Plasma Limiter Based on Surface Wave Plasma Excited by Microwave

A novel plasma limiter, in which the plasma is excited by surface wave, is presented. The breakdown time of some gases filled in the limiter were calculated as a function of gas pres- sure, ionization degree and density of seed electrons under low pressure （0.01 -1 Torr） and high pressure （10 -1000 Torr） cases. The results show that the limiter filled with Xe with a pressure of 0.9 Torr, seed electron density of 10^16 m^-3, and ionization degree of 10^-4, has a breakdown time of approximate 19.6 ns.

A statistical reappraisal of the relationship between liquid limit and specific surface area, cation exchange capacity and activity of clays

More than 500 datasets from the literature have been used to evaluate the relationships of specific surface area (SSA),cation exchange capacity (CEC) and activity versus the liquid limit (LL).The correlations gave R^2 values ranging between 0.71 and 0.92.Independent data were also used to validate the correlations.Estimated SSA values slightly overestimate the measured SSA up to 100 m^2/g.Regarding the estimated CEC values,they overestimated the measured CEC values up to 20 meq/(100 g).A probabilistic approach was performed for the correlations of SSA,CEC and activity versus LL.The analysis shows that the relations of SSA,CEC and activity with LL are robust.Using the LL values,it is possible to assess other basic engineering properties of clays.

Liquid-plastic Limit of Surface Sediments in North Slope of South China Sea

1 Introduction China has a vast area of continental shelf and is very rich in marine resources,but because of the complex geological environment and frequent geological disasters,the utilization of marine resources and the construction of marine engineering are limited(Zhu et al.,2016).As the

SURFACE YIELD STRENGTH AND FATIGUE LIMIT FOR STEELS

The surface yield strength(σ_(ms))for various carbon steels was studied by means of X-ray diffraction method.The results showed that it is.far below the bulk yield strength,and is the resistance against plastic deformation in the surface layer.The smooth fatigue limit is associ- ated with crack initiation which is a result of accumulation of plastic deformation.Experimen- tal results showed the relation of smooth fatigue limit for 50% survival with σ_(ms)is σ_(ms)=0.81 tO 1.02 σ_(-1)for different steels.The smooth fatigue limit of a medium carbon steel for 99.9% survival with σ_(ms)is σ_(ms)=0.98 tO 1.10 σ_(-1).It is less expensive and time consuming to measure σ_(ms)than σ_(-1).

A Method Combining Numerical Analysis and Limit Equilibrium Theory to Determine Potential Slip Surfaces in Soil Slopes

This paper describes a precise method combining numerical analysis and limit equilibrium theory to determine potential slip surfaces in soil slopes. In this method, the direction of the critical slip surface at any point in a slope is determined using the Coulomb’s strength principle and the extremum principle based on the ratio of the shear strength to the shear stress at that point. The ratio, which is considered as an analysis index, can be computed once the stress field of the soil slope is obtained. The critical slip direction at any point in the slope must be the tangential direction of a potential slip surface passing through the point. Therefore, starting from a point on the top of the slope surface or on the horizontal segment outside the slope toe, the increment with a small distance into the slope is used to choose another point and the corresponding slip direction at the point is computed. Connecting all the points used in the computation forms a potential slip surface exiting at the starting point. Then the factor of safety for any potential slip surface can be computed using limit equilibrium method like Spencer method. After factors of safety for all the potential slip surfaces are obtained, the minimum one is the factor of safety for the slope and the corresponding potential slip surface is the critical slip surface of the slope. The proposed method does not need to pre-assume the shape of potential slip surfaces. Thus it is suitable for any shape of slip surfaces. Moreover the method is very simple to be applied. Examples are presented in this paper to illustrate the feasibility of the proposed method programmed in ANSYS software by macro commands.

Simulation Study of Heat Flux Deposition Pattern on the Surface of HT-7 Toroidal Limiters

The heat flux deposition pattern on the toroidal limiters installed in HT-7 was simulated with ANSYS code. The simulation model was established with the ripple of the magnetic field. The heat deposition pattern and temperature distribution on the surface of the toroidal linfiters were obtained. A comparison of the results obtained with and without the shaped tiles, used to reduce the heat flux on the leading edge of the limiters, was made. The maximum heat load allowed at the leading edge was about 1.8 MW/m2 because of the poor power removing capacity on the ends of the limiters. This approach can also be applied to other devices with a limiter configuration in a circular cross-section shape.

