Comparison between Response Spectrum and Time History Method of Dynamic Analysis of Concrete Gravity Dam

Dam structure built to store water has failed with resulting loss of life, social, economic and environmental losses due to seismic vibrations. These vibrations are dynamic in nature. These vibrations must be reduced with proper application of engineering principles and for estimating the behavior of concrete gravity dam dynamic analysis plays an extraordinary role. This paper presents the dynamic time history analysis and response spectrum method of a concrete gravity dam by using STAAD-PRO. Here Finite Element Approach is used to analyze the dam. A concrete gravity dam model is prepared in STAAD-PRO to perform the time history analysis and response spectrum analysis and a comparison is done between both these methods. Concrete gravity dam is a large structure which retains a very large amount of water on its upstream side and it is very crucial for a dam to survive against vibrations of earthquake. So it is a matter of study to check the behaviour of a dam during and after the application of the loading.

Coseismic site response and slope instability using periodic boundary conditions in the material point method

This paper proposed the explicit generalized-a time scheme and periodic boundary conditions in the material point method(MPM)for the simulation of coseismic site response.The proposed boundary condition uses an intuitive particle-relocation algorithm ensuring material points always remain within the computational mesh.The explicit generalized-a time scheme was implemented in MPM to enable the damping of spurious high frequency oscillations.Firstly,the MPM was verified against finite element method(FEM).Secondly,ability of the MPM in capturing the analytical transfer function was investigated.Thirdly,a symmetric embankment was adopted to investigate the effects of ground motion arias intensity(I_(a)),geometry dimensions,and constitutive models.The results show that the larger the model size,the higher the crest runout and settlement for the same ground motion.When using a Mohr-Coulomb model,the crest runout increases with increasing I_(a).However,if the strain-softening law is activated,the results are less influenced by the ground motion.Finally,the MPM results were compared with the Newmark sliding block solution.The simplified analysis herein highlights the capabilities of MPM to capture the full deformation process for earthquake engineering applications,the importance of geometry characterization,and the selection of appropriate constitutive models when simulating coseismic site response and subsequent large deformations.

Time history of seismic earth pressure response from gravity retaining wall based on energy dissipation

The seismic design of gravity retaining walls is based mostly on the pseudo static method.The seismic earth pressure is assumed to be a constant without considering the wave traveling effect when the seismic wave propagates through the slope.However,under continuous ground motion,the actual earth pressure on the retaining wall varies with time.The present seismic earth pressure calculation method yields results that differ significantly from the actual scenario.Considering this,a slip surface curve was assumed in this study.It is more suitable for engineering practice.In addition,a theoretical calculation model based on energy dissipation was established.The time history of seismic earth pressure response under continuous ground motion was calculated using the equilibrium equation between the external power and the internal energy dissipation power of the sliding soil wedge.It can more effectively reflect the stress scenario of a retaining wall under seismic conditions.To verify the applicability of the proposed approach,a large-scale shaking table test was conducted,and the time history of the seismic earth pressure response obtained from the experiment was compared with the calculation results.The results show that the proposed approach is applicable to the calculation of the time history of seismic earth pressure response of gravity retaining walls.This lays the foundation for the seismic design of retaining structures by using dynamic time history.

Generation of Time History Compatible with Multi-Damping Response Spectra

Based on the method developed by M. Hirasawa and M. Watabe (1992), the authors deduced the related mathematical formulas. Taking an artificial ground motion compatible with single-damping as the original time history, a small corrected time history was calculated by solving linear equations using a singular value decomposition method. We performed iteration to obtain the simulated earthquake motion compatible with multi-damping within a certain accuracy. The influences of selective matching frequencies are discussed preliminarily. Although the current criterion still has no explicit demand on different numbers of matching frequencies for various damping factors, it should be taken into account in practice.

Electromagnetic response function for the semi-annual variations estimated by the single-station method using the night-time values of the geomagnetic fields

The geomagnetic night-time values were used to estimate the electromagnetic response function Q1 for half-year period. If the spatial structure of the source field can be described by the approximation, one can estimate the Q1 value using the single-station Z/H method. This technique enables us to carry out regional deep gcomagnetic sounding by the method. The data used for analyses are geomagnetic night-time values for about, typically, 26 years from 5 good-quality stations and for several years from 34 stations distributed over the globe. The results indicate that the night-time values yield more reliable response estimates for half-year period compared to the usual estimates obtained from daily means. It implies that the approximation for the night-time fields holds good for the half-year period, but the daily means are not suitable for estimating the response function of the semi-annual variations by using the single-station method. Source field analyses for daily means data and night-time means data have also been carried out in this paper.

