Direct-chill semi-continuous casting process of three-layer composite ingot of 4045/3004/4045 aluminum alloys

Three-layer composite ingot of 4045/3004/4045 aluminum alloys was prepared by direct-chill semi-continuous casting process,the temperature field distribution near the composite interface,macro-morphology,microstructure and composition distribution of the composite interface were investigated.The results show that semi-solid layer with a certain thickness forms near the interface due to the effect of cooling plate,which ensures successful implementation of casting the composite ingot.Two different aluminum alloys are well bonded metallurgically.The mechanical properties of composite interface were measured,the tensile and shearing strengths of composite interface are 105 and 88 MPa,respectively,which proves that the composite interface is a kind of metallurgical bonding.

Effects of annealing process on sagging resistance of cold-rolled three-layer Al alloy clad sheets

The effectsof annealing process on the hardness, microstructure, Si diffusion, and the sagging resistance of cold-rolled 4343/3003/4343 Al alloy clad sheets and their 3003 Al alloy core sheets were experimentally investigated through hardness tests, EBSD observations, EDS analysis, and sagging test.The results showedthat with the increase of annealing temperature, the hardness of both clad sheet and core sheet decreased, while thesaggingresistancesof both clad and core sheets achieved maximum values after annealing at 380℃ for 1h. After annealing at 380℃, the clad layer contained fine and equiaxedrecrystallized grains; the core layer was composed of fully recrystallized coarse grains elongated along the rolling direction. The Si diffusion from the clad layer to the core zone was limited. After annealing at a higher temperature of 440℃ or 550℃, thesaggingresistance of clad sheets worsened precipitously. The grains in the clad layer grew up, obscuring the interface between the clad and core layer; the recrystallized grains in the core layer became finer. Significant amount of Si penetrated into the core layer through the accelerated diffusion. Compared with the microstructure refinement, Si diffusion is the main factor influencing thesaggingresistance.

基于第一性原理研究CO在C_(21)Si上的吸附

通过密度泛函理论(DFT)计算研究了单个CO分子分别在C_(21)Si上的吸附.由于结构中含有21个C原子以及引入一个Si原子,命名为(C_(21)Si).计算了体系中最稳定的几何结构、吸附能、吸附高度和态密度,研究了吸附的CO分子与基底之间的相互作用.研究发现,当CO放置在C_(21)Si上吸附时,C原子靠近吸附优于O原子靠近时的吸附,吸附能分别为-0.86 eV和-0.36 eV,当O原子靠近吸时二者之间的吸附反应较弱,为物理吸附.C原子靠近时的吸附高度小,吸附反应更强,为化学吸附.根据态密度轨道之间的杂化程度,说明二者之间存在吸附反应,相较于O原子靠近吸附,基底对C原子靠近时的吸附能力更强,敏感度更高.

A Short-Term Traffic Flow Forecasting Method Based on a Three-Layer K-Nearest Neighbor Non-Parametric Regression Algorithm

Short-term traffic flow is one of the core technologies to realize traffic flow guidance. In this article, in view of the characteristics that the traffic flow changes repeatedly, a short-term traffic flow forecasting method based on a three-layer K-nearest neighbor non-parametric regression algorithm is proposed. Specifically, two screening layers based on shape similarity were introduced in K-nearest neighbor non-parametric regression method, and the forecasting results were output using the weighted averaging on the reciprocal values of the shape similarity distances and the most-similar-point distance adjustment method. According to the experimental results, the proposed algorithm has improved the predictive ability of the traditional K-nearest neighbor non-parametric regression method, and greatly enhanced the accuracy and real-time performance of short-term traffic flow forecasting.