Tubular limiting stream surface: “tornado” in three-dimensional vortical flow

A new physical structure of vortical flow, i.e., tubular limiting stream surface(TLSS), is reported. It is defined as a general mathematical structure for the physical flow field in the neighborhood of a singularity, and has a close relationship with limit cycles.The TLSS is a tornado-like structure, which separates a vortex into two regions, i.e., the inner region near the vortex axis and the outer region further away from the vortex axis.The flow particles in these two regions can approach to(or leave) the TLSS, but never could reach it.

Using a Surface Plasmon Resonance Biosensor for Rapid Detection of Salmonella Typhimurium in Chicken Carcass

Chicken is one of the most popular meat products in the world. Salmonella Typhimurium is a common foodbome pathogens associated with the processing of poultry. An optical Surface Plasmon Resonance （SPR） biosensor was sensitive to the presence of Salmonella Typhimurium in chicken carcass. The Spreeta biosensor kits were used to detect Salmonella Typhimurium on chicken carcass successfully. A taste sensor like electronic tongue or biosensors was used to basically ＂taste＂ the object and differentiated one object from the other with different taste sensor signatures. The surface plasmon resonance biosensor has potential for use in rapid, real-time detection and identification of bacteria, and to study the interaction of organisms with dif- ferent antisera or other molecular species. The selectivity of the SPR biosensor was assayed using a series of antibody con- centrations and dilution series of the organism. The SPR biosensor showed promising to detect the existence of Salmonella Typhimurium at 1 x 106 CFU/ml. Initial results show that the SPR biosensor has the potential for its application in pathogenic bacteria monitoring. However, more tests need to be done to confirm the detection limitation.

Advanced response surface method for mechanical reliability analysis

Based on the classical response surface method （RSM）, a novel RSM using improved experimental points （EPs） is presented for reliability analysis. Two novel points are included in the presented method. One is the use of linear interpolation, from which the total EPs for determining the RS are selected to be closer to the actual failure surface; the other is the application of sequential linear interpolation to control the distance be- tween the surrounding EPs and the center EP, by which the presented method can ensure that the RS fits the actual failure surface in the region of maximum likelihood as the center EPs converge to the actual most probable point （MPP）. Since the fitting precision of the RS to the actual failure surface in the vicinity of the MPP, which has significant contribution to the probability of the failure surface being exceeded, is increased by the presented method, the precision of the failure probability calculated by RS is increased as well. Numerical examples illustrate the accuracy and efficiency of the presented method.

Nonlinear aeroelastic analysis of a two-dimensional wing with control surface in supersonic flow

Based on the piston theory of supersonic flow and the energy method, a two dimensional wing with a control surface in supersonic flow is theoretically modeled, in which the cubic stiffness in the torsional direction of the control surface is considered. An approximate method of the cha- otic response analysis of the nonlinear aeroelastic system is studied, the main idea of which is that under the condi- tion of stable limit cycle flutter of the aeroelastic system, the vibrations in the plunging and pitching of the wing can approximately be considered to be simple harmonic excita- tion to the control surface. The motion of the control surface can approximately be modeled by a nonlinear oscillation of one-degree-of-freedom. The range of the chaotic response of the aeroelastic system is approximately determined by means of the chaotic response of the nonlinear oscillator. The rich dynamic behaviors of the control surface are represented as bifurcation diagrams, phase-plane portraits and PS diagrams. The theoretical analysis is verified by the numerical results.

Optimization principle of combined surface and underground mining and its applications

The pit limit optimization is discussed, which is one of the most important problems in the combined min-ing method, on the basis of the economic model of ore-blocks. A new principle of the limit optimization is put for-ward through analyzing the limitations of moving cone method under such conditions. With a view to recovering asmuch mineral resource as possible and making the maximum profit from the whole deposit, the new principle is tomaximize the sum of gain from both open-pit and underground mining. The mathematical models along the horizon-tal and vertical directions and modules for software package (DM&MCAD) have been developed and tested inTonglushan Copper Mine. It has been proved to be rather effective in the mining practice.

