Through-silicon-via crosstalk model and optimization design for three-dimensional integrated circuits

Through-silicon-via （TSV） to TSV crosstalk noise is one of the key factors affecting the signal integrity of three- dimensional integrated circuits （3D ICs）. Based on the frequency dependent equivalent electrical parameters for the TSV channel, an analytical crosstalk noise model is established to capture the TSV induced crosstalk noise. The impact of various design parameters including insulation dielectric, via pitch, via height, silicon conductivity, and terminal impedance on the crosstalk noise is analyzed with the proposed model. Two approaches are proposed to alleviate the TSV noise, namely, driver sizing and via shielding, and the SPICE results show 241 rnV and 379 mV reductions in the peak noise voltage, respectively.

The Use of Three-Dimensional Integrated Design System in Smart Substation Design

The traditional power design, construction, has been able to meet the requirements, but it has not been established engineering data database support and the correlation between the data is poor, due to inadequate coordination among design professionals, design easily lead to mistakes, field problems, and design results failed in all aspects of the project to be fully utilized. With the technology of three-dimensional integrated design system penetrates in all walks of life, the introduction of three-dimensional integrated design system substation design solutions and the application of common devices of State Grid Corporation in recent years, which provide technical conditions for the application of virtual reality technology in substation design. According to its own characteristics of substation project, we now propose prospect on virtual reality technology in substation design application.

Oxygen tension modulates cell function in an in vitro three-dimensional glioblastoma tumor model

Hypoxia is a typical feature of the tumor microenvironment,one of the most critical factors affecting cell behavior and tumor progression.However,the lack of tumor models able to precisely emulate natural brain tumor tissue has impeded the study of the effects of hypoxia on the progression and growth of tumor cells.This study reports a three-dimensional(3D)brain tumor model obtained by encapsulating U87MG(U87)cells in a hydrogel containing type I collagen.It also documents the effect of various oxygen concentrations(1%,7%,and 21%)in the culture environment on U87 cell morphology,proliferation,viability,cell cycle,apoptosis rate,and migration.Finally,it compares two-dimensional(2D)and 3D cultures.For comparison purposes,cells cultured in flat culture dishes were used as the control(2D model).Cells cultured in the 3D model proliferated more slowly but had a higher apoptosis rate and proportion of cells in the resting phase(G0 phase)/gap I phase(G1 phase)than those cultured in the 2D model.Besides,the two models yielded significantly different cell morphologies.Finally,hypoxia(e.g.,1%O2)affected cell morphology,slowed cell growth,reduced cell viability,and increased the apoptosis rate in the 3D model.These results indicate that the constructed 3D model is effective for investigating the effects of biological and chemical factors on cell morphology and function,and can be more representative of the tumor microenvironment than 2D culture systems.The developed 3D glioblastoma tumor model is equally applicable to other studies in pharmacology and pathology.

Optimal synthesis of heat-integrated distillation configurations using the two-column superstructure

In the realm of the synthesis of heat-integrated distillation configurations,the conventional approach for exploring more heat integration possibilities typically entails the splitting of a single column into a twocolumn configuration.However,this approach frequently necessitates tedious enumeration procedures,resulting in a considerable computational burden.To surmount this formidable challenge,the present study introduces an innovative remedy:The proposition of a superstructure that encompasses both single-column and multiple two-column configurations.Additionally,a simultaneous optimization algorithm is applied to optimize both the process parameters and heat integration structures of the twocolumn configurations.The effectiveness of this approach is demonstrated through a case study focusing on industrial organosilicon separation.The results underscore that the superstructure methodology not only substantially mitigates computational time compared to exhaustive enumeration but also furnishes solutions that exhibit comparable performance.