Structure Design and Properties of Three-Layer Particleboard Based on High Voltage Electrostatic Field(HVEF)

In this study,the effects of three different particle sizes of wood wastes(A=–8+12 mesh;B=–12+20 mesh;C=–20+30 mesh)and factory shavings(D)on the properties of particleboard were investigated.According to the test results,three-layer particleboard was designed.Particleboard face layers made with mixture of A,B,and C.The core layer made with D.The ratio of core layer to face layers is 50:50.Three-layer particleboard were fabricated with 12%urea-formaldehyde(UF)resins and three different high voltage electrostatic field intensities(0 kv,30 kv,60 kv).The internal bond(IB)strength,modulus of rupture(MOR),modulus of elasticity(MOE),thickness swelling(TS),and water absorption(WA)of particleboard were evaluated.The density distribution of the three-layer particleboard were examined by vertical density profiles(VDP),and the bonding mechanism and functional groups changes in the particles were analyzed by FTIR analysis.The results showed that HVEF treatment intensity play a remarkable role in properties of particleboard.The particleboard with higher electrostatic field intensities treatment has higher MOE,MOR,IB,and TS.Under HVEF treatment(60 kv),the MOR,modulus of MOE,and IB of three-layer particleboard were 23.61 N/mm^(2),2787.09 N/mm^(2),and 0.86 N/mm^(2),respectively.FTIR indicated that the surface activity of wood particles was increased electric field treatment.

Characteristics Analysis of Chemical Concentration Sensor Based on Three-layer FBG

The three-layer structure model of the fiber Bragg grating is proposed in this paper. And through experimental study and reasoning calculation to verify the three layer structure of the optical waveguide model, so the sensitivity characteristic of the Bragg wavelength to the refractive index of chemical solution is obtained. And the relationships between the concentration and the shift of Bragg wavelength of sucrose, ethanol, and Nacl solution are achieved. Finally the shifts of the Bragg wavelength with the external concentration are obtained by experiments. A kind of simple structure, small size, good stability, high sensitivity chemical concentration sensor is obtained.

A Three-layered Contrasting Analysis of the Theme in Once more to the lake

Once more to the lake is a representative work of the American Writer, Elwyn Brooks White, and has been acclaimed by people in the world. The paper offers a three-layered contrasting analysis of the essay. By detailed analysis of the contrasts running through the whole essay, the author finds that those contrasts are symbol of White's internal struggle and reflection for life.On the foundation of the three-layered contrasts, the paper presents the theme analysis and clarifies the content of the essay.

One-step hydrothermal synthesis of 2,5-PDCA-containing MgAl-LDHs three-layer composite coating with high corrosion resistance on AZ31

The addition of 2,5-pyridinedicarboxylic acid(2,5-PDCA)to the Mg-Al LDH coating,which was prepared by one-step hydrothermal synthesis,had extremely enhanced the corrosion protection of AZ31 Mg alloy,although the 2,5-PDCA could not be intercalated into the interlayer spacing.The corrosion current density of 0.05 mol L^(−1)2,5-PDCA LDH containing LDH coating is 3.18 nA cm^(−2),reduced by two orders of magnitude compared to the LDH coating without inhibitor,and the corrosion inhibition efficiency of the coating is 98.05%.The coating formed on the surface of AZ31 was peeled off from the substrate by using a mechanical method and SEM observation of the cross-section showed that the coating consisted of three different layers.The innermost layer is a thick layer that consists of Mg(OH)_(2)and the intermediate layer is LDH,which is vertical to the substrate and the outmost layer is a thin but very dense deposit layer of LDH agglomerates with complexes of 2,5-PDCA and Mg.This kind of sediment/LDH/Mg(OH)_(2)three-layer composite structure was accountable for the increase in the corrosion resistance of AZ31 Mg alloy.

Study on Three-layered Grid Conceptual Prototype Using Ecological Network Computing Environment

Next generation grid systems where the emphasis shifts to distributed global collaboration, a service-oriented approach and information layer issues exhibit a strong sense of automation. Requirements for these systems resemble the self-organizing and the healing properties of natural ecosystems. Some key ecological concepts and mechanisms are introduced into the design for the third generation grid computing architectures by inspiration of this resemblance. Also, an Ecological Network-based Computing Environment (ENCE) platform is designed in this paper. Based on the ENCE platform, a grid-computing model of three-layered grid conceptual prototype that embeds the ENCE layers is presented from the viewpoint of implementation. The implementation model should be useful to the design of the third generation grid systems.

