Numerical Analysis on Temperature Distribution in a Single Cell of PEFC Operated at Higher Temperature by1D Heat Transfer Model and 3D Multi-Physics Simulation Model

This study is to understand the impact of operating conditions, especially initial operation temperature (Tini) which is set in a high temperature range, on the temperature profile of the interface between the polymer electrolyte membrane (PEM) and the catalyst layer at the cathode (i.e., the reaction surface) in a single cell of polymer electrolyte fuel cell (PEFC). A 1D multi-plate heat transfer model based on the temperature data of the separator measured using the thermograph in a power generation experiment was developed to evaluate the reaction surface temperature (Treact). In addition, to validate the proposed heat transfer model, Treact obtained from the model was compared with that from the 3D numerical simulation using CFD software COMSOL Multiphysics which solves the continuity equation, Brinkman equation, Maxwell-Stefan equation, Butler-Volmer equation as well as heat transfer equation. As a result, the temperature gap between the results obtained by 1D heat transfer model and those obtained by 3D numerical simulation is below approximately 0.5 K. The simulation results show the change in the molar concentration of O2 and H2O from the inlet to the outlet is more even with the increase in Tini due to the lower performance of O2 reduction reaction. The change in the current density from the inlet to the outlet is more even with the increase in Tini and the value of current density is smaller with the increase in Tini due to the increase in ohmic over-potential and concentration over-potential. It is revealed that the change in Treact from the inlet to the outlet is more even with the increase in Tini irrespective of heat transfer model. This is because the generated heat from the power generation is lower with the increase in Tini due to the lower performance of O2 reduction reaction.

Temperature characterizations of silica asymmetric Mach–Zehnder interferometer chip for quantum key distribution

Quantum key distribution(QKD)system based on passive silica planar lightwave circuit(PLC)asymmetric Mach–Zehnder interferometers(AMZI)is characterized with thermal stability,low loss and sufficient integration scalability.However,waveguide stresses,both intrinsic and temperature-induced stresses,have significant impacts on the stable operation of the system.We have designed silica AMZI chips of 400 ps delay,with bend waveguides length equalized for both long and short arms to balance the stresses thereof.The temperature characteristics of the silica PLC AMZI chip are studied.The interference visibility at the single photon level is kept higher than 95%over a wide temperature range of 12℃.The delay time change is 0.321 ps within a temperature change of 40℃.The spectral shift is 0.0011 nm/0.1℃.Temperature-induced delay time and peak wavelength variations do not affect the interference visibility.The experiment results demonstrate the advantage of being tolerant to chip temperature fluctuations.

The Influence of Climate Change and Variability on Spatio-Temporal Rainfall and Temperature Distribution in Zanzibar