Innovation leading development:a glimpse into three-dimensional bioprinting in Israel

Three-dimensional(3D)printing has attracted increasing research interest as an emerging manufacturing technology for devel-oping sophisticated and exquisite architecture through hierarchical printing.It has also been employed in various advanced industrial areas.The development of intelligent biomedical engineering has raised the requirements for 3D printing,such as flexible manufacturing processes and technologies,biocompatible constituents,and alternative bioproducts.However,state-of-the-art 3D printing mainly involves inorganics or polymers and generally focuses on traditional industrial fields,thus severely limiting applications demanding biocompatibility and biodegradability.In this regard,peptide architectonics,which are self-assembled by programmed amino acid sequences that can be flexibly functionalized,have shown promising potential as bioinspired inks for 3D printing.Therefore,the combination of 3D printing and peptide self-assembly poten-tially opens up an alternative avenue of 3D bioprinting for diverse advanced applications.Israel,a small but innovative nation,has significantly contributed to 3D bioprinting in terms of scientific studies,marketization,and peptide architectonics,including modulations and applications,and ranks as a leading area in the 3D bioprinting field.This review summarizes the recent progress in 3D bioprinting in Israel,focusing on scientific studies on printable components,soft devices,and tissue engineering.This paper further delves into the manufacture of industrial products,such as artificial meats and bioinspired supramolecular architectures,and the mechanisms,physicochemical properties,and applications of peptide self-assembly.Undoubtedly,Israel contributes significantly to the field of 3D bioprinting and should thus be appropriately recognized.

The combined application of stem cells and three-dimensional bioprinting scaffolds for the repair of spinal cord injury

Spinal cord injury is considered one of the most difficult injuries to repair and has one of the worst prognoses for injuries to the nervous system.Following surgery,the poor regenerative capacity of nerve cells and the generation of new scars can make it very difficult for the impaired nervous system to restore its neural functionality.Traditional treatments can only alleviate secondary injuries but cannot fundamentally repair the spinal cord.Consequently,there is a critical need to develop new treatments to promote functional repair after spinal cord injury.Over recent years,there have been seve ral developments in the use of stem cell therapy for the treatment of spinal cord injury.Alongside significant developments in the field of tissue engineering,three-dimensional bioprinting technology has become a hot research topic due to its ability to accurately print complex structures.This led to the loading of three-dimensional bioprinting scaffolds which provided precise cell localization.These three-dimensional bioprinting scaffolds co uld repair damaged neural circuits and had the potential to repair the damaged spinal cord.In this review,we discuss the mechanisms underlying simple stem cell therapy,the application of different types of stem cells for the treatment of spinal cord injury,and the different manufa cturing methods for three-dimensional bioprinting scaffolds.In particular,we focus on the development of three-dimensional bioprinting scaffolds for the treatment of spinal cord injury.

Development of a toroidal soft x-ray imaging system and application for investigating three-dimensional plasma on J-TEXT

A toroidal soft x-ray imaging(T-SXRI)system has been developed to investigate threedimensional(3D)plasma physics on J-TEXT.This T-SXRI system consists of three sets of SXR arrays.Two sets are newly developed and located on the vacuum chamber wall at toroidal positionsφof 126.4°and 272.6°,respectively,while one set was established previously atφ=65.50.Each set of SXR arrays consists of three arrays viewing the plasma poloidally,and hence can be used separately to obtain SXR images via the tomographic method.The sawtooth precursor oscillations are measured by T-SXRI,and the corresponding images of perturbative SXR signals are successfully reconstructed at these three toroidal positions,hence providing measurement of the 3D structure of precursor oscillations.The observed 3D structure is consistent with the helical structure of the m/n=1/1 mode.The experimental observation confirms that the T-SXRI system is able to observe 3D structures in the J-TEXT plasma.

Three-dimensional cell-based strategies for liver regeneration

Liver regeneration and the development of effective therapies for liver failure remain formidable challenges in modern medicine.In recent years,the utilization of 3D cell-based strategies has emerged as a promising approach for addressing these urgent clinical requirements.This review provides a thorough analysis of the application of 3D cell-based approaches to liver regeneration and their potential impact on patients with end-stage liver failure.Here,we discuss various 3D culture models that incorporate hepatocytes and stem cells to restore liver function and ameliorate the consequences of liver failure.Furthermore,we explored the challenges in transitioning these innovative strategies from preclinical studies to clinical applications.The collective insights presented herein highlight the significance of 3D cell-based strategies as a transformative paradigm for liver regeneration and improved patient care.