Enhancement of the flux for polypropylene hollow fiber membrane in a submerged membrane-bioreactor by surface modification

To improve its limiting flux and antifouling characteristics in a submerged membrane-bioreactor （SMBR） for wastewater treatment, polypropylene hollow fiber microporous membrane （PPHFMM） was surface-modified by the plasma-induced immobilization of poly （N-vinyl-2-pyrrolidone） （PVP） and the plasma treatment with different gases respectively. Attenuated total reflection-Fourier transform infrared spectroscopy （FT-IR/ATR）, X-ray photoelectron spectroscopy （XPS） and field emission scanning electron microscope （FE-SEM） were used to characterize the structural and morphological changes on the membrane surface. Water contact angle was measured by the sessile drop method. It was found that the water contact angle was 128.8, 72.3, 62.7, 74.4, 79.1, 86.3, and 71.3° for the nascent, PVP-immobilized, air, 02, Ar, CO2 and H2O plasma treated PPHFMM, respectively. The SMBR was operated at fixed transmembrane pressure to determine the limiting flux for the PPHFMM before and after surface modification. Results showed that the limiting flux appeared to be 103, 159, 117, 133, 136, 121 and 152 L/（m^2· h） for the nascent, PVP-immobilized, air, O2, At, CO2 and H2O plasma treated PPHFMM, respectively. After continuous operation for about 50 h in the SMBR, the antifouling characteristics were improved to some extent.

Failure mechanism of large-diameter shield tunnels and its effects on ground surface settlements

A new technique for the analysis of the three-dimensional collapse failure mechanism and the ground surface settlements for the large-diameter shield tunnels were presented.The technique is based on a velocity field model using more different truncated solid conical blocks to clarify the multiblock failure mechanism.Furthermore,the shape of blocks between the failure surface and the tunnel face was considered as an entire circle,and the supporting pressure was assumed as non-uniform distribution on the tunnel face and increased with the tunnel embedded depth.The ground surface settlements and failure mechanism above large-diameter shield tunnels were also investigated under different supporting pressures by the finite difference method.

INFLUENCE OF RESIDUAL STRESS AND SURFACE MORPHOLOGY ON FATIGUE PROPERTIES OF STEEL 60Mn

Influence of residual stress and surface morphology induced by shot-peening on fatigue behav- ior of a medium temperature tempered spring steel 60 Mn has been studied.The compressive residual stress induced in the near-surface region may improve fatigue limit from 930 to 1010 MPa,and the very high tensile residual stress in the interior may reduce it from 1010 to 940 MPa,whereas the severe surface damage may cause a drop-off of it from 1010 down to 800 MPa.Fatigue cracks initiated in such position where the equivalent Mises stress,including residual stress,exceeded the local strength of the material.The compressive residual stress, induced by shot-peening,may intensify the effect of crack closure,so as to decrease the crack growth rate.

Seismic stability analysis of slopes with pre-existing slip surfaces

In analyzing seismic stability of a slope with upper bound limit analysis method, the slip surface is often assumed as a log-spiral or plane slip surface. However, due to the presence of a weak layer and unfavorable geological structural surface or a bedrock interface with overlying soft strata, the preexisting slip surface of the slope may be irregular and composed of a series of planes rather than strictly logspiral or plane shape. A computational model is developed for analyzing the seismic stability of slopes with pre-existing slip surfaces. This model is based on the upper bound limit analysis method and can consider the effect of anchor bolts. The soil or rock is deemed to follow the Mohr-Coulomb yield criterion. The slope is divided into multiple block elements along the slip surface. According to the displacement compatibility and the associated flow rule, a kinematic velocity field of the slope can be obtained computationally. The proposed model allows not only calculation of the rate of external work owing to the combined effect of self-weight and seismic loading, but also that of the energy dissipation rate caused by the slip surface, interfaces of block elements and anchorage effect of the anchors. Considering a direct relationship between the rate of external work and the energy dissipation rate, the expressions of yield acceleration and permanent displacement of anchored slopes can be derived. Finally, the validity of this proposed model is illustrated by analysis on three typical slopes. The results showed that the proposed model is more easily formulated and does not need to solve complex equations or time consuming iterations compared with previous methods based on the conditions of force equilibrium.