Climate change has resulted in serious social-economic ramifications and extremely catastrophic weather events in the world, Tanzania and Zanzibar in particular, with adaptation being the only option to reduce impacts. The study focuses on the influence of climate change and variability on spatio-temporal rainfall and temperature variability and distribution in Zanzibar. The station observation datasets of rainfall, Tmax and Tmin acquired from Tanzania Meteorological Authority (TMA) and the Coordinated Regional Climate Downscaling Experiment program (CORDEX) projected datasets from the Regional climate model HIRHAM5 under driving model ICHEC-EC-EARH, for the three periods of 1991-2020 used as baseline (HS), 2021-2050 as near future (NF) and 2051-2080 far future (FF), under two representative concentration pathways (RCP) of 4.5 and 8.5, were used. The long-term observed Tmax and Tmin were used to produce time series for observing the nature and trends, while the observed rainfall data was used for understanding wet and dry periods, trends and slope (at p ≤ 0.05) using the Standardized Precipitation Index (SPI) and the Mann Kendall test (MK). Moreover, the Quantum Geographic Information System (QGIS) under the Inverse Distance Weighting (IDW) interpolation techniques were used for mapping the three decades of 1991-2000 (hereafter D1), 2001-2010 (hereafter D2) and 2011-2020 (hereafter D3) to analyze periodical spatial rainfall distribution in Zanzibar. As for the projected datasets the Climate Data Operator Commands (CDO), python scripts and Grid analysis and Display System (GrADS) soft-wares were used to process and display the results of the projected datasets of rainfall, Tmax and Tmin for the HS, NF and FF, respectively. The results show that the observed Tmax increased by the rates of 0.035℃ yr-1 and 0.0169℃ yr-1, while the Tmin was increased by a rate of 0.064℃ yr-1 and 0.104℃ yr-1 for Unguja and Pemba, respectively. The temporal distribution of wetness and dryness indices showed a climate shift from near normal to moderate wet during 2005 at Zanzibar Airport, while normal to moderately dry conditions, were observed in Pemba at Matangatuani. The decadal rainfall variability and distributions revealed higher rainfall intensity with an increasing trend and good spatial distribution in D3 from March to May (MAM) and October to December (OND). The projected results for Tmax during MAM and OND depicted higher values ranging from 1.7℃ - 1.8℃ to 1.9℃ - 2.0℃ and 1.5℃ to 2.0℃ in FF compared to NF under both RCPs. Also, higher Tmin values of 1.12℃ - 1.16℃ was projected in FF for MAM and OND under both RCPs. Besides, the rainfall projection generally revealed increased rainfall intensity in the range of 0 - 25 mm for Pemba and declined rainfall in the range of 25 - 50 mm in Unguja under both RCPs in perspectives of both NF and FF. Conclusively the study has shown that the undergoing climate change has posed a significant impact on both rainfall and temperature spatial and temporal distributions in Zanzibar (Unguja and Pemba), with Unguja being projected to have higher rainfall deficits while increasing rainfall strengths in Pemba. Thus, the study calls for more studies and formulation of effective adaptation, strategies and resilience mechanisms to combat the projected climate change impacts especially in the agricultural sector, water and food security.

Numerical simulation of downhole temperature distribution in producing oil wells

An improved numerical simulation method is presented to calculate the downhole temperature distribution for multiple pay zones in producing oil wells. Based on hydrodynamics and heat transfer theory, a 2-D temperature field model in cylindrical coordinates is developed. In the model, we considered general heat conduction as well as the heat convection due to fluid flow from porous formation to the borehole. We also take into account the fluid velocity variation in the wellbore due to multiple pay zones. We present coupled boundary conditions at the interfaces between the wellbore and adjacent formation, the wellbore and pay zone, and the pay zone and adjacent formation. Finally, an alternating direction implicit difference method （ADI） is used to solve the temperature model for the downhole temperature distribution. The comparison of modeled temperature curve with actual temperature log indicates that simulation result is in general quite similar to the actual temperature log. We found that the total production rate, production time, porosity, thickness of pay zones, and geothermal gradient, all have effects on the downhole temperature distribution.