Computer-assisted three-dimensional individualized extreme liver resection for hepatoblastoma in proximity to the major liver vasculature

BACKGROUND The management of hepatoblastoma(HB)becomes challenging when the tumor remains in close proximity to the major liver vasculature(PMV)even after a full course of neoadjuvant chemotherapy(NAC).In such cases,extreme liver resection can be considered a potential option.AIM To explore whether computer-assisted three-dimensional individualized extreme liver resection is safe and feasible for children with HB who still have PMV after a full course of NAC.METHODS We retrospectively collected data from children with HB who underwent surgical resection at our center from June 2013 to June 2023.We then analyzed the detailed clinical and three-dimensional characteristics of children with HB who still had PMV after a full course of NAC.RESULTS Sixty-seven children diagnosed with HB underwent surgical resection.The age at diagnosis was 21.4±18.8 months,and 40 boys and 27 girls were included.Fifty-nine(88.1%)patients had a single tumor,39(58.2%)of which was located in the right lobe of the liver.A total of 47 patients(70.1%)had PRE-TEXT III or IV.Thirty-nine patients(58.2%)underwent delayed resection.After a full course of NAC,16 patients still had close PMV(within 1 cm in two patients,touching in 11 patients,compressing in four patients,and showing tumor thrombus in three patients).There were 6 patients of tumors in the middle lobe of the liver,and four of those patients exhibited liver anatomy variations.These 16 children underwent extreme liver resection after comprehensive preoperative evaluation.Intraoperative procedures were performed according to the preoperative plan,and the operations were successfully performed.Currently,the 3-year event-free survival of 67 children with HB is 88%.Among the 16 children who underwent extreme liver resection,three experienced recurrence,and one died due to multiple metastases.CONCLUSION Extreme liver resection for HB that is still in close PMV after a full course of NAC is both safe and feasible.This approach not only reduces the necessity for liver transplantation but also results in a favorable prognosis.Individualized three-dimensional surgical planning is beneficial for accurate and complete resection of HB,particularly for assessing vascular involvement,remnant liver volume and anatomical variations.

Development and Validation of Integrated Nutrient Management Practices of Industrial Processing Varieties: Asterix and Courage in Bangladesh

An experiment was meticulously conducted at the research field of Bangabandhu Sheikh Mujibur Rahman Agricultural University (BSMRAU), Gazipur, Bangladesh, during the 2011-2012 potato growing season to develop integrated crop management practices for the potato seed production of industrial processing varieties Asterix and Courage. Significantly, higher growth and yield parameters were found in the BADC-recommended practice. Later, another experiment was conducted to validate the BADC practice during the 2013-2014 potato growing season in two locations in Bangladesh. Results showed that the production of tuber per hill, tuber weight per hill as well as gross tuber yield per plot, higher proportion of storable seed tubers, and more quality seed potatoes (A-grade and B-grade) seed tubers were found significantly higher in the “BADC developed practice” compared to other treatments. Viral diseases (PLRV and PVY) prevalence was lower in “BADC developed practice”. Moreover, “BADC developed practice” contributed more economic yield by minimizing input cost compared to “Munshiganj advanced farmers’ practice”. Therefore, the “BADC developed practice” was found “superior” regarding yield, quality, and profitability in seed potato production of industrial varieties—Asterix and Courage in Bangladesh.

