Effect of interface morphology on the mechanical properties of titanium clad steel plates

Interface morphology has important influence on the bond quality of titanium clad steel plates. The mechanical properties of titanium clad steel plates with wavy and straight interfaces were investigated by tensile-shear tests and bending tests. The interface morphology of the plates was examined by optical microscopy （OM） and scanning electron microscopy （SEM）. The experimental results show that the shear strength of a wavy interface is higher than that of a straight interface. A wavy interface is the guarantee for obtaining high shear strength to provide a greater shear resistance. During the maerobending process, cracks appear in the swirl of the wave tip and ferrotitanium intermetallies. For in-situ observing the bending process by SEM, the wave tip of a wavy interface and the massive ferrotitartium intermetallies of a straight interface are places where cracks initiate and propagate. The results are the same as those observed in the macrobending process. Became of high hardness, the wave tip and the massive ferrotitanium intermetallies are hard in terms of compatible deformation.

Study on the interface of direct hot rolling titanium-clad steel plates

In this study,the interface characteristics of a direct hot rolling titanium-clad steel plate were analyzed, and the mechanism of interface cracking was explored. The detrimental effect from the formation of TiFe ,TiC,and a Si-enriched layer on the bonding strength was clarified, and an industrial-scaled titanium-clad steel plate with shear strength over 200 MPa was produced with a carefully set schedule accordingly. It was found that hot rolling titanium-clad steel plates had a flat interface without obvious cracks. In the rolling process,both Ti and Fe atoms interdiflhsed,but Fe difthsed much faster than Ti. The Fe-diffused area consisted of three regions. After a high temperature heat treatment, the diffusion depth of Fe and Ti elements increased significantly and evident Si segregation and TiFe layers were identified. Thermal cracking initiated in the Si segregation layer and then propagated along the TiFe layer and Fe-diffused layer on the titanium side.

Effect of nitrogen content on the microstructure and mechanical properties of titanium-bearing nonquenched and tempered steel after hot forging

The microstructure and mechanical properties of titanium(Ti)-bearing medium-carbon nonquenched and tempered steel with different nitrogen content before and after hot forging were investigated through smelting,forging,and laboratory tests.The results show that the grain size of nonquenched and tempered steel was gradually refined,and the ferrite content gradually increased with an increase in nitrogen content.The grain size of the material with low nitrogen content increased abnormally,and its impact properties significantly decreased after hot forging.The grain size of nonquenched and tempered steel with higher nitrogen content was slightly larger than that before forging,and the tensile and yield strength increased,but the impact toughness was not significantly reduced.The Ti-bearing nonquenched and tempered steel showed better strength and toughness after hot forging with the addition of 0.010%0.015%nitrogen.

Process Parameters Optimization of Laser Cladding for HT200 with 316L Coating Based on Response Surface Method

In order to improve the sealing surface performance of gray cast iron gas gate valves and achieve precise molding control of the cladding layer,as well as to reveal the influence of laser cladding process parameters on the morphology and structure of the cladding layer,we prepared the 316L coating on HT 200 by using Design-Expert software central composite design(CCD)based on response surface analysis.We built a regression prediction model and analyzed the ANOVA with the inspection results.With a target cladding layer width of 3.5 mm and height of 1.3 mm,the process parameters were optimized to obtain the best combination of process parameters.The microstructure,phases,and hardness variations of the cladding layer from experiments with optimal parameters were analyzed by the metallographic microscope,confocal microscope,and microhardness instrument.The experimental results indicate that laser power has a significant impact on the cladding layer width,followed by powder feed rate;scan speed has a significant impact on the cladding layer height,followed by powder feed rate.The HT200 substrate and 316L can metallurgically bond well,and the cladding layer structure consists of dendritic crystals,columnar crystals,and equiaxed crystals in sequence.The optimal process parameter combination satisfying the morphology requirements is laser power(A)of 1993 W,scan speed(B)of 8.949 mm/s,powder feed rate(C)of 1.408 r/min,with a maximum hardness of 1564.3 HV0.5,significantly higher than the hardness of the HT200 substrate.