Harmonic balance method with alternating frequency/time domain technique for nonlinear dynamical system with fractional exponential

Comparisons of the common methods for obtaining the periodic responses show that the harmonic balance method with alternating frequency/time （HB-AFT） do- main technique has some advantages in dealing with nonlinear problems of fractional exponential models. By the HB-AFT method, a rigid rotor supported by ball bearings with nonlinearity of Hertz contact and ball passage vibrations is considered. With the aid of the Floquet theory, the movement characteristics of interval stability are deeply studied. Besides, a simple strategy to determine the monodromy matrix is proposed for the stability analysis.

Time Domain Simulation of Transient Responses of Very Large Floating Structures Under Unsteady External Loads

A time domain finite element method （FEM） for the analysis of transient elastic response of a very large floating structure （VLFS） subjected to arbitrary time-dependent external loads is presented. This method is developed directly in time domain and the hydrodynamic problem is formulated based on linear, inviscid and slightly compressible fluid theory and the structural response is analyzed on the thin plate assumption. The time domain finite element procedure herein is validated by comparing numerical results with available experimental data. Finally, the transient elastic response of a pontoon-type VLFS under the landing of an airplane is computed by the proposed time domain FEM. The time histories of the applied force and the position and velocity of an airplane during landing are modeled with data from a Boeing 747-400 jumbo jet.

Efficient structural seismic performance evaluation method using improved endurance time analysis

Evaluation of structural performance under seismic excitations from low intensity to high intensity is essential to verify the seismic resistant capacity of a structure, and usually carried out by the incremental dynamic analysis (IDA) method or pushover method. The recently developed endurance time (ET) method is another method that uses dynamic pushover excitations, i.e., endurance time acceleration function, to obtain results similar to those obtained by IDA or pushover methods with low computational cost and acceptable accuracy. This study proposes an improvement on the ET method by considering more restrictions for both the elastic and inelastic response spectra in the generation procedure, and by specifying a target duration. Four reinforced concrete frame structures with 4, 8, 12, and 16 stories are adopted to verify the accuracy of the improved method. Comparison of the results obtained by the proposed method, the ET method and the IDA method shows that the improved method has a higher accuracy than the ET method. For evaluation of structural responses under specifi c ground motion intensity, which is typically required in seismic design codes, the results obtained by the proposed method are compared with fi ve commonly used ground motion selection methods, and shows the proposed method provides acceptable accuracy for engineering applications.

Dynamic interaction numerical models in the time domain based on the high performance scaled boundary finite element method

Consideration of structure-foundation-soil dynamic interaction is a basic requirement in the evaluation of the seismic safety of nuclear power facilities. An efficient and accurate dynamic interaction numerical model in the time domain has become an important topic of current research. In this study, the scaled boundary finite element method （SBFEM） is improved for use as an effective numerical approach with good application prospects. This method has several advantages, including dimensionality reduction, accuracy of the radial analytical solution, and unlike other boundary element methods, it does not require a fundamental solution. This study focuses on establishing a high performance scaled boundary finite element interaction analysis model in the time domain based on the acceleration unit-impulse response matrix, in which several new solution techniques, such as a dimensionless method to solve the interaction force, are applied to improve the numerical stability of the actual soil parameters and reduce the amount of calculation. Finally, the feasibility of the time domain methods are illustrated by the response of the nuclear power structure and the accuracy of the algorithms are dynamically verified by comparison with the refinement of a large-scale viscoelastic soil model.

Finite Difference Solution of Response Time Delay of Magneto-rhelological Damper

Magneto-rhelological（MR） dampers are devices that employ rheological fluids to modify their mechanical properties. Their mechanical simplicity, high dynamic range, lower power requirements, large force capacity, robustness and safe maimer of operation in cases of failure have made them attractive devices for semi-active real-time control in civil, aerospace and automotive applications. Time response characteristic is one of the most important technical performances of MR dampers, and response time directly affects the control frequency, application range and the actual effect of MR dampers. In this study, one kind of finite difference solution for predicting the response time ofmagneto-rheological dampers from ＂off-state＂ to ＂on-state＂ is put forward. A laminar flow model is used to describe the flow in the MR valve, and a bi-viscous fluid flow model is utilized to describe the relationship of shear stress and shear rate of MR fluid. An explicit difference format is used to diseretize the Novior-Stoks equation, and stability condition of this algorithm is built by Von-Neumann stability criterion. The pressure gradient along the flow duct is solved by a dichotomy algorithm with iteration, and the changing curve of the damping force versus time of MR damper is obtained as well. According to the abovementioned numerical algorithm, the damping forces versus time curves from ＂off-state＂ to ＂on-state＂ of a cylindrical piston type MR damper are computed. Moreover, the MR damper is installed in a material test system（MTS）, the magnetic field in the wire circles of the MR damper is ＂triggered＂ when the MR damper is imposed to do a constant speed motion, and the damping force curves are recorded. The comparison between numerical results and experimental results indicates that this finite difference algorithm can be used to estimate the response time delay of MR dampers.