Impacts of Integrated Multi-Trophic Aquaculture on Phytoplankton in Sanggou Bay

Integrated multi-trophic aquaculture(IMTA)has been considered as an ecofriendly culture system providing a potential solution to environmental risks caused by intensive monoculture system.However,the impact of IMTA on phytoplankton remains unclear.In this study,the spatial and temporal variations of phytoplankton in Sanggou Bay were investigated seasonally based on 21 sampling sites covering three cultivation zones(bivalve zone,IMTA zone,and kelp zone)and one control zone(without aquatic cultivation).In total,128 phytoplankton species,with diatoms and dinoflagellates as the dominant groups,were obtained across the whole year,and the mean Shannon diversity index(H')and species richness(SR)were determined as 1.39 and 9.39,respectively.The maximum chlorophyll a(Chl-a)(6.32μg L^(-1))and plankton diversity(H'of 1.97)occurred in summer and autumn,respectively.Compared to other zones,the bivalve zone displayed significantly higher Chl-a and lower H'in majority of time.Pairwise PERMANOVA analysis indicated that the phytoplankton assemblage in the bivalve zone was significantly different with the control and kelp zones,while the IMTA zone maintained close to other three zones.Based on generalized additive models,temperature,NO_(2)^(-)-N,N/P ratio,SiO_(3)^(2-)-Si,and salinity were determined as the key factors underlying Chl-a and phytoplankton diversity.Addi-tionally,the results of redundancy analysis further indicated that the phytoplankton assemblage in the bivalve zone is positively re-lated with nutrients such as NO_(3)^(-)-N and NH_(4)^(+)-N as well as water depth,while the phytoplankton assemblages in the kelp,control,and IMTA zones are associated with NO_(2)^(-)-N,SiO_(3)^(2-)-Si,and salinity.Taken all observations into consideration together,it can be inferred that IMTA can effectively reduce Chl-a level compared to bivalve monoculture by reducing the nutrients.However,the SR,H’,and species composition of phytoplankton are primarily determined by local environment factors such as temperature,water depth,salinity and SiO_(3)^(2-)-Si.

Carbon nanotube integrated circuit technology:purification,assembly and integration

As the manufacturing process of silicon-based integrated circuits(ICs)approaches its physical limit,the quantum effect of silicon-based field-effect transistors(FETs)has become increasingly evident.And the burgeoning carbon-based semiconductor technology has become one of the most disruptive technologies in the post-Moore era.As one-dimensional nanomaterials,carbon nanotubes(CNTs)are far superior to silicon at the same technology nodes of FETs because of their excellent electrical transport and scaling properties,rendering them the most competitive material in the next-generation ICs technology.However,certain challenges impede the industrialization of CNTs,particularly in terms of material preparation,which significantly hinders the development of CNT-based ICs.Focusing on CNT-based ICs technology,this review summarizes its main technical status,development trends,existing challenges,and future development directions.

Command filtered integrated estimation guidance and control for strapdown missiles with circular field of view

In this paper,an integrated estimation guidance and control(IEGC)system is designed based on the command filtered backstepping approach for circular field-of-view(FOV)strapdown missiles.The threedimensional integrated estimation guidance and control nonlinear model with limited actuator deflection angle is established considering the seeker's FOV constraint.The boundary time-varying integral barrier Lyapunov function(IBLF)is employed in backstepping design to constrain the body line-of-sight(BLOS)in IEGC system to fit a circular FOV.Then,the nonlinear adaptive controller is designed to estimate the changing aerodynamic parameters.The generalized extended state observer(GESO)is designed to estimate the acceleration of the maneuvering targets and the unmatched time-varying disturbances for improving tracking accuracy.Furthermore,the command filters are used to solve the"differential expansion"problem during the backstepping design.The Lyapunov theory is used to prove the stability of the overall closed-loop IEGC system.Finally,the simulation results validate the integrated system's effectiveness,achieving high accuracy strikes against maneuvering targets.

Three-dimensional stability calculation method for high and large composite slopes formed by mining stope and inner dump in adjacent open pits

The 2D limit equilibrium method is widely used for slope stability analysis.However,with the advancement of dump engineering,composite slopes often exhibit significant 3D mechanical effects.Consequently,it is of significant importance to develop an effective 3D stability calculation method for composite slopes to enhance the design and stability control of open-pit slope engineering.Using the composite slope formed by the mining stope and inner dump in Baiyinhua No.1 and No.2 open-pit coal mine as a case study,this research investigates the failure mode of composite slopes and establishes spatial shape equations for the sliding mass.By integrating the shear resistance and sliding force of each row of microstrip columns onto the bottom surface of the strip corresponding to the main sliding surface,a novel 2D equivalent physical and mechanical parameters analysis method for the strips on the main sliding surface of 3D sliding masses is proposed.Subsequently,a comprehensive 3D stability calculation method for composite slopes is developed,and the quantitative relationship between the coordinated development distance and its 3D stability coefficients is examined.The analysis reveals that the failure mode of the composite slope is characterized by cutting-bedding sliding,with the arc serving as the side interface and the weak layer as the bottom interface,while the destabilization mechanism primarily involves shear failure.The spatial form equation of the sliding mass comprises an ellipsoid and weak plane equation.The analysis revealed that when the coordinated development distance is 1500 m,the error rate between the 3D stability calculation result and the 2D stability calculation result of the composite slope is less than 8%,thereby verifying the proposed analytical method of equivalent physical and mechanical parameters and the 3D stability calculation method for composite slopes.Furthermore,the3D stability coefficient of the composite slope exhibits an exponential correlation with the coordinated development distance,with the coefficient gradually decreasing as the coordinated development distance increases.These findings provide a theoretical guideline for designing similar slope shape parameters and conducting stability analysis.

