Photocatalytic activity of metal nanoparticle-decorated titanium dioxide for simultaneous H_(2) production and biodiesel wastewater remediation

A set of metal nanoparticle-decorated titanium dioxide(Mx/TiO_(2);where x is the percent by mass,%)photocatalysts was prepared via the sol-immobilization in order to enhance the simultaneous hydrogen(H_(2))production and pollutant reduction from real biodiesel wastewater.Effect of the metal nanoparticle(NP)type(M=Ni,Au,Pt or Pd)and,for Pd,the amount(1%–4%)decorated on the surface of thermal treated commercial TiO_(2)(T_(400))was evaluated.The obtained results demonstrated that both the type and amount of decorated metal NPs did not significantly affect the pollutant reduction,measured in terms of the reduction of chemical oxygen demand(COD),biological oxygen demand(BOD)and oil&grease levels,but they affected the H_(2) production rate from both deionized water and biodiesel wastewater,which can be ranked in the order of Pt_(1)/T_(400)>Pd_(1)/T_(400)>Au_(1)/T_(400)>Ni_(1)/T_(400).This was attributed to the high difference in work function between Pt and the parent T400.However,the difference between Pt1/T400 and Pd1/T400 was not great and so from an economic consideration,Pd/TiO_(2) was selected as appropriate for further evaluation.Among the four different Pdx/TiO_(2) photocatalysts,the Pd3/TiO_(2) demonstrated the highest activity and gave a high rate of H_(2) production(up to 135 mmol·h−1)with a COD,BOD and oil&grease reduction of 30.3%,73.7%and 58.0%,respectively.

Preparation of Cd S Microcrystallite Doped Si O_2 Glass Films on Titaniu m-m etal Substrates by Sol- Gel Process

CdS microcrystallite doped SiO 2 glass films on titanium metal substrates were prepared by sol gel process. The effects of solution composition and viscosity, heat treatment parameters and substrate pretreatment method on the film qualities were studied. The transformation process of gel to CdS doped SiO 2 glass film, the structure of these films, the substrate/film interface bonding state and crystalline phase were analyzed by DTA, IRRS, SEM, EDS and XRD. The IRRS results show that Si O Ti linkages are formed between titanium substrate and thin film during heat treatment process. The preferential heat treatment of titanium surface in oxidizing atmosphere will be beneficial to increase the interface bonding strength. The thin films bonded with the substrates chemically and contained very fine CdS crystals with 20～40 nm in size.

Potential Application of Entangled Porous Titanium Alloy Metal Rubber in Artificial Lumbar Disc Prostheses

Entangled Porous Titanium Alloy Metal Rubber(EPTA-MR)was used as a nucleus pulposus material in the design of non-fusion intervertebral disc prosthesis for the first time.A novel artificial lumbar intervertebral disc prosthesis was designed by reconstructing the lumbar model with reverse engineering technology,and the biomechanical behavior of the prosthesis was simulated under varied working conditions.The nucleus pulposus size was determined by the actual size of human prosthesis.EPTA-MR samples with different densities were prepared by medical titanium alloy wire experimental studies were conducted on static stiffness,damping energy consumption,and fatigue life.The results indicated that the static stiffness of EPTA-MR could reach approximately 1500 N mm and its loss factor remained higher than 0.2,and the variation range was relatively small,with excellent vibration damping capacity and bearing capacity.Among them,the overall performance of EPTA-MR with a density of 2.5 g em 3 was closer to that of the physiologic intervertebral disc.A macro experiment of five million fatigue vibration tests combined with microstructure observation exhibited a wear rate of only 0.9396 g-MC with no noticeable change in the internal micro-morphology.Therefore,the EPTA-MR has a broad application prospect as the nucleus pulposus material of artificial intervertebral disc prosthesis.

Combined effects of adsorption and photocatalysis by hybrid TiO_2/ZnO-calcium alginate beads for the removal of copper

The use of nanosized titanium dioxide（TiO2） and zinc oxide（ZnO） in the suspension form during treatment makes the recovering and recycling of photocatalysts difficult.Hence,supported photocatalysts are preferred for practical water treatment applications.This study was conducted to investigate the efficiency of calcium alginate（CaAlg） beads that were immobilized with hybrid photocatalysts,TiO2/ZnO to form TiO2/ZnO-CaAlg.These immobilized beads,with three different mass ratios of TiO2：ZnO（1：1,1：2,and 2：1） were used to remove Cu（Ⅱ） in aqueous solutions in the presence of ultraviolet light.These beads were subjected to three cycles of photocatalytic treatment with different initial Cu（Ⅱ） concentrations（10-80 ppm）.EDX spectra have confirmed the inclusion of Ti and Zn on the surface of the CaAlg beads.Meanwhile,the surface morphology of the beads as determined using SEM,has indicated differences of before and after the photocatalytic treatment of Cu（Ⅱ）.Among all three,the equivalent mass ratio TiO2/ZnO-CaAlg beads have shown the best performance in removing Cu（Ⅱ） during all three recycling experiments.Those TiO2/ZnO-CaAlg beads have also shown consistent removal of Cu,ranging from 7.14-52.0 ppm（first cycle） for initial concentrations of10-80 ppm.In comparison,bare CaAlg was only able to remove 6.9-48 ppm of similar initial Cu concentrations.Thus,the potential use of TiO2/ZnO-CaAlg beads as environmentally friendly composite material can be further extended for heavy metal removal from contaminated water.

Influences of Technological Parameters on Smelting-separation Process for Metallized Pellets of Vanadium-bearing Titanomagnetite Concentrates

The smelting-separation process for metallized pellets of vanadium-bearing titanomagnetite concentrates was studied.The influences of smelting temperature,smelting time,and the basicity of the metallized pellet on vanadium and iron recovery were investigated.The characteristics of titanium slag were analyzed using X-ray diffraction,energy dispersive spectroscopy,and mineralographic microscopic analysis.The results demonstrate that appropriate increases in smelting temperature and smelting time can improve the vanadium and iron recovery from metallized pellets and are beneficial for the slag-iron separation.Although increasing the basicity of the metallized pellet can considerably improve the vanadium and iron recovery,the TiO;grade of titanium slag was decreased.Under the optimal conditions,90.17% of vanadium and 92.98% of iron in the metallized pellet were recovered,and the TiO;grade of titanium slag was 55.01%.It was found that anosovite,augite,spinel,glassiness,and metallic iron were the main mineral phases of the titanium slag.