Viscosity and Viscosity Estimate Model of Fluoride-Free and Titanium-Bearing Mold Fluxes

The relationship between the binary basicity （CaO/SiO2）,TiO2,Na2O,Li2O,MgO,MnO,B2O3 and viscosity for fluoride-free and titanium-bearing mold fluxes were systematically researched. The rotating cylinder method was employed in the experiment to measure the viscosity of the slag. The results indicate that Li2O, B2O3 and Na2O play major roles in decreasing viscosity, especially Li2O, which is the most effective flux, while MgO and MnO exert little influence on viscosity. Meanwhile, it can be concluded that with increasing TiO2 content, the viscosity of fluoride-free and titanium-bearing mold fluxes increases at first but then falls when the amount of TiO2 is greater than 6.0%. Based on large amounts of experimental statistics of the viscosity of fluoride-free and titanium-bearing mold fluxes, an available model in literature for predicting the mold-slag viscosity was modified. This modified model can be used to predict the viscosity of fluoride-free and titanium-bearing mold fluxes. In fact, the predicted values approximate the observed values with a ±10.6% average deviation. Compared with the classical models,the average deviation is higher and it was found that the modified model can be used to estimate the viscosity of fluoride-free and titanium-bearing mold fluxes.

Influence of substituting B_(2)O_(3) with Li_(2)O on the viscosity,structure and crystalline phase of low-reactivity mold flux

The low-reactivity mold flux with low SiO_(2)content is considered suitable for the continuous casting of high-aluminum steel since it can significantly reduce the reaction between Al in steel and SiO_(2)in mold flux.However,the traditional low-reactivity mold flux still presents some problems such as high viscosity and strong crystallization tendency.In this study,the co-addition of Li_(2)O and B_(2)O_(3)in CaO–Al_(2)O_(3)–10wt%Si O_(2)based low-reactivity mold flux was proposed to improve properties of mold flux for high-aluminum steel,and the effect of Li_(2)O replacing B_(2)O_(3)on properties of mold flux was investigated.The viscosity of the mold flux with 2wt%Li_(2)O and 6wt%B_(2)O_(3)reached a minimum value of 0.07 Pa·s.The break temperature and melting point showed a similar trend with the viscosity.Besides,the melt structure and precipitation of the crystalline phase were studied using Raman and X-ray diffraction spectra to better understand the evolution of viscosity.It demonstrated that with increasing Li_(2)O content in the mold flux from 0 to 6 wt%,the degree of polymerization of aluminate and the aluminosilicate network structure increased because of increasing Li+released by Li_(2)O,indicating the added Li_(2)O was preferentially associated with Al^(3+)as a charge compensator.The precipitation of LiAlO_(2)crystalline phase gradually increased with the replacement of B_(2)O_(3)by Li_(2)O.Therefore,Li_(2)O content should be controlled below 2wt%to avoid LiAlO_(2)precipitation,which was harmful to the continuous casting of highaluminum steels.

Dissolution of TiO_(2) and TiN inclusions in CaO–SiO_(2)–B_(2)O_(3)-based fluorine-free mold flux

Mold flux serves the crucial metallurgical function of absorbing inclusions, directly impacting the smoothness of the casting process as well as the cast slab quality. In this study, the dissolution behavior and mechanism of Ti O_(2)and Ti N inclusions in molten Ca O–Si O_(2)–B_(2)O_(3)-based fluorine-free mold flux were explored by in situ single hot thermocouple technology combined with X-ray photoelectron spectroscopy.The results showed that Ti O_(2) inclusions are effectively dissolved by the molten slag within 76 s, during which the original octahedral [Ti O_(6)]^(8-)structures are destroyed and convert to the networker tetrahedral [Ti O_(4)]^(4-)structures. However, the dissolution rate is much lower for Ti N inclusions than for Ti O_(2)inclusions. This can be attributed to the fact that the Ti N particles need to be oxidized and then dissolved in the molten slag to form tetrahedral [Ti O4]4-and octahedral [Ti O_(6)]^(8-)structures during the Ti N inclusion dissolution process, which is accompanied by the generation of a large amount of N_(2)gas. Moreover, Ca Ti O_(3)crystals tend to nucleate and grow on bubble surfaces with sufficient octahedral [Ti O_(6)]^(8-)structures and Ca^(2+)ions, eventually resulting in the molten slag being in a solid–liquid mixed state.

