Simulation of Wave Impact on Three-Dimensional Horizontal Plate Based on SPH Method

An improved three-dimensional incompressible smooth particle hydrodynamics(ISPH)model is developed to simulate the impact of regular wave on a horizontal plate.The improvement is the employment of a corrective function to enhance angular momentum conservation in a particle-based calculation.And a new estimation method is proposed to predict the pressure on the horizontal plate.Then,the model simulates the variation characteristics of impact pressures generated by regular wave slamming.The main features of velocity field and pressure field near the plate are presented.The present numerical model can be used to study wave impact load on the horizontal plate.

Three-Dimensional Scattering of an Incident Plane Shear Horizontal Guided Wave by a Partly through-Thickness Hole in a Plate

We investigate the three-dimensional （3D） scattering problem of an incident plane shear horizontal wave by a partly through-thickness hole in an isotropic plate, in which the Lamb wave modes are also included due to the mode conversions by the scattering obstacle in the 3D problem. An analytical model is presented such that the wave fields are expanded in all of propagating and evanescent SH modes and Lamb modes, and the scattered far-fields of three fundamental guided wave modes are analyzed numerically for different sizes of the holes and frequencies. The numerical results are verified by comparing with those obtained by using the approximate Poisson/Mindlin plate model for small hole radius and low frequency. It is also found that the scattering patterns are different from those of the SO wave incidence. Our work is useful for quantitative evaluation of the plate-like structure by ultrasonic guided waves.

Uplift Pressure of Waves on A Horizontal Plate

Uplift pressures of waves acting on horizontal plates are the important basis for design of maritime hollow-trussed structures. In this paper, an experimental study on the uplift pressures of waves on a horizontal plate is conducted by use of a series of model tests. Detailed analysis has been given to the formation mechanism of uplift pressures of waves. It is considered that the impact pressure intensity is mainly affected by geometrical factors (tangential angle of waves), dynamic factors (wave height, wave velocity, etc.) and air cushion. Based on the test results, an equation for calculation of the maximum uplift pressure intensity of waves on a plate is presented. A large quantity of test data shows good agreement of the present equation with the test results.

Effect of buried plates on scour profiles downstream of hydraulic jump in open channels with horizontal and reverse bed slopes

Local scour downstream of sluice gates in erosive beds is one of the main concerns of hydraulic engineers because it can cause considerable damage to structures.Many researchers have conducted various studies to predict the maximum depth and length of scour holes and to develop new methods to control this phenomenon.In the methods that have recently been examined,embedded buried plates are used to control the scour in the erosive beds.In this study,using a physical model,the effect of buried plates in erosive beds on the depth of scour downstream of a hydraulic jump was studied.Several experiments were performed in which plates were buried at 50° and 90° angles at different distances from the apron in open channels with horizontal and reverse bed slopes.The results of experiments in which the scour profiles were drawn in dimensionless forms show that the angle and position of the plates are important to controlling and reducing scour depth.In fact,by reducing the angle of buried plates,the maximum depth of scour is also reduced.Also,comparison of the results of a single buried plate and double buried plates shows that using two buried plates at the distances of 30 and 45 cm from the non-erodible bed is more effective in reducing the scour depth.The best distances of the buried plates with angles of 90° and 50° from the non-erodible bed are 45 cm and 30 cm,respectively,in the condition with a single buried plate.

MPS Method for Interaction Between Solitary Waves and Submerged Horizontal Plate

The interaction between structure and wave is a typical phenomenon in naval architecture and ocean engineering.In this paper,numerical simulation is carried out to study the interaction between a two-dimensional submerged,fixed,horizontal rigid plate and solitary wave with our in-house meshless particle CFD solver MLParticle-SJTU.First,the in-house CFD solver is verified by experimental results conducted at the State Key Laboratory of Coastal and Offshore Engineering,Dalian University of Technology.During the verification,the plate is submerged under water and the solitary wave with a given amplitude is generated by a piston-type wave maker.Free surface elevation of the wave and the pressure impacting on the plate is recorded and compared with experimental data respectively.The predicted pressure and surface elevation agree well with the experimental results.Then in order to further investigate factors affecting wave-structure interaction,wave height,submerged depth and plate length are analyzed.

THREE-DIMENSIONAL ANALYSIS OF FUNCTIONALLY GRADED PLATE BASED ON THE HAAR WAVELET METHOD

A three-dimensional analysis of a simply-supported functionally graded rectangular plate with an arbitrary distribution of material properties is made using a simple and effective method based on the Haar wavelet. With good features in treating singularities, Haar series solution converges rapidly for arbitrary distributions, especially for the case where the material properties change rapidly in some regions. Through numerical examples the influences of the ratio of material constants on the top and bottom surfaces and different material gradient distributions on the structural response of the plate to mechanical stimuli are studied.

