a numerical modeling method for the two-dimensional （2D） time- domain transient electromagnetic secondary field of the line source based on the DuFort- Frankel finite-difference method. In the proposed method, we included the treatment of the earth-air boundary conductivity, calculated the normalized partial derivative of the induced electromotive force （Emf）, and determined the forward time step. By extending upward the earth-air interface to the air grid nodes and the zero-value boundary conditions, not only we have a method that is more efficient but also simpler than the total field solution. We computed and analyzed the homogeneous half-space model and the fiat layered model with high precision--the maximum relative error is less than 0.01% between our method and the analytical method--and the solution speed is roughly three times faster than the total-field solution. Lastly, we used the model of a thin body embedded in a homogeneous half-space at different delay times to depict the downward and upward spreading characteristics of the induced eddy current, and the physical interaction processes between the electromagnetic field and the underground low-resistivity body.

THE STUDY ON MEASURING TECHNIQUE OF PARTIAL DISCHARGE IN GAS INSULATED SWITCHGEAR USING ULTRA HIGH FREQUENCY METHOD WITH EXTERNAL SENSORS

Objective In order to find early latent faults and prevent catastrophic failures, diagnosis of insulation condition by measuring technique of partial discharge(PD) in gas insulated switchgear (GIS) is applied in this paper, which is one of the most basic ways for diagnosis of insulation condition. Methods Ultra high frequency(UHF) PD detection method by using internal sensors has been proved efficient, because it may avoid the disturbance of corona, but the sensor installation of this method will be limited by the structure and operation condition of GIS. There are some of electromagnetic (E-M) waves leak from the place of insulation spacer, therefore, the external sensors UHF measuring PD technique is applied, which isn't limited by the operation condition of GIS. Results This paper analyzes propagated electromagnetic (E-M) waves of partial discharge pulse excited by using the finite-difference time-domain (FDTD) method. The signal collected at the outer point is more complex than that of the inner point, and the signals' amplitude of outer is about half of the inner, because it propagates through spacer and insulation slot. Set up UHF PD measuring system. The typical PD in 252kV GIS bus bar was measured using PD detection UHF technique with external sensors. Finally, compare the results of UHF measuring technique using external sensors with the results of FDTD method simulation and the traditional IEC60270 method detection. Conclusion The results of experiment shows that the UHF technique can realize the diagnosis of insulation condition, the results of FDTD method simulation and the result UHF method detection can demonstrate each other, which gives references to further researches and application for UHF PD measuring technique.

A Revised Piecewise Linear Recursive Convolution FDTD Method for Magnetized Plasmas

The piecewise linear recursive convolution （PLRC） finite-different time-domain （FDTD） method improves accuracy over the original recursive convolution （RC） FDTD approach and current density convolution （JEC） but retains their advantages in speed and efficiency. This paper describes a revised piecewise linear recursive convolution PLRC-FDTD formulation for magnetized plasma which incorporates both anisotropy and frequency dispersion at the same time, enabling the transient analysis of magnetized plasma media. The technique is illustrated by numerical simulations of the reflection and transmission coefficients through a magnetized plasma layer. The results show that the revised PLRC-FDTD method has improved the accuracy over the original RC FDTD method and JEC FDTD method.

Theoretical Proof of Unconditional Stability of the 3-D ADI-FDTD Method

In order to eliminate Courant-Friedrich-Levy(CFL) condition restraint and improvecomputational efficiency,a new finite-difference time-domain(FDTD)method based on the alternating-direction implicit(ADI) technique is introduced recently.In this paper,a theoretical proof of the stabilityof the three-dimensional(3-D)ADI-FDTD method is presented.It is shown that the 3-D ADI-FDTDmethod is unconditionally stable and free from the CFL condition restraint.

Analysis of Complex Electromagnetic Structures by Hybrid FDTD/WCIP Method

This paper proposes a hybrid full-wave analysis using Finite-Difference Time-Domain (FDTD) and Wave Concept Iterative Process (WCIP) methods, developed to analyze locally arbitrarily shaped microwave structures and Multilayer Planar structure. Using the equivalence principle, the original problem can be decomposed into two sub regions and solve each sub region separately. An interpolation scheme is proposed for communicating between the FDTD fields and WCIP wave, which will not require the effort of fitting the WCIP mesh to the FDTD cells in the interface region. This method is applied to calculate the scattering parameters of arbitrary (3-D) microwave structures. Applying FDTD to 3D discontinuity and WCIP to the remaining region preserves the advantages of both WCIP flexibility and FDTD efficiency. A comparison of the results with the FDTD staircasing data verifies the accuracy of the proposed method.

Splitting Finite Difference Methods on Staggered Grids for the Three-Dimensional Time-Dependent Maxwell Equations

In this paper,we study splitting numerical methods for the three-dimensional Maxwell equations in the time domain.We propose a new kind of splitting finitedifference time-domain schemes on a staggered grid,which consists of only two stages for each time step.It is proved by the energy method that the splitting scheme is unconditionally stable and convergent for problems with perfectly conducting boundary conditions.Both numerical dispersion analysis and numerical experiments are also presented to illustrate the efficiency of the proposed schemes.