On the Thermal Distribution in Oncological Hyperthermia Treatments

The temperature is one of the principal controlling parameters of oncological hyperthermia. However, local heating forms a complicated thermal distribution in space and has developed over time, too. The decisional factors are the heterogeneity of the targeted volume, the electrolyte perfusions controlled by thermal homeostasis, and the spreading of the heat energy with time. A further complication is that the energy absorption sharply changes by depth, so the spatiotemporal development of the temperature distribution requires specialized methods to control. Most of the temperature imaging facilities (thermography, radiometry, electric impedance tomography, etc.) are less precise than the medical practice needs. In contrast, precise point sensing (like thermocouples, thermistors, and fluoroptical methods) is invasive and measures only a discrete point in the robustly changing thermal map. The two most precise thermal imaging methods, computer tomography, and magnetic resonance are expensive and have numerous technical complications. Our objective is to show the complexity of the temperature distribution inside the human body, and offer a relatively simple and cheap method to visualize its spatiotemporal development. A novel emerging technology, the application of ultrasound microbubble contrast agents is a promising method for solving complicated tasks of thermal distribution deep inside the living body. Noteworthy, the temperature distribution does not determine the full hyperthermia process, nonthermal effects make considerable impact, too. Additionally to the difficulties to measure the thermal heterogeneity during hyperthermia in oncology, numerous nonthermal processes, molecular and structural changes are triggered by the incoming electromagnetic energy, which presently has no spatiotemporal visualization technique. Microbubble imaging has a suitable spatiotemporal thermal resolution, and also it is sensitive to nonthermal effects. Its application for characterization of the modulated electrohyperthermia (mEHT) may open a new theranostic facility, using the synergy of the thermal and nonthermal effects of the radiofrequency delivered energy. This complex approach gives facility to follow the mEHT processes, and the proposed microbubble ultrasound imaging has a particularly promising advantage sensing and acting also nonthermally, having potential to characterize the thermally conditioned nonthermal electromagnetic effects in oncologic hyperthermia. The mEHT combined with microbubble ultrasound images could be a robust theranostic method against cancer.

Thermal integrity profiling of cast-in-situ piles in sand using fiber-optic distributed temperature sensing

Defects in cast-in-situ piles have an adverse impact on load transfer at the pile‒soil interface and pile bearing capacity. In recent years, thermal integrity profiling (TIP) has been developed to measure temperature profiles of cast-in-situ piles, enabling the detection of structural defects or anomalies at the early stage of construction. However, using this integrity testing method to evaluate potential defects in cast-in-situ piles requires a comprehensive understanding of the mechanism of hydration heat transfer from piles to surrounding soils. In this study, small-scale model tests were conducted in laboratory to investigate the performance of TIP in detecting pile integrity. Fiber-optic distributed temperature sensing (DTS) technology was used to monitor detailed temperature variations along model piles in sand. Additionally, sensors were installed in sand to measure water content and matric suction. An interpretation method against available DTS-based thermal profiles was proposed to reveal the potential defective regions. It shows that the temperature difference between normal and defective piles is more obvious in wet sand. In addition, there is a critical zone of water migration in sand due to the water absorption behavior of cement and temperature transfer-induced water migration in the early-age concrete setting. These findings could provide important insight into the improvement of the TIP testing method for field applications.

Analysis on the Spatial and Temporal Distribution of Extremely Maximum Temperature in Liaoning Province Based on REOF

By selecting the daily maximum temperatures during 1961-2005 in 35 representative stations in Liaoning Province, the temporal and spatial distribution characteristics of extremely maximum temperature event were studied. By using REOF, the mean-square deviation and so on, the variation and distribution situation of extremely maximum temperature in the different regions of Liaoning were reflected. The results showed that the extremely maximum temperature in Liaoning Province could be divided into 3 regions where were respectively the northeast area, the west and the northwest area, the south and the southeast area. The distribution characteristic of extremely maximum temperature threshold value in Liaoning Province was basically consistent with the distribution characteristic of average temperature. The zone where the extremely maximum temperature threshold was relatively high was in the northwest area of Liaoning, and the low threshold zone was in the southeast area and most areas in the east. The variation of extremely maximum temperature in winter was the greatest and in summer was the smallest. The variation of extremely maximum temperature days was the greatest in summer and wasn’t great in spring, autumn, winter.

Spatial distribution of air temperature and relative humidity in the greenhouse as affected by external shading in arid climates