Hydroelastic Response of VLFS with An Attached Submerged Horizontal Solid/Porous Plate Under Wave Action

The hydroelastic responses of a submerged horizontal solid/porous plate attached at the front of a very large rectangular floating structure(VLFS)under wave action has been investigated in the context of linear water wave theory.Darcy’s law is adopted to represent energy dissipation in pores.It is assumed that the porous plates are made of material with very fine pores so that the normal velocity across the perforated porous is linearly associated with the pressure drop.In the analytic method,the eigenfunction expansion-matching method(EEMM)for multiple domains is applied to solve the hydrodynamic problem and the elastic equation of motion is solved by the modal expansion method.The performance of the proposed submerged horizontal solid/porous plate can be significantly enhanced by selecting optimal design parameters,such as plate length,horizontal position,submerged depth and porosity.It is concluded that good damping effect can be achieved through installation of solid and porous plate.Porous plate has better damping effect at low frequencies,while solid plate has better damping effect at high frequencies.The optimal ratio of plate length to water depth is 0.25-0.375,and the optimal ratio of submerged depth to water depth is 0.09-0.181.

Reconstruction of heat flux profile on the HL-2A divertor plate with a three-dimensional analysis model

A three-dimensional analysis model based on the finite element method （FEM） is developed, which can derive the evolution and distribution characteristics of heat flux deposited on the divertor plate from the surface temperature measured by infrared thermography diagnostics. The numerical simulations of surface heating due to localized power bursts and the power deposition calculations demonstrate that this analysis can provide accurate results and useful information about localized hot spots compared with the normal one- and two-dimensional calculations. In this paper, the details of this three- dimensional analysis are presented, and some results in ohmic heating and electron cyclotron resonant heating （ECRH） discharge on HL-2A are given.

Excitation and Detection of Shear Horizontal Waves with Electromagnetic Acoustic Transducers for Nondestructive Testing of Plates

The fundamental shear horizontal（SH0） wave has several unique features that are attractive for long-range nondestructive testing（NDT）. By a careful design of the geometric configuration, electromagnetic acoustic transducers（EMATs） have the capability to generate a wide range of guided wave modes, such as Lamb waves and shear-horizontal（SH） waves in plates. However, the performance of EMATs is influenced by their parameters. To evaluate the performance of periodic permanent magnet（PPM） EMATs, a distributed-line-source model is developed to calculate the angular acoustic field cross-section in the far-field. Numerical analysis is conducted to investigate the performance of such EMATs with different geometric parameters, such as period and number of magnet arrays, and inner and outer coil widths. Such parameters have a great influence on the directivity of the generated SH0 waves that arises mainly in the amplitude and width of both main and side lobes. According to the numerical analysis, these parameters are optimized to obtain better directivity. Optimized PPM EMATs are designed and used for NDT of strip plates. Experimental results show that the lateral boundary of the strip plate has no perceivable influence on SHO-wave propagation, thus validating their used in NDT. The proposed model predicts the radiation pattern ofPPM EMATs, and can be used for their parameter optimization.

Hydroelastic Analysis of a Very Large Floating Structure Edged with a Pair of Submerged Horizontal Plates

This paper is concerned with the hydroelastic problem of a very large pontoon-type floating structure(VLFS) edged with a pair of submerged horizontal plates, which is a combination of perforated and non-perforated plates attached to the for-end and back-end of the VLFS. For the hydroelastic analysis, the fluid is assumed to be ideal and its motion is irrotational so that a velocity potential exists. The VLFS is modeled as an elastic plate according to the classical thin plate theory. The fluid-structure interaction problem is separated into conventional hydrodynamics and structure dynamics by using modal expansion method in the frequency-domain. It involves, firstly, the deflection of the VLFS, which is expressed by a superposition of modal functions and corresponding modal amplitudes. Then the boundary element method is used to solve the integral equations of diffraction and radiation on the body surface for the velocity potential, whereas the vibration equation is solved by the Galerkin's method for modal amplitudes, and then the deflection is obtained by the sum of multiplying modal functions with modal amplitudes. This study examines the effects of the width and location of the non-perforated horizontal plates on the hydroelastic response of the VLFS, then the performance of perforated plates is investigated to reduce the motion near the fore-end of the VLFS. Considering the advantages and disadvantages of submerged plates without and with cylindrical holes, we propose a simple anti-motion device, which is a combination of a pair of perforated and non-perforated plates attached to the for-end and back-end of the VLFS. The effectiveness of this device in reducing the deformation and bending moment of the VLFS has been confirmed, and is compared with the results in cases without and with the submerged horizontal plates by the analysis in this paper.