Third-order Stokes wave solutions for interfacial internal waves in a three-layer density-stratified fluid

Interracial internal waves in a three-layer density-stratified fluid are investigated using a singular perturbation method, and third-order asymptotic solutions of the velocity potentials and third-order Stokes wave solutions of the associated elevations of the interfacial waves are presented based on the small amplitude wave theory. As expected, the third-order solutions describe the third-order nonlinear modification and the third-order nonlinear interactions between the interracial waves. The wave velocity depends on not only the wave number and the depth of each layer but also on the wave amplitude.

On the three-layer passage reading method in English extensive reading

This paper raises, for the first time, with a model reading passage, a three-layer passage reading method （3LPRM in brief ） in English reading： reading beyond paragraphs; reading within paragraphs and sentences, and reading with coherences of words and expressions. The paper illustrates the definition, contents, characteristics and application of the method which is easy to master and apply. The paper aims at supplying readers especially beginners of E/S/FL （English as second/foreign language） with a practical passage reading method so as to improve their reading efficiency. The paper has some practical significance and directing value.

Improving electrochemical performances of LiFePO_4 /C cathode material via a novel three-layer electrode

As an improvement on the conventional two-layer electrode （active material layerlcurrent collector）, a novel sandwich-like three-layer electrode （conductive layerlactive material layertcurrent collector） for cathode material LiFePO4/C was introduced in order to improve its electrochemical performance. LiFePO4/C in the three-layer electrode exhibited superior rate capability in comparison with that in the two-layer electrode in accordance with charge-discharge examination. Cyclic voltammetry and electrochemical impedance spectroscopy indicated that Fe3＋/Fe2＋ redox couple for LiFePO4 in the three-layer electrode displayed faster kinetics, better reversibility and much lower charge transfer resistance than that in the two-layer electrode in electrochemical process. For three-layer electrode, the holes in the surface of active material layer were filled by smaller acetylene black grains, which formed electrical connections and provided more pathways to electron transport to/from LiFePO4/C particles exposed to the bulk electrolyte.

不同固溶处理对亚共晶Al-Si合金组织和性能的影响

铸态的亚共晶Al-Si合金中,粗大的α-Al晶粒和针片状共晶Si是造成其性能降低的主要原因。通过对Al-Ti-La和Nd细化变质后的Al-7Si合金进行了不同条件的固溶处理,研究了不同固溶温度和时间对其微观组织及性能的影响。结果表明:铸态Al-7Si合金随着固溶温度的升高,二次枝晶臂间距(SDAS)逐渐增大,共晶Si尺寸逐渐减小,并且共晶Si由长条状和纤维状向短棒状转变。随着固溶时间的延长,共晶Si的演变过程为:长条状→短棒状→粒状→粗化长大。当固溶温度为535℃、固溶时间为3 h时,合金的显微硬度为62.5 HV,相比于铸态提升了10.5%,极限抗拉强度(UTS)和断裂延伸率(El)由铸态的170.2 MPa和11.1%提升至174.0 MPa和13.1%,分别提升2.2%和18.0%,断口的解理平台小且出现大面积韧窝,由脆性断裂转变为韧性断裂。

Si含量对汽车用铝合金组织和性能的影响

制备了不同Si掺杂质量分数的汽车用铝合金材料,通过XRD、OM、SEM、力学性能试验和摩擦磨损试验研究了Si质量分数对铝合金物相结构、显微组织、硬度、拉伸强度、磨损性能和磨损形貌的影响。结果表明,铝合金主要是由α-Al、Mg、Si以及第二相Mg_(2)Si和Mg_(17)Al_(12)组成,Si掺杂质量分数的增加细化了珊瑚状的α-Al相,第二相主要析出在晶界处。随着Si掺杂质量分数的增加,铝合金的拉伸强度和硬度先增大后减小,屈服强度持续增大,断裂延伸率持续降低,Si掺杂质量分数3%的铝合金的拉伸强度达到最大值264.8 MPa,对应的屈服强度为189.6 MPa,硬度为最大值58.8 HV,对应的断裂延伸率为10.6%。磨损测试结果表明,磨损量和摩擦系数均随Si掺杂质量分数的增加表现出先降低后增大的趋势,当Si掺杂质量分数为3%时,铝合金的摩擦系数和磨损量均达到了最低值,分别为0.052及64.8 mg,铝合金的耐磨损性能最佳,磨损面中犁沟的方向均匀一致。