Computed tomography three-dimensional reconstruction in the diagnosis of bleeding small intestinal polyps:A case report

BACKGROUND Computed tomography(CT)small bowel three-dimensional(3D)reconstruction is a powerful tool for the diagnosis of small bowel disease and can clearly show the intestinal lumen and wall as well as the outside structure of the wall.The horizontal axis position can show the best adjacent intestinal tube and the lesion between the intestinal tubes,while the coronal position can show the overall view of the small bowel.The ileal end of the localization of the display of excellent,and easy to quantitative measurement of the affected intestinal segments,the sagittal position for the rectum and the pre-sacral lesions show the best,for the discovery of fistulae is also helpful.Sagittal view can show rectal and presacral lesions and is useful for fistula detection.It is suitable for the assessment of inflammatory bowel disease,such as assessment of disease severity and diagnosis and differential diagnosis of the small bowel and mesenteric space-occupying lesions as well as the judgment of small bowel obstruction points.CASE SUMMARY Bleeding caused by small intestinal polyps is often difficult to diagnose in clinical practice.This study reports a 29-year-old male patient who was admitted to the hospital with black stool and abdominal pain for 3 months.Using the combination of CT-3D reconstruction and capsule endoscopy,the condition was diagnosed correctly,and the polyps were removed using single-balloon enteroscopyendoscopic retrograde cholangiopancreatography without postoperative complications.CONCLUSION The role of CT-3D in gastrointestinal diseases was confirmed.CT-3D can assist in the diagnosis and treatment of gastrointestinal diseases in combination with capsule endoscopy and small intestinal microscopy.

Research on Quantitative Identification of Three-Dimensional Connectivity of Fractured-Vuggy Reservoirs

The fractured-vuggy carbonate oil resources in the western basin of China are extremely rich.The connectivity of carbonate reservoirs is complex,and there is still a lack of clear understanding of the development and topological structure of the pore space in fractured-vuggy reservoirs.Thus,effective prediction of fractured-vuggy reservoirs is difficult.In view of this,this work employs adaptive point cloud technology to reproduce the shape and capture the characteristics of a fractured-vuggy reservoir.To identify the complex connectivity among pores,fractures,and vugs,a simplified one-dimensional connectivity model is established by using the meshless connection element method(CEM).Considering that different types of connection units have different flow characteristics,a sequential coupling calculation method that can efficiently calculate reservoir pressure and saturation is developed.By automatic history matching,the dynamic production data is fitted in real-time,and the characteristic parameters of the connection unit are inverted.Simulation results show that the three-dimensional connectivity model of the fractured-vuggy reservoir built in this work is as close as 90%of the fine grid model,while the dynamic simulation efficiency is much higher with good accuracy.

Design of compact integrated diamond nitrogen-vacancy center quantum probe

An integrated quantum probe for magnetic field imaging is proposed,where the nitrogen–vacancy(NV)center fixed at the fiber tip is located on the periphery of flexible ring resonator.Using flexible polyimide(PI)as the substrate medium,we design a circular microstrip antenna,which can achieve a bandwidth of 140 MHz at Zeeman splitting frequency of 2.87 GHz,specifically suitable for NV center experiments.Subsequently,this antenna is seamlessly fixed at a three-dimensional-printed cylindrical support,allowing the optical fiber tip to extend out of a dedicated aperture.To mitigate errors originating from processing,precise tuning within a narrow range can be achieved by adjusting the conformal amplitude.Finally,we image the microwave magnetic field around the integrated probe with high resolution,and determine the suitable area for placing the fiber tip(SAP).