Improvements on Mean Free Wave Surface Modeling

Some new results of the modeling of mean free surface of waves or wave set-up are presented. The stream function wave theory is applied to incident short waves. The limiting wave steepness is adopted as the wave breaker index in the calculation of wave breaking dissipation. The model is based on Roelvink (1993), but the numerical techniques used in the solution are based on the Weighted-Average Flux (WAF) method (Watson et al., 1992), with Time-Operator-Splitting (TOS) used for the treatment of the source terms. This method allows a small number of computational points to be used, and is particularly efficient in modeling wave set-up. The short wave (or incident primary wave) energy equation is solved by use of a traditional Lax-Wendroff technique. The present model is found to be satisfactory compared with the measurements conducted by Stive (1983).

Fractal characteristics investigation on electromagnetic scattering from 2-D Weierstrass fractal dielectric rough surface

A normalized two-dimensional band-limited Weierstrass fractal function is used for modelling the dielectric rough surface. An analytic solution of the scattered field is derived based on the Kirchhoff approximation. The variance of scattering intensity is presented to study the fractal characteristics through theoretical analysis and numerical calculations. The important conclusion is obtained that the diffracted envelope slopes of scattering pattern can be approximated as a slope of linear equation. This conclusion will be applicable for solving the inverse problem of reconstructing rough surface and remote sensing.

Superficial Layer MHD Effect and Full-Cover Free Surface Flow Characterizing

Up to now, no a real full-cover liquid metal (LM) free surface flow have been successfully used in magnetic fusion devices as MHD instability and unavoidable rivulet flow. Recently, after we carried out a guidable free curve-surface flow on theoretically and experimentally, seeking for other way to get a full-cover free surface flow is also in implementing. The superficial layer MHD effect in free surface flow is experimentally observed. After compared and analyzed the characteristic parameters of the free surface flow, the conditions of full-cover free surface flow are found. Meanwhile, the new two parameters of surface cover ratio and rivulet flow index are introduced to characterize the flowing characteristic of the full-cover free surface flow under magnetic field. According to the analysis rule, for different liquid metal, there are the different unique conditions to meet full-cover free surface flow under magnetic field. This may be a way to solve free surface flow major MHD key issue for LM PFCs.

广义对数螺旋型滑面模型的构建与验证

临界滑动面的合理确定是边坡稳定性分析的关键问题之一。传统的边坡滑动面假设方法构造生成的潜在滑动面形式单一,且无法考虑复杂边坡中土层强度参数变化对临界滑动面形状的影响,从而降低了边坡稳定性分析结果的可靠性。基于此,提出一种新的广义对数螺旋型滑面模型,该模型可生成包含传统圆弧滑动面和对数螺旋滑动面在内的多种形式的潜在滑动面;并针对非均质边坡中各土层抗剪强度不同的特点,采用多中心分段构造策略,将该滑面模型应用于非均质边坡稳定性分析中。基于极限平衡理论计算滑动面安全系数并搜索临界滑动面,对边坡进行稳定性评估。选取多个均质边坡及多种型式的非均质边坡(水平分层、倾斜分层和斜折线分层)经典算例与现有研究成果以及数值模拟软件获得的结果进行对比分析,验证该滑面模型的合理性与优势性。研究结果表明:文中方法计算所得安全系数与其他方法相比更小,相对误差在5%以内。能够得到传统滑动面假设方法下难以搜索到的临界滑动面,并与数值模拟结果吻合度较好,稳定性分析结果更接近实际情况。由此说明,此方法用于均质边坡及非均质边坡稳定性分析是合理可行的,有望为工程实践提供更优的临界滑动面解决方案。

原子精度制造新原理和新方法

目前航空航天、核物理、微电子、光电子和半导体等国家战略领域高性能装备的性能需求日渐严苛,核心零部件的制造精度必须迈进原子级水平,亟需研究原子精度的高性能制造新原理和新方法。本文归纳并提出了目前迫切需求的原子级表面精度、原子级结构精度、原子级损伤控制以及原子级特征尺寸结构创成四大原子精度制造核心能力,从能场辅助原子级切削、多能场辅助原子有序排布、表面能弱化原子精度材料去除以及超光学衍射极限的原子精度制造四大方向进行系统梳理,介绍了面向不同应用场景的原子精度制造新原理和新方法的研究现状,并概述了各类方法的优势和缺点,从中提炼出多能场耦合条件下的能量和原子间相互作用机理这一关键科学问题,并从四大方向上对未来我国原子级制造的基础研究提出了建议。