Crystallization Temperature and Crystallization Ratio of Mold Flux

The factors influencing the crystallization ratio of mold flux were researched by rapid cooling technolo gy, and the factors affecting crystallization temperature were studied by single thermocouple technique. The results showed that the crystallization ratio of mold flux increases with the basicity and the content of Na2O, CaF2, Li2O and NaF, and decreases with the increase of the content of Al2O3, MgO, BaO, MnO and B2O3. However, the crystallization temperature of mold flux rises with the basicity and the content of NaF, Na2O and CaF2, and reduces with the increase of the content of Al2O3, MgO, BaO, MnO and B2O3. But for Li2O, crystallization temperature decreases firstly to a minimum value at 2%, and then increases gradually with the increase of Li2O.

Effect of CeO_2 on heat transfer and crystallization behavior of rare earth alloy steel mold fluxes

To improve the heat transfer capability and the crystallization property of the traditional mold flux, CaF_2 was replaced with B_2O_3. Then, the influences of CeO_2 on the heat transfer and the crystallization of the CaF_2-bearing mold flux and the new mold flux with 10 wt% B_2O_3 were studied using a slag film heat flux simulator and X-ray diffraction(XRD). The results revealed that the addition of CeO2 reduced the heat transfer by increasing the solid slag thickness and the crystallization of two mold fluxes. However, CeO_2 had less effect on the B_2O_3-containing mold flux compared with the CaF_2-bearing mold flux. According to the analyses, the CeO_2 contents in the CaF_2-bearing mold flux and the B_2O_3-containing mold flux should not exceed 8 wt% and 12 wt%, respectively. Therefore, these experimental results are beneficial to improve and develop the mold flux for casting rare earth alloy steels.

Research on mold flux for hypo-peritectic steel at high casting speed

Mold fluxes having adaptable properties were developed in the laboratory to solve quality defects, such as depressions and longitudinal cracks when casting hypo-peritectic steel at high casting speed. Firstly, the effect of components on the high basicity mold flux properties was first studied using the orthogonal method. In the scope of the studied content, Li2O has the largest effect on the melting temperature, and the least effect on the viscosity; CaF2 has the largest effect on the viscosity, and the least effect on the melting temperature; Na2O and CaO/SiO2 have no obvious influence on the melting temperature and viscosity. Secondly, two powders （Z1 and Z6） have reasonable viscosity-temperature curves, higher solidification temperatures, and porous structure after solidification, but the crystal property of Z6 is worse than that of Z1, and thus Z1 is more suitable for continuous casting hypo-peritectic steel at high casting speed. Thirdly, a higher basicity of powder, a less free enthalpy of crystal compound, and a lower baffle energy are good for a higher tendentiousness of crystal.

Shear-thinning behavior of the CaO–SiO2–CaF2–Si3N4 system mold flux and its practical application

Satisfying the mold-flux performance requirements for high-speed continuous casting necessitates the development of a new non-Newtonian-fluid mold flux with shear-thinning behavior, i.e., a mold flux whose viscosity is relatively high under lower shear rates and relatively low under higher shear rates. In this work, a mold flux that exhibits shear-thinning behavior was developed by adding different amounts of Si_3N_4 to the CaO–SiO_2–CaF_2 mold flux. The shear-thinning behavior was investigated using a rotational viscometer. In addition, the microstructure of the newly prepared slags was studied by high-temperature Raman spectroscopy and X-ray photoelectron spectroscopy. The results showed that the mechanism of shear-thinning was attributable to a temporary viscosity loss caused by the one-way shear stress, whereas the corresponding magnitude of shear-thinning was closely related to the degree of polymerization(DP). Finally, the non-Newtonian fluid mold flux was used for laboratory casting tests, which revealed that the mold flux could reduce slag entrapment and positively affect the continuous casting optimization.

Effect of Carbon Properties on Melting Behavior of Mold Fluxes for Continuous Casting of Steels

During continuous casting of steel, the properties of mold fluxes strongly affect the casting performance, steel quality and environment of casting operation. The high temperature microscopy technique was used to investigate the melting behaviour of mold fluxes, and drip test method was used to determine their melting rate. The results showed that free carbon is a dominant factor in governing the melting behaviour of fluxes, and the melting rate is increased with increasing carbon reactivity and decreasing carbon content.

Crystallization behavior of F-free mold fluxes

The time-temperature-transformation （TTT） diagrams of F-free mold fluxes was constructed using single hot thermocouple technique （SHTT） and confocal scanning laser microscopy （CSLM） to study the crystallization behavior of F-free mold fluxes. The tendency of crystallization is found to increase whereas the incubation time decreases with increasing basicity. Zirconia addition enhances the crystallization tendency due to its limited solubility in the slag melt and the solid particles acting as nucleation sites. Pseudo-wollastonite is found to precipitate in the slag with low basicity （CS-1 and CS-2）, kilchoanite and larnite are formed with further increasing basicity （CS-3）, and larnite is finally formed as the basicity beyond unit （CS-4）. The crystal morphology changes with varying compositions and isothermal temperatures. The measured growth rate is found to be linear with time under isothermal conditions and decreases with increasing isothermal temperature.

