THE BASIC MECHANICS PROBLEMS AND THE DEVELOPMENT OF LONGWALL TOP-COAL CAVING TECHNIQUE IN CHINA

Since the middle of 1980’s, the longwall top-coal caving technique has beveloped rapidly in China. At present, it is one of the main approaches in the thick coal seam mining. This peper describes some mechanica problems of the caving technique, such as the damage and failure of the top-coal, the strata behaviors in the caving face, and the relation of the support and the surrounding rock. In order to employ the caving technique in a widespred scope, the problems such as the caving technique in the hard coal seam, the moving and running of the loose top-coal,and the upper floating of the gas etc. should be systematically systematically studied.

Study on gob-side entry retaining technique with roadside packing in longwall top-coal caving technology

Pointed out some technical difficulties of gob-side entry retaining with roadside packing in longwall top-coal caving technology (LTCT), and analyzed the function mecha-nism of roadside filling body. Theory analysis shows the mechanical properties of high water material fit for the feature of deformation of gob-side entry retaining in LTCT, and gob-side entry retaining in LTCT face is one of effective ways to increase the recovery ra-tio of mining district.

Key technologies and equipment for a fully mechanized top-coal caving operation with a large mining height at ultra-thick coal seams

Thick and ultra-thick coal seams are main coal seams for high production rate and high efficiency in Chinese coal mines, which accounts for 44 % of the total minable coal reserve. A fully mechanized top-coal caving mining method is a main underground coal extraction method for ultra-thick coal seams. The coal extraction technologies for coal seams less than 14 m thick were extensively used in China. However, for coal seams with thickness greater than 14 m, there have been no reported cases in the world for underground mechanical extraction with safe performance, high efficiency and high coal recovery ratio. To deal with this case, China Coal Technology ＆ Engineering Group, Datong Coal Mine Group, and other 15 organizations in China launched a fundamental and big project to develop coal mining technologies and equipment for coal seams with thicknesses greater than 14 m. After the completion of the project, a coal extraction method was developed for top-coal caving with a large mining height, as well as a ground control theory for ultra-thick coal seams. In addition, the mining technology for top-coal caving with a large mining height, the ground support technology for roadway in coal seams with a large cross-section, and the prevention and control technology for gas and fire hazards were developed and applied. Furthermore, a hydraulic support with a mining height of 5.2 m, a shearer with high reliability, and auxiliary equipment were developed and manufactured. Practical implication on the technologies and equipment developed was successfully completed at the No. 8105 coal face in the Tashan coal mine, Datong, China. The major achievements of the project are summarized as follows： 1. A top-coal caving method for ultra-thick coal seams is proposed with a cutting height of 5 m and a top-coal caving height of 15 m. A structural mechanical model of overlying strata called cantilever beam-articulated rock beam is established. Based on the model, the load resistance of the hydraulic support with a large mining height for top-coal caving method is determined. With the analysis, the movement characteristics of the top coal and above strata are evaluated during top-coal caving operation at the coal face with a large mining height. Furthermore, there is successful development of comprehensive technologies for preventing and controlling spalling of the coal wall, and the top-coal caving technology with high efficiency and high recovery at the top-coal caving face with a large mining height. This means that the technologies developed have overcome the difficulties in strata control, top-coal caving with high efficiency and high coal recovery, and enabled to achieve a production rate of more than 10 Mtpa at a single top-coal caving face with a large mining height in ultra-thick coal seams; 2. A hydraulic support with 5.2 m supporting height and anti-rockburst capacity, a shearer with high reliability, a scraper conveyor with a large power at the back of face, and a large load and long distance headgate belt conveyor have been successfully developed for a top-coal caving face with large mining height. The study has developed the key technologies for improving the reliability of equipment at the coal face and has overcome the challenges in equipping the top-coal caving face with a large mining height in ultra-thick coal seams; 3. The deformation characteristics of a large cross-section roadway in ultra-thick coal seams are discovered. Based on the findings above, a series of bolt materials with a high yielding strength of 500-830 MPa and a high extension ratio, and cable bolt material with a 1 × 19 structure, large tonnage and high extension ratio are developed. In addition, in order to achieve a safe roadway and a fast face advance, installation equipment for high pre-tension bolt is developed to solve the problems with the support of roadway in coal seams for top-coal caving operation with a large mining height; 4. The characteristics of gas distribution and uneven emission at top-coal caving face with large mining height in ultra-thick coal seams are evaluated. With the application of the technologies of gas drainage in the roof, the difficulties in gas control for high intensive top-coal caving mining operations, known as ＂low gas content, high gas emission＂, are solved. In addition, large flow-rate underground mobile equipment for making nitrogen are developed to solve the problems with fire prevention and safe mining at a top-coal caving face with large mining height and production rate of more than 10 Mtpa. A case study to apply the developed technologies has been conducted at the No. 8105 face, the Tashan coal mine in Datong, China. The case study demonstrates that the three units of equipment, i.e., the support, shearer and scraper conveyor, are rationally equipped. Average equipment usage at the coal face is 92.1%. The coal recovery ratio at the coal face is up to 88.9 %. In 2011, the coal production at the No. 8105 face reached 10.849 Mtpa, exceeding the target of 10 Mtpa for a topcoal caving operation with large mining height performed by Chinese-made mining equipment. The technologies and equipment developed provide a way for extracting ultra-thick coal seams. Currently, the technologies and equipment are used in 13 mining areas in China including Datong, Pingshuo, Shendong and Xinjiang. With the exploitation of coal resources in Western China, there is great potential for the application of the technologies and equipment developed.