Development of an Integrated Disposable Device for SARSCoV-2 Nucleic Acid Extraction and Detection

Objective To develop a highly sensitive and rapid nucleic acid detection method for the severe acute respiratory syndrome coronavirus 2(SARS-CoV-2).Methods We designed,developed,and manufactured an integrated disposable device for SARS-CoV-2 nucleic acid extraction and detection.The precision of the liquid transfer and temperature control was tested.A comparison between our device and a commercial kit for SARS-Cov-2 nucleic acid extraction was performed using real-time fluorescence reverse transcription polymerase chain reaction(RT-PCR).The entire process,from SARS-CoV-2 nucleic acid extraction to amplification,was evaluated.Results The precision of the syringe transfer volume was 19.2±1.9μL(set value was 20),32.2±1.6(set value was 30),and 57.2±3.5(set value was 60).Temperature control in the amplification tube was measured at 60.0±0.0℃(set value was 60)and 95.1±0.2℃(set value was 95)respectively.SARS-Cov-2 nucleic acid extraction yield through the device was 7.10×10^(6) copies/mL,while a commercial kit yielded 2.98×10^(6) copies/mL.The mean time to complete the entire assay,from SARS-CoV-2 nucleic acid extraction to amplification detection,was 36 min and 45 s.The detection limit for SARS-CoV-2 nucleic acid was 250 copies/mL.Conclusion The integrated disposable devices may be used for SARS-CoV-2 Point-of-Care test(POCT).

Application of three-dimensional speckle tracking technique in measuring left ventricular myocardial function in patients with diabetes

BACKGROUND Diabetic cardiomyopathy is considered as a chronic complication of diabetes mellitus(DM).Therefore,early detection of left ventricular systolic function(LVSF)damage in DM is essential.AIM To explore the use of the three-dimensional speckle tracking technique(3D-STI)for measuring LVSF in DM patients via meta-analysis.METHODS The electronic databases were retrieved from the initial accessible time to 29 April 2023.The current study involved 9 studies,including 970 subjects.We carried out this meta-analysis to estimate myocardial function in DM compared with controls according to myocardial strain attained by 3D-STI.RESULTS Night articles including 970 subjects were included.No significant difference was detected in the left ventricular ejection fraction between the control and the diabetic group(P>0.05),while differences in global longitudinal strain,global circumferential strain,global radial strain,and global area strain were markedly different between the controls and DM patients(all P<0.05).CONCLUSION The 3D-STI could be applied to accurately measure early LVSF damage in patients with DM.

Obstacles to the Integrated Care of Children Aged 6 to 59 Months Suffering from Acute and Severe Malnutrition at the Chu-Me and HATC of N’Djamena/Chad

Introduction: the problem of Severe Acute Malnutrition (SAM) and its consequences concern and challenge all social actors worldwide. The objective of the study was to identify the real obstacles that actors face in the integrated management of children aged 6 - 59 months suffering from SAM at the University Hospital of Mother and Child (CHUME) and the Chad-China Friendship Hospital (HATC) of N’Djamena. Methodology: this is a cross-sectional descriptive and interpretative study conducted from January to October 2023 at the CHUME and HATC of N’Djamena. It is based on questionnaires and direct observation of two hundred and thirty-six (236) parents or guardians of malnourished children admitted to these health facilities. All 236 agreed to participate freely in this study. Results: it appears from this study that the obstacles to the integrated management of malnourished children were: poor care-care relationship (26.7%) permanent product breaks (22.9%), the direct costs of services ranged from 30,000 to 60,000 FCFA (41.53%), drugs used for the treatment of patients came from the street (66.10%), malaria and anemia occupy an important place (27.5%), 57.2% respondents had monthly income below 60,000 CFAF. Conclusion: the present study carried out has identified the real bottlenecks to the integrated management of children suffering from SAM in the therapeutic nutritional units of the city of N’Djamena. .