Microstructure and high temperature tribological behavior of laser cladding Ni60A alloys coatings on 45 steel substrate

The crack-free Ni60 A coating was fabricated on 45 steel substrate by laser cladding and the microstructure including solidification characteristics, phases constitution and phase distribution was systematically investigated. The high temperature friction and wear behavior of the cladding coating and substrate sliding against GCr15 ball under different loads was systematically evaluated. It was found that the coating has homogenous and fine microstructure consisting of γ（Ni） solid solution, a considerable amount of network Ni-Ni3 B eutectics, m^23C6 with the floret-shape structure and Cr B with the dark spot-shape structure uniformly distributing in interdendritic eutectics. The microhardness of the coating is about 2.6 times as much as that of the substrate. The coating produces higher friction values than the substrate under the same load condition, but the friction process on the coating keeps relatively stable. Wear rates of the coating are about 1/6.2 of that of the substrate under the higher load（300 g）. Wear mechanism of the substrate includes adhesion wear, abrasive wear, severe plastic deformation and oxidation wear, while that of the coating is merely a combination of mild abrasive wear and moderate oxidation wear.

Interfacial structure and mechanical properties of hot-roll bonded joints between titanium alloy and stainless steel using niobium interlayer

The hot-roll bonding was carried out in vacuum between titanium alloy and stainless steel using niobium interlayer. The interfacial structure and mechanical properties were analyzed. The results show that the plasticity of bonded joint is improved significantly. When the bonding temperature is 800 °C or 900 °C, there is not intermetallic layer at the interface between stainless steel and niobium. When the bonding temperature is 1000 °C or 1050 °C, Fe-Nb intermetallic layer forms at the interface. When the bonding temperature is 1050 °C, cracking occurs between stainless steel and intermetallic layer. The maximum strength of -417.5 MPa is obtained at the bonding temperature of 900 °C, the reduction of 25% and the rolling speed of 38 mm/s, and the tensile specimen fractures in the niobium interlayer with plastic fracture characteristics. When the hot-roll bonded transition joints were TIG welded with titanium alloy and stainless steel respectively, the tensile strength of the transition joints after TIG welding is -410.3 MPa, and the specimen fractures in the niobium interlayer.

Effect of intermetallic compounds on heat resistance of hot roll bonded titanium alloy-stainless steel transition joint

The effect of intermetallic compounds on the heat resistance of transition joint was investigated. The experiment of post-weld heat treatment for the hot roll bonded titanium alloy-stainless steel joint using nickels interlayer was carried out, and the interface microstructure evolution due to heat treatment was presented. There was not found significant interdiffusion at stainless steel/nickel interface, when the specimens were heat treated in the temperature range of 600-800 °C for 10 and 30 min, while micro-cracks occurred at the stainless steel/nickel interface heat treated at 700 °C for 30 min. The thickness of intermetallic layers at nickel/titanium alloy interface increased at 600 °C, and micro-cracks occurred at 700 and 800 °C. The micro-cracks occurred between intermetallic layers or between intermetallic layer and nickel interlayer as well. The tensile strength of the transition joint decreased with the increase of heat treatment temperature or holding time.

Influences of different filler metals on electron beam welding of titanium alloy to stainless steel

Electron beam welding experiments of titanium alloy to stainless steel were carried out with different filler metals, such as Ni, V, and Cu. Microstructures of the joints were examined by optical microscopy, scanning electron microscopy and X-ray diffraction analysis. Mechanical properties of the joints were evaluated according to tensile strength and microhardness. As a result, influences of filler metals on microstructures and mechanical properties of electron beam welded titanium-stainless steel joints were discussed. The results showed that all the filler metals were helpful to restrain the Ti-Fe intermetallics. The welds with different filler metals were all characterized by solid solution and interfacial intermetallics. For each type of the filler metal, the type of solid solution and interfacial intermetallics depended on the metallurgical reactions between the filler metals and base metals. The interfacial intermetallics were Fe2Ti＋Ni3Ti＋NiTi2, TiFe, and Cu2Ti＋CuTi＋CuTi2 in the joints welded with Ni, V, and Cu filler metals, respectively. The tensile strengths of the joints were dependent on the hardness of the interfacial intermetallics. The joint welded with Ag filler metal had the highest tensile strength, which is about 310 MPa.

