To characterize the effects of alloying elements on inclusion dissolution of titanium nitride, the content profiles of elements around TiN/Ti boundary α phase regions in liquid titanium alloys have been experimentall...To characterize the effects of alloying elements on inclusion dissolution of titanium nitride, the content profiles of elements around TiN/Ti boundary α phase regions in liquid titanium alloys have been experimentally carried out. Four kinds of commercial alloys of CpTi, Ti64, Ti17 and Ti6242 containing different α stabilizing or β stabilizing elements are examined through artificially embedding the TiN sponge particle into liquid alloys in VAR conditions. The content profiles of nitrogen and alloying elements around TiN/Ti boundary were measured by WDX and microprobe for as cast samples. The content profiles of nitrogen and alloying elements around N containing solid in α Ti region of these alloys show a common features of a steep change. In particular, the content profiles of elements for Ti6242 demonstrate unique change of a more gentle change tendency and further deeper into the alloy matrix. The experiment results show that, the differences among composite effects of alloying elements in different alloys within nitrogen induced diffusion α region result in different dissolution and diffusion behaviors to overcome the α phase region barriers.展开更多
This paper reports a study of the addition effects of either titanium or titanium and nitrogen of steel grade DIN 56NiCrMoV7 on mechanical properties. Three steel grades were produced in 30 kg-induction furnace, one c...This paper reports a study of the addition effects of either titanium or titanium and nitrogen of steel grade DIN 56NiCrMoV7 on mechanical properties. Three steel grades were produced in 30 kg-induction furnace, one conforms the chemical composition of conventional 56NiCrMoV7 while the other two produced steels were microalloyed by either titanium or titanium and nitrogen. The produced cast steel grades were reheated to 1150°C and hold for 2 hours, followed by forging process. The forging process was carried out in temperature range 950°C - 1100°C. Solution treatment of hot forged steels was conducted at 880°C, 850°C followed by air and oil quenching, respectively. Quenched steel samples of different steel grades were tempered at different temperatures in the range of 300°C to 650°C for 45 min. The hardness variations after tempering of the two modified steels comparing with the conventional 56NiCrMoV7 steel were studied. Microadditions of titanium or titanium and nitrogen were found to produce secondary hardening at 550°C to 575°C (45 min) with a hardness peak higher than that attained in the conventional 56NiCrMoV7 steel. The effect of titanium and nitrogen additions on phases formation was investigated by Thermo-Calc. SEM was used to confirm Thermo-Calc analysis. Interpretation between hardness and formed phases has been illustrated.展开更多
Nitrogen-doped TiO2 nanocrystalline powders were prepared by hydrolysis of tetrachloride titanium （TiCl4） in a mixed solution of ethanol and ammonium nitrate （NH4NO3） at ambient temperature and atmosphere followed...Nitrogen-doped TiO2 nanocrystalline powders were prepared by hydrolysis of tetrachloride titanium （TiCl4） in a mixed solution of ethanol and ammonium nitrate （NH4NO3） at ambient temperature and atmosphere followed by calcination at 400 ℃ for 2 h in air. FTIR spectra demonstrate that amine group in original gel is eliminated by calcination, and the TiO2 powder is liable to absorb water onto its surface and into its capillary pore. XRD and SEM results show that the average size of nanocrystalline TiO2 particles is no more than 60 nm and with increasing the calcination temperature, the size of particles increases. XPS studies indicate the nitrogen atom enters into the TiO2 lattice and occupies the position of oxygen atom. The nitrogen doping not only depresses the grain growth of TiO2 particles, but also reduces the phase transformation temperature of anatase to futile. The photocatalytic activity of the nitrogen-doped TiO2 powders has been evaluated by experiments of photocatalytic degradation aqueous methylene blue.展开更多
Nitrogen ion was implanted into the nano-TiO2 film surfaces by electron cyclotron resonance （ECR） plasma modification to improve the optical reactivity in visible-light region for nano-TiO2. Diagnosing the N2 plasma...Nitrogen ion was implanted into the nano-TiO2 film surfaces by electron cyclotron resonance （ECR） plasma modification to improve the optical reactivity in visible-light region for nano-TiO2. Diagnosing the N2 plasma by optical emission spectroscopy （OES） was applied to the process of plasma modification. X-ray photoelectron spectroscopy （XPS） was used for analysis of the binding of element after plasma modification. It is shown that the surface modification was caused by excitated N. The injecting of N2 and N＋ leads to the increase in the dissociative interstitial state N in the films. The doped N makes for TiO2-xNx appearing in the TiO2 films. TiO2-xNx forms the impurity energy state in the TiO2 energy band gap and reduces the energy band gap. This is the main reason leading to the red shift of absorption edge.展开更多
Deducting interference method was applied to determine the concentration of nitrogen in the presence of Ti.This procedure is available in treating the interference of same order diffraction in EPMA.
