Plain concrete is regarded as a two-phase material comprising randomly distributed aggregates and mortar matrix. A series of three-point bending concrete beams with symmetric or asymmetric double notches are modeled u...Plain concrete is regarded as a two-phase material comprising randomly distributed aggregates and mortar matrix. A series of three-point bending concrete beams with symmetric or asymmetric double notches are modeled using the modified random aggregate generation and packing algorithm. The cohesive zone model is used as the fracture criterion and the cohesive el- ements are inserted into both the mortar matrix and the aggregate-mortar interfaces as potential micro-cracking zones. The dead and alive crack phenomena are studied experimentally and nu- merically; and the influences of notch location, aggregate distribution and gradation on fracture are numerically evaluated. Some important conclusions are given.展开更多
304 stainless steel coating was deposited on the IF steel substrate by cold gas dynamic spraying （CGDS）, and the elastic modulus of the 304 stainless steel coating was studied. The elastic modulus of cold sprayed 30...304 stainless steel coating was deposited on the IF steel substrate by cold gas dynamic spraying （CGDS）, and the elastic modulus of the 304 stainless steel coating was studied. The elastic modulus of cold sprayed 304 stain- less steel coating was measured using the three-point bend testing and the compound beam theory, and the other me- chanic parameters （such as the equivalent flexural rigidity and the moment of inertia of area） of the coatings were also calculated using this compound beam theory. It is found that the calculated results using the above methods are accu- rate and reliable. The elastic modulus value of the cold sprayed 304 stainless steel coating is 1. 179 X 105 MPa, and it is slightly lower than the 304 stainless steel plate （about 2 X 105 MPa）. It indicates that the elastic modulus of the cold sprayed coatings was quite different from the comparable bulk materials. The main reason is that the pores and other defects are existed in the coatings, and the elastic modulus of the coatings also depends on varies parameters such as the feed stock particle size, porosity, and processing parameters.展开更多
基金Project supported by the National Basic Research Program of China(973 Program:No.2011CB013800)Hubei Provincial Natural Science Foundation of China(No.2015CFB205)
文摘Plain concrete is regarded as a two-phase material comprising randomly distributed aggregates and mortar matrix. A series of three-point bending concrete beams with symmetric or asymmetric double notches are modeled using the modified random aggregate generation and packing algorithm. The cohesive zone model is used as the fracture criterion and the cohesive el- ements are inserted into both the mortar matrix and the aggregate-mortar interfaces as potential micro-cracking zones. The dead and alive crack phenomena are studied experimentally and nu- merically; and the influences of notch location, aggregate distribution and gradation on fracture are numerically evaluated. Some important conclusions are given.
基金Sponsored by National Natural Foundtion of China(51134013,51171037)
文摘304 stainless steel coating was deposited on the IF steel substrate by cold gas dynamic spraying （CGDS）, and the elastic modulus of the 304 stainless steel coating was studied. The elastic modulus of cold sprayed 304 stain- less steel coating was measured using the three-point bend testing and the compound beam theory, and the other me- chanic parameters （such as the equivalent flexural rigidity and the moment of inertia of area） of the coatings were also calculated using this compound beam theory. It is found that the calculated results using the above methods are accu- rate and reliable. The elastic modulus value of the cold sprayed 304 stainless steel coating is 1. 179 X 105 MPa, and it is slightly lower than the 304 stainless steel plate （about 2 X 105 MPa）. It indicates that the elastic modulus of the cold sprayed coatings was quite different from the comparable bulk materials. The main reason is that the pores and other defects are existed in the coatings, and the elastic modulus of the coatings also depends on varies parameters such as the feed stock particle size, porosity, and processing parameters.