氟碳铈矿除Ca、Si制备脱硝催化剂及其脱硝性能的研究

包头混合稀土精矿是氟碳铈矿(CeCO_(3)F)和独居石(CePO_(4))的共生矿物,结构复杂,难以分解,且Ca、Si杂质嵌布在矿物表面,影响了稀土矿物的脱硝活性,因此在使用天然矿物作为催化剂之前,有必要对其进行除杂预处理。采用酸浸固氟焙烧方案将氟碳铈矿制成脱硝催化剂,具体工艺为:第一步,HCl除Ca,HCl浓度为6mol/L,氟碳铈矿与NaCl(固氟剂)质量比为1∶5,混合并搅拌12h后于500℃下焙烧2h;第二步,HF除Si,HF浓度为13mol/L,除Ca后粉末与NaCl质量比为1∶5,混合并搅拌12h后于500°C下焙烧2h。氟碳铈矿除Ca、Si后制备的催化剂中Ca含量降至1.85%,Si含量降至0.17%,稀土元素含量相比原矿提高了约22%。氟碳铈矿除Ca、Si后,表面形成了发达的孔结构,比表面积增大,活性元素增多,且部分Ce的价态由+3价转变为+4价,还形成了晶格氧,这些组织结构的变化为催化剂脱硝过程提供了更多的氧化还原中心,使得催化剂脱硝性能显著提高。因此,用除杂后的氟碳铈矿作脱硝催化剂比直接用天然矿物具有更大的优势。

基于UIS测试的Si/SiC级联器件雪崩特性分析

与机械式断路器相比,使用半导体功率器件构成的直流固态断路器在响应时间方面有较大的优势。由低压硅金属—氧化物—半导体场效应晶体管(Si MOSFET)和高压碳化硅结型场效应晶体管(SiC JFET)构成的Si/SiC级联型器件具有优异的开断特性。半导体功率器件可靠性一直是直流固态断路器所关注的焦点问题,非箝位感性负载开关(unclamped inductive switching,UIS)测试是评估半导体功率器件可靠性的重要方法。文中通过实验和仿真的方式分析了Si/SiC级联器件在非箝位感性负载开关过程的雪崩特性。首先,通过增加器件导通时间得到了不同负载电流下的雪崩特性,结果表明,随着导通时间的增加,Si/SiC级联器件在雪崩期间出现了雪崩电压下降的异常特性。随后,通过分立式Si/SiC级联器件进行UIS测试,发现异常特性是由于SiC JFET在雪崩期间出现导通而形成的。最后,通过Si/SiC级联器件的三维电—热耦合仿真,结果表明雪崩期间SiC JFET芯片栅极铝金属层和键合线温度升高,导致SiC JFET栅极等效电阻增加,最终使得SiC JFET在雪崩期间出现导通。

低压Si MOSFETs对SiC/Si级联器件短路特性的影响

由低压硅金属-氧化物-半导体场效应晶体管(Silicon Metal-Oxide-Semiconductor Field-Effect Transistor, Si MOSFET)和碳化硅结型场效应晶体管(Silicon Carbon Junction Field-Effect Transistor, SiC JFET)构成的SiC/Si级联(Cascode)器件,兼具了低压Si MOSFET易于驱动、SiC JFET高耐压低损耗等优点。该文采用实验和数值模拟的方式研究了低压Si MOSFET对SiC/Si级联器件短路特性的影响,结果表明,在短路过程中SiC/Si级联器件中的SiC JFET最高温度比单独的SiC JFET短路时的最高温度低,SiC/Si级联器件的短路失效时间得到了延长,并且随着Si MOSFET额定电压的增加,SiC/Si级联器件短路失效延长的时间也在增加。