Support-surrounding rock relationship and top-coal movement laws in large dip angle fully-mechanized caving face

When mining the fully-mechanized longwall caving face along strike, the unstable equipment, the low top-coal recovery ratio and the difficulty in controlling surrounding rock may occur due to large dip angle. Considering the effects of strike angle on support stability, the ‘‘support-surrounding rock"mechanical models of support topple and support slip were established in this paper. On the basis, the influencing factors of support stability were analyzed and the technical measures of controlling support and surrounding rock stability were put forward. Then the loose particles simulation experiment was conducted to analyze the impacts of caving directions and methods on the top-coal recovery in large dip angle fully-mechanized caving face. Finally, the ‘‘upward sequence and double-openings doublerounds" caving technology was determined. The research results are of great scientific significance and practical values to improve large dip thick seam mining technology.

Three-dimensional experimental study of loose top-coal drawing law for longwall top-coal caving mining technology

Based on the loose medium flow field theory, the loose top-coal drawing law of longwall top-coal caving（LTCC） mining technology is studied by using self-developed three-dimensional（3D） test device. The loose top-coal drawing test with shields and the controlled test without shields are performed in the condition without any boundary effect. Test results show that shields will cause reduction in drawing volume of coal in the LTCC mining. The deflection phenomenon of drawing body is also observed in the controlled test, which is verified that the deflection of drawing body is caused by shield. It is found that the deflection angle decreases with increasing caving height, with the maximum value of atailand the minimum value of 0. In addition, the formula to calculate the drawing volume is proposed subsequently.The deflection of drawing body is numerically simulated using particle flow code PFC3 Dand the proposed formula to calculate drawing volume in LTCC is also verified.

Distribution laws of abutment pressure around fully mechanized top-coal caving face by in-situ measurement

In order to obtain the distribution rules of abutment pressure around the 1151 （3） fully mechanized top-coal caving （FMTC） face of Xieqiao Colliery, the KSE-II-1 type bore-hole stress gauges were installed in the tailentry and headentry to measure the mining-induced stress. The distribution rules of the front and side abutment pressure were demonstrated. The results show that distribution rules of stress are obviously different in the vicinity of the face and entries. The peak value of abutment pressure in the protective coal pillar and face are located commonly in front of the working face along the strike, and they are located at the stress-decreased zone near the face. There is no stress peak value in the lateral coal mass beside the headentry in front of the face on the strike, and the peak value of abutment pressure appears at the rear area of the face. There are stress peak values both in the protective coal pillar and in the lateral coal mass beside the headentry to the dip.

SAFETY PROBLEMS IN FULLY-MECHANIZED TOP-COAL CAVING LONGWALL FACES

The thick-san top-ctal catrig technology has been in use in China for over a decade,and has given rise to siguscant economic efficiendes. Eftorts in reeent years to extend its applica tion to more complex mining conditions, mostly high-gas seams , with or without proneness ofspontaneous combustion. have brought about new safety problems This paper will highlight thefcatures and problems retared with thick-seam top-coal caving systems, compared with conventionai, fully-mecbanized longwall systems , particularly issues retated to methane, spontaneous combustion and dust,and disam the methods and measures to ded with them.

