In this investigation,the effect of friction stir welding(FSW)parameters such as tool pin profiles,rotational speed and welding speed on the mechanical properties of tensile strength,hardness and impact energy of magn...In this investigation,the effect of friction stir welding(FSW)parameters such as tool pin profiles,rotational speed and welding speed on the mechanical properties of tensile strength,hardness and impact energy of magnesium alloy AZ31 was studied.The experiments were carried out as per Taguchi parametric design concepts and an L9 orthogonal array was used to study the influence of various combinations of process parameters.Statistical optimization technique,ANOVA,was used to determine the optimum levels and to find the significance of each process parameter.The results indicate that rotational speed(RS)and transverse speed(TS)are the most significant factors,followed by tool pin profile(PF),in deciding the mechanical properties of friction stir welded magnesium alloy.In addition,mathematical models were developed to establish relationship between different process variables and mechanical properties.展开更多
Joints between two different grades of aluminium alloys are need of the hour in many light weight military structures.In this investigation,an attempt has been made to join the heat treatable(AA 6061) and non-heat tre...Joints between two different grades of aluminium alloys are need of the hour in many light weight military structures.In this investigation,an attempt has been made to join the heat treatable(AA 6061) and non-heat treatable(AA 5086) aluminium alloys by friction stir welding(FSW)process using three different tool pin profiles like straight cylindrical,taper cylindrical and threaded cylindrical.The microstructures of various regions were observed and analyzed by means of optical and scanning electron microscope.The tensile properties and microhardness were evaluated for the welded joint.From this investigation it is founded that the use of threaded pin profile of tool contributes to better flow of materials between two alloys and the generation of defect free stir zone.It also resulted in higher hardness values of 83 HV in the stir zone and higher tensile strength of 169 MPa compared to other two profiles.The increase in hardness is attributed to the formation of fine grains and intermetallics in the stir zone,and in addition,the reduced size of weaker regions,such as TMAZ and HAZ regions,results in higher tensile properties.展开更多
Friction stir welding using the tools with polygonal pins is often found to improve the mechanical strength of weld joint in comparison to the tools with circular pins. However, the impacts of pin profile on the peak ...Friction stir welding using the tools with polygonal pins is often found to improve the mechanical strength of weld joint in comparison to the tools with circular pins. However, the impacts of pin profile on the peak temperature, tool torque and traverse force, and the resultant mechanical stresses experienced by the tool have been rarely reported in a systematic manner. An estimation of the rate of heat generation for the tools with polygonal pins is challenging due to their non-axisymmetric cross-section about the tool axis. A novel methodology is presented to analytically estimate the rate of heat generation for the tools with polygonal pins. A three-dimensional heat transfer analysis of friction stir welding is carried out using finite element method. The computed temperature field from the heat transfer model is used to estimate the torque, traverse force and the mechanical stresses experienced by regular triangular, square, pentagon and hexagon pins following the principles of solid mechanics. The computed results show that the peak temperature experienced by the tool pin increases with the number of pin sides. However, the resultant maximum shear stress experienced by the pin reduces from the triangular to hexagonal pins.展开更多
In order to prevent unwanted excited vibrations and to secure better machining precision in large size heavy duty machine tools dynamic stiffness is one of the most desirable and critical properties. In the past decad...In order to prevent unwanted excited vibrations and to secure better machining precision in large size heavy duty machine tools dynamic stiffness is one of the most desirable and critical properties. In the past decades, many researches on machine tool stiffness test and evaluation methodology have been made. However any methodology for a Pin Turning Device (PTD), which is a special kind of turning lathe for machining big size crankshaft pins, is rarely found among them. This study proposes a test and evaluation process of stiffness of a PTD by measuring frequency response function at the tool center point (TCP). For conformance proving for the proposed methodology, stiffness of a PTD obtained by the proposed method with impact hammer test (IHT) has been compared with that determined by FEM.展开更多
文摘In this investigation,the effect of friction stir welding(FSW)parameters such as tool pin profiles,rotational speed and welding speed on the mechanical properties of tensile strength,hardness and impact energy of magnesium alloy AZ31 was studied.The experiments were carried out as per Taguchi parametric design concepts and an L9 orthogonal array was used to study the influence of various combinations of process parameters.Statistical optimization technique,ANOVA,was used to determine the optimum levels and to find the significance of each process parameter.The results indicate that rotational speed(RS)and transverse speed(TS)are the most significant factors,followed by tool pin profile(PF),in deciding the mechanical properties of friction stir welded magnesium alloy.In addition,mathematical models were developed to establish relationship between different process variables and mechanical properties.
基金the support extended by the Centre for Materials Joining & Research (CEMAJOR), Department of Manufacturing Engineering, Annamalai University, Annamalai Nagar, India to carry out this research
文摘Joints between two different grades of aluminium alloys are need of the hour in many light weight military structures.In this investigation,an attempt has been made to join the heat treatable(AA 6061) and non-heat treatable(AA 5086) aluminium alloys by friction stir welding(FSW)process using three different tool pin profiles like straight cylindrical,taper cylindrical and threaded cylindrical.The microstructures of various regions were observed and analyzed by means of optical and scanning electron microscope.The tensile properties and microhardness were evaluated for the welded joint.From this investigation it is founded that the use of threaded pin profile of tool contributes to better flow of materials between two alloys and the generation of defect free stir zone.It also resulted in higher hardness values of 83 HV in the stir zone and higher tensile strength of 169 MPa compared to other two profiles.The increase in hardness is attributed to the formation of fine grains and intermetallics in the stir zone,and in addition,the reduced size of weaker regions,such as TMAZ and HAZ regions,results in higher tensile properties.
文摘Friction stir welding using the tools with polygonal pins is often found to improve the mechanical strength of weld joint in comparison to the tools with circular pins. However, the impacts of pin profile on the peak temperature, tool torque and traverse force, and the resultant mechanical stresses experienced by the tool have been rarely reported in a systematic manner. An estimation of the rate of heat generation for the tools with polygonal pins is challenging due to their non-axisymmetric cross-section about the tool axis. A novel methodology is presented to analytically estimate the rate of heat generation for the tools with polygonal pins. A three-dimensional heat transfer analysis of friction stir welding is carried out using finite element method. The computed temperature field from the heat transfer model is used to estimate the torque, traverse force and the mechanical stresses experienced by regular triangular, square, pentagon and hexagon pins following the principles of solid mechanics. The computed results show that the peak temperature experienced by the tool pin increases with the number of pin sides. However, the resultant maximum shear stress experienced by the pin reduces from the triangular to hexagonal pins.
文摘In order to prevent unwanted excited vibrations and to secure better machining precision in large size heavy duty machine tools dynamic stiffness is one of the most desirable and critical properties. In the past decades, many researches on machine tool stiffness test and evaluation methodology have been made. However any methodology for a Pin Turning Device (PTD), which is a special kind of turning lathe for machining big size crankshaft pins, is rarely found among them. This study proposes a test and evaluation process of stiffness of a PTD by measuring frequency response function at the tool center point (TCP). For conformance proving for the proposed methodology, stiffness of a PTD obtained by the proposed method with impact hammer test (IHT) has been compared with that determined by FEM.