Microstructure and formation mechanism of titanium matrix composites coating on Ti-6Al-4V by laser cladding

Laser cladding experiments were done on a 5-kW continuous wave CO2 laser to synthesize TiC and TiB rein- fowed titanium matrix composite coatings on Ti-6AI-4V alloy with a mixture of Ti and B4C precursor powder. The ther- modynamics of the reactions were calculated and analyzed. The microstructure and phase evolution of TiB and TiC com- posites were investigated. The results showed that the chemical reaction between Ti and B4C would release much heat, and these compounds, TiC, TiB, and small amount of TiB2, can be formed on the surface of Ti-6AI-4V alloy if the supplied en- ergy is sufficient to excite the reaction among the initial products. A good metallurgical bond between the coating and the substrate can be achieved. The microhardness of coating was irregular and the maximum value was approximately HV600.

LASER CLADDED TiCN COATINGS ON THE SURFACE OF TITANIUM

Laser cladded coatings of TiCN were produced on the surface of titanium. To obtain the optimal techniques, several conditions were tested by varying the laser scanning rate. The choice of shielding gas was also studied. The cladded coatings were then evaluated from the surface mechanics point of view based on their microhardness. The microstructure of some interesting samples was investigated by optical micrographs （OM）. The results showed that under the condition of fixed pulse frequency and pulse width, the laser scanning rate and the shielding gas are the main factors influencing the components of coatings. TiCN coatings were decompounded and oxidized during the cladding process in the condition of no shielding gas of N2. X-ray diffraction results indicated that the composite coatings composed of TiCN, TiC, Ti2N, and TiO2 were produced using appropriate techniques. The results indicated that the best condition in terms of the surface microhardness is obtained when the scanning rate is 1.5mm/s, the pulse frequency is 15Hz, the pulse width is 3.0ms, and N2 is chosen as the shielding gas. The microhardness of the composite coatings is about 1331kg · mm^-2, which is about 4 times that of the substrate. The optical micrographs indicated that the cladding zone is made up of TiCN, TiO2 and some interdendritic Ti, but the diffusion zone mainly consists of the dendrites phase, and the cladded depth is about 80μm, which is more than 2 times that of the laser nitrided sample. There were no microcracks or air bubbles in the cladded sample, which was cladded using the above optimal techniques.

Microstructures of brazing zone between titanium alloy and stainless steel using various filler metals

Titanium alloy (Ti-Al-V alloy) substrate was brazed with stainless steel (STS304) using filler metal.At an optimized brazing condition,various filler metals were used.Microstructures were observed at each condition.Filler metals were titanium based 40Ti-20Zr-20Cu-20Ni,silver based Ag 5Pd,and nickel based Ni-7Cr-3.1B-4.5Si-3Fe-0.06C (BNi2) and Ni-14Cr-10P-0.06C (BNi7).To select a good filler metal for brazing process,wetting test was performed at 880-1050 °C.It was not brazed using silver based filler metals,but at the conditions using titanium and nickel based filler metals had brazed zone between titanium alloy and stainless steel.However,titanium alloy was eroded during brazing using titanium based filler metals.Nickel based filler metal has a good brazed zone between titanium alloy and stainless steel among the filler metals.

Wear and corrosion resistance of laser-cladded Fe-based composite coatings on AISI 4130 steel

The wear and corrosion resistance of Fe_（72.2）Cr_（16.8）Ni_（7.3）Mo_（1.6）Mn_（0.7）C_（0.2）Si_（1.2） and Fe_（77.3）Cr_（15.8）Ni_（3.9）Mo_（1.1）Mn_（0.5）C_（0.2）Si_（1.2） coatings laser-cladded on AISI 4130 steel were studied.The coatings possess excellent wear and corrosion resistance despite the absence of expensive yttrium,tungsten,and cobalt and very little molybdenum.The microstructure mainly consists of dendrites and eutectic phases,such as duplex（γ＋α）-Fe and the Fe–Cr（Ni）solid solution,confirmed via energy dispersive spectrometry and X-ray diffraction.The cladded Fe-based coatings have lower coefficients of friction,and narrower and shallower wear tracks than the substrate without the cladding,and the main wear mechanism is mild abrasive wear.Electrochemical test results suggest that the soft Fe_（72.2）Cr_（16.8）Ni_（7.3）Mo_（1.6）Mn_（0.7）C_（0.2）Si_（1.2） coating with high Cr and Ni concentrations has high passivation resistance,low corrosion current,and positive corrosion potential,providing a better protective barrier layer to the AISI 4130 steel against corrosion.