Hot compressive deformation of eutectic Al-17at%Cu alloy on the interface of the Cu-Al composite plate produced by horizontal continuous casting

On the interface of the Cu-Al composite plate from horizontal continuous casting,the eutectic microstructure layer thickness ac-counts for more than 90%of the total interface thickness,and the deformation in rolling forming plays an important role in the quality of the composite plate.The eutectic microstructure material on the interface of the Cu-Al composite plate was prepared by changing the cooling rate of ingot solidification and the deformation in hot compression was investigated.The results show that when the deformation temperature is over 300℃,the softening effect of dynamic recrystallization ofα-Al is greater than the hardening effect,and uniform plastic deformation of eutectic microstructure is caused.The constitutive equation of flow stress in the eutectic microstructure layer was established by Arrhenius hy-perbolic-sine mathematics model,providing a reliable theoretical basis for the deformation of the Cu-Al composite plate.

Numerical Analysis of the Flow Field in a Sloshing Tank with a Horizontal Perforated Plate

Liquid sloshing is a type of free surface flow inside a partially filled water tank.Sloshing exerts a significant effect on the safety of liquid transport systems;in particular,it may cause large hydrodynamic loads when the frequency of the tank motion is close to the natural frequency of the tank.Perforated plates have recently been used to suppress the violent movement of liquids in a sloshing tank at resonant conditions.In this study,a numerical model based on OpenF OAM(Open Source Field Operation and Manipulation),an open source computed fluid dynamic code,is used to investigate resonant sloshing in a swaying tank with a submerged horizontal perforated plate.The numerical results of the free surface elevations are first verified using experimental data,and then the flow characteristics around the perforated plate and the fluid velocity distribution in the entire tank are examined using numerical examples.The results clearly show differences in sloshing motions under first-order and third-order resonant frequencies.This study provides a better understanding of the energy dissipation mechanism of a horizontal perforated plate in a swaying tank.

Three-dimensional elasticity solutions for bending of generally supported thick functionally graded plates

Three-dimensional elasticity solutions for static bending of thick functionally graded plates are presented using a hybrid semi-analytical approach-the state-space based differential quadrature method （SSDQM）. The plate is generally supported at four edges for which the two-way differential quadrature method is used to solve the in-plane variations of the stress and displacement fields numerically. An approximate laminate model （ALM） is exploited to reduce the inhomogeneous plate into a multi-layered laminate, thus applying the state space method to solve analytically in the thickness direction. Both the convergence properties of SSDQM and ALM are examined. The SSDQM is validated by comparing the numerical results with the exact solutions reported in the literature. As an example, the Mori-Tanaka model is used to predict the effective bulk and shear moduli. Effects of gradient index and aspect ratios on the bending behavior of functionally graded thick plates are investigated.

NONLINEAR THREE-DIMENSIONAL ANALYSIS OF COMPOSITELAMINATED PLATES

In this paper. an analytic method is. presented. for the research of nonlinear Three-dimensional problems of composite laminated plates. The perturbation method and the variational principle are used to satisfy the basic differential equations and the boundary conditions of the three-dimensional theory of elasticity. The nonlinear three-dimensional problems are studied .for composite anisotropic circular laminas and laminates subjected to transverse loading. The perturbation series solutions of high accuracy are obtained. A large number of results show that transverse normal stress and transverse shear stresses are very important in the nonlinear three-dimensional analysis of laminated plates.

Analytical and Experimental Studies on Wave Scattering by a Horizontal Perforated Plate at the Still Water Level

This research investigates water-wave scattering via a horizontal perforated plate fixed at the still water level through analytical studies and physical model tests.The velocity potential decomposition method is combined with an efficient iterative algorithm to develop an analytical solution in which the quadratic pressure drop condition is imposed on the horizontal perforated plate.The analytical results are in good agreement with the results of an independently developed iterative boundary element method(BEM)solution.Experimental tests are carried out in a wave flume to measure the reflection coefficient and transmission coefficient of the horizontal perforated plate,and the analytical results agree reasonably well with the experimental data.The influence of various structural parameters of the horizontal perforated plate on the hydrodynamic parameters of reflection coefficient,transmission coefficient,energy-loss coefficient,and wave force are analyzed on the basis of the analytical solution.Useful results for the practical engineering application of horizontal perforated plates are also presented.

