One of the conventional ways to improve the mechanical behavior of soils is to mix them with cementing agents such as cement, lime and fly ash. Recently, introduction to alternative materials or sub-products that can ...One of the conventional ways to improve the mechanical behavior of soils is to mix them with cementing agents such as cement, lime and fly ash. Recently, introduction to alternative materials or sub-products that can be adopted to improve the soil strength is of paramount importance. Therefore, the present study aims to investigate the effects of porosity(h), dry unit weight(gd) of molding, cement content(C)and porosity/volumetric cement content ratio(h/Civ) or void/cement ratio on the unconfined compressive strength(quor UCS) of silty soileroof tile waste(RT) mixtures. Soil samples are molded into four different dry unit weights(i.e. 13 kN/m^3, 13.67 kN/m^3, 14.33 kN/m^3 and 15 kN/m^3) using 3%, 6% and 9%cement and 5%, 15% and 30% RT. The results show that with the addition of cement, the strength of the RT esoil mixtures increases in a linear manner. On the other hand, the addition of RT decreases quof the samples at a constant percentage of cement, and the decrease in porosity can increase qu. A dosage equation is derived from the experimental data using the porosity/volumetric cement content ratio(h/C_(iv)) where the control variables are the moisture content, crushed tile content, cement content and porosity.展开更多
This paper presents an innovative approach to reusing waste tile granules(TG) and ceramic polishing powder(PP) to produce high performance ceramic tiles.We studied formulations each with a TG mass fraction of 25.0% an...This paper presents an innovative approach to reusing waste tile granules(TG) and ceramic polishing powder(PP) to produce high performance ceramic tiles.We studied formulations each with a TG mass fraction of 25.0% and a different PP mass fraction between 1.0% and 7.0%.The formulations included a small amount of borax additive of a mass fracton between 0.2% and 1.2%.The effects of these industrial by-products on compressive strength,water absorption and microstructure of the new ceramic tiles were investigated.The results indicate that the compressive strength decreases and water absorption increases when TG with a mass fraction of 25.0% are added.Improvement of the compressive strength may be achieved when TG(up to 25.0%) and PP(up to 2.0%) are both used at the same time.In particular,the compressive strength improvement can be maximized and water absorption reduced when a borax additive of up to 0.5% is used as a flux.Scanning electron microscopy reveals that a certain amount of fine PP granules and a high content of fluxing oxides from borax avail the formation of glassy phase that fills up the pores in the new ceramic tiles,resulting in a dense product with high compressive strength and low water absorption.展开更多
文摘One of the conventional ways to improve the mechanical behavior of soils is to mix them with cementing agents such as cement, lime and fly ash. Recently, introduction to alternative materials or sub-products that can be adopted to improve the soil strength is of paramount importance. Therefore, the present study aims to investigate the effects of porosity(h), dry unit weight(gd) of molding, cement content(C)and porosity/volumetric cement content ratio(h/Civ) or void/cement ratio on the unconfined compressive strength(quor UCS) of silty soileroof tile waste(RT) mixtures. Soil samples are molded into four different dry unit weights(i.e. 13 kN/m^3, 13.67 kN/m^3, 14.33 kN/m^3 and 15 kN/m^3) using 3%, 6% and 9%cement and 5%, 15% and 30% RT. The results show that with the addition of cement, the strength of the RT esoil mixtures increases in a linear manner. On the other hand, the addition of RT decreases quof the samples at a constant percentage of cement, and the decrease in porosity can increase qu. A dosage equation is derived from the experimental data using the porosity/volumetric cement content ratio(h/C_(iv)) where the control variables are the moisture content, crushed tile content, cement content and porosity.
基金Funded by a grant from the Key Technologies R & D Program of Guangzhou (No. 2004440003110013)
文摘This paper presents an innovative approach to reusing waste tile granules(TG) and ceramic polishing powder(PP) to produce high performance ceramic tiles.We studied formulations each with a TG mass fraction of 25.0% and a different PP mass fraction between 1.0% and 7.0%.The formulations included a small amount of borax additive of a mass fracton between 0.2% and 1.2%.The effects of these industrial by-products on compressive strength,water absorption and microstructure of the new ceramic tiles were investigated.The results indicate that the compressive strength decreases and water absorption increases when TG with a mass fraction of 25.0% are added.Improvement of the compressive strength may be achieved when TG(up to 25.0%) and PP(up to 2.0%) are both used at the same time.In particular,the compressive strength improvement can be maximized and water absorption reduced when a borax additive of up to 0.5% is used as a flux.Scanning electron microscopy reveals that a certain amount of fine PP granules and a high content of fluxing oxides from borax avail the formation of glassy phase that fills up the pores in the new ceramic tiles,resulting in a dense product with high compressive strength and low water absorption.
