Three-dimensional experimental study of loose top-coal drawing law for longwall top-coal caving mining technology

Based on the loose medium flow field theory, the loose top-coal drawing law of longwall top-coal caving（LTCC） mining technology is studied by using self-developed three-dimensional（3D） test device. The loose top-coal drawing test with shields and the controlled test without shields are performed in the condition without any boundary effect. Test results show that shields will cause reduction in drawing volume of coal in the LTCC mining. The deflection phenomenon of drawing body is also observed in the controlled test, which is verified that the deflection of drawing body is caused by shield. It is found that the deflection angle decreases with increasing caving height, with the maximum value of atailand the minimum value of 0. In addition, the formula to calculate the drawing volume is proposed subsequently.The deflection of drawing body is numerically simulated using particle flow code PFC3 Dand the proposed formula to calculate drawing volume in LTCC is also verified.

Effect of wire diameter compression ratio on drawing deformation of micro copper wire

A crystal plasticity finite element model was developed for the drawing deformation of pure copper micro wire,based on rate-dependent crystal plasticity theory.The impact of wire diameter compression ratio on the micro-mechanical deformation behavior during the wire drawing process was investigated.Results indicate that the internal deformation and slip of the drawn wire are unevenly distributed,forming distinct slip and non-slip zones.Additionally,horizontal strain concentration bands develop within the drawn wire.As the wire diameter compression ratio increases,the strength of the slip systems and the extent of slip zones inside the deformation zone also increase.However,the fluctuating stress state,induced by contact pressure and frictional stress,results in a rough and uneven wire surface and diminishes the stability of the drawing process.

Modeling asymmetric fracture mechanics of Mg alloy wire in drawing process

In this study,a numerical analysis was conducted on the ductile fracture of a 2-mm diameter Mg-1Zn-0.5Mn-0.5Sr-0.1Ca alloy wire during drawing.The hexagonally close-packed crystal structure of Mg alloys causes asymmetric fracture behavior,especially in the compression region.The aim of this study is to develop a comprehensive damage model for Mg alloy wire that accurately predicts ductile fracture,with a focus on the compression region.A novel experimental method was introduced to measure the ductile fracture of Mg alloy wires under different stress states.The wire drawing process was simulated using the Generalized Incremental Stress-State dependent damage(GISSMO)Model and the Semi-Analytical Model for Polymers(SAMP)model.The damage model's prediction and the experimental results were found to be in excellent agreement,especially in determining crack initiation.Computational analysis established a safe zone diagram for die angle and reduction ratio,and experimental validation confirmed the feasibility of this approach.The proposed damage model can provide a practical and reliable analysis for optimizing the drawing process of Mg alloy wire.

Prediction of mechanical properties for deep drawing steel by deep learning

At present,iron and steel enterprises mainly use“after spot test ward”to control final product quality.However,it is impossible to realize on-line quality predetermining for all products by this traditional approach,hence claims and returns often occur,resulting in major eco-nomic losses of enterprises.In order to realize the on-line quality predetermining for steel products during manufacturing process,the predic-tion models of mechanical properties based on deep learning have been proposed in this work.First,the mechanical properties of deep drawing steels were predicted by using LSTM(long short team memory),GRU(gated recurrent unit)network,and GPR(Gaussian process regression)model,and prediction accuracy and learning efficiency for different models were also discussed.Then,on-line re-learning methods for transfer learning models and model parameters were proposed.The experimental results show that not only the prediction accuracy of optimized trans-fer learning models has been improved,but also predetermining time was shortened to meet real time requirements of on-line property prede-termining.The industrial production data of interstitial-free(IF)steel was used to demonstrate that R2 value of GRU model in training stage reaches more than 0.99,and R2 value in testing stage is more than 0.96.