Similarity Solutions for Laminar Boundary Layer Flow of Darcian Fluid over Horizontal Plate with a Convective Boundary Condition

This paper considers the problem of hydrodynamics and thermal boundary layers of Darcy flow over horizontal surface embedded in a porous medium. The solutions of such problems for the cases of uniform surface temperature and variable surface temperature have been studied and analysed in many papers. This paper, however, attempts to find similarity solutions for the Darcy flow problem with a convective boundary condition at the plate surface. It is found that the solution is possible when the heat transfer coefficient is proportional to x–2/3. The numerical solutions thus obtained are analyzed for a range of values of the parameter characterizing the hot fluid convection process. Analytical expressions are provided for local surface heat flux and total surface heat transfer rate while the flow variables are discussed graphically.

Similarity Solutions of Unsteady Mixed Convective Boundary Layer Flow of Viscous Incompressible Fluid along Isothermal Horizontal Plate

Unsteady mixed convective boundary layer flow of viscous incompressible fluid along isothermal horizontal plate is analyzed through Similarity Solutions. The governing partial differential equations are transformed into ordinary differential equations using the similarity transformation and solved numerically along with shooting technique. The flow field for the fluid velocity, temperature and concentration at the plate surface are significantly influenced by the governing parameters such as unsteadiness parameter, permeability parameter, Prandtl number, Schmidt number and the other driving parameters. The results show that both fluid velocity and temperature decrease but no significant effect on concentration for the increasing values of Prandtl number. It is also exposed that velocity and concentration is higher at lower Schmidt number for low Prandtl fluid. Finally, the dependency of the Skin-friction co-efficient, Nusselt number and Sherwood number, which are of physical interest, are also illustrated in tabular form for the governing parameters.

Stream Surface Strip Element Method and Simulation of Three-Dimensional Deformation of Continuous Hot Rolled Strip

A new method,the stream surface strip element method,for simulating the three-dimensional deformation of plate and strip rolling process was proposed.The rolling deformation zone was divided into a number of stream surface(curved surface)strip elements along metal flow traces,and the stream surface strip elements were mapped into the corresponding plane strip elements for analysis and computation.The longitudinal distributions of the lateral displacement and the altitudinal displacement of metal were respectively constructed to be a quartic curve and a quadratic curve,of which the lateral distributions were expressed as the third-power spline function,and the altitudinal distributions were fitted in the quadratic curve.From the flow theory of plastic mechanics,the mathematical models of the three-dimensional deformations and stresses of the deformation zone were constructed.Compared with the streamline strip element method proposed by the first author of this paper,the stream surface strip element method takes into account the uneven distributions of stresses and deformations along altitudinal direction,and realizes the precise three-dimensional analysis and computation.The simulation example of continuous hot rolled strip indicates that the method and the model accord with facts and provide a new reliable engineering-computation method for the three-dimensional mechanics simulation of plate and strip rolling process.

Research and application on three-dimensional seismic and vibration isolation for building

This paper presents the study of a three-dimensional(3D) isolation system.Firstly,the authors investigated the effects of an innovative 3D isolator,which was composed of a connecting plate,a rubber pad for vibration isolation in the vertical direction and a horizontal rubber bearing for seismic isolation in both horizontal directions.Secondly,the authors designed such a vibration isolation system and installed it underneath two specific residential buildings which were built directly over an existing subway communication hub platform in Beijing.These buildings required good performance vibration and seismic isolation system to reduce the impact from the running of nearby subway trains.Finally,in situ tests were conducted for both the isolated and the non-isolated buildings for the purpose of comparison.The test results showed that the maximum acceleration response level of the isolated superstructure is reduced by 10% as compared to that of the platform.The maximum attenuation of vibration reaches up to 25 dB.The 3D system explored in this paper is very effective in control and suppression of building vibration induced by earthquakes or running of trains.

Progress and prospects of horizontal well fracturing technology for shale oil and gas reservoirs

By systematically summarizing horizontal well fracturing technology abroad for shale oil and gas reservoirs since the “13th Five-Year Plan”, this article elaborates new horizontal well fracturing features in 3D development of stacked shale reservoirs, small well spacing and dense well pattern, horizontal well re-fracturing, fracturing parameters optimization and cost control. In light of requirements on horizontal well fracturing technology in China, we have summarized the technological progress in simulation of multi-fracture propagation, horizontal well frac-design, electric-drive fracturing equipment, soluble tools and low-cost downhole materials and factory-like operation. On this basis, combined with the demand analysis of horizontal well fracturing technology in the “14th Five-Year Plan” for unconventional shale oil and gas, we suggest strengthening the research and development in the following 7 aspects:(1) geology-engineering integration;(2) basic theory and design optimization of fracturing for shale oil and gas reservoirs;(3) development of high-power electric-drive fracturing equipment;(4) fracturing tool and supporting equipment for long horizontal section;(5) horizontal well flexible-sidetracking drilling technology for tapping remaining oil;(6) post-frac workover technology for long horizontal well;(7) intelligent fracturing technology.