Solidification and crystallization properties of CaO-SiO_2-Na_2O based mold fluxes

Crystallization properties play an important role in keeping a smooth running of continuous casting process and high surface quality of cast strands. To reduce fluorine pollution in slag, a new type of CaO-SiO2-Na2O （CSN） based mold flux was studied. The solidification and crystallization properties, including crystallization temperature, crystallization ratio and solidification mineragraphy, were measured, which were compared with the CaO-SiO2-CaF2 （GF） mold flux. The results show that the crystallization performance is equal to the high fluoride mold powder and CSN can be used for peritectic steel grades sensitive to longitudinal cracking in continuous casting.

Effects of Rare Earth Oxide on Viscosity of Mold Fluxes for Continuous Casting

The effects of RE (rare earth) oxide on viscosity of mold fluxes were investigated with a rotary viscometer. The results show that: (1) The viscosity of mold fluxes is remarkably increased by RE oxide addition, especially when the mass fraction of RE oxide is more than 10%. (2) By addition of RE oxide, precipitation of the insoluble particles with high melting point from the molten slag with the decreasing of the temperature leads to the increase of viscosity. Viscosity curve shows that RE oxide is soluble in some extent in mold fluxes. When RE oxide is in a state of supersaturation, the existence of insoluble particles also makes the viscosity of mold fluxes increase. (3) Not only the viscosity of mold fluxes can be reduced, but also the capacity to dissolve and absorb RE oxide can be increased by Li_2O, B_2O_3 and BaO. However, the contents of Li_2O, B_2O_3, and BaO should be controlled to suitable levels. (4) The solidification temperature of mold fluxes can be increased by the addition of RE oxide, which is unfavorable to heat transfer and lubrication of mold fluxes between steel shell and mold.

Mold flux entrainment mechanisms

This paper presents a comprehensive and critical review of mold flux entrainment mechanisms in continuous casting of steel.Entrainment introduces inclusions into the final product,and thus greatly hinders clean steel production.By understanding the mechanisms that cause entrainment,the operating conditions of casters can be tuned to reduce the number of defects.Nine different mechanisms have been proposed over the last three decades,including vortex formation around the submerged entry nozzle(SEN),argon bubble interactions with the slag layer,shear-layer instability at the slag-steel interface,excessive upward flow impingement upon the meniscus, top surface level fluctuations,meniscus freezing and hook formation,top surface "balding",top surface standing wave instability,and slag crawling down the SEN.The previous work done for each of these mechanisms is presented,including both quantitative and qualitative descriptions of their behavior.

FACTORS ON VISCOSITY STABILITY OF MOLD FLUXES

Viscosity stability indexes of mold flux at high temperature and low temperature havebeen introduced and the effects of flux compositions on viscosity stability indexeshave been studied. Two mold fluxes have been developed by analyzing the effects offlux viscosity stability on the process and the condition of continuous casting slab ofmedium carbon steel. The results show that the fluxes are suitable for the process.

Distribution of Magnetic Flux Density in Soft-Contact EMCC Rectangular Mold

The distribution of the magnetic flux density in a soft-contact electromagnetic continuous casting （EMCC） rectangular mold was investigated. The experimental results show that with an increase in electric power, the magnetic flux density increases. The position where the maximum magnetic flux density appears will shift up when the coil moves to the top of the mold. At the same time, the maximum magnetic flux density will increase and the effective acting range of electromagnetic pressure will widen. As a result, in practice, the coil should be placed near the top part of the mold. The meniscus should be controlled near the top part of the coil, as this not only remarkably improves the billet surface quality but also saves energy. With the same electric power input, the higher the frequency, the lower the magnetic flux density.

The optimization of mold fluxes used for casting the peritectic steel of heavy slabs at Baosteel

In order to solve the problem of the high surface longitudinal crack ratio of heavy peritectic steel slabs produced by the No. 3 continuous caster at Baosteel,the physical properties of the original mold flux and the optimized mold flux were compared in a comprehensive way by using analytical measures, such as a slag film heat-flow simulator, a thermowire molten flux crystallization tester and an X-ray diffractometer in the laboratory. The results reveal that one of the major reasons for the cracks is the poor heat transfer ability of the original mold flux. However, the optimized mold flux with a high basicity features a high crystallizing rate,low crystallization temperature and low heat-flow density. Therefore, the optimized mold flux is more suitable for casting peritectic steel by the heavy slab continuous caster. The test results show that the slabs produced by using the optimized mold flux had no surface longitudinal crack in four test casts, while the surface longitudinal crack ratio of the slabs produced by using the original mold flux was 5%. The optimized mold flux can effectively prevent slab surface longitudinal cracks from occurring.

