Timer error as well as its convention is very important for dose accuracy during irradiation. This paper determines the timer error of irradiators at Secondary Standard Dosimetry Laboratory (SSDL) in Nigeria. The irra...Timer error as well as its convention is very important for dose accuracy during irradiation. This paper determines the timer error of irradiators at Secondary Standard Dosimetry Laboratory (SSDL) in Nigeria. The irradiators are Cs-137 OB6 irradiator and X-ray irradiators at the Protection level SSDL;and Co-60 irradiator at the Therapy Level SSDL. PTW UNIDOS electrometer and LS01 Ionization chamber were used at the Protection Level to obtain doses for both Cs-137 OB6 and X-ray irradiators while an IBA farmer type ionization chamber and an IBA DOSE 1 electrometer were used at the Protection Level SSDL. Single/multiple exposure method and graphical method were used in the determination of the timer error for the three irradiators. The timer error obtained for Cs-137 OB6 irradiator was 0.48 ± 0.01 s, the timer error for the X-ray irradiator was 0.09 ± 0.01 s while the timer error obtained for GammaBeam X200 was 1.21 ± 0.04 s. It was observed that the timer error is not affected by source to detector distance. It was also observed that the timer error of Co-60 Gamma X200 irradiator is increasing with the age of the machine. Source to detector distance and field size do not contribute towards the timer error of the irradiators. The timer error of the Co-60 Gamma X200 irradiator (the only irradiator among the irradiators with a pneumatic system) increases with the age of the irradiator.展开更多
Developing a novel drop counter by introducing the Internet of Things concept has been vigorously conducted in recent years. Understanding the newly introduced drop counter’s flow rate control accuracy and flow rate ...Developing a novel drop counter by introducing the Internet of Things concept has been vigorously conducted in recent years. Understanding the newly introduced drop counter’s flow rate control accuracy and flow rate count feature is essential for improving safety in infusion management. This study aimed to verify if the new drop counters could secure accurate flow rate and drip count by conducting actual flow rate measurements using gravimetry and functional evaluation. A drop counter was attached to each drip chamber of the infusion set, and an IV drip was conducted at the 100 ml/h flow rate. The weight of discharged physiological saline was measured to plot trumpet curves. Next, three different types of drop counters were evaluated to determine if they maintained drip count accuracy according to the changes in their position angles. The flow rate errors in all conditions indicated trumpet-like curves, exhibiting an overall error range within ±10% in all observation windows. Although every drop counter successfully detected and measured dripping, it was challenging in some counters to detect dripping when the drip chamber was tilted. In comparing adult and pediatric IV sets, the adult IV set was found to be less likely to detect dripping in the angled position. No significant differences in results were confirmed between high and low flow rates, suggesting that the drop count function would not be affected by the flow rate in the ranges of typical infusion practices. Doppler sensors have a wide range of measurements and high sensitivity;the dripping was detected successfully even when the drip chamber was tilted, probably due to the advantages of these sensors. In contrast, miscounts occurred in those equipped with infrared sensors, which could not detect light intensity changes in tilted positions. Understanding the tendencies in flow rate errors in infusion can be valuable information for infusion management.展开更多
In the metrology of radon, an environmental lung carcinogen, the integrated measurements necessary for epidemiological studies are made very often using the tracks detector LR 115 type 2. For dosimetric analysis, the ...In the metrology of radon, an environmental lung carcinogen, the integrated measurements necessary for epidemiological studies are made very often using the tracks detector LR 115 type 2. For dosimetric analysis, the etched tracks from radon alpha particles on this detector are usually counted by means of an optical microscope or a spark counter. An optimal reading of the track densities which must be converted into radon concentrations, can’t be done without a good mastery of the mode of operation and use of these devices. Furthermore, investigations to know as to whether or not each of those can be used to determine radon concentration are necessary. These are the objectives of the present work in which LR 115 samples exposed to radon for at least 3 months, were chemically developed under standard conditions and read. The track densities obtained with the microscope are very much higher than those of the counter for each sample. These results are consistent with those published by other authors. However, each of these devices can be used interchangeably for alpha tracks counting, as both provide radon concentrations with a very good linear correlation coefficient of 0.95 taking into account their respective calibration factors for the reading of this detector. In addition, the saturation phenomenon for the spark counter reading of LR 115 detector occurs beyond 11,000 tr/cm<sup>2</sup>, a density never reached during our environmental radon measurements.展开更多