Delayed Fracture Behavior of CrMo-Type High Strength Steel Containing Titanium

The delayed fracture behaviors of CrMo-type high strength steels containing different amount of titanium(0to 0.10%)were studied.The steels were quenched at 880℃ and tempered from 400℃ to 650℃,and a wide range of tensile strength was obtained.The sustained load tensile test was carried out by using notched tensile specimens in Walpole solution.The experimental results showed that with higher strength,the Ti-microalloyed steels show higher resistance to delayed fracture compared with non-microalloyed steel due to titanium beneficial role and microstructure changes.The undissolved TiC is uniformly distributed as strong hydrogen traps,retarding or preventing the diffusion and accumulation of hydrogen to lower-interaction energy sites,such as prior austenite and martensite lath boundaries in stress concentration area.Meanwhile,the grain refining effect of titanium is also an important factor to improve the delayed fracture resistance of Ti-microalloyed steels.The characteristics of delayed fracture remain nearly the same with titanium addition.

Research progress of laser cladding self-fluxing alloy coatings on titanium alloys

Laser cladding is a new surface modification technology, and is widely used for fabricating wear and corrosion resistant composites coatings. Self-fluxing alloys have many advantages, such as excellent properties of deoxidizing and slagging, high wear resistance, low melting point and easy cladding, and are often used in laser cladding to improve wear and corrosion resistance of titanium and its alloys. In this paper, the recent development of Ni-based and Co-based self-fluxing alloy coatings which includes the influenee of rare earth and ceramic particles in coatings are summarized. Besides, the effects of processing parameters, such as laser power and scanning speed, on coatings are reviewed. Finally, the trend of development in the future is forecasted.

Characterization of Fe_3Si-based coatings on low silicon steel by pulsed Nd:YAG laser cladding

The Fe3Si based coating was produced on the Fe-1 Si steel surface by a pulsed Nd：YAG （yttrium aluminum garnet） laser. Its phase constitution and microstructure were characterized by using X-ray diffraction （XRD）, optical microscope （OM）, and field emission scanning electron microscope （FESEM） with associated energy dispersive spectroscopy （EDS） and transmission electron microscopy （TEM）. The hyperfine structure of the coating was studied by Mrssbauer spectra （MS） and the magnetic property was also measured at room temperature by a vibrating sample magnetometer （VSM）. The obtained coating is pore and crack-free with dense microstructure and high Si content. The metallurgical bonding between the coating and the substrate was realized. The microstructure of the coating is typical fine dendrites. The major phase was confirmed by XRD and TEM to be the ordering D03 structured Fe3Si phase. In addition, there were smaller amounts of the Fe5Si3 phase and the γ-Fe phase in the coating. Compared with the substrate, the laser cladding coating has a lower saturation magnetization and a higher coercive force. The poor magnetic property might be because of rapid solidification microstructure and phase constitution in the coating.

Microstructure,properties and first principles calculation of titanium alloy/steel by Nd: YAG laser self-fluxing welding

The experiment of Nd： YAG pulsed laser self-fluxing welding for 304 stainless steel/Ti6Al4V titanium alloy dissimilar metal was carried out. The microstructure properties of welded joint were analyzed by SEM, EDS and XRD. The equilibrium lattice constants, enthalpies of formation, cohesive energies, mechanical properties, Debye temperatures and valence electron structures of Ti-Fe intermetallic compounds （IMCs） were calculated by the first principle pseudopotential plane wave method based on density functional theory （DFT）. According to the thermodynamic data of Ti-Fe-Cr compounds, the Gibbs free energy per mole of compound at different temperatures was calculated and their thermal stability was compared. The results show that there are no macroscopic cracks in the welded joints, and the IMCs distributed evenly along the welding interface exhibits 3 distinct layers of microstructure with different colors. The welds interface generates IMCs of TiFe, TiFe 2 and a small amount of Ti 5Cr 7Fe 17 IMCs. Ti-Fe IMCs with high thermodynamic stability and easy alloying formation. The results of Gibbs free energies show that the sequence of precipitates in the interface is Ti 5Cr 7Fe 17 , TiFe 2 and TiFe in high temperature during the metallurgical reaction. The G/B values of Ti-Fe IMCs are greater than the critical value of 0.5, indicating that it is an intrinsic brittleness.