The effect of external roof shading on the spatial distribution of air temperature and relative humidity in a greenhouse(Tin and RHin) was evaluated under the arid climatic conditions of Riyadh City, Saudi Arabia. Two identical, evaporatively-cooled, single-span greenhouses were used in the experiment. One greenhouse was externally shaded(Gs) using a movable black plastic net(30% transmissivity), and the other greenhouse was kept without shading(Gc). Strawberry plants were cultivated in both greenhouses. The results showed that the spatial distribution of the Tin and RHin was significantly affected by the outside solar radiation and evaporative cooling operation. The regression analysis showed that when the outside solar radiation intensity increased from 200 to 800 W m–2, the Tin increased by 4.5℃ in the Gc and 2℃in the Gs, while the RHin decreased by 15% in the Gc and 5% in the Gs, respectively. Compared with those in the Gc, more uniformity in the spatial distribution of the Tin and RHin was observed in the Gs. The difference between the maximum and minimum Tin of 6.4℃ and the RHin of 10% was lower in the Gs than those in the Gc during the early morning. Around 2℃ difference in the Tin was shown between the area closed to the exhausted fans and the area closed to the cooling pad with the external shading. In an evaporatively-cooled greenhouse in arid regions, the variation of the Tin and RHin in the vertical direction and along the sidewalls was much higher than that in the horizontal direction. The average variation of the Tin and RHin in the vertical direction was 5.2℃ and 10% in the Gc and 5.5℃ and 13% in the Gs, respectively. The external shading improved the spatial distribution of the Tin and RHin and improved the cooling efficiency of the evaporative cooling system by 12%, since the transmitted solar radiation and accumulated thermal energy in the greenhouse were significantly reduced.

Study of Temperature Distribution Along an Artificially Polluted Insulator String

Insulator becomes wet partially or completely, and the pollution layer on itbecomes conductive, when collecting pollutants for an extended period during dew, light rain, mist,fog or snow melting. Heavy rain is a complicated factor that it may wash away the pollution layerwithout initiating other stages of breakdown or it may bridge the gaps between sheds to promoteflashover. The insulator with a conducting pollution layer being energized, can cause a surfaceleakage current to flow (also temperature-rise). As the surface conductivity is non-uniform, theconducting pollution layer becomes broken by dry bands (at spots of high current density),interrupting the flow of leakage current. Voltage across insulator gets concentrated across drybands, and causes high electric stress and breakdown (dry band arcing). If the resistance of theinsulator surface is sufficiently low, the dry band arcs can be propagated to bridge the terminalscausing flashover. The present paper concerns the evaluation of the temperature distribution alongthe surface of an energized artificially polluted insulator string.

Temperature distribution study during the friction stir welding process of Al2024-T3 aluminum alloy

Heat flux characteristics are critical to good quality welding obtained in the important engineering alloy A12024- T3 by the friction stir welding （FSW） process. In the present study, thermocouples in three different configurations were amxed on the welding samples to measure the temperatures： in the first configuration, four thermocouples were placed at equivalent positions along one side of the welding direction; the second configuration involved two equivalent thermocouple locations on either side of the welding path; while the third configuration had all the thermocouples on one side of the layout but with unequal gaps from the welding line. A three-dimensional, non-linear ANSYS computational model, based on an approach applied to A12024-T3 for the first time, was used to simulate the welding temperature profiles obtained experimentally. The experimental thermal profiles on the whole were found to be in agreement with those calculated by the ANSYS model. The broad agreement between the two kinds of profiles validates the basis for derivation of the simulation model and provides an approach for the FSW simulation in A12024-T3 and is potentially more useful than models derived previously.

Numerical simulation of 80 ℃ temperature field distribution of thick plate multi-pass welding with SYSWELD

The PPG PITT-CHAR XP flame retardant system has been used by COOEC to preventing the thermal softening of steel in the high temperature,whose degradation temperature is 80 ℃.To prevent damage to PPG PITT-CHAR XP fire retardant paint from excessive heat during welding,it is necessary to get accurately reserved area near the welding joints prior to welding. For the foregoing reasons,the 80 ℃ temperature field distribution of thick plate multi-pass welding was analyzed with SYSWELD.The influence of welding groove form and time interval on welding temperature field was also analyzed. Results showed that the range of 80 ℃ welding temperature field increased with the increasing of weld layers at first and then it inclined to stable value. Interpass time setting was crucial to control the range of 80 ℃ welding temperature field. It was also found that double V groove had better thermal diffusivity than double-bevel groove.And double-bevel groove was better than single V groove.