In this paper,the throughput and delay of cooperative communications are derived when solar energy is used and relay node is selected using a timer.The source and relays harvest energy from sun using a photo voltaic s...In this paper,the throughput and delay of cooperative communications are derived when solar energy is used and relay node is selected using a timer.The source and relays harvest energy from sun using a photo voltaic system.The harvested power is used by the source to transmit data to the relays.Then,a selected relay amplifies the signal to the destination.Opportunistic,partial and reactive relay selection are used.The relay transmits when its timer elapses.The timer is set to a value proportional to the inverse of its Signal to Noise Ratio(SNR).Therefore,the relay with largest SNR will transmit first and its signal will be detected by the other relays that will remain idle to avoid collisions.Harvesting duration is optimized to maximize the throughput.Packet’s waiting time and total delay are also computed.We also derive the statistics of SNR when solar energy is used.The harvested power from sun is proportional to the sum of a deterministic radiation intensity and a random attenuation due to weather effects and clouds occlusion.The fixed radiation intensity depends on season,month and time t in hour.The throughput of cooperative communications with energy harvesting from sun was not yet studied.展开更多
Taking a propfan engine as the research object,the CFD method was used for 3D modeling and unsteady slip flow for numerical calculation.The propfan rotation domain and the nacelle outside flow domain were meshed by us...Taking a propfan engine as the research object,the CFD method was used for 3D modeling and unsteady slip flow for numerical calculation.The propfan rotation domain and the nacelle outside flow domain were meshed by using the partition splicing grid technology.Used the Reynolds⁃averaged of N⁃S equation,the Reynolds stress term uses the RNG turbulence model;and based on the slip grid method,numerical calculation of the flow field with different Mach numbers,front and rear blade angles and engine state were carried out;and the change law of propeller fan characteristics and the influence of slip flow on the inlet flow field were analyzed.The blade angle was the key parameter of the propeller fan characteristic conditions.When the blade angle increases from 41°to 50°,the thrust coefficient increases by 31.2%,and the power coefficient increases by 33.4%;in the climbing state of the propeller fan,the maximum total pressure distortion at the inlet port of 6.8%;the cross section is less affected by the slip flow of the propfan;and the pressure distribution is relatively uniform,but the area of the flow channel is small.The research results can provide a solution for the matching of the counter⁃rotating propeller fan and the engine and the arrangement of the air inlet measuring rake.展开更多
文摘Timer error as well as its convention is very important for dose accuracy during irradiation. This paper determines the timer error of irradiators at Secondary Standard Dosimetry Laboratory (SSDL) in Nigeria. The irradiators are Cs-137 OB6 irradiator and X-ray irradiators at the Protection level SSDL;and Co-60 irradiator at the Therapy Level SSDL. PTW UNIDOS electrometer and LS01 Ionization chamber were used at the Protection Level to obtain doses for both Cs-137 OB6 and X-ray irradiators while an IBA farmer type ionization chamber and an IBA DOSE 1 electrometer were used at the Protection Level SSDL. Single/multiple exposure method and graphical method were used in the determination of the timer error for the three irradiators. The timer error obtained for Cs-137 OB6 irradiator was 0.48 ± 0.01 s, the timer error for the X-ray irradiator was 0.09 ± 0.01 s while the timer error obtained for GammaBeam X200 was 1.21 ± 0.04 s. It was observed that the timer error is not affected by source to detector distance. It was also observed that the timer error of Co-60 Gamma X200 irradiator is increasing with the age of the machine. Source to detector distance and field size do not contribute towards the timer error of the irradiators. The timer error of the Co-60 Gamma X200 irradiator (the only irradiator among the irradiators with a pneumatic system) increases with the age of the irradiator.