Pulsed Nd:YAG laser cladding of high silicon content coating on low silicon steel

A pulsed Nd：YAG （yttrium aluminum garnet） laser-based technique was employed to clad low silicon steel with preplaced Si and Fe mixed powders for high Si content. The surface morphology, microstructural evolution, phase composition, and Si distribution, within the obtained cladding coatings, were characterized by optical microscopy （OM）, field emission scanning electron microscopy （FE-SEM）, with associated energy dispersive spectroscopy （EDS）, transmission electron microscopy （TEM）, and X-ray diffraction （XRD）. The microhardness was also measured along the depth direction of the specimens, A crack- and pore-free cladding coating through excellent metallurgical bonding with the substrate was successfully prepared on low silicon steel by means of optimized single-track and multi-track laser cladding. The phases of the coating are a-Fe, T-Fe, and FeSi. The high microhardness of the lasercladding zone is considered as an increase in Si content and as the refined microstructure produced by the laser treatment. The Si contents of the cladding coatings were about 5.8wt% in the single-track cladding and 6.5wt% in the multi-track cladding, respectively.

Effects of aluminum and titanium on the microstructure of ODS steels fabricated by hot pressing

Three oxide-dispersion-strengthened(ODS)steels with compositions of Fe-14Cr-2W-0.2V-0.07Ta-0.3Y_2O_3(wt%,so as the follows)(14Y),Fe-14Cr-2W-0.2V-0.07Ta-1Al-0.3Y_2O_3(14YAl),and Fe-14Cr-2W-0.2V-0.07Ta-0.3Ti-0.3 Y_2O_3(14YTi)were fabricated by hot pressing.Transmission electron microscopy(TEM)was used to characterize the microstructures and nanoparticles of these ODS steels.According to the TEM results,14Y,14YAl,and 14YTi ODS steels present similar bimodal structures containing both large and small grains.The addition of Al or Ti has no obvious effect on the microstructure of the steels.The spatial and size distribution of the nanoparticles was also analyzed.The results indicate that the average size of nanoparticles in the 14YTi ODS steel is smaller than that in the 14YAl ODS steel.Nanoparticles such as Y_2O_3,Y_3Al_5O_(12) and YAlO_3,and Y_2Ti_2O_7 were identified in the 14Y,14YAl,and 14YTiODS steels,respectively.

Microstructure,strength and welding window of aluminum alloy-stainless steel explosive cladding with different interlayers

Aluminum 5052(Al 5052)-stainless steel 316(SS 316)plates were explosively cladded with Al 1100,pure copper and SS 304 interlayers.The operational parameters viz.,standoff distance,explosive mass ratio(mass ratio of the explosive to the flyer plate)and inclination angle were varied and the results were presented.The advent of interlayer relocates the lower boundary of the welding window,and enhances the welding regime by 40%.A triaxial welding window,considering the influence of the third operational parameter,was developed as well.Use of interlayer transforms the continuous molten layer formed in the traditional Al 5052-SS 316 explosive clad interfaces into a smooth interface devoid or with a slender presence of intermetallic compounds.The microhardness,ram tensile and shear strengths of the interlayered clads are higher than those of the traditional explosive clads,and the maximum values are witnessed for stainless steel interlaced Al 5052-SS 316 explosive clads.

A STUDY OF CONTINUOUS EXTRUSION-CLADDING PROCESSFOR PRODUCTION OF ALUMINUM-CLADDING STEEL WIRE

In this study the process of cladding steel wires with aluminum is investigated experimentally. It is studied how the cladding process and the quality of products are influenced by the aluminum deformation temperature, the wheel speed, the temperature of steel wire, the wire speed and the steel wire tensile force. The relation among the process parameters above is discussed, and the effect of the aluminum deformation temperature on the coating microstructure is analyzed. This paper suggested a reasonable range of process parameters for producing aluminum cladding steel wires.