Wetting behavior of CaO-Al_(2)O_(3)-based mold flux with various BaO and MgO contents on the steel substrate

The Interfacial phenomena in mold have a great impact on the smooth operation of continuous casting process and the quality of the casting product.In this paper,the wetting behavior of CaO-Al_(2)O_(3)-based mold flux with different BaO and MgO contents was studied.The results showed that the contact angle between molten flux and interstitial free(IF)steel substrate increased from 62.4°to 74.5°with the increase of BaO content from 3 wt%to 7 wt%,while it decreased from 62.4°to 51.3°with the increase of MgO content from 3 wt%to 7 wt%.The interfacial tension also increased from 1630.3 to 1740.8 mN/m when the BaO content increased,but it reduced from 1630.3 to 1539.7 mN/m with the addition of MgO.The changes of contact angle and interfacial tension were mainly due to the fact that the bridging oxygen(O^(0)) at the interface was broken into non-bridging oxygen(O^(-)) and free oxygen(O_(2-)) by MgO.However,more O^(-) and O_(2-) connected into O^(0) when BaO was added,since the charge compensation effect of BaO was so stronger that it offset the effect of providing O_(2-).

钛渣熔体结构及传输性质分子动力学模拟研究进展

高品位钛渣(TiO_(2)含量≥90%)的高效制备不仅是高品质钛产品生产的关键,而且已成为我国钛冶金行业发展的迫切需要。钛铁矿还原熔炼过程钛渣熔体传输性质的调控是实现高品位钛渣高效制备的关键。国内外学者采用分子动力学模拟的方法,开展钛渣熔体结构演变及传输性质的研究,取得了显著的进展,证实了分子动力学模拟的方法在钛渣熔体研究中的有效性。分子动力学模拟的方法在研究钛渣熔体结构和性质方面具有显著的优势,不但能考察钛渣熔体结构参数、传输性质及相关微观细节,而且不受试验条件(高温、高腐蚀性、高化学活性)的限制。通过分子动力学模拟能够获取钛渣熔体丰富的结构信息和重要的传输性质,避免了钛渣熔体结构及物理性质试验测试中存在的难题。最后,结合冶金熔体成分和结构的复杂性,总结存在的问题,对分子动力学模拟在熔体结构及传输性质研究中的应用进行了展望。

超低碳IF钢冶炼过程炉渣对夹杂物控制研究进展

超低碳IF钢板主要应用于汽车面板等超深冲部件,其面临的主要质量问题是夹杂物、卷渣、气泡造成的炼钢缺陷,因此全生产流程中所采用的炉渣性质对控制炼钢缺陷具有重要作用。分别从炉渣的物化特性以及所在工序炉渣特性两个角度归纳总结了炉渣对夹杂物控制产生的影响,发现炉渣对夹杂物的吸附溶解与炉渣的物化性质和夹杂物的尺寸相关。RH精炼渣主要控制目标是低氧化性和合适的w(CaO)/w(Al_(2)O_(3)),TFe质量分数一般控制在2.0%~8.0%,w(CaO)/w(Al_(2)O_(3))控制在1.2~1.8,此外精炼渣碱度一般控制较高为4.0~10.0。中间包覆盖剂和结晶器保护渣首先要防止钢液增碳,其次是防止渣中SiO_(2)造成钢液的二次氧化,同时它们还应拥有良好的吸附夹杂物的能力。超低碳IF钢中间包高碱度覆盖剂一般碱度为2.9~11.5,w(CaO)/w(Al_(2)O_(3))控制在1.0~2.5,(FeO+MnO)质量分数控制在1.9%~4.0%。而超低碳IF钢结晶器保护渣的碱度一般控制较低在0.85~1.0,w(CaO)/w(Al_(2)O_(3))控制在5.0~8.5,(FeO+MnO)质量分数小于1%。

B_(2)O_(3)对CaO-Al_(2)O_(3)-B_(2)O_(3)三元保护渣熔体结构的影响

通过分子动力学方法对非反应性保护渣CaO-Al_(2)O_(3)-B_(2)O_(3)三元渣系进行了模拟,构建了熔渣的网络结构模型,研究了渣系中B_(2)O_(3)的含量对保护渣熔渣微观结构的影响规律。结果表明:B在网络中与O的结合能力最强,且能够起到简化网络和平衡过剩电荷的作用;Al在熔体中主要以4配位形式存在,同时存在少量高配位Al-O结构,B_(2)O_(3)的含量为5%时,熔渣中[AlO_(4)]含量最高;随着B_(2)O_(3)含量的增多,熔渣网络结构聚合程度降低,复杂Al-O结构减少,熔渣微结构的有序性增加。