Y/Al-5Ti-1B复合变质对Al-7Si合金微观组织和力学性能的影响

在传统铸造Al-Si合金中存在的粗大树枝晶α-Al相以及针状共晶Si严重割裂基体,显著降低合金的力学性能。为细化Al-Si合金的组织,提升其力学性能,本文使用扫描电镜(SEM)、电子探针(EPMA)、X射线衍射仪(XRD)以及万能材料试验机,研究了不同添加量Y/Al-5Ti-1B变质剂(Al-5Ti-1B均为2%,稀土Y分别为0.05%、0.1%、0.2%、0.3%、0.4%、0.5%,质量分数)对Al-7Si合金微观组织和力学性能的影响,并探究了其对Al-7Si合金的变质机理。实验结果表明,当Al-5Ti-1B含量为2%、稀土Y含量为0.4%时,变质效果最佳,共晶Si由粗大针状变为细小颗粒状,长和宽分别减小至2.7和0.8μm,相较于未经变质处理的Al-7Si合金,减小了90.6%和4.7%。合金抗拉强度由原来的168.1 MPa提升至209.1 MPa,增加了24.4%。同时伸长率从6.23%提升至9.62%,增长了54.4%。此外,合金的断裂方式也从脆性断裂转变为韧-脆混合断裂。

原位合成Si/(SiO+Ag)复合负极材料及其电化学性能

将微米Si和纳米Ag_(2)O进行机械球磨,通过原位固相反应合成了Si基复合材料[Si/(SiO+Ag)],以沥青为碳源采用高温煅烧法制备了碳包覆Si基复合材料[Si/(SiO+Ag)-C]。采用XRD、XPS、SEM、TEM对复合材料进行了表征,测试了其电化学性能。结果表明,微米Si和纳米Ag_(2)O在球磨破碎过程中原位形成Si O和Ag颗粒,并附着在基体Si上,两种复合材料都展现出良好的倍率性能,在低电流密度(0.12 A/g)下Si/(SiO+Ag)和Si/(SiO+Ag)-C循环5次后分别表现出1422和1039 mA·h/g的可逆比容量,而在高电流密度(2.40 A/g)下仍能获得672和393 mA·h/g的可逆比容量;当电流密度再次恢复到0.12 A/g时,可逆比容量可恢复到1329和961m A·h/g,Si/(SiO+Ag)-C表现出更好的循环稳定性,经80次循环后可逆比容量仍稳定在943 m A·h/g,其突出的倍率性能归因于微米Si的颗粒细化以及球磨过程中原位反应形成纳米Ag颗粒导电特性,而循环稳定性的提高与原位形成Si O和包覆碳构成的双相缓冲结构有关。

表面喷丸及退火处理对Fe-30Mn-3Al-3Si TWIP钢组织与性能的影响

为实现强韧化,对Fe-30Mn-3Al-3Si TWIP钢进行了表面喷丸及退火热处理。采用金相显微镜、X射线衍射仪和透射电子显微镜等手段分析了喷丸以及喷丸结合退火处理对TWIP钢显微组织结构的影响,并利用显微维氏硬度计和万能材料试验机对原始样品、喷丸以及喷丸结合退火处理样品的硬度分布、力学性能及加工硬化行为进行了研究。分析结果表明,喷丸可在TWIP钢表面引起强烈的塑性变形,并形成包含60~100 nm大小的位错胞块的强烈形变层和包含微纳尺度形变孪晶结构的过渡层。该纳米-微米尺度的晶粒尺寸梯度结构可以将TWIP钢表面强烈形变层的硬度显著提升至366 HV0.1,并在残余压应力联合作用下使试样的屈服强度提升至485 MPa,均远高于初始样品的对应值。但受喷丸引起的表面粗糙和强烈形变层纳米晶塑性低的影响,其断后延伸率仅为41.8%。退火处理后,喷丸样品中的形变组织发生回复与再结晶,其中强烈形变层位置的再结晶晶粒尺寸为1~3μm,硬度也降低至215 HV0.1。所形成的微米-微米尺度晶粒尺寸梯度结构试样的屈服强度降低至261 MPa,但延伸率增加至65.3%。晶粒尺寸梯度结构有助于增加TWIP钢屈服与抗拉强度,但不利于延伸率的提升。