Surface Movement Regularity of Super-Wide Mining Face With Top-Coal Caving

No.4326 super-wide panel of Wangzhuang Coal Mine ( in which the fully-mechanized top-coal caving longwall mining method was used) was monitored for dynamic characteristic of surface movement. The dynamic surface movement in and after mining was predicted by using the Mining Subsidence Prediction System. The results indicate that after mining, the surface above the super-wide panel reaches a state of full subsidence, making the No.309 national highway above the panel be located on the flat bottom of the subsidence basin so that the influence of mining activity in both sides of 4326 panel on the national highway is the smallest.

Current Situation and Prospect of Top-Coal Caving Technology in China

A great development has been achieved on thick seam longwall top-coal caving technology in China for the recent years, which has raised face output and efficiency and reduced production cost greatly. In this paper, achievements in its production, safety and theoretical research and future tasks are discussed.

Longwall Top-Coal Caving in Thinner Thick-Seam and Research on Light Hydraulic Support

The application of light hydraulic support highlights the advantages of longwall top-coal caving (LTC) in thinner thick-seams (3. 0~ 5. 0 m). Considering the problems in practice, the developing of its new series will promote the mining of LTC with light hydraulic supports. Some relevant technical problems of the caving technology and the future of this series of supports are analyzed in this paper with several new opinions.

Study on Dust-Control WaterInjection in Fully-Mchanized Top-Coal Caving Longwall Faces

Based on the analysis of the top-coal movement, the appropriate position of holes through which dustcoutrol water is injected is confirmed. And a practical test has been carried out, which has achieved good reuslts both in dust control and in the flow rate of water injected into coal.

Numerical and theoretical investigations of the effect of the gangue-coal density ratio on the drawing mechanism in longwall top-coal caving

Discrete element calculations of the top-coal drawing process for diferent gangue-coal density ratios were conducted to investigate the efect of the gangue-coal density ratio on the drawing mechanism in longwall top-coal caving.The efects were analyzed for the drawing body,the top-coal boundary,and the recovery of top coal.The results show that for increasing density ratio,the initial drawing body on the goaf side is farther away from the drawing support and its width and volume gradually increase.The upper part of the sickle-shaped drawing body extends near the initial drawing body with increasing density ratio in the normal cycling stage,and the distance from the drawing body to the initial drawing body is its maximum width.The larger the density ratio,the smaller the height of the top coal above the goaf at the end of the initial drawing process.The height of the top-coal boundary decreases with increasing density ratio,until it reaches a limit.In a normal cycle,due to hysteretic development,the top-coal boundary moves toward the goaf until the density ratio is approximately 2.0,which is consistent with the physical experiment results.Finally,increasing the advance length of the working face is benefcial for increasing the overall recovery of top coal.

Analysis on air-leakage law of goal in condition of ascending mining for top-coal caving

Using the Jisan Coalmine's top-coal caving for the 3down coal seam with ascending mining as the project background, the air-leakage characteristics of the goaf wasanalyzed. Through data fitting of the in situ observation, the models of gas seepage, diffusion and air-leakage in the goaf were established in ascending mining. The ComputationFluid Dynamics software Fluent was used to simulate the air-leakage law of the goaf. Theresults of the numerical simulation provide a basis for the use of the technology of ventilation and fire prevention in the working face of an ascending mining, which ensures thesafety in production in the working face of the top-coal caving for 3_down coal seam in theJisan Coalmine.

Reliability analysis of the velocity matching of coal cutting and caving in fully mechanized top-coal caving face

The matching relationship between coal cutting and caving in fully mechanized top-coal caving face is analyzed in detail from the angle of reliability. The coupling equation of reliability is established correspondingly, and the mathematical equation of the coefficient of velocity matching of coal cutting and caving is obtained, which meets a certain reliability demand for making the working procedure of coal caving not influence coal cutting of coal-cutter. The results show that the relationship between the coefficient of the velocity matching and the reliability of coal cutting and caving system is linear on the whole when R <0.9. It is pointed out that different numerical value should be selected for different coal face according to different demand for reliability.

