The theoretical solutions are obtained for the three-dimensional(3-D)stress field in an infinite isotropic elastic plate with a through-the-thickness circular hole subjected to shear load at far field by using Kane an...The theoretical solutions are obtained for the three-dimensional(3-D)stress field in an infinite isotropic elastic plate with a through-the-thickness circular hole subjected to shear load at far field by using Kane and Mindlin′s assumption based on the stress function method.Based on the present solutions,the characteristics of 3-D stress field are analyzed and the emphasis is placed on the effects of the plate thickness and Poisson′s ratio on the deviation of the present 3-D in-plane stress from the related plane stress solutions,the stress concentration and the out-of-plane constraint.The present solutions show that the stress concentration factor reaches its peak value of about 8.9% which is higher than that of the plane stress solutions.As expected,the out-of-plane stress constraint factor can reach 1on the surface of the hole when the plate is a very thick one.展开更多
The singularity of stress and strain at the tip of three-dimensional notch isanalysed by the power expansion method .the eigenquation of the notch is gainedthrough the boundary conditions of the notch, the eigenvalue...The singularity of stress and strain at the tip of three-dimensional notch isanalysed by the power expansion method .the eigenquation of the notch is gainedthrough the boundary conditions of the notch, the eigenvalues under different innerangles of the notch are obtained, the expression of stress and strain at the tip of thenotch is finally derived .展开更多
Through detailed three-dimensional （3D） finite element （FE） calculations, the out-of-plane constraints Tz along embedded center-elliptical cracks in mode I elastic plates are studied. The distributions of Tz are o...Through detailed three-dimensional （3D） finite element （FE） calculations, the out-of-plane constraints Tz along embedded center-elliptical cracks in mode I elastic plates are studied. The distributions of Tz are obtained near the crack front with aspect ratios （a/c） of 0.2, 0.4, 0.5, 0.6, 0.8 and 1.0. Tz decreases from an approximate value of Poisson ratio v at the crack tip to zero with increasing normalized radial distances （r/a） in the normal plane of the crack front line, and increases gradually when the elliptical parameter angle φ changes from 0° to 90°at the same r/a. With a/c rising to 1.0, Tz is getting nearly independent of φ and is only related to r/a. Based on the present FE calculations for Tz, empirical formulas for Tz are obtained to describe the 3D distribution of Tz for embedded center-elliptical cracks using the least squares method in the range of 0.2 ≤ a/c ≤ 1.0. These Tz results together with the corresponding stress intensity factor K are well suitable for the analysis of the 3D embedded centerelliptical crack from field, and a two-parameter K-Tz principle is proposed.展开更多
It has been widely studied about the final residual stress and deformation in muhipass welding of thick weldments. But there is a lack of a clear understanding of the interrelationship of interpass stress and deformat...It has been widely studied about the final residual stress and deformation in muhipass welding of thick weldments. But there is a lack of a clear understanding of the interrelationship of interpass stress and deformation during multipass welding. In this study, a three dimension numerical model of a sixteen-pass double V-groove welded joint with 50 mm plate is developed to compute the stress field and deformation by using multiple CPU parallel processing technology. The following factors such as the non-linear of temperature, heat radiation, filling of material step by step and so on are considered. Distribution and evolution law of welding stress in the transverse and longitudinal section is analyzed in this paper, and the interpnss stresses are studied also. At the same time the evolution course of angular deformation amount is analyzed, and the experimental results show that the calculated resuhs accord with the measured results of angular deformation.展开更多
Stress raisers such as holes are inevitable in structures at which stress concentration occurs and the static as well as fatigue strength of the structures can be significantly weakened. Therefore, to accurately evalu...Stress raisers such as holes are inevitable in structures at which stress concentration occurs and the static as well as fatigue strength of the structures can be significantly weakened. Therefore, to accurately evaluate the stress concentration factor and stress fields at holes is of essential importance for structure design and service life prediction. Although stress and strain concentration and fields at holes in finite thickness plates strongly change with and along the thickness, manuals of stress concentration for engineering design are mainly based on twodimensional theory and no explicit formula is available even for circular holes in finite thickness plates. Here we obtain for the first time a complete set of explicit formulae for stress and strain concentration factors and the out-of-plane constraint factor at circular as well as elliptical holes in finite thickness plates by integrating comprehensive three-dimensional finite element analyses and available theoretical solutions. The three-dimensional stress distributions ahead of holes can also be predicted by the obtained formulae. With their accuracy and the corresponding applicable range being analyzed and outlined in detail, the formulae can serve as an important fundamental solution for three-dimensional engineering structure design and guideline for developing threedimensional analytical methods.展开更多
基金Supported by the National Natural Science Foundation of China(11372269,10902057)
文摘The theoretical solutions are obtained for the three-dimensional(3-D)stress field in an infinite isotropic elastic plate with a through-the-thickness circular hole subjected to shear load at far field by using Kane and Mindlin′s assumption based on the stress function method.Based on the present solutions,the characteristics of 3-D stress field are analyzed and the emphasis is placed on the effects of the plate thickness and Poisson′s ratio on the deviation of the present 3-D in-plane stress from the related plane stress solutions,the stress concentration and the out-of-plane constraint.The present solutions show that the stress concentration factor reaches its peak value of about 8.9% which is higher than that of the plane stress solutions.As expected,the out-of-plane stress constraint factor can reach 1on the surface of the hole when the plate is a very thick one.