Borehole-GPR numerical simulation of full wave field based on convolutional perfect matched layer boundary

The absorbing boundary is the key in numerical simulation of borehole radar.Perfect match layer(PML) was chosen as the absorbing boundary in numerical simulation of GPR.But CPML(convolutional perfect match layer) approach that we have chosen has the advantage of being media independent.Beginning with the Maxwell equations in a two-dimensional structure,numerical formulas of finite-difference time-domain(FDTD) method with CPML boundary condition for transverse electric(TE) or transverse magnetic(TM) wave are presented in details.Also,there are three models for borehole-GPR simulation.By analyzing the simulation results,the features of targets in GPR are obtained,which can provide a better interpretation of real radar data.The results show that CPML is well suited for the simulation of borehole-GPR.

A Study of Properties of the Photonic Band Gap of Unmagnetized Plasma Photonic Crystal

In this study, the propagation of electromagnetic waves in one-dimensional plasma photonic crystals （PPCs）, namely, superlattice structures consisting alternately of a homogeneous unmagnetized plasma and dielectric material, is simulated numerically using the finite-difference time-domain （FDTD） algorithm. A perfectly matched layer （PML） absorbing technique is used in this simulation. The reflection and transmission coefficients of electromagnetic （EM） waves through PPCs are calculated. The characteristics of the photonic band gap （PBG） are discussed in terms of plasma density, dielectric constant ratios, number of periods, and introduced layer defect. These may provide some useful information for designing plasma photonic crystal devices.

Propagation characteristics of oblique incidence terahertz wave through non-uniform plasma

The propagation characteristics of oblique incidence terahertz(THz) waves through non-uniform plasma are investigated by the shift-operator finite-difference time-domain(SO-FDTD) method combined with the phase matching condition.The electron density distribution of the non-uniform plasma is assumed to be in a Gaussian profile. Validation of the present method is performed by comparing the results with those obtained by an analytical method for a homogeneous plasma slab.Then the effects of parameters of THz wave and plasma layer on the propagation properties are analyzed. It is found that the transmission coefficients greatly depend on the incident angle as well as on the thickness of the plasma, while the polarization of the incident wave has little influence on the propagation process in the range of frequency considered in this paper. The results confirm that the THz wave can pass through the plasma sheath effectively under certain conditions,which makes it a potential candidate to overcome the ionization blackout problem.

A numerical simulation of surface wave excitation in a rectangular planar-type plasma source

The principle of surface wave plasma discharge in a rectangular cavity is introduced simply based on surface plasmon polariton theory. The distribution of surface-wave electric field at the interface of the plasma-dielectric slab is investigated by using the three-dimensional finite-difference time-domain method （3D-FDTD） with different slotantenna structures. And the experimental image of discharge with a novel slot antenna array and the simulation of the electric field with this slot antenna array are both displayed. Combined with the distribution of surface wave excitation and experimental results, the numerical simulation performed by using 3D-FDTD is shown to be a useful tool in the computer-aided antenna design for large area planar-type surface-wave plasma sources.

A subwavelength metal-grating assisted sensor of Kretschmann style for investigating the sample with high refractive index

In this paper, a subwavelength metal-grating assisted sensor of Kretschmann style that is capable of detecting the sample with a refractive index higher than that of the substrate is proposed. The sensor configuration is similar to the traditional Kretschmann structure, but the metal film is pattered into a grating. As a TM-polarized laser beam impinges from the substrate, a resonant dip point in reflectance curve is produced at a certain incident angle. Our studies indicate that the sensing sensitivity and resolution are affected by the grating＇s gap and period, and after these parameters havelaeen optimized, a sensing sensitivity of 51.484°/RIU is obtained with a slightly changing resolution.

Rear-surface light intensification caused by a Hertzian-conical crack in 355-nm silica optics

Theoretical studies show that a Hertzian-conical crack can be considered to be composed of double cone faces for simplicity. In the present study, the three-dimensional finite-difference time-domain method is employed to quantify the electric-field distribution within the subsurface in the presence of such a defect under normal incidence irradiation. Both impurities （inside the crack） and the chemical etching have been investigated. The results show that the maximum electric field amplitude │E│max is 9.57374 V/m when the relative dielectric constant of transparent impurity equals 8.5. And the near-field modulation will be improved if the crack is filled with the remainder polishing powders or water vapor/drops. Meanwhile, the laser-induced initial damage moves to the glass-air surface. In the etched section, the magnitude of intensification is strongly dependent on the inclination angle θ. There will be a highest modulation when θ is around π/6, and the maximum value of IEImax is 18.57314 V/m. When θ ranges from π/θ to π/4, the light intensity enhancement factor can easily be larger than 100, and the modulation follows a decreasing trend. On the other hand, the modulation curves become smooth when θ〉π/4 or θ 〈 π/8.

A Novel Electromagnetic Bandgap Structure for Filter

Electromagnetic bandgap （EBG） materials are periodic structures capable of prohibiting the propagation of electromagnetic waves within a certain band of frequencies. This characteristic of EBG has wide application. The structures to be studied here are mainly planar EBG materials of two dimensions, which are periodic arrays of holes etched in the ground plane of a conventional microstrip line. EBG structures are calculated with finite-difference time-domain （FDTD） method in this paper. Technique of the perfectly matched layer is used for the absorption of electromagnetic waves in FDTD. The FDTD method is programmed with the blend of C++ and Matlab languages, which makes the program both simple and fast computing. A kind of new EBG structure is brought out through a lot of experiments and analyses. A filter with wide stop-band and another filter with two stop-bands are designed.