Long-term deformation analysis of Shuibuya concrete face rockfill dam based on response surface method and improved genetic algorithm

Due to the size effects of rockfill materials, the settlement difference between numerical simulation and in situ monitoring of rockfill dams is a topic of general concern.The constitutive model parameters obtained from laboratory triaxial tests often underestimate the deformation of high rockfill dams.Therefore, constitutive model parameters obtained by back analysis were used to calculate and predict the long-term deformation of rockfill dams.Instead of using artificial neural networks (ANNs), the response surface method (RSM) was employed to replace the finite element simulation used in the optimization iteration.Only 27 training samples were required for RSM, improving computational efficiency compared with ANN, which required 300 training samples.RSM can be used to describe the relationship between the constitutive model parameters and dam settlements.The inversion results of the Shuibuya concrete face rockfill dam (CFRD) show that the calculated settlements agree with the measured data, indicating the accuracy and efficiency of RSM.

Numerical Calculation Methods for Wavemaking Response Induced by Explosion in Harbour

Using the axial symmetry results of marker and cell (MAC) method as initial value in this paper, two numerical calculating methods are presented for the late wavemaking response induced by explosion in harbour. One of the methods is the superposition method of the vibration mode based on fluid slosh in container. Another one is the joining method of the MAC results with the shallow wave theory calculation in time domain. As a practical example, it is conducted to the numerical calculation about 1000 ton TNT equivalent explosion within touch of water surface. The results show that it can be rationally described with the methods to the wavemaking progress and character. The numerical results are identical with the observed scene on the spot experiment. The methods are simple and applicable in the engineering design.

Frequency response range of terahertz pulse coherent detection based on THz-induced time-resolved luminescence quenching

It has been proposed previously that the coherent detection of a terahertz（THz） pulse can be achieved based on the time-resolved luminescence quenching. In this paper, we investigate the frequency response range of this novel detection technology by simulating the motion of carriers in gallium arsenide（GaAs） by the ensemble Monte Carlo method. At room temperature, for a direct-current（DC） voltage of 20 kV/cm applied to the semiconductor（GaAs） and sampling time o140 fs, the luminescence quenching phenomena induced by terahertz pulses with different center frequencies are studied The results show that the quenching efficiency is independent of the THz frequency when the frequency is in a range o0.1 THz–4 THz. However, when the frequency exceeds 4 THz, the efficiency decreases with the increase of frequency Therefore, the frequency response range is 0.1 THz–4 THz. Moreover, when the sampling time is changed to 100 fs the frequency response range is extended to be approximately 0.1 THz–5.6 THz. This study of the frequency-dependen characteristics of the luminescence response to the THz pulse can provide a theoretical basis for the exploration of THz detection technology.

A Real-Time Transient Analysis of a Functionally Graded Material Plate Using Reduced-Basis Methods

Based on the hybrid numerical method (HNM) combining with a reduced-basis method (RBM), the real-time transient response of a functionally graded material (FGM) plates is obtained. The large eigenvalue problem in wavenumber domain has been solved through real-time off-line/on-line calculation. At off-line stage, a reduced-basis space is constructed in sample wavenumbers according to the solved eigenvalue problems. The matrices independent of parameters are projected onto the reduced-basis spaces. At on-line stage, the reduced eigenvalue problems of the arbitrary wavenumbers are built. Subsequently, the responses in wavenumber domain are obtained by the approximated eigen-pairs. Because of the application of RBM, the computational cost of transient displacement analysis of FGM plate is decreased significantly, while the accuracy of the solution and the physics of the structure are still retained. The efficiency and validity of the proposed method are demonstrated through a numerical example.

Generation and Application of A Standardized Load-Time History to Tubular T-joints in Offshore Platforms

Marine structures are mostly made of metals and always experience complex random loading during their service periods. The fatigue crack growth behaviors of metal materials have been proved from laboratory tests to be sensitive to the loading sequence encountered. In order to take account of the loading sequence effect, fatigue life prediction should be based on fatigue crack propagation（FCP） theory rather than the currently used cumulative fatigue damage（CFD） theory. A unified fatigue life prediction（UFLP） method for marine structures has been proposed by the authors＇ group. In order to apply the UFLP method for newly designed structures, authorities such as the classification societies should provide a standardized load-time history（SLH） such as the TWIST and FALSTAFF sequences for transport and fighter aircraft. This paper mainly aims at proposing a procedure to generate the SLHs for marine structures based on a short-term loading sample and to provide an illustration on how to use the presented SLH to a typical tubular T-joint in an offshore platform based on the UFLP method.