Temperature Distribution and Scuffing of Tapered Roller Bearing

In the field of aerospace, high-speed trains and automobile, etc, analysis of temperature filed and scuffing failure of tapered roller bearings are more important than ever, and the scuffing failure of elements of such rolling bearings under heavy load and high speed still cannot be effectively predicted yet. A simplified model of tapered roller bearings consisted of one inner raceway, one outer raceway and a tapered roller was established, in which the interaction of several heat sources is ignored. The contact mechanics model, temperature model and model of scuffing failure are synthesized, and the corresponding computer programs are developed to analyze the effects of bearings parameters, different material and operational conditions on thermal performance of bearings, and temperature distribution and the possibility of surface scuffing are obtained. The results show that load, speed, thermal conductivity and tapered roller materials influence temperature rise and scuffing failure of bearings. Ceramic material of tapered roller results in the decrease of scuffing possibility of bearings to a high extent than the conventional rolling bearing steel. Compared with bulk temperature, flash temperature on the surfaces of bearing elements has a little influence on maximum temperature rise of bearing elements. For the rolling bearings operated under high speed and heavy load, this paper proposes a method which can accurately calculate the possibility of scuffing failure of rolling bearings.

Effect of contact thermal resistance on temperature distributions of concrete-filled steel tubes in fire

To predicate the temperature distribution of concrete-filled steel tubes(CFSTs) being exposure to fire,a finite element analysis model was developed using a finite element package,ANSYS.A suggested value of contact thermal resistance was therefore proposed with the supporting of massive numbers of collected test data.Parametric analysis was conducted subsequently towards the cross-sectional temperature distribution of CFST columns in four-side fire,in which the exposure time,width of the cross section,steel ratio were taken into account with considering contact thermal resistance.It was found that contact thermal resistance has little effect on the overall temperature regulation with the exposure time,the width of cross-section or the change of steel ratio.However,great temperature dropping at the concrete adjacent to the contact interface,and gentle temperature increase at steel tube,exist if considering contact thermal resistance.The results of the study are expected to provide theoretical basis for the fire resistance behavior and design of the CFST columns being exposure to fire.

Finite Element Analysis of the Temperature Distribution in Orthogonal Metal Machining

Aim To Research the temperature distribution in orthogonal metal machining and to build a finite element analysis model about the temperature distribution. Methods With the finite element method of thermal conduction, the temperature distributions in various machining conditions were computed according to the experimental data such as cutting force, shear angle, etc. Results The computational results agree with some classic experimental results, and thermal effect due to process parameters was observed. Conclusion The finite element analysis model is reasonable, and it's a feasible scheme for studying the temperature distribution in orthogonal metal machining system.

Microstructure and Temperature Distribution in ZnAl_2O_4 Sintered Body by Pulse Electric Current

Microstructure of reaction sintering of ZnAl2O4 at 1500℃ by hot-pressing(HP) and pulse electric current was investigated. The results indicated that the existed cracks in sintered body were caused by structure mismatch. It is the evidence that periodical temperature field existed during pulse electric current sintering of nonconductive materials. The distance between high temperature areas was related to die diameter.

Effect of pulsed current on temperature distribution,weld bead profiles and characteristics of gas tungsten arc welded aluminum alloy joints

Temperature distribution and weld bead profiles of constant current and pulsed current gas tungsten arc welded aluminium alloy joints were compared. The effects of pulsed current welding on tensile properties, hardness profiles, microstructural features and residual stress distribution of aluminium alloy joints were reported. The use of pulsed current technique is found to improve the tensile properties of the weld compared with continuous current welding due to grain refinement occurring in the fusion zone.