Mating model on production capacity for the system of cutting coal and drawing top-coal in FMMSC

Being a safe and highly-efficient mining method, fully mechanized mining with sublevel caving （FMMSC） was extensively employed in Chinese coal mines with thick seam. In order to make drawing top-coal furthest to parallel work with shearer cutting coal, decrease failure ratio of rear scraper conveyor and increase safe production capacity of equipments, based on production technology, set up the mating model of safe production capacity of equipments for the system of drawing top-coal and shearer cutting coal in coal face with sublevel caving. It is mean capability of drawing top-coal adapted to the capability of shearer cutting coal in a working circle in the coal face that was deduced. The type selection of equipment of rear scraper conveyor can be tackled with this mating model. The model was applied in FMMSC in Yangcun Coal Mine, Yima Coal Group of China. With the mating light-equipments, the coal output in coal face attained 1.05 Mt in 2004. It gained better technical-economic benefit.

Numerical and theoretical investigations of the effect of the gangue-coal density ratio on the drawing mechanism in longwall top-coal caving

Discrete element calculations of the top-coal drawing process for diferent gangue-coal density ratios were conducted to investigate the efect of the gangue-coal density ratio on the drawing mechanism in longwall top-coal caving.The efects were analyzed for the drawing body,the top-coal boundary,and the recovery of top coal.The results show that for increasing density ratio,the initial drawing body on the goaf side is farther away from the drawing support and its width and volume gradually increase.The upper part of the sickle-shaped drawing body extends near the initial drawing body with increasing density ratio in the normal cycling stage,and the distance from the drawing body to the initial drawing body is its maximum width.The larger the density ratio,the smaller the height of the top coal above the goaf at the end of the initial drawing process.The height of the top-coal boundary decreases with increasing density ratio,until it reaches a limit.In a normal cycle,due to hysteretic development,the top-coal boundary moves toward the goaf until the density ratio is approximately 2.0,which is consistent with the physical experiment results.Finally,increasing the advance length of the working face is benefcial for increasing the overall recovery of top coal.

Tianmen textile machinery:Independently developed the drawing frame equipment

Hubei Tianmen Textile Machinery Co.,Ltd.is a well-known enterprise and key high-tech enterprise in China textile industry.The company's leading product,drawing frame,has completely independent intellectual property rights,among which TM 11 is well received by users and has a high market share in China.

Research on the Reform of the Course“Reading of Concrete Structure Plan and Construction Drawings”Under the Background of“Promoting Teaching and Learning Through Competitions”

The inherent teaching approach can no longer meet the demands of society.In this paper,current issues within the teaching landscape of architectural engineering technology in higher vocational colleges as well as the policies and teaching demands that formed the basis of this model were analyzed.The study shows the importance of the implementation of the teaching model“promoting teaching and learning through competitions.”This model puts emphasis on the curriculum and teaching resources,while also integrating the teaching process and evaluation with competition.These efforts aim to drive education reform in order to better align with the objectives of vocational education personnel training,while also acting as a reference for similar courses.

基于知识结构差异的CorelDRAW服装设计课程改革与实践

文章分析了“新文科”建设内涵,基于海口经济学院南海美术学院2021级服装与服饰设计专业学生的知识结构差异,对Corel DRAW服装设计课程教学方法、教学思路、考核方式等进行改革,优化教学设计,将海南地域文化、时尚创意思维融入课程内容,以项目伴随式、任务驱动式等方法开展教学,结课作业和服装设计大赛相结合,全面激发学生的思想内核和学习动力,取得了诸多教学成果,为设计类专业软件课程改革提供了新思路。

Influence of drawing process parameters on forming of micro copper tube with straight grooves

Using high-speed oil-filled spinning method,high quality micro copper tube with straight grooves（MCTSG） with an outer diameter of 6 mm was obtained.Then,MCTSG with an outer diameter of 3-6 mm was fabricated successfully by multi-pass drawing processing method.The influence of drawing parameters on the forming of micro straight grooves was investigated based on the forming mechanism.The results show that the values of groove depth and width decrease,while the wall thickness increases as the drawing diameter decreases.At the same time,the groove depth and width increase,while the wall thickness decreases as the die angle increases.The drawing force increases as the reduction increases.Excessive copper tube reduction may results in groove folding and segmental teeth.The drawing force decreases firstly and then increases with the increases in die angle.When the die angle α is 16°,the drawing force is the smallest,indicating 16° is the optimal angle.