基于时程分析法的中美隔震设计对比研究

介绍了中国《建筑隔震设计标准》(GB/T 51408—2021)(以下简称《隔标》)和美国Minimum design loads and associated criteria for buildings and other structures(ASCE 7-16)隔震设计的相关要求,并针对基于《建筑抗震设计规范》(GB 50011—2010)(2016年版)(以下简称《抗规》)设计的某9度区近场隔震结构,进行了两国规范的设计对比。按《抗规》设计的隔震结构,仍然能满足《隔标》的设计要求。ASCE 7-16对于隔震支座考虑了老化和环境、测试、制造等因素引起的性能参数变化,并按隔震支座的上限及下限属性进行了结构设计。基于相同地震概率水准(50年超越概率2%)的设计对比研究表明,ASCE 7-16的等效侧力法计算值高于《隔标》,按ASCE 7-16要求选择的地震波反应谱明显高于《隔标》,其时程分析结果也大于中国规范,对隔震支座的性能要求更高。

地震动持时和不同持时指标对结构地震响应的影响

选取70条具有不同持时的天然地震波,并采用5%~75%重要持时将谱匹配后的地震记录划分为长、短持时地震记录集,对10层RC框架结构进行IDA分析和弹塑性时程分析,研究地震动持时对结构地震响应的影响,进一步选取35条天然地震波,采用有效持续时间、5%~75%和5%~95%重要持时等不同强震持时指标分别截取相应的加速度时程段,构建不同的地震记录集,分析不同持时指标对RC框架结构峰值响应和滞回耗能的影响。研究结果表明:在相同的地震动强度下,长持时地震动会导致更大的结构层间变形和结构倒塌概率,且随着持时的增加,结构总滞回耗能大幅增加;在罕遇地震水准下,可选取有效持续时间和5%~95%重要持时指标用于结构层间变形和楼层峰值位移分析,而在极罕遇地震水准下,选用有效持续时间具有更高的可靠性;对于楼层峰值速度,不同地震集计算结果均值和变异系数未表现出明显差异;在相同地震动强度下,建议优先选用有效持续时间用于结构滞回耗能分析。

气体辅助注射成型时间参数的CCD响应面法多目标优化

相比于传统塑料注射成型,延迟时长和注气时长是气体辅助注射成型(简称气辅成型)特有的工艺参数,增加了气辅成型的复杂性。为了精确设计延迟时长和注气时长的取值,获得理想的气体穿透效果和气指幅度,以具有典型气辅结构的塑件为研究对象,首先采用气辅成型全三维CAE研究了延迟时长和注气时长对气辅成型质量的影响。结果表明,适当增加延迟时长,可以减小或消除气指缺陷,提高气体穿透深度行程,但过长的延迟时长会导致“短射”,过短的延迟时长则会导致严重的气指缺陷;增加注气时长可以提高气体穿透效果,减少表面缺陷,降低内应力和翘曲变形,但注气时长过长时,气指内部的高压氮气会导致其撕裂而形成严重的气指缺陷,更甚者会使气辅塑件膨胀而报废。采用CCD响应面法进行多目标优化,精确设计了延迟时长和注气时长的取值,延迟时长为4 s、注气时长为10.37 s。通过CAE分析和成型试验验证,精确取值下成型的气辅塑件的气体穿透效果和气辅成型质量良好,提高了气辅成型质量和效率,可用于气辅成型实际生产。

盐渍土环境下考虑耐久性损伤的输电塔风振时程分析

长期服役于盐渍土环境下的输电塔耐久性损伤较为严重,当其材料力学性能退化到一定程度时,在强风作用下,输电塔可能会发生破坏,危害线路的安全运行。基于±800kV天中线特高压直流输电工程直线塔,考虑基础钢筋锈蚀、基础混凝土侵蚀、输电塔杆塔钢材锈蚀以及基础箍筋的约束效应,在ABAQUS有限元软件中建立塔-线-基础耦合模型,研究不同风攻角和材料耐久性损伤对塔身动力响应的影响。结果表明:90°风攻角下塔身顺风向位移最大,为最不利风向基本工况;90°风攻角下输电塔塔顶顺风向位移响应贡献主要以背景分量为主,但共振分量也有一定贡献,主要以输电塔1阶振型频率为主,且随着服役时间的增加,振型频率逐渐降低,相应响应的贡献程度逐渐提高;相同风荷载作用下,随着服役时间的增加,塔身位移逐渐增大,相同服役时间下,随着塔身高度的增加,塔身位移响应峰值增长速度变快,结构振动更加明显,材料耐久性损伤对输电塔的位移响应影响较大。