The characteristics of nitrided layers prepared on commercially pure titanium substrates by direct current nitrogen arc are presented by scanning electron microscopy （SEM） and transmission electron microscopy （TEM...The characteristics of nitrided layers prepared on commercially pure titanium substrates by direct current nitrogen arc are presented by scanning electron microscopy （SEM） and transmission electron microscopy （TEM） micrographs as well as X-ray diffraction （ XRD ）. The titanium nitride （ TiN ） dendrites were fully developed with interconnected cellular morphologies at the top surface but grew almost perpendicular to the integrace with coarser arms in the middle area. Also less TiN was found near the interface. The energy inputs had an obvious effect on the microstructures and the hardness of the nitrided layers. The maximum micro-hardness was 2 500 HV at the top surface which was over 9 times higher than that of the substrate.展开更多
文摘To characterize the effects of alloying elements on inclusion dissolution of titanium nitride, the content profiles of elements around TiN/Ti boundary α phase regions in liquid titanium alloys have been experimentally carried out. Four kinds of commercial alloys of CpTi, Ti64, Ti17 and Ti6242 containing different α stabilizing or β stabilizing elements are examined through artificially embedding the TiN sponge particle into liquid alloys in VAR conditions. The content profiles of nitrogen and alloying elements around TiN/Ti boundary were measured by WDX and microprobe for as cast samples. The content profiles of nitrogen and alloying elements around N containing solid in α Ti region of these alloys show a common features of a steep change. In particular, the content profiles of elements for Ti6242 demonstrate unique change of a more gentle change tendency and further deeper into the alloy matrix. The experiment results show that, the differences among composite effects of alloying elements in different alloys within nitrogen induced diffusion α region result in different dissolution and diffusion behaviors to overcome the α phase region barriers.
文摘This paper reports a study of the addition effects of either titanium or titanium and nitrogen of steel grade DIN 56NiCrMoV7 on mechanical properties. Three steel grades were produced in 30 kg-induction furnace, one conforms the chemical composition of conventional 56NiCrMoV7 while the other two produced steels were microalloyed by either titanium or titanium and nitrogen. The produced cast steel grades were reheated to 1150°C and hold for 2 hours, followed by forging process. The forging process was carried out in temperature range 950°C - 1100°C. Solution treatment of hot forged steels was conducted at 880°C, 850°C followed by air and oil quenching, respectively. Quenched steel samples of different steel grades were tempered at different temperatures in the range of 300°C to 650°C for 45 min. The hardness variations after tempering of the two modified steels comparing with the conventional 56NiCrMoV7 steel were studied. Microadditions of titanium or titanium and nitrogen were found to produce secondary hardening at 550°C to 575°C (45 min) with a hardness peak higher than that attained in the conventional 56NiCrMoV7 steel. The effect of titanium and nitrogen additions on phases formation was investigated by Thermo-Calc. SEM was used to confirm Thermo-Calc analysis. Interpretation between hardness and formed phases has been illustrated.
基金National Natural Science Foundation of China (No. 20276056)Shaanxi Natural Science Foundation (No. 2003E225)
文摘Nitrogen-doped TiO2 nanocrystalline powders were prepared by hydrolysis of tetrachloride titanium （TiCl4） in a mixed solution of ethanol and ammonium nitrate （NH4NO3） at ambient temperature and atmosphere followed by calcination at 400 ℃ for 2 h in air. FTIR spectra demonstrate that amine group in original gel is eliminated by calcination, and the TiO2 powder is liable to absorb water onto its surface and into its capillary pore. XRD and SEM results show that the average size of nanocrystalline TiO2 particles is no more than 60 nm and with increasing the calcination temperature, the size of particles increases. XPS studies indicate the nitrogen atom enters into the TiO2 lattice and occupies the position of oxygen atom. The nitrogen doping not only depresses the grain growth of TiO2 particles, but also reduces the phase transformation temperature of anatase to futile. The photocatalytic activity of the nitrogen-doped TiO2 powders has been evaluated by experiments of photocatalytic degradation aqueous methylene blue.
基金the Guangdong Provincial Natural Science Foundation under grant No. 031502.
文摘Nitrogen ion was implanted into the nano-TiO2 film surfaces by electron cyclotron resonance （ECR） plasma modification to improve the optical reactivity in visible-light region for nano-TiO2. Diagnosing the N2 plasma by optical emission spectroscopy （OES） was applied to the process of plasma modification. X-ray photoelectron spectroscopy （XPS） was used for analysis of the binding of element after plasma modification. It is shown that the surface modification was caused by excitated N. The injecting of N2 and N＋ leads to the increase in the dissociative interstitial state N in the films. The doped N makes for TiO2-xNx appearing in the TiO2 films. TiO2-xNx forms the impurity energy state in the TiO2 energy band gap and reduces the energy band gap. This is the main reason leading to the red shift of absorption edge.
文摘Deducting interference method was applied to determine the concentration of nitrogen in the presence of Ti.This procedure is available in treating the interference of same order diffraction in EPMA.
基金V. ACKN0WLEDGMENT This work was supported by the National Natural Science Foundation of China （No.50478065） and the Excellent Youth Foundation of Anhui Province （No.04044077） to X. H. Huang, the Science and Technology Foundation of Ministry of Construction （No.05- k2-25）, the Important Foundation of Anhui Science and Technology Department （No.05022126）, and the Natural Science Foundation of Anhui Education Department （No.2006KJ139B） to Y. C. Tang.
文摘The characteristics of nitrided layers prepared on commercially pure titanium substrates by direct current nitrogen arc are presented by scanning electron microscopy （SEM） and transmission electron microscopy （TEM） micrographs as well as X-ray diffraction （ XRD ）. The titanium nitride （ TiN ） dendrites were fully developed with interconnected cellular morphologies at the top surface but grew almost perpendicular to the integrace with coarser arms in the middle area. Also less TiN was found near the interface. The energy inputs had an obvious effect on the microstructures and the hardness of the nitrided layers. The maximum micro-hardness was 2 500 HV at the top surface which was over 9 times higher than that of the substrate.