Microstructure and texture of commercially pure titanium in cold deep drawing

The development of microstructure and texture during cold deep drawing of commercially pure titanium（CP-Ti） was investigated.Three parts,stretching region,drawing region and flange region,were sequentially formed in the deep drawing process of the hemispheric surface part,with reference to deformation modes and strain regimes.Results show that the plastic strain is accommodated by dislocation slip and deformation twinning in the whole deep drawing process.The texture of the CP-Ti sheet and its drawn part consists of rolling texture component and recrystallization texture component.The intensity and type of the initial texture varied during the drawing process are related to the production of deformation twinning and dislocation slip.Twinning weakens the initial texture by randomizing the orientations of crystals,especially for the recrystallization texture.The recrystallization texture in the drawing region disappears due to the significant forming of twinning.Furthermore,over drawing would result in the predominance of dislocation slip and the texture is strengthened.

Texture evolution and its simulation of cold drawing copper wires produced by continuous casting

The texture evolution of cold drawing copper wires produced by continuous casting was measured by X-ray diffractometry and electron back-scatter diffractometry,and was simulated using Taylor model.The results show that in the drawn poly-crystal copper wires produced by traditional continuous casting,111 and 100 duplex fiber texture forms,and with increasing strain,the intensities of 111 and 100 increase.In the drawn single-crystal copper wires produced by Ohno continuous casting,100 rotates to 111,and there is inhomogeneous distribution of fiber texture along radial direction of the wires,which is caused by the distribution of shear deformation.Compared with 100,111 fiber texture is more stable in the drawn copper wires.Comparison of the experimental results with the simulated results shows that the simulation by Taylor model can analyze the texture evolution of drawn copper wires.

Effect of electropulsing on deformation behavior of Ti-6Al-4V alloy during cold drawing

Electron backscattered diffraction （EBSD） and transmission electron microscopy （TEM） were used to investigate effect of electropulsing on microstructure and texture evolution of Ti-6Al-4V during cold drawing. Research results demonstrate that the electropulsing treatment （EPT） can enhance the deformability of the grains with unfavorable orientations, which makes the compatibility of deformation among grains much better. A comparison in texture evolution between conventional cold drawing and EPT cold drawing indicates that the EPT promotes prismatic 〈a〉 slip moving, restricts pyramidal 〈c＋a〉 slip occurring and accommodates the deformation with c-component by grain boundary sliding. The fraction decrease of low-angle grain boundaries for samples deformed with EPT reveals that the application of electropulsing restricts the formation of the incidental dislocation boundaries and the geometrically necessary boundaries.

Effects of stress state on texture and microstructure in cold drawing-bulging of CP-Ti sheet

Three different stress states of the combination of tensile（t） stress and compressive（c） stress,t t,t c and t c c,exist in the deformed commercially pure titanium（CP-Ti） sheet during cold drawing-bulging.The textures and microstructures in the different stress state regions were investigated by means of XRD and TEM analysis.Similar development of texture and microstructure is achieved with less thickness strain under multiaxial stresses in drawing-bulging than in cold rolling.The results show that texture and microstructure are much sensitive to multiaxial stresses.Twinning is more easily activated under compressive stress than tensile stress.Prism a slip is heavily affected by tensile stress,resulting in a remarkable change of the intensity of（0°,35°,0°） texture,while pyramidal c＋a slip,forming（20°,35°,30°） texture,weakens with the increase of thickness strain in spite of stress state.

