In this work, the current understanding and development of fliction-stir welding and processing of Ti- 6Al-4V alloy are briefly reviewed. The critical issues of these processes are addressed, including welding tool ma...In this work, the current understanding and development of fliction-stir welding and processing of Ti- 6Al-4V alloy are briefly reviewed. The critical issues of these processes are addressed, including welding tool materials and design, tool wea,, processing temperature, material flow, processing window and residual stresses. A particular emphasis is given to microstructural aspects and microstructure-properties relationship. Potential engineering applications are highlighted.展开更多
The effect of post weld heat treatment on the microstructure and fracture toughness of friction welded joints of Ti-6.5Al-1Mo-1V-2Zr alloy was studied. The experimental results show that equiaxial grains were formed a...The effect of post weld heat treatment on the microstructure and fracture toughness of friction welded joints of Ti-6.5Al-1Mo-1V-2Zr alloy was studied. The experimental results show that equiaxial grains were formed at the center of the weld metal while highly deformed grains were observed in the thermomechanically affected zone. The fracture toughness of the weld metal was lower than that of the thermomechanically affected zone under as-weld and post weld heat treatment conditions. With increasing temperature of post weld heat treatment, the fracture toughness of weld center and thermomechanically affected zone increased. The fractographic observation revealed that the friction welded joints fractured in a ductile mode.展开更多
The low cycle fatigue（LCF） tests were carried out using symmetrical cyclic loading under total strain amplitude control conditions.The present paper is devoted to investigating the cyclic deformation response of Ti...The low cycle fatigue（LCF） tests were carried out using symmetrical cyclic loading under total strain amplitude control conditions.The present paper is devoted to investigating the cyclic deformation response of Ti–6Al–4V titanium and the electron-beam-welded（EBW） joint in the following aspects,i.e.,cyclic deformation behavior,fatigue life and fatigue fracture behavior.The results show that the softening of the joint is significant at larger strain ranges,while not obvious at smaller strain ranges.The joint shows shorter fatigue life at larger strain ranges and equivalent fatigue life at smaller strain ranges compared with Ti–6Al–4V base metal.A fatigue crack of the joint not only originates at the surface or subsurface,but also at defects in the fusion zone（FZ）.The crack propagation zone of Ti–6Al–4V base metal shows ductile fracture mechanism,while the joint shows brittle fracture mechanism.In all the fatigue fracture zones many dimples appear,showing the typical ductile fracture.展开更多
The effect of base material（BM） on microstructure and crystallographic orientation evolution of a Ti–6Al–4V electron-beam welded joint was investigated. Meanwhile, the crystallographic orientation of prior b grain...The effect of base material（BM） on microstructure and crystallographic orientation evolution of a Ti–6Al–4V electron-beam welded joint was investigated. Meanwhile, the crystallographic orientation of prior b grains was studied by advanced electron backscattered diffraction data processing. The inhomogeneity of microstructure within welded joint was formed due to the different microstructures of BM. By comparing microstructure details of the welded joint, including microstructure morphology and crystallographic orientation with those of the base material, it can be found that both the microstructure morphology and crystallographic orientation of the EBW joint would be controlled by BM.展开更多
文摘In this work, the current understanding and development of fliction-stir welding and processing of Ti- 6Al-4V alloy are briefly reviewed. The critical issues of these processes are addressed, including welding tool materials and design, tool wea,, processing temperature, material flow, processing window and residual stresses. A particular emphasis is given to microstructural aspects and microstructure-properties relationship. Potential engineering applications are highlighted.
基金Funded by the Commission of Science,Techonology and Industry for National Defense(No.AXXD1818)
文摘The effect of post weld heat treatment on the microstructure and fracture toughness of friction welded joints of Ti-6.5Al-1Mo-1V-2Zr alloy was studied. The experimental results show that equiaxial grains were formed at the center of the weld metal while highly deformed grains were observed in the thermomechanically affected zone. The fracture toughness of the weld metal was lower than that of the thermomechanically affected zone under as-weld and post weld heat treatment conditions. With increasing temperature of post weld heat treatment, the fracture toughness of weld center and thermomechanically affected zone increased. The fractographic observation revealed that the friction welded joints fractured in a ductile mode.
基金financially supported by the HiTech Research and Development Program of China(No.2012AA052102)the Program of International Science Technology Cooperation of China(No.2013DFA61590)
文摘The low cycle fatigue（LCF） tests were carried out using symmetrical cyclic loading under total strain amplitude control conditions.The present paper is devoted to investigating the cyclic deformation response of Ti–6Al–4V titanium and the electron-beam-welded（EBW） joint in the following aspects,i.e.,cyclic deformation behavior,fatigue life and fatigue fracture behavior.The results show that the softening of the joint is significant at larger strain ranges,while not obvious at smaller strain ranges.The joint shows shorter fatigue life at larger strain ranges and equivalent fatigue life at smaller strain ranges compared with Ti–6Al–4V base metal.A fatigue crack of the joint not only originates at the surface or subsurface,but also at defects in the fusion zone（FZ）.The crack propagation zone of Ti–6Al–4V base metal shows ductile fracture mechanism,while the joint shows brittle fracture mechanism.In all the fatigue fracture zones many dimples appear,showing the typical ductile fracture.
文摘The effect of base material（BM） on microstructure and crystallographic orientation evolution of a Ti–6Al–4V electron-beam welded joint was investigated. Meanwhile, the crystallographic orientation of prior b grains was studied by advanced electron backscattered diffraction data processing. The inhomogeneity of microstructure within welded joint was formed due to the different microstructures of BM. By comparing microstructure details of the welded joint, including microstructure morphology and crystallographic orientation with those of the base material, it can be found that both the microstructure morphology and crystallographic orientation of the EBW joint would be controlled by BM.