Distribution Characteristics of High Temperature Damage and Its Influence on the Rice Yield in the Area along Huaihe River

[Objective] The research aimed to study the distribution characteristics of high temperature damage and its influence on the rice yield in the area along Huaihe River.[Method] The meteorological data of 10 stations in the area along Huaihe River during 1965-2009 and the yield data of Anhui single-season middle rice during 1967-2006 were selected.The occurrence characteristic of summer high temperature weather and the intensity of high temperature damage in the area along Huaihe River were analyzed.Based on the previous high temperature damage index of rice,Changfeng County where was the typical rice planting zone in the area along Huaihe River was as the representation,and the yield damage loss rate risk of high temperature damage in Changfeng was analyzed by combining with the historical yield data.[Result] The high temperature weather in the area along Huaihe River frequently happened.The high temperature damage presented 'N' shape trend from west to east.The occurrence frequency of high temperature weather in Huainan and Bengbu where were in the middle area along Huaihe River was more and was less in Huoqiu and Shouxian where were near the south mountain area of Anhui.The occurrence time mainly focused from the middle and last dekads of July to the first dekad of August after the plum rain.At this time,it was the booting,heading and flowering periods of single-season middle rice,and the influence on the rice yield was obvious.The damage loss rate of single-season middle rice yield in Changfeng County along Huaihe River continued to increase as the increasing of high temperature damage duration.But the occurrence probability decreased.The intensity grade of high temperature damage disaster loss rate which happened frequently concentrated mainly in levels I and II.The longer the high temperature damage duration in the reproductive growth stage of rice was,the bigger the damage loss rate was.But the corresponding occurrence probability was small,and vice versa.[Conclusion] The research provided the reference for assessing the high temperature disaster risk.

Carbon distribution strategy of Aurelia coerulea polyps in the strobilation process in relation to temperature and food supply

Mass occurrences of moon jellyfish have been observed in coastal waters. Strobilation directly determines the initial population size of adult jellyfish, but energy distribution during the strobilation process is not well understood. In this study, strobilation was induced in polyp of Aurelia coerulea by elevating temperature. The different stages in the strobilation process, including polyp budding, strobilation and body growth, were investigated at six temperature levels(8, 10, 13, 15, 17 and 19°C) and five food supply levels(0, 30, 60, 100 and 150 μg C/L). The results showed that the duration of strobilation preparation stage(SP) remarkably decreased with increasing temperature. Food level positively af fected the production of buds and ephyrae and the body growth of parent polyps. Of the six temperatures tested, 13°C was optimal for strobilation. At 13°C, strobilation activity was enhanced, and this treatment resulted in the greatest energy distribution, highest ephyrae production and longest duration of strobilation stage(SS). Polyps tended to allocate 6.58%–20.49% carbon to buds with sufficient food supply regardless of temperature. The body growth of parent polyps was highest at lower temperatures and higher food levels. This study is the first to provide information on carbon-based energy distribution strategy in the polyp strobilation process. We concluded that budding reproduction is a lower-risk strategy for A. coerulea polyps to increase populations. Even during strobilation season, polyps prioritize budding, but at the optimal strobilation temperature, polyps utilize a portion of the energy stored for budding to release ephyrae. The body carbon content of parent polyps may be considered as strategic energy reserves, which could help to support budding activities and strobilation during harsh conditions.

Distributional features of temperature and salinity in the southern Taiwan Strait and its adjacent sea areas in late summer, 1994

Based on the CTD data obtained in the southern Taiwan Strait and its adjacent areas in August and September of 1994, the distributional features of the temperature and salinity in the studied area have been analyzed in detail. The results are as follows: (1) There are two low temperature and high salinity regions in the nearshore area between Dongshan and Shantou and in the southeastern Taiwan Shoal, respectively, which may be caused by upwellings. (2) There exists a cold eddy in the northwestern sea area and a warm eddy with two high temperature cores in the eastern sea area of the Dongsha Islands, which are related to the anti-cyclonic turning of the seawater near the Dongsha Islands. (3) A westward high temperature and high salinity water tongue extends through the northern Luzon Strait and reaches the sea areas near the Dengsha Islands and southern Taiwan Strait.