文摘Developing a novel drop counter by introducing the Internet of Things concept has been vigorously conducted in recent years. Understanding the newly introduced drop counter’s flow rate control accuracy and flow rate count feature is essential for improving safety in infusion management. This study aimed to verify if the new drop counters could secure accurate flow rate and drip count by conducting actual flow rate measurements using gravimetry and functional evaluation. A drop counter was attached to each drip chamber of the infusion set, and an IV drip was conducted at the 100 ml/h flow rate. The weight of discharged physiological saline was measured to plot trumpet curves. Next, three different types of drop counters were evaluated to determine if they maintained drip count accuracy according to the changes in their position angles. The flow rate errors in all conditions indicated trumpet-like curves, exhibiting an overall error range within ±10% in all observation windows. Although every drop counter successfully detected and measured dripping, it was challenging in some counters to detect dripping when the drip chamber was tilted. In comparing adult and pediatric IV sets, the adult IV set was found to be less likely to detect dripping in the angled position. No significant differences in results were confirmed between high and low flow rates, suggesting that the drop count function would not be affected by the flow rate in the ranges of typical infusion practices. Doppler sensors have a wide range of measurements and high sensitivity;the dripping was detected successfully even when the drip chamber was tilted, probably due to the advantages of these sensors. In contrast, miscounts occurred in those equipped with infrared sensors, which could not detect light intensity changes in tilted positions. Understanding the tendencies in flow rate errors in infusion can be valuable information for infusion management.
文摘In the metrology of radon, an environmental lung carcinogen, the integrated measurements necessary for epidemiological studies are made very often using the tracks detector LR 115 type 2. For dosimetric analysis, the etched tracks from radon alpha particles on this detector are usually counted by means of an optical microscope or a spark counter. An optimal reading of the track densities which must be converted into radon concentrations, can’t be done without a good mastery of the mode of operation and use of these devices. Furthermore, investigations to know as to whether or not each of those can be used to determine radon concentration are necessary. These are the objectives of the present work in which LR 115 samples exposed to radon for at least 3 months, were chemically developed under standard conditions and read. The track densities obtained with the microscope are very much higher than those of the counter for each sample. These results are consistent with those published by other authors. However, each of these devices can be used interchangeably for alpha tracks counting, as both provide radon concentrations with a very good linear correlation coefficient of 0.95 taking into account their respective calibration factors for the reading of this detector. In addition, the saturation phenomenon for the spark counter reading of LR 115 detector occurs beyond 11,000 tr/cm<sup>2</sup>, a density never reached during our environmental radon measurements.
基金the Deanship of Scientific Research at Saudi Electronic University for funding this research work through the project number 8092.
文摘In this paper,the throughput and delay of cooperative communications are derived when solar energy is used and relay node is selected using a timer.The source and relays harvest energy from sun using a photo voltaic system.The harvested power is used by the source to transmit data to the relays.Then,a selected relay amplifies the signal to the destination.Opportunistic,partial and reactive relay selection are used.The relay transmits when its timer elapses.The timer is set to a value proportional to the inverse of its Signal to Noise Ratio(SNR).Therefore,the relay with largest SNR will transmit first and its signal will be detected by the other relays that will remain idle to avoid collisions.Harvesting duration is optimized to maximize the throughput.Packet’s waiting time and total delay are also computed.We also derive the statistics of SNR when solar energy is used.The harvested power from sun is proportional to the sum of a deterministic radiation intensity and a random attenuation due to weather effects and clouds occlusion.The fixed radiation intensity depends on season,month and time t in hour.The throughput of cooperative communications with energy harvesting from sun was not yet studied.
文摘Taking a propfan engine as the research object,the CFD method was used for 3D modeling and unsteady slip flow for numerical calculation.The propfan rotation domain and the nacelle outside flow domain were meshed by using the partition splicing grid technology.Used the Reynolds⁃averaged of N⁃S equation,the Reynolds stress term uses the RNG turbulence model;and based on the slip grid method,numerical calculation of the flow field with different Mach numbers,front and rear blade angles and engine state were carried out;and the change law of propeller fan characteristics and the influence of slip flow on the inlet flow field were analyzed.The blade angle was the key parameter of the propeller fan characteristic conditions.When the blade angle increases from 41°to 50°,the thrust coefficient increases by 31.2%,and the power coefficient increases by 33.4%;in the climbing state of the propeller fan,the maximum total pressure distortion at the inlet port of 6.8%;the cross section is less affected by the slip flow of the propfan;and the pressure distribution is relatively uniform,but the area of the flow channel is small.The research results can provide a solution for the matching of the counter⁃rotating propeller fan and the engine and the arrangement of the air inlet measuring rake.