文摘The singularity of stress and strain at the tip of three-dimensional notch isanalysed by the power expansion method .the eigenquation of the notch is gainedthrough the boundary conditions of the notch, the eigenvalues under different innerangles of the notch are obtained, the expression of stress and strain at the tip of thenotch is finally derived .
基金The project supported by the National Natural Science Foundation of China （50275073）
文摘Through detailed three-dimensional （3D） finite element （FE） calculations, the out-of-plane constraints Tz along embedded center-elliptical cracks in mode I elastic plates are studied. The distributions of Tz are obtained near the crack front with aspect ratios （a/c） of 0.2, 0.4, 0.5, 0.6, 0.8 and 1.0. Tz decreases from an approximate value of Poisson ratio v at the crack tip to zero with increasing normalized radial distances （r/a） in the normal plane of the crack front line, and increases gradually when the elliptical parameter angle φ changes from 0° to 90°at the same r/a. With a/c rising to 1.0, Tz is getting nearly independent of φ and is only related to r/a. Based on the present FE calculations for Tz, empirical formulas for Tz are obtained to describe the 3D distribution of Tz for embedded center-elliptical cracks using the least squares method in the range of 0.2 ≤ a/c ≤ 1.0. These Tz results together with the corresponding stress intensity factor K are well suitable for the analysis of the 3D embedded centerelliptical crack from field, and a two-parameter K-Tz principle is proposed.
基金National Natural Science Foundation of China (No. 50775053, 50675046)
文摘It has been widely studied about the final residual stress and deformation in muhipass welding of thick weldments. But there is a lack of a clear understanding of the interrelationship of interpass stress and deformation during multipass welding. In this study, a three dimension numerical model of a sixteen-pass double V-groove welded joint with 50 mm plate is developed to compute the stress field and deformation by using multiple CPU parallel processing technology. The following factors such as the non-linear of temperature, heat radiation, filling of material step by step and so on are considered. Distribution and evolution law of welding stress in the transverse and longitudinal section is analyzed in this paper, and the interpnss stresses are studied also. At the same time the evolution course of angular deformation amount is analyzed, and the experimental results show that the calculated resuhs accord with the measured results of angular deformation.
基金supported by the National Natural Science Foundation of China (51535005,51472117)the Research Fund of State Key Laboratory of Mechanics and Control of Mechanical Structures (MCMS-I-0418K01,MCMS-I-0418Y01,MCMS-0417G02, MCMS-0417G03)+1 种基金the Fundamental Research Funds for the Central Universities (NP2017101, NC2018001)a project funded by the Priority Academic Program Development of Jiangsu Higher Education Institutions.The authors would like to thank Dr. Chongmin She for helpful discussions).
文摘Stress raisers such as holes are inevitable in structures at which stress concentration occurs and the static as well as fatigue strength of the structures can be significantly weakened. Therefore, to accurately evaluate the stress concentration factor and stress fields at holes is of essential importance for structure design and service life prediction. Although stress and strain concentration and fields at holes in finite thickness plates strongly change with and along the thickness, manuals of stress concentration for engineering design are mainly based on twodimensional theory and no explicit formula is available even for circular holes in finite thickness plates. Here we obtain for the first time a complete set of explicit formulae for stress and strain concentration factors and the out-of-plane constraint factor at circular as well as elliptical holes in finite thickness plates by integrating comprehensive three-dimensional finite element analyses and available theoretical solutions. The three-dimensional stress distributions ahead of holes can also be predicted by the obtained formulae. With their accuracy and the corresponding applicable range being analyzed and outlined in detail, the formulae can serve as an important fundamental solution for three-dimensional engineering structure design and guideline for developing threedimensional analytical methods.