11世纪卫藏绘画的“波罗面相”研究

11世纪卫藏绘画艺术遗存数量很有限,却呈现出纷呈多样、错综复杂的样貌。按壁画、唐卡中人物面相,当以届时进入卫藏的东印度波罗艺术样式为主,以往的研究也认为,11世纪末叶出现的扎塘寺壁画中的人物其面相亦当如此。然而新的研究发现,扎塘寺人物面相与当时卫藏所绘均不相同,具有明确的独特性。文章系统地整理11世纪卫藏绘画遗存中不同类型的“波罗面相”版本,也对8-12世纪青藏高原系统吐蕃绘画不同系列的发展脉络给予梳理,重点探讨了扎塘寺壁画人物“长目型”“波罗面相”的艺术渊源。

莫高窟148窟药师经变中的建筑图像表达分析

净土经变是敦煌壁画盛唐时期的流行题材之一,其中大型建筑群成为讲经场面的重要背景。本文以148窟主室东壁北侧的药师经变为例,探讨敦煌大型经变壁画中建筑图像的绘制特征,从图面表现手法以及叙述特征的角度探讨该壁画中建筑物的位置关系。发现“正面—平行法”以及飞鸟投影法被同时运用到建筑图像的表达之中。配合“视阶”和多重视角的成熟运用,建筑群的庄重以及层层递进的环境感受得以凸显。

煤矿综放工作面旋转开采及其应用研究

受采区边界与断层的影响,按照常规对齐布置工作面切眼,将导致整个采区大量煤炭资源的损失。为最大限度地回收资源,以东滩煤矿1310工作面为研究对象,制定了一套合理的旋转开采方案,对刮板输送机上窜下滑控制、支架控制与输送机搭接、顶板控制等旋转开采关键技术进行分析,总结适用现场的工作方案。通过实地应用,该方案有效保障了工作面的正常回采,与常规布置相比,仅一个工作面就多回收煤炭资源6万t,提高了煤炭资源的回收率,取得了良好的社会效益和经济效益。

Investigation on the stress field characteristic of top coal at FMTC faces under the influence of caving thickness

In the background of the technology condition and the geological condition of the 1151（3） fully mechanized top-coal caving face （FMTC face）, and by means of taking nonlinear 3D numerical simulation, the stress redistribution rules of top coal with different thick coal seam were obtained by investigation on the numerical simulation of the redistributions of the stress with different coal seam＇s thickness. The research showes that there exists a certain difference on the stress distributions of the top coal at face, the maximum principal stress is located near to the tailentry＇s corner. The vertical stress＇s peak of the top coal decreases and the distance ahead of face position increases as the once mining thickness of the coal seam increases. At the same coal seam, the vertical stresses＇ peak of top coal gradually decreases from the top to the bottom, the peak＇s position is basically the same and its changes are gradually obvious with the thickness of coal seam increas- ing. The vertical stress of top coal places in a low stress state at a certain range ahead of face and over the face, which reveals the essence that the support loads are generally low under the condition of FMTC. The study supplies the theoretical foundation for the support design and selection, the theory of top coal＇s fragmentation, the movement rules of top coal and improving the recovery of top coal.

Application of preblasting to high-section top coal caving for steepthick coal sea

For mining extra-steep-thick coal seam, the sublevel top coal caving is a high efficient method in practical engineering. However, major challenges associated with mining high-section top-coal-caving （HSTCC） are related to the resulting high ground stresses. Inevitability, using the high-section sublevel top coal caving for extra-steep-thick coal seam, the large scale of mined-out area appears. If the prefracture blasting and hydraulic fracture techniques are utilized, the top coal damage and cracks will develop, and the mining complexity will increase, such as seam inclination, continuity, mechanical characteristics of roof and susceptibility of top coal, etc. First, the field conditions of B1＋2 seam were investigated at the ＋588 level of the Weihuliang Underground Mine of China. Subsequently, according to caving mechanism of strata response obtained from several special models including physical simulation tests and numerical simulation models, the prefracture process including blasting and injecting water were analyzed. Then, the prefracture blasting technique was successfully applied to the caving of 52 m-sublevel seam. Finally, the effects were verified by advanced detecting instruments, and the results show these methods and measurements are feasible and valid.

Control effect of fracture on hard coal cracking in a fully mechanized longwall top coal caving face

Through theoretical analysis, simulation test and practice, the law of a fracture'sinfluence on hard top coal press cracking was studied. The study focused on the relationbetween fracture and coal strength, top coal caving ability and work face layout. Based onthe investigation of the fracture system, the control of press cracking was achieved bymatching working face to fracture orientation to improve top-coal caving ability and recovery. The matching principle was pointed out: The top-coal caving working face should beperpendicular to or obliquely cross the primary fracture at a large angle, and cross thesecondary fracture at a small angle. The rational match can increase the recovery ratio oftop-coal and avoid rib spalling. The application of control technology on hard top coalpress cracking was introduced at the Iongwall top-coal caving face.