Application of ultra-smooth composite diamond film coated WC-Co drawing dies under water-lubricating conditions

A specific revised HFCVD apparatus and a novel process combining HFCVD and polishing technique were presented to deposit the micro-and nano-crystalline multilayered ultra-smooth diamond（USCD） film on the interior-hole surface of WC-Co drawing dies with aperture ranging from d1.0 mm to 60 mm.Characterization results indicate that the surface roughness values（Ra） in the entry zone,drawing zone and bearing zone of as-fabricated USCD coated drawing die were measured as low as 25.7,23.3 and 25.5 nm,respectively.Furthermore,the friction properties of USCD films were examined in both dry sliding and water-lubricating conditions,and the results show that the USCD film presents much superior friction properties.Its friction coefficients against ball-bearing steel,copper and silicon nitride balls（d4 mm）,is always lower than that of microcrystalline diamond（MCD） or WC-Co sample,regardless of the lubricating condition.Meanwhile,it still presents competitive wear resistance with the MCD films.Finally,the working lifetime and performance of as-fabricated USCD coated drawing dies were examined under producing low-carbon steel pipes in dry-sliding and water-lubricating conditions.Under the water-lubricating drawing condition,its production significantly increases by about 20 times compared with the conventional WC-Co drawing dies.

Flexible die drawing of magnesium alloy sheet by superimposing ultrasonic vibration

Combining solid granule medium forming technology with ultrasonic vibration plastic forming technology, ultrasonic vibration granule medium forming （UGMF） technology was proposed. To reveal the effect of ultrasonic vibration on flexible-die deep drawing, an ultrasonic vibration with a frequency of 20 kHz and a maximum output of 1.5 kW was on the solid granule medium deep drawing of AZ31B magnesium alloy sheet. The results revealed that ultrasonic vibration promotes the pressure transmission performance of the granule medium and the formability of the sheet. The forming load declines with the ultrasonic amplitude during the drawing process as a result of the combined influence of the ＂surface effect＂ and the ＂softening＂ of the ＂volume effect＂.

Effects of tribological behavior of DLC film on micro-deep drawing processes

To decrease the size effects of friction in microforming, three kinds of surface coatings, such as diamond-like carbon（DLC）, TiN and MoS2, were deposited on surfaces of dies with plasma based ion implantation and deposition（PBII D） method and magnetron sputtering technique, respectively. The tribological behavior of surface coatings was analyzed considering plastic deformation of specimen at contact interface. The analyses indicate that there is a lower coefficient of friction（COF） and a high wear resistance under the condition of large strain/stress when using the DLC film. The graphitization of DLC film occurs after 100 times of tests. The mechanism of graphitization was analyzed considering energy induced by friction work. The effects of DLC film properties on qualities of micro-deep drawn parts were investigated by analyzing the reduction of wall thickness, etc. The results indicate that DLC film is very helpful for improving the qualities of the micro-parts.

基于Visio Drawing Control控件的图形化潮流计算软件开发

针对VC,Delphi等工具开发电力系统分析计算软件图形可视化的缺陷,提出并研究了一种基于VisioDrawing Control图形控件,利用VC进行二次开发的图形化电力系统潮流计算软件开发的技术,研究了基于该控件的图形化建模方法及电网拓扑结构的自动识别,开发了实用的电力系统图形化潮流计算软件.实践表明,基于Visio Drawing Control的二次开发技术为图形化电力系统潮流计算软件的开发提供了新的有效的途径.

工程图协同审议与存档管理系统VHDrawings的设计与实现

工程设计单位的审图工作是一个需要多人参与、多次往复的过程。用传统的方法传递设计图与修改意见,速度慢且易出错,限制了工程设计单位工作效率的提高。该文介绍了一个计算机辅助的工程图协同审议与存档管理系统VHDrawings的设计与实现。着重讨论了协同审图工作流的管理以及工程图自动识别技术在图档管理中的应用。为设计单位提高工作效率、优化管理流程提供了一种参考。

Graphical Simulator for Chinese Ink-Wash Drawing

Simulating the traditional painting art by computer graphics is a challenging and attractive subject. Basing on the experience in the ink wash drawing, in this paper, we expound the artistic characters of ink wash painting and particularly analyze the characteristics of the materials used in the ink wash drawing and the relationships between them. A simulation model is presented and some typical visual effects of the